| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The ARM SMMU drivers provide a DOMAIN_ATTR_NESTING domain attribute,
which allows callers of the IOMMU API to request that the page table
for a domain is installed at stage-2, if supported by the hardware.
Since setting this attribute only makes sense for UNMANAGED domains,
this patch returns -ENODEV if the domain_{get,set}_attr operations are
called on other domain types.
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
The current SMR masking support using a 2-cell iommu-specifier is
primarily intended to handle individual masters with large and/or
complex Stream ID assignments; it quickly gets a bit clunky in other SMR
use-cases where we just want to consistently mask out the same part of
every Stream ID (e.g. for MMU-500 configurations where the appended TBU
number gets in the way unnecessarily). Let's add a new property to allow
a single global mask value to better fit the latter situation.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Nipun Gupta <nipun.gupta@nxp.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
On relatively slow development platforms and software models, the
inefficiency of our TLB sync loop tends not to show up - for instance on
a Juno r1 board I typically see the TLBI has completed of its own accord
by the time we get to the sync, such that the latter finishes instantly.
However, on larger systems doing real I/O, it's less realistic for the
TLBs to go idle immediately, and at that point falling into the 1MHz
polling loop turns out to throw away performance drastically. Let's
strike a balance by polling more than once between pauses, such that we
have much more chance of catching normal operations completing before
committing to the fixed delay, but also backing off exponentially, since
if a sync really hasn't completed within one or two "reasonable time"
periods, it becomes increasingly unlikely that it ever will.
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
TLB synchronisation typically involves the SMMU blocking all incoming
transactions until the TLBs report completion of all outstanding
operations. In the common SMMUv2 configuration of a single distributed
SMMU serving multiple peripherals, that means that a single unmap
request has the potential to bring the hammer down on the entire system
if synchronised globally. Since stage 1 contexts, and stage 2 contexts
under SMMUv2, offer local sync operations, let's make use of those
wherever we can in the hope of minimising global disruption.
To that end, rather than add any more branches to the already unwieldy
monolithic TLB maintenance ops, break them up into smaller, neater,
functions which we can then mix and match as appropriate.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
ARM_AMMU_CB() is calculated relative to ARM_SMMU_CB_BASE(), but the
latter is never of use on its own, and what we end up with is the same
ARM_SMMU_CB_BASE() + ARM_AMMU_CB() expression being duplicated at every
callsite. Folding the two together gives us a self-contained context
bank accessor which is much more pleasant to work with.
Secondly, we might as well simplify CB_BASE itself at the same time.
We use the address space size for its own sake precisely once, at probe
time, and every other usage is to dynamically calculate CB_BASE over
and over and over again. Let's flip things around so that we just
maintain the CB_BASE address directly.
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Calculating ASIDs/VMIDs dynamically from arm_smmu_cfg was a neat trick,
but the global uniqueness workaround makes it somewhat more awkward, and
means we end up having to pass extra state around in certain cases just
to keep a handle on the offset.
We already have 16 bits going spare in arm_smmu_cfg; let's just
precalculate an ASID/VMID, plop it in there, and tidy up the users
accordingly. We'd also need something like this anyway if we ever get
near to thinking about SVM, so it's no bad thing.
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
16-bit ASID should be enabled before initializing TTBR0/1,
otherwise only LSB 8-bit ASID will be considered. Hence
moving configuration of TTBCR register ahead of TTBR0/1
while initializing context bank.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
[will: rewrote comment]
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Firmware is responsible for properly enabling smmu workarounds. Print
a message for better diagnostics when Cavium erratum 27704 was
detected.
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Make use of the iommu_device_register() interface.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Register hardware IOMMUs seperatly with the iommu-core code
and add a sysfs representation of the iommu topology.
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
With IOVA allocation suitably tidied up, we are finally free to opt in
to the per-CPU caching mechanism. The caching alone can provide a modest
improvement over walking the rbtree for weedier systems (iperf3 shows
~10% more ethernet throughput on an ARM Juno r1 constrained to a single
650MHz Cortex-A53), but the real gain will be in sidestepping the rbtree
lock contention which larger ARM-based systems with lots of parallel I/O
are starting to feel the pain of.
Reviewed-by: Nate Watterson <nwatters@codeaurora.org>
Tested-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Now that allocation is suitably abstracted, our private alloc/free
helpers can drive the trivial MSI cookie allocator directly as well,
which lets us clean up its exposed guts from iommu_dma_map_msi_msg() and
simplify things quite a bit.
Reviewed-by: Nate Watterson <nwatters@codeaurora.org>
Tested-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
In preparation for some IOVA allocation improvements, clean up all the
explicit struct iova usage such that all our mapping, unmapping and
cleanup paths deal exclusively with addresses rather than implementation
details. In the process, a few of the things we're touching get renamed
for the sake of internal consistency.
Reviewed-by: Nate Watterson <nwatters@codeaurora.org>
Tested-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
To make vfio support subchannel devices, we need a css driver for
the vfio subchannels. This patch adds a basic vfio-ccw subchannel
driver for this purpose.
To enable VFIO for vfio-ccw, enable S390_CCW_IOMMU config option
and configure VFIO as required.
Acked-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Message-Id: <20170317031743.40128-5-bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
Currently, amd_iommu_pc_get_set_reg_val() cannot support multiple
IOMMUs. Modify it to allow callers to specify an IOMMU. This is in
preparation for supporting multiple IOMMUs.
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Jörg Rödel <joro@8bytes.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: iommu@lists.linux-foundation.org
Link: http://lkml.kernel.org/r/1487926102-13073-8-git-send-email-Suravee.Suthikulpanit@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Currently, amd_iommu_pc_get_max_[banks|counters]() use end-point device
ID to locate an IOMMU and check the reported max banks/counters. The
logic assumes that the IOMMU_BASE_DEVID belongs to the first IOMMU, and
uses it to acquire a reference to the first IOMMU, which does not work
on certain systems. Instead, modify the function to take an IOMMU index,
and use it to query the corresponding AMD IOMMU instance.
Currently, hardcode the IOMMU index to 0 since the current AMD IOMMU
perf implementation supports only a single IOMMU. A subsequent patch
will add support for multiple IOMMUs, and will use a proper IOMMU index.
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Jörg Rödel <joro@8bytes.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: iommu@lists.linux-foundation.org
Link: http://lkml.kernel.org/r/1487926102-13073-7-git-send-email-Suravee.Suthikulpanit@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Introduce amd_iommu_get_num_iommus(), which returns the value of
amd_iommus_present. The function is used to replace direct access to the
variable, which is now declared as static.
This function will also be used by AMD IOMMU perf driver.
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Jörg Rödel <joro@8bytes.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: iommu@lists.linux-foundation.org
Link: http://lkml.kernel.org/r/1487926102-13073-6-git-send-email-Suravee.Suthikulpanit@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Clean up coding style and fix a bug in the 64-bit register read logic
since it overwrites the upper 32-bit when reading the lower 32-bit.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Jörg Rödel <joro@8bytes.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: iommu@lists.linux-foundation.org
Link: http://lkml.kernel.org/r/1487926102-13073-5-git-send-email-Suravee.Suthikulpanit@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
When booting into a kexec kernel with intel_iommu=off, and
the previous kernel had intel_iommu=on, the IOMMU hardware
is still enabled and gets not disabled by the new kernel.
This causes the boot to fail because DMA is blocked by the
hardware. Disable the IOMMUs when we find it enabled in the
kexec kernel and boot with intel_iommu=off.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
SYSMMU v5 has dedicated registers to perform TLB flush range operation,
so use them instead of looping with FLUSH_ENTRY command.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
IOMMU domain allocation is not performance critical operation, so remove
hand made optimisation of unrolled initialization loop and leave this to
the compiler.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
|
|
Now that we're applying the IOMMU API reserved regions to our IOVA
domains, we shouldn't need to privately special-case PCI windows, or
indeed anything else which isn't specific to our iommu-dma layer.
However, since those aren't IOMMU-specific either, rather than start
duplicating code into IOMMU drivers let's transform the existing
function into an iommu_get_resv_regions() helper that they can share.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Now that it's simple to discover the necessary reservations for a given
device/IOMMU combination, let's wire up the appropriate handling. Basic
reserved regions and direct-mapped regions we simply have to carve out
of IOVA space (the IOMMU core having already mapped the latter before
attaching the device). For hardware MSI regions, we also pre-populate
the cookie with matching msi_pages. That way, irqchip drivers which
normally assume MSIs to require mapping at the IOMMU can keep working
without having to special-case their iommu_dma_map_msi_msg() hook, or
indeed be aware at all of quirks preventing the IOMMU from translating
certain addresses.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Even if a host controller's CPU-side MMIO windows into PCI I/O space do
happen to leak into PCI memory space such that it might treat them as
peer addresses, trying to reserve the corresponding I/O space addresses
doesn't do anything to help solve that problem. Stop doing a silly thing.
Fixes: fade1ec055dc ("iommu/dma: Avoid PCI host bridge windows")
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The introduction of reserved regions has left a couple of rough edges
which we could do with sorting out sooner rather than later. Since we
are not yet addressing the potential dynamic aspect of software-managed
reservations and presenting them at arbitrary fixed addresses, it is
incongruous that we end up displaying hardware vs. software-managed MSI
regions to userspace differently, especially since ARM-based systems may
actually require one or the other, or even potentially both at once,
(which iommu-dma currently has no hope of dealing with at all). Let's
resolve the former user-visible inconsistency ASAP before the ABI has
been baked into a kernel release, in a way that also lays the groundwork
for the latter shortcoming to be addressed by follow-up patches.
For clarity, rename the software-managed type to IOMMU_RESV_SW_MSI, use
IOMMU_RESV_MSI to describe the hardware type, and document everything a
little bit. Since the x86 MSI remapping hardware falls squarely under
this meaning of IOMMU_RESV_MSI, apply that type to their regions as well,
so that we tell the same story to userspace across all platforms.
Secondly, as the various region types require quite different handling,
and it really makes little sense to ever try combining them, convert the
bitfield-esque #defines to a plain enum in the process before anyone
gets the wrong impression.
Fixes: d30ddcaa7b02 ("iommu: Add a new type field in iommu_resv_region")
Reviewed-by: Eric Auger <eric.auger@redhat.com>
CC: Alex Williamson <alex.williamson@redhat.com>
CC: David Woodhouse <dwmw2@infradead.org>
CC: kvm@vger.kernel.org
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
For some unknown reasons, in some cases, FLPD cache invalidation doesn't
work properly with SYSMMU v5 controllers found in Exynos5433 SoCs. This
can be observed by a firmware crash during initialization phase of MFC
video decoder available in the mentioned SoCs when IOMMU support is
enabled. To workaround this issue perform a full TLB/FLPD invalidation
in case of replacing any first level page descriptors in case of SYSMMU v5.
Fixes: 740a01eee9ada ("iommu/exynos: Add support for v5 SYSMMU")
CC: stable@vger.kernel.org # v4.10+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Documentation specifies that SYSMMU should be in blocked state while
performing TLB/FLPD cache invalidation, so add needed calls to
sysmmu_block/unblock.
Fixes: 66a7ed84b345d ("iommu/exynos: Apply workaround of caching fault page table entries")
CC: stable@vger.kernel.org # v4.10+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Usual pattern when we check for return code, which might be negative
errno, is either (ret) or (!ret).
Remove extra ' != 0' from condition.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
There is no need to assign ret to 0 in some cases. Moreover it might
shadow some errors in the future.
Remove such assignments.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
There is no need to have a temporary variable.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
There is inconsistency in return codes across the functions called from
detect_intel_iommu().
Make it consistent and propagate return code to the caller.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The function device_to_iommu() in the Intel VT-d driver
lacks a NULL-ptr check, resulting in this oops at boot on
some platforms:
BUG: unable to handle kernel NULL pointer dereference at 00000000000007ab
IP: [<ffffffff8132234a>] device_to_iommu+0x11a/0x1a0
PGD 0
[...]
Call Trace:
? find_or_alloc_domain.constprop.29+0x1a/0x300
? dw_dma_probe+0x561/0x580 [dw_dmac_core]
? __get_valid_domain_for_dev+0x39/0x120
? __intel_map_single+0x138/0x180
? intel_alloc_coherent+0xb6/0x120
? sst_hsw_dsp_init+0x173/0x420 [snd_soc_sst_haswell_pcm]
? mutex_lock+0x9/0x30
? kernfs_add_one+0xdb/0x130
? devres_add+0x19/0x60
? hsw_pcm_dev_probe+0x46/0xd0 [snd_soc_sst_haswell_pcm]
? platform_drv_probe+0x30/0x90
? driver_probe_device+0x1ed/0x2b0
? __driver_attach+0x8f/0xa0
? driver_probe_device+0x2b0/0x2b0
? bus_for_each_dev+0x55/0x90
? bus_add_driver+0x110/0x210
? 0xffffffffa11ea000
? driver_register+0x52/0xc0
? 0xffffffffa11ea000
? do_one_initcall+0x32/0x130
? free_vmap_area_noflush+0x37/0x70
? kmem_cache_alloc+0x88/0xd0
? do_init_module+0x51/0x1c4
? load_module+0x1ee9/0x2430
? show_taint+0x20/0x20
? kernel_read_file+0xfd/0x190
? SyS_finit_module+0xa3/0xb0
? do_syscall_64+0x4a/0xb0
? entry_SYSCALL64_slow_path+0x25/0x25
Code: 78 ff ff ff 4d 85 c0 74 ee 49 8b 5a 10 0f b6 9b e0 00 00 00 41 38 98 e0 00 00 00 77 da 0f b6 eb 49 39 a8 88 00 00 00 72 ce eb 8f <41> f6 82 ab 07 00 00 04 0f 85 76 ff ff ff 0f b6 4d 08 88 0e 49
RIP [<ffffffff8132234a>] device_to_iommu+0x11a/0x1a0
RSP <ffffc90001457a78>
CR2: 00000000000007ab
---[ end trace 16f974b6d58d0aad ]---
Add the missing pointer check.
Fixes: 1c387188c60f53b338c20eee32db055dfe022a9b ("iommu/vt-d: Fix IOMMU lookup for SR-IOV Virtual Functions")
Signed-off-by: Koos Vriezen <koos.vriezen@gmail.com>
Cc: stable@vger.kernel.org # 4.8.15+
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This patch consolidates almost the same code used in iova_insert_rbtree()
and __alloc_and_insert_iova_range() functions. While touching this code,
replace BUG() with WARN_ON(1) to avoid taking down the whole system in
case of corrupted iova tree or incorrect calls.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Do a check for already installed leaf entry at the current level before
dereferencing it in order to avoid walking the page table down with
wrong pointer to the next level.
Signed-off-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
CC: Will Deacon <will.deacon@arm.com>
CC: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Do a check for already installed leaf entry at the current level before
dereferencing it in order to avoid walking the page table down with
wrong pointer to the next level.
Signed-off-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
CC: Will Deacon <will.deacon@arm.com>
CC: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
We are going to split <linux/sched/mm.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/mm.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
The APIs that are going to be moved first are:
mm_alloc()
__mmdrop()
mmdrop()
mmdrop_async_fn()
mmdrop_async()
mmget_not_zero()
mmput()
mmput_async()
get_task_mm()
mm_access()
mm_release()
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The link between the iommu sysfs-device and the struct
amd_iommu is no longer stored as driver-data. Update the
code to the new correct way of getting from device to
amd_iommu.
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Fixes: 39ab9555c241 ('iommu: Add sysfs bindings for struct iommu_device')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The link between the iommu sysfs-device and the struct
intel_iommu is no longer stored as driver-data. Update the
code to use the new access method.
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Fixes: 39ab9555c241 ('iommu: Add sysfs bindings for struct iommu_device')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
We already have the helper, we can convert the rest of the kernel
mechanically using:
git grep -l 'atomic_inc_not_zero.*mm_users' | xargs sed -i 's/atomic_inc_not_zero(&\(.*\)->mm_users)/mmget_not_zero\(\1\)/'
This is needed for a later patch that hooks into the helper, but might
be a worthwhile cleanup on its own.
Link: http://lkml.kernel.org/r/20161218123229.22952-3-vegard.nossum@oracle.com
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull rdma DMA mapping updates from Doug Ledford:
"Drop IB DMA mapping code and use core DMA code instead.
Bart Van Assche noted that the ib DMA mapping code was significantly
similar enough to the core DMA mapping code that with a few changes it
was possible to remove the IB DMA mapping code entirely and switch the
RDMA stack to use the core DMA mapping code.
This resulted in a nice set of cleanups, but touched the entire tree
and has been kept separate for that reason."
* tag 'for-next-dma_ops' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (37 commits)
IB/rxe, IB/rdmavt: Use dma_virt_ops instead of duplicating it
IB/core: Remove ib_device.dma_device
nvme-rdma: Switch from dma_device to dev.parent
RDS: net: Switch from dma_device to dev.parent
IB/srpt: Modify a debug statement
IB/srp: Switch from dma_device to dev.parent
IB/iser: Switch from dma_device to dev.parent
IB/IPoIB: Switch from dma_device to dev.parent
IB/rxe: Switch from dma_device to dev.parent
IB/vmw_pvrdma: Switch from dma_device to dev.parent
IB/usnic: Switch from dma_device to dev.parent
IB/qib: Switch from dma_device to dev.parent
IB/qedr: Switch from dma_device to dev.parent
IB/ocrdma: Switch from dma_device to dev.parent
IB/nes: Remove a superfluous assignment statement
IB/mthca: Switch from dma_device to dev.parent
IB/mlx5: Switch from dma_device to dev.parent
IB/mlx4: Switch from dma_device to dev.parent
IB/i40iw: Remove a superfluous assignment statement
IB/hns: Switch from dma_device to dev.parent
...
|
|
The callers of the DMA alloc functions already provide the proper
context GFP flags. Make sure to pass them through to the CMA allocator,
to make the CMA compaction context aware.
Link: http://lkml.kernel.org/r/20170127172328.18574-3-l.stach@pengutronix.de
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Radim Krcmar <rkrcmar@redhat.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Alexander Graf <agraf@suse.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
By default CONFIG_INTEL_IOMMU_DEFAULT_ON is not set and thus
dmar_disabled variable is set.
Intel IOMMU driver based on above doesn't set intel_iommu_enabled
variable.
The commit b0119e870837 ("iommu: Introduce new 'struct iommu_device'")
mistakenly assumes it never happens and tries to unregister not ever
registered resources, which crashes the kernel at boot time:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: iommu_device_unregister+0x31/0x60
Make unregister procedure conditional in free_iommu().
Fixes: b0119e870837 ("iommu: Introduce new 'struct iommu_device'")
Cc: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
|
|
And also move its remaining functionality to
iommu_device_register() and 'struct iommu_device'.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Register Exynos IOMMUs to the IOMMU core and make them
visible in sysfs. This patch does not add the links between
IOMMUs and translated devices yet.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Register individual Mediatek IOMMUs to the iommu core and
add sysfs entries.
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Register the MSM IOMMUs to the iommu core and add sysfs
entries for that driver.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Also add the smmu devices to sysfs.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This makes the interface more consistent with
iommu_device_sysfs_add/remove.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
Will Deacon
Robin Murphy
Sunil Goutham
Robert Richter
Joerg Roedel
Dong Jia Shi
Suravee Suthikulpanit
Marek Szyprowski
Andy Shevchenko
Koos Vriezen
Oleksandr Tyshchenko
Ingo Molnar
Vegard Nossum
Linus Torvalds
Lucas Stach