| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The MIPS GIC contains a block of registers used to map local interrupts
to a particular CPU interrupt pin. Since these registers are found at a
consecutive range of addresses we access them using an index, via the
(read|write)_gic_v[lo]_map accessor functions. We currently use values
from enum mips_gic_local_interrupt as those indices.
Unfortunately whilst enum mips_gic_local_interrupt provides the correct
offsets for bits in the pending & mask registers, the ordering of the
map registers is subtly different... Compared with the ordering of
pending & mask bits, the map registers move the FDC from the end of the
list to index 3 after the timer interrupt. As a result the performance
counter & software interrupts are therefore at indices 4-6 rather than
indices 3-5.
Notably this causes problems with performance counter interrupts being
incorrectly mapped on some systems, and presumably will also cause
problems for FDC interrupts.
Introduce a function to map from enum mips_gic_local_interrupt to the
index of the corresponding map register, and use it to ensure we access
the map registers for the correct interrupts.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: a0dc5cb5e31b ("irqchip: mips-gic: Simplify gic_local_irq_domain_map()")
Fixes: da61fcf9d62a ("irqchip: mips-gic: Use irq_cpu_online to (un)mask all-VP(E) IRQs")
Reported-and-tested-by: Archer Yan <ayan@wavecomp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Commit 7778c4b27cbe ("irqchip: mips-gic: Use pcpu_masks to avoid reading
GIC_SH_MASK*") removed the read of the hardware mask register when
handling shared interrupts, instead using the driver's shadow pcpu_masks
entry as the effective mask. Unfortunately this did not take account of
the write to pcpu_masks during gic_shared_irq_domain_map, which
effectively unmasks the interrupt early. If an interrupt is asserted,
gic_handle_shared_int decodes and processes the interrupt even though it
has not yet been unmasked via gic_unmask_irq, which also sets the
appropriate bit in pcpu_masks.
On the MIPS Boston board, when a console command line of
"console=ttyS0,115200n8r" is passed, the modem status IRQ is enabled in
the UART, which is immediately raised to the GIC. The interrupt has been
mapped, but no handler has yet been registered, nor is it expected to be
unmasked. However, the write to pcpu_masks in gic_shared_irq_domain_map
has effectively unmasked it, resulting in endless reports of:
[ 5.058454] irq 13, desc: ffffffff80a7ad80, depth: 1, count: 0, unhandled: 0
[ 5.062057] ->handle_irq(): ffffffff801b1838,
[ 5.062175] handle_bad_irq+0x0/0x2c0
Where IRQ 13 is the UART interrupt.
To fix this, just remove the write to pcpu_masks in
gic_shared_irq_domain_map. The existing write in gic_unmask_irq is the
correct place for what is now the effective unmasking.
Cc: stable@vger.kernel.org
Fixes: 7778c4b27cbe ("irqchip: mips-gic: Use pcpu_masks to avoid reading GIC_SH_MASK*")
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
If the physical address of the GIC resource cannot be read from device
tree, then the code falls back to reading it from the gcr_gic_base
register. Hopefully this has been set to a sane value by the bootloader
or some platform code, but is defined by the hardware manual to have
"undefined" reset state. Using it as the address at which the GIC will
be mapped into physical memory space can therefore be risky if it has
not been initialised, since it may result in the GIC being mapped to an
effectively random address anywhere in physical memory, where it might
conflict with peripherals or RAM and lead to weird crashes.
Since a "sane value" is very platform specific because it is particular
to the platform's memory map, it is difficult to test for. At the very
least, a warning message should be printed in the case that we trust the
inherited value.
Reported-by: Amit Kama <amit.kama@satixfy.com>
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Several messages from the MIPS GIC driver include the text "GIC", but
the format is not standard. Add a pr_fmt of "irq-mips-gic: " and reword
the messages now that they will be prefixed with the driver name.
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
We have 2 bitmaps used to keep track of interrupts dedicated to IPIs in
the MIPS GIC irqchip driver. These bitmaps are only used from the one
compilation unit of that driver, and so can be made static. Do so in
order to avoid polluting the symbol table & global namespace.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The gic_set_type() function included writes to the MIPS GIC polarity,
trigger & dual-trigger registers in each case of a switch statement
determining the IRQs type. This is all well & good when we only have a
single cluster & thus a single GIC whose register we want to update. It
will lead to significant duplication once we have multi-cluster support
& multiple GICs to update.
Refactor this such that we determine values for the polarity, trigger &
dual-trigger registers and then have a single set of register writes
following the switch statement. This will allow us to write the same
values to each GIC in a multi-cluster system in a later patch, rather
than needing to duplicate more register writes in each case.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Following the past few patches nothing uses the gic_vpes variable any
longer. Remove the dead code.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Reserving a number of IPIs based upon the number of VPs reported by the
GIC makes little sense for a few reasons:
- The kernel may have been configured with NR_CPUS less than the number
of VPs in the cluster, in which case using gic_vpes causes us to
reserve more interrupts for IPIs than we will possibly use.
- If a kernel is configured without support for multi-threading & runs
on a system with multi-threading & multiple VPs per core then we'll
similarly reserve more interrupts for IPIs than we will possibly use.
- In systems with multiple clusters the GIC can only provide us with
the number of VPs in its cluster, not across all clusters. In this
case we'll reserve fewer interrupts for IPIs than we need.
Fix these issues by using num_possible_cpus() instead, which in all
cases is actually indicative of how many IPIs we may need.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Rather than configuring EIC mode for all CPUs during boot, configure it
locally on each when they come online. This will become important with
multi-cluster support, since clusters may be powered on & off (for
example via hotplug) and would lose the EIC configuration when powered
off.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
We currently walk through the range 0..gic_vpes-1, expecting these
values all to be valid Linux CPU numbers to provide to mips_cm_vp_id(),
and masking all routable local interrupts during boot. This approach has
a few drawbacks:
- In multi-cluster systems we won't have access to all CPU's GIC local
registers when the driver is probed, since clusters (and their GICs)
may be powered down at this point & only brought online later.
- In multi-cluster systems we may power down clusters at runtime, for
example if we offline all CPUs within it via hotplug, and the
cluster's GIC may lose state. We therefore need to reinitialise it
when powering back up, which this approach does not take into
account.
- The range 0..gic_vpes-1 may not all be valid Linux CPU numbers, for
example if we run a kernel configured to support fewer CPUs than the
system it is running on actually has. In this case we'll get garbage
values from mips_cm_vp_id() as we read past the end of the cpu_data
array.
Fix this and simplify the code somewhat by writing an all-bits-set
value to the VP-local reset mask register when a CPU is brought online,
before any local interrupts are configured for it. This removes the need
for us to access all CPUs during driver probe, removing all of the
problems described above.
In the name of simplicity we drop the checks for routability of
interrupts and simply clear the mask bits for all interrupts. Bits for
non-routable local interrupts will have no effect so there's no point
performing extra work to avoid modifying them.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The gic_all_vpes_local_irq_controller chip currently attempts to operate
on all CPUs/VPs in the system when masking or unmasking an interrupt.
This has a few drawbacks:
- In multi-cluster systems we may not always have access to all CPUs in
the system. When all CPUs in a cluster are powered down that
cluster's GIC may also power down, in which case we cannot configure
its state.
- Relatedly, if we power down a cluster after having configured
interrupts for CPUs within it then the cluster's GIC may lose state &
we need to reconfigure it. The current approach doesn't take this
into account.
- It's wasteful if we run Linux on fewer VPs than are present in the
system. For example if we run a uniprocessor kernel on CPU0 of a
system with 16 CPUs then there's no point in us configuring CPUs
1-15.
- The implementation is also lacking in that it expects the range
0..gic_vpes-1 to represent valid Linux CPU numbers which may not
always be the case - for example if we run on a system with more VPs
than the kernel is configured to support.
Fix all of these issues by only configuring the affected interrupts for
CPUs which are online at the time, and recording the configuration in a
new struct gic_all_vpes_chip_data for later use by CPUs being brought
online. We register a CPU hotplug state (reusing
CPUHP_AP_IRQ_GIC_STARTING which the ARM GIC driver uses, and which seems
suitably generic for reuse with the MIPS GIC) and execute
irq_cpu_online() in order to configure the interrupts on the newly
onlined CPU.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The gic_local_irq_domain_map() function has only one callsite in
gic_irq_domain_map(), and the split between the two functions makes it
unclear that they duplicate calculations & checks.
Inline gic_local_irq_domain_map() into gic_irq_domain_map() in order to
clean this up. Doing this makes the following small issues obvious, and
the patch tidies them up:
- Both functions used GIC_HWIRQ_TO_LOCAL() to convert a hwirq number to
a local IRQ number. We now only do this once. Although the compiler
ought to have optimised this away before anyway, the change leaves us
with less duplicate code.
- gic_local_irq_domain_map() had a check for invalid local interrupt
numbers (intr > GIC_LOCAL_INT_FDC). This condition can never occur
because any hwirq higher than those used for local interrupts is a
shared interrupt, which gic_irq_domain_map() already handles
separately. We therefore remove this check.
- The decision of whether to map the interrupt to gic_cpu_pin or
timer_cpu_pin can be handled within the existing switch statement in
gic_irq_domain_map(), shortening the code a little.
The change additionally prepares us nicely for the following patch of
the series which would otherwise need to duplicate the check for whether
a local interrupt should be percpu_devid or just percpu (ie. the switch
statement from gic_irq_domain_map()) in gic_local_irq_domain_map().
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Commit 7778c4b27cbe ("irqchip: mips-gic: Use pcpu_masks to avoid reading
GIC_SH_MASK*") adjusted the way we handle masking interrupts to set &
clear the interrupt's bit in each pcpu_mask. This allows us to avoid
needing to read the GIC mask registers and perform a bitwise and of
their values with the pending & pcpu_masks.
Unfortunately this didn't quite work for IPIs, which were mapped to a
particular CPU/VP during initialisation but never set the affinity or
effective_affinity fields of their struct irq_desc. This led to them
losing their affinity when gic_unmask_irq() was called for them, and
they'd all become affine to cpu0.
Fix this by:
1) Setting the effective affinity of interrupts in
gic_shared_irq_domain_map(), which is where we actually map an
interrupt to a CPU/VP. This ensures that the effective affinity mask
is always valid, not just after explicitly setting affinity.
2) Using an interrupt's effective affinity when unmasking it, which
prevents gic_unmask_irq() from unintentionally changing which
pcpu_mask includes an interrupt.
Fixes: 7778c4b27cbe ("irqchip: mips-gic: Use pcpu_masks to avoid reading GIC_SH_MASK*")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: https://lkml.kernel.org/r/20170922062440.23701-3-paul.burton@imgtec.com
|
|
The MIPS GIC driver is incorrectly using __fls to shift registers,
intending to shift to the least significant bit of a value based upon
its mask but instead shifting off all but the value's top bit. It should
actually be using __ffs to shift to the first, not last, bit of the
value.
Apparently the system I used when testing commit 3680746abd87
("irqchip: mips-gic: Convert remaining shared reg access to new
accessors") and commit b2b2e584ceab ("irqchip: mips-gic: Clean up mti,
reserved-cpu-vectors handling") managed to work correctly despite this
issue, but not all systems do...
Fixes: 3680746abd87 ("irqchip: mips-gic: Convert remaining shared reg access to new accessors")
Fixes: b2b2e584ceab ("irqchip: mips-gic: Clean up mti, reserved-cpu-vectors handling")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: https://lkml.kernel.org/r/20170922062440.23701-2-paul.burton@imgtec.com
|
|
The write_gic_smask() & write_gic_rmask() functions take a shared
interrupt number as a parameter, but we're incorrectly providing them a
bitmask with the shared interrupt's bit set. This effectively means that
we mask or unmask the shared interrupt 1<<n rather than shared interrupt
n, and as a result likely drop interrupts.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 68898c8765f4 ("irqchip: mips-gic: Drop gic_(re)set_mask() functions")
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.14 for MIPS; below a summary of
the non-merge commits:
CM:
- Rename mips_cm_base to mips_gcr_base
- Specify register size when generating accessors
- Use BIT/GENMASK for register fields, order & drop shifts
- Add cluster & block args to mips_cm_lock_other()
CPC:
- Use common CPS accessor generation macros
- Use BIT/GENMASK for register fields, order & drop shifts
- Introduce register modify (set/clear/change) accessors
- Use change_*, set_* & clear_* where appropriate
- Add CM/CPC 3.5 register definitions
- Use GlobalNumber macros rather than magic numbers
- Have asm/mips-cps.h include CM & CPC headers
- Cluster support for topology functions
- Detect CPUs in secondary clusters
CPS:
- Read GIC_VL_IDENT directly, not via irqchip driver
DMA:
- Consolidate coherent and non-coherent dma_alloc code
- Don't use dma_cache_sync to implement fd_cacheflush
FPU emulation / FP assist code:
- Another series of 14 commits fixing corner cases such as NaN
propgagation and other special input values.
- Zero bits 32-63 of the result for a CLASS.D instruction.
- Enhanced statics via debugfs
- Do not use bools for arithmetic. GCC 7.1 moans about this.
- Correct user fault_addr type
Generic MIPS:
- Enhancement of stack backtraces
- Cleanup from non-existing options
- Handle non word sized instructions when examining frame
- Fix detection and decoding of ADDIUSP instruction
- Fix decoding of SWSP16 instruction
- Refactor handling of stack pointer in get_frame_info
- Remove unreachable code from force_fcr31_sig()
- Convert to using %pOF instead of full_name
- Remove the R6000 support.
- Move FP code from *_switch.S to *_fpu.S
- Remove unused ST_OFF from r2300_switch.S
- Allow platform to specify multiple its.S files
- Add #includes to various files to ensure code builds reliable and
without warning..
- Remove __invalidate_kernel_vmap_range
- Remove plat_timer_setup
- Declare various variables & functions static
- Abstract CPU core & VP(E) ID access through accessor functions
- Store core & VP IDs in GlobalNumber-style variable
- Unify checks for sibling CPUs
- Add CPU cluster number accessors
- Prevent direct use of generic_defconfig
- Make CONFIG_MIPS_MT_SMP default y
- Add __ioread64_copy
- Remove unnecessary inclusions of linux/irqchip/mips-gic.h
GIC:
- Introduce asm/mips-gic.h with accessor functions
- Use new GIC accessor functions in mips-gic-timer
- Remove counter access functions from irq-mips-gic.c
- Remove gic_read_local_vp_id() from irq-mips-gic.c
- Simplify shared interrupt pending/mask reads in irq-mips-gic.c
- Simplify gic_local_irq_domain_map() in irq-mips-gic.c
- Drop gic_(re)set_mask() functions in irq-mips-gic.c
- Remove gic_set_polarity(), gic_set_trigger(), gic_set_dual_edge(),
gic_map_to_pin() and gic_map_to_vpe() from irq-mips-gic.c.
- Convert remaining shared reg access, local int mask access and
remaining local reg access to new accessors
- Move GIC_LOCAL_INT_* to asm/mips-gic.h
- Remove GIC_CPU_INT* macros from irq-mips-gic.c
- Move various definitions to the driver
- Remove gic_get_usm_range()
- Remove __gic_irq_dispatch() forward declaration
- Remove gic_init()
- Use mips_gic_present() in place of gic_present and remove
gic_present
- Move gic_get_c0_*_int() to asm/mips-gic.h
- Remove linux/irqchip/mips-gic.h
- Inline __gic_init()
- Inline gic_basic_init()
- Make pcpu_masks a per-cpu variable
- Use pcpu_masks to avoid reading GIC_SH_MASK*
- Clean up mti, reserved-cpu-vectors handling
- Use cpumask_first_and() in gic_set_affinity()
- Let the core set struct irq_common_data affinity
microMIPS:
- Fix microMIPS stack unwinding on big endian systems
MIPS-GIC:
- SYNC after enabling GIC region
NUMA:
- Remove the unused parent_node() macro
R6:
- Constify r2_decoder_tables
- Add accessor & bit definitions for GlobalNumber
SMP:
- Constify smp ops
- Allow boot_secondary SMP op to return errors
VDSO:
- Drop gic_get_usm_range() usage
- Avoid use of linux/irqchip/mips-gic.h
Platform changes:
Alchemy:
- Add devboard machine type to cpuinfo
- update cpu feature overrides
- Threaded carddetect irqs for devboards
AR7:
- allow NULL clock for clk_get_rate
BCM63xx:
- Fix ENETDMA_6345_MAXBURST_REG offset
- Allow NULL clock for clk_get_rate
CI20:
- Enable GPIO and RTC drivers in defconfig
- Add ethernet and fixed-regulator nodes to DTS
Generic platform:
- Move Boston and NI 169445 FIT image source to their own files
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Allow filtering enabled boards by requirements
- Don't explicitly disable CONFIG_USB_SUPPORT
- Bump default NR_CPUS to 16
JZ4700:
- Probe the jz4740-rtc driver from devicetree
Lantiq:
- Drop check of boot select from the spi-falcon driver.
- Drop check of boot select from the lantiq-flash MTD driver.
- Access boot cause register in the watchdog driver through regmap
- Add device tree binding documentation for the watchdog driver
- Add docs for the RCU DT bindings.
- Convert the fpi bus driver to a platform_driver
- Remove ltq_reset_cause() and ltq_boot_select(
- Switch to a proper reset driver
- Switch to a new drivers/soc GPHY driver
- Add an USB PHY driver for the Lantiq SoCs using the RCU module
- Use of_platform_default_populate instead of __dt_register_buses
- Enable MFD_SYSCON to be able to use it for the RCU MFD
- Replace ltq_boot_select() with dummy implementation.
Loongson 2F:
- Allow NULL clock for clk_get_rate
Malta:
- Use new GIC accessor functions
NI 169445:
- Add support for NI 169445 board.
- Only include in 32r2el kernels
Octeon:
- Add support for watchdog of 78XX SOCs.
- Add support for watchdog of CN68XX SOCs.
- Expose support for mips32r1, mips32r2 and mips64r1
- Enable more drivers in config file
- Add support for accessing the boot vector.
- Remove old boot vector code from watchdog driver
- Define watchdog registers for 70xx, 73xx, 78xx, F75xx.
- Make CSR functions node aware.
- Allow access to CIU3 IRQ domains.
- Misc cleanups in the watchdog driver
Omega2+:
- New board, add support and defconfig
Pistachio:
- Enable Root FS on NFS in defconfig
Ralink:
- Add Mediatek MT7628A SoC
- Allow NULL clock for clk_get_rate
- Explicitly request exclusive reset control in the pci-mt7620 PCI driver.
SEAD3:
- Only include in 32 bit kernels by default
VoCore:
- Add VoCore as a vendor t0 dt-bindings
- Add defconfig file"
* '4.14-features' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (167 commits)
MIPS: Refactor handling of stack pointer in get_frame_info
MIPS: Stacktrace: Fix microMIPS stack unwinding on big endian systems
MIPS: microMIPS: Fix decoding of swsp16 instruction
MIPS: microMIPS: Fix decoding of addiusp instruction
MIPS: microMIPS: Fix detection of addiusp instruction
MIPS: Handle non word sized instructions when examining frame
MIPS: ralink: allow NULL clock for clk_get_rate
MIPS: Loongson 2F: allow NULL clock for clk_get_rate
MIPS: BCM63XX: allow NULL clock for clk_get_rate
MIPS: AR7: allow NULL clock for clk_get_rate
MIPS: BCM63XX: fix ENETDMA_6345_MAXBURST_REG offset
mips: Save all registers when saving the frame
MIPS: Add DWARF unwinding to assembly
MIPS: Make SAVE_SOME more standard
MIPS: Fix issues in backtraces
MIPS: jz4780: DTS: Probe the jz4740-rtc driver from devicetree
MIPS: Ci20: Enable RTC driver
watchdog: octeon-wdt: Add support for 78XX SOCs.
watchdog: octeon-wdt: Add support for cn68XX SOCs.
watchdog: octeon-wdt: File cleaning.
...
|
|
Pull irq updates from Thomas Gleixner:
"The interrupt subsystem delivers this time:
- Refactoring of the GIC-V3 driver to prepare for the GIC-V4 support
- Initial GIC-V4 support
- Consolidation of the FSL MSI support
- Utilize the effective affinity interface in various ARM irqchip
drivers
- Yet another interrupt chip driver (UniPhier AIDET)
- Bulk conversion of the irq chip driver to use %pOF
- The usual small fixes and improvements all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (77 commits)
irqchip/ls-scfg-msi: Add MSI affinity support
irqchip/ls-scfg-msi: Add LS1043a v1.1 MSI support
irqchip/ls-scfg-msi: Add LS1046a MSI support
arm64: dts: ls1046a: Add MSI dts node
arm64: dts: ls1043a: Share all MSIs
arm: dts: ls1021a: Share all MSIs
arm64: dts: ls1043a: Fix typo of MSI compatible string
arm: dts: ls1021a: Fix typo of MSI compatible string
irqchip/ls-scfg-msi: Fix typo of MSI compatible strings
irqchip/irq-bcm7120-l2: Use correct I/O accessors for irq_fwd_mask
irqchip/mmp: Make mmp_intc_conf const
irqchip/gic: Make irq_chip const
irqchip/gic-v3: Advertise GICv4 support to KVM
irqchip/gic-v4: Enable low-level GICv4 operations
irqchip/gic-v4: Add some basic documentation
irqchip/gic-v4: Add VLPI configuration interface
irqchip/gic-v4: Add VPE command interface
irqchip/gic-v4: Add per-VM VPE domain creation
irqchip/gic-v3-its: Set implementation defined bit to enable VLPIs
irqchip/gic-v3-its: Allow doorbell interrupts to be injected/cleared
...
|
|
gic_set_affinity() manually copies the provided cpumask to the struct
irq_common_data affinity field, returning IRQ_SET_MASK_OK_NOCOPY in
order to prevent the core code from doing that.
We can instead simply let the core code do it for us, by returning
IRQ_SET_MASK_OK instead of IRQ_SET_MASK_OK_NOCOPY & doing the copy
ourselves.
[ralf@linux-mips.org: Resolve merge conflict.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17056/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Currently in gic_set_affinity() we calculate a temporary cpumask holding
the intersection of the provided cpumask & the CPUs that are online,
then we call cpumask_first twice on it to find the first such CPU. Since
we don't need the temporary cpumask for anything else & we only care
about the first CPU that's both online & in the provided cpumask, we can
instead use cpumask_first_and to find that CPU & drop the temporary
mask.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17110/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
When parsing mti,reserved-cpu-vectors we generate a mask of all bits
that have been declared reserved, the loop through starting from bit 2
to find one that isn't reserved (ie. is zero).
This patch accomplishes the same task more simply by:
- Inititialising the reserved mask to 0x3 (ie. the 2 software
interrupts). This means we don't need to skip them later as the loop
previously has.
- Replacing the loop checking for zero bits with find_first_zero_bit,
which fits our needs now that the 2 software interrupts are marked
reserved. This requires that the type of reserved is changed to
unsigned long so that it's suitable for use with bitmap functions.
- Replacing the magic number 8 with the hamming weight of the ST0_IM
field - ie. the number of bits that a MIPS CPU has for interrupt
inputs. This is still a compile-time constant 8, but makes it
clearer why it's 8.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17054/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This patch avoids the need to read the GIC_SH_MASK* registers when
decoding shared interrupts by setting & clearing the interrupt's bit in
the appropriate CPU's pcpu_masks entry when masking or unmasking the
interrupt.
This effectively means that whilst an interrupt is masked we clear its
bit in all pcpu_masks, which causes gic_handle_shared_int() to ignore it
on all CPUs without needing to check GIC_SH_MASK*.
In essence, we add a little overhead to masking or unmasking interrupts
but in return reduce the overhead of the far more common task of
decoding interrupts.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17109/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Define the pcpu_masks variable using the kernel's standard per-cpu
variable support, rather than an open-coded array of structs containing
bitmaps.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17052/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
gic_basic_init() is now a fairly short function that is only called in
one place. Inline it into gic_of_init() to help readability.
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17051/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The __gic_init() function is only called from gic_of_init() now that the
non-DT path has been removed. In order to simplify the code & aid
readability, fold __gic_init() into gic_of_init().
This provides us with the ability to return an error code, which
__gic_init() was previously unable to do. As such the irq_domain_add_*()
error paths are modified to print & return an error rather than panic().
[ralf@linux-mips.org: Resoled reject.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17050/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The linux/irqchip/mips-gic.h header is now almost empty. Move the
declarations of gic_get_c0_compare_int(), gic_get_c0_perfcount_int() &
gic_get_c0_fdc_int() to asm/mips-gic.h in order to close in on being
able to delete the former header.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17046/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Nothing uses the global gic_present variable anymore; mips_gic_present()
should be used instead. Remove the dead code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17045/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
All in-tree platforms now probe the GIC driver using device tree, and as
such nothing calls gic_init() any longer. Remove the dead code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17043/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
We provide a forward declaration of the __gic_irq_dispatch() function
for no apparent reason. Remove it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17042/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The MIPS VDSO code is no longer reliant upon the irqchip driver to
provide the address of the GIC's user-visible section via
gic_get_usm_range(). Remove the now-dead code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17041/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Move the definitions of macros used to convert between hardware IRQ
numbers & shared or local interrupt numbers into the irqchip driver,
which is all that should ever need to care about them.
Remove GIC_CPU_TO_VEC_OFFSET() in the process since it's never used.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17039/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Convert the remaining accesses to registers in the GIC VP-local &
VP-other register blocks to use the new accessor functions provided by
asm/mips-gic.h, resulting in code which is often shorter & easier to
read.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17036/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Use the new accessor functions provided by asm/mips-gic.h to access
masks controlling local interrupts, resulting in code which is often
shorter & easier to read.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17035/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Convert the remaining accesses to registers in the GIC shared register
block to use the new accessor functions provided by asm/mips-gic.h,
resulting in code which is often shorter & easier to read.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17034/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Remove the gic_map_to_vpe() function in favour of using the new
write_gic_map_vp() accessor function which isn't any more complex to
use & allows us to drop a level of abstraction.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17033/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Remove the gic_map_to_pin() function in favour of using the new
write_gic_map_pin() accessor function which isn't any more complex to
use & allows us to drop a level of abstraction.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17032/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Remove the gic_set_dual_edge() function in favour of using the new
change_gic_dual() accessor function which provides equivalent
functionality. This also allows us to remove the gic_update_bits()
function which gic_set_dual_edge() was the last user of, along with the
GIC_INTR_OFS() & GIC_INTR_BIT() macros.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17031/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Remove the gic_set_trigger() function in favour of using the new
change_gic_trig() accessor function which provides equivalent
functionality.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17030/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Remove the gic_set_polarity() function in favour of using the new
change_gic_pol() accessor function which provides equivalent
functionality.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17029/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The gic_set_mask() & gic_reset_mask() functions are now no more
convenient to call than the write_gic_smask() or write_gic_rmask()
accessor functions. Remove the layer of abstraction.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17028/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Simplify gic_local_irq_domain_map() by:
- Moving the check for invalid IRQs outside of the loop.
- Moving the decision about whether to use gic_cpu_pin or timer_cpu_pin
outside of the loop.
- Using the new write_gic_vo_map() accessor function to avoid the need
to handle each map register separately.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17027/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Simplify the reads of the bitmaps indicating pending & masked interrupts
in gic_handle_shared_int() using the __ioread32_copy() &
__ioread64_copy() helper functions.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17026/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Nothing needs gic_read_local_vp_id() any longer, so remove the dead
code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17024/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The MIPS GIC clocksource driver is no longer using the accessor
functions provided by the irqchip driver, so remove them.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17022/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This patch introduces a new header providing accessor functions for the
MIPS Global Interrupt Controller (GIC) mirroring those provided for the
other 2 components of the MIPS Coherent Processing System (CPS) - the
Coherence Manager (CM) & Cluster Power Controller (CPC).
This header makes use of the new standardised CPS accessor macros where
possible, but does require some custom accessors for cases where we have
either a bit or a register per interrupt.
A major advantage of this over the existing
include/linux/irqchip/mips-gic.h definitions is that code performing
accesses can become much simpler, for example this:
gic_update_bits(GIC_REG(SHARED, GIC_SH_SET_TRIGGER) +
GIC_INTR_OFS(intr), 1ul << GIC_INTR_BIT(intr),
(unsigned long)trig << GIC_INTR_BIT(intr));
...can become simply:
change_gic_trig(intr, trig);
The accessors handle 32 vs 64 bit in the same way as for CM & CPC code,
which means that GIC code will also not need to worry about the access
size in most cases. They are also accessible outside of
drivers/irqchip/irq-mips-gic.c which will allow for simplification in
the use of the non-interrupt portions of the GIC (eg. counters) which
currently require the interrupt controller driver to expose helper
functions for access.
This patch doesn't change any existing code over to use the new
accessors yet, since a wholesale change would be invasive & difficult to
review. Instead follow-on patches will convert code piecemeal to use
this new header. The one change to existing code is to rename gic_base
to mips_gic_base & make it global, in order to fit in with the naming
expected by the standardised CPS accessor macros.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17020/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
A SYNC is required between enabling the GIC region and actually trying
to use it, even if the first access is a read, otherwise its possible
depending on the timing (and in my case depending on the precise
alignment of certain kernel code) to hit CM bus errors on that first
access.
Add the SYNC straight after setting the GIC base.
[paul.burton@imgtec.com:
Changes later in this series increase our likelihood of hitting this
by reducing the amount of code that runs between enabling the GIC &
accessing it.]
Fixes: a7057270c280 ("irqchip: mips-gic: Add device-tree support")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17019/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
A SYNC is required between enabling the GIC region and actually trying
to use it, even if the first access is a read, otherwise its possible
depending on the timing (and in my case depending on the precise
alignment of certain kernel code) to hit CM bus errors on that first
access.
Add the SYNC straight after setting the GIC base.
[paul.burton@imgtec.com:
Changes later in this series increase our likelihood of hitting this
by reducing the amount of code that runs between enabling the GIC &
accessing it.]
Fixes: a7057270c280 ("irqchip: mips-gic: Add device-tree support")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.19.x-
Patchwork: https://patchwork.linux-mips.org/patch/17019/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
With Coherence Manager (CM) 3.5 information about the topology of the
system, which has previously only been available through & accessed from
the CM, is now also provided by the Cluster Power Controller (CPC). This
includes a new CPC_CONFIG register mirroring GCR_CONFIG, and similarly a
new CPC_Cx_CONFIG register mirroring GCR_Cx_CONFIG.
In preparation for adjusting functions such as mips_cm_numcores(), which
have previously only needed to access the CM, to also access the CPC
this patch modifies the way we use the various CPS headers. Rather than
having users include asm/mips-cm.h or asm/mips-cpc.h individually we
instead have users include asm/mips-cps.h which in turn includes
asm/mips-cm.h & asm/mips-cpc.h. This means that users will gain access
to both CM & CPC registers by including one header, and most importantly
it makes asm/mips-cps.h an ideal location for helper functions which
need to access the various components of the CPS.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17015/
Patchwork: https://patchwork.linux-mips.org/patch/17217/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
There's no reason for us not to use BIT() & GENMASK() in asm/mips-cm.h
when declaring macros corresponding to register fields. This patch
modifies our definitions to do so.
The *_SHF definitions are removed entirely - they duplicate information
found in the masks, are infrequently used & can be replaced with use of
__ffs() where needed.
The *_MSK definitions then lose their _MSK suffix which is now somewhat
redundant, and users are modified to match.
The field definitions are moved to follow the appropriate register's
accessor functions, which helps to keep the field definitions in order &
to find the appropriate fields for a given register. Whilst here a
comment is added describing each register & including its name, which is
helpful both for linking the register back to hardware documentation &
for grepping purposes.
This also cleans up a couple of issues that became obvious as a result
of making the changes described above:
- We previously had definitions for GCR_Cx_RESET_EXT_BASE & a phony
copy of that named GCR_RESET_EXT_BASE - a register which does not
exist. The bad definitions were added by commit 497e803ebf98 ("MIPS:
smp-cps: Ensure secondary cores start with EVA disabled") and made
use of from boot_core(), which is now modified to use the
GCR_Cx_RESET_EXT_BASE definitions.
- We had a typo in CM_GCR_ERROR_CAUSE_ERRINGO_MSK - we now correctly
define this as inFo rather than inGo.
Now that we don't duplicate field information between _SHF & _MSK
definitions, and keep the fields next to the register accessors, it will
be much easier to spot & prevent any similar oddities being introduced
in the future.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17001/
Patchwork: https://patchwork.linux-mips.org/patch/17216/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The MIPS GIC driver only targets a single CPU at a time, even if
the notional affinity is wider. Let's inform the core code
about this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-12-marc.zyngier@arm.com
|
|
Since commit d59f6617eef0f ("genirq: Allow fwnode to carry name
information only") the irqdomain core sets the names of irq domains.
When the name is allocated the new IRQ_DOMAIN_NAME_ALLOCATED flag is
set. Replacing the allocated name with a constant one is not a good
idea, since calling the new irq_domain_update_bus_token() API, added to
the MIPS GIC driver by commit 96f0d93a487e1 ("irqchip/MSI: Use
irq_domain_update_bus_token instead of an open coded access") will
attempt to kfree the pointer, and result in a kernel OOPS.
Fix this by removing the names, now that they are set by the irqdomain
core. This effectively reverts commit 21c57fd13589 ("irqchip/mips-gic:
Populate irq_domain names").
Fixes: d59f6617eef0f ("genirq: Allow fwnode to carry name information only")
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1500363561-32213-1-git-send-email-matt.redfearn@imgtec.com
|
Paul Burton
Matt Redfearn
Paul Burton
Linus Torvalds
James Hogan
Marc Zyngier
Matt Redfearn