| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
For SSD, if request size exceeds specific value (optimal io size), request size
isn't important for bandwidth. In such condition, if making request size bigger
will cause some disks idle, the total throughput will actually drop. A good
example is doing a readahead in a two-disk raid1 setup.
So when should we split big requests? We absolutly don't want to split big
request to very small requests. Even in SSD, big request transfer is more
efficient. This patch only considers request with size above optimal io size.
If all disks are busy, is it worth doing a split? Say optimal io size is 16k,
two requests 32k and two disks. We can let each disk run one 32k request, or
split the requests to 4 16k requests and each disk runs two. It's hard to say
which case is better, depending on hardware.
So only consider case where there are idle disks. For readahead, split is
always better in this case. And in my test, below patch can improve > 30%
thoughput. Hmm, not 100%, because disk isn't 100% busy.
Such case can happen not just in readahead, for example, in directio. But I
suppose directio usually will have bigger IO depth and make all disks busy, so
I ignored it.
Note: if the raid uses any hard disk, we don't prevent merging. That will make
performace worse.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Currently the sequential read detection is global wide. It's natural to make it
per disk based, which can improve the detection for concurrent multiple
sequential reads. And next patch will make SSD read balance not use distance
based algorithm, where this change help detect truly sequential read for SSD.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
MD RAID1/RAID10: Move some macros from .h file to .c file
There are three macros (IO_BLOCKED,IO_MADE_GOOD,BIO_SPECIAL) which are defined
in both raid1.h and raid10.h. They are only used in there respective .c files.
However, if we wish to make RAID10 accessible to the device-mapper RAID
target (dm-raid.c), then we need to move these macros into the .c files where
they are used so that they do not conflict with each other.
The macros from the two files are identical and could be moved into md.h, but
I chose to leave the duplication and have them remain in the personality
files.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
MD RAID1: Rename the structure 'mirror_info' to 'raid1_info'
The same structure name ('mirror_info') is used by raid10. Each of these
structures are defined in there respective header files. If dm-raid is
to support both RAID1 and RAID10, the header files will be included and
the structure names must not collide. While only one of these structure
names needs to change, this patch adds consistency to the naming of the
structure.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
In RAID1, a replacement is much like a normal device, so we just
double the size of the relevant arrays and look at all possible
devices for reads and writes.
This means that the array looks like it is now double the size in some
way - we need to be careful about that.
In particular, we checking if the array is still degraded while
creating a recovery request we need to only consider the first 'half'
- i.e. the real (non-replacement) devices.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
RAID1 and RAID10 handle write requests by queuing them for handling by
a separate thread. This is because when a write-intent-bitmap is
active we might need to update the bitmap first, so it is good to
queue a lot of writes, then do one big bitmap update for them all.
However writeback request devices to appear to be congested after a
while so it can make some guesstimate of throughput. The infinite
queue defeats that (note that RAID5 has already has a finite queue so
it doesn't suffer from this problem).
So impose a limit on the number of pending write requests. By default
it is 1024 which seems to be generally suitable. Make it configurable
via module option just in case someone finds a regression.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Having mddev_t and 'struct mddev_s' is ugly and not preferred
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
The typedefs are just annoying. 'mdk' probably refers to 'md_k.h'
which used to be an include file that defined this thing.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
There wasn't much and it is inconsistent.
Also rearrange fields to keep related fields together.
Reported-by: Aapo Laine <aapo.laine@shiftmail.org>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
When we get a write error (in the data area, not in metadata),
update the badblock log rather than failing the whole device.
As the write may well be many blocks, we trying writing each
block individually and only log the ones which fail.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
|
|
When performing write-behind we allocate pages to store the data
during write.
Previously we just keep a list of pages. Now we keep a list of
bi_vec which includes offset and size.
This means that the r1bio has complete information to create a new
bio which will be needed for retrying after write errors.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
|
|
If we succeed in writing to a block that was recorded as
being bad, we clear the bad-block record.
This requires some delayed handling as the bad-block-list update has
to happen in process-context.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
|
|
Now that we have a bad block list, we should not read from those
blocks.
There are several main parts to this:
1/ read_balance needs to check for bad blocks, and return not only
the chosen device, but also how many good blocks are available
there.
2/ fix_read_error needs to avoid trying to read from bad blocks.
3/ read submission must be ready to issue multiple reads to
different devices as different bad blocks on different devices
could mean that a single large read cannot be served by any one
device, but can still be served by the array.
This requires keeping count of the number of outstanding requests
per bio. This count is stored in 'bi_phys_segments'
4/ retrying a read needs to also be ready to submit a smaller read
and queue another request for the rest.
This does not yet handle bad blocks when reading to perform resync,
recovery, or check.
'md_trim_bio' will also be used for RAID10, so put it in md.c and
export it.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
If we hit a read error while recovering a mirror, we want to abort the
recovery without necessarily failing the disk - as having a disk this
a read error is better than not having an array at all.
Currently this is managed with a per-array flag "recovery_disabled"
and is only implemented for RAID1. For RAID10 we will need finer
grained control as we might want to disable recovery for individual
devices separately.
So push more of the decision making into the personality.
'recovery_disabled' is now a 'cookie' which is copied when the
personality want to disable recovery and is changed when a device is
added to the array as this is used as a trigger to 'try recovery
again'.
This will allow RAID10 to get the control that it needs.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
MD RAID1: Changes to allow RAID1 to be used by device-mapper (dm-raid.c)
Added the necessary congestion function and conditionalize calls requiring an
array 'queue' or 'gendisk'.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
The current handling and freeing of these pages is a bit fragile.
We only keep the list of allocated pages in each bio, so we need to
still have a valid bio when freeing the pages, which is a bit clumsy.
So simply store the allocated page list in the r1_bio so it can easily
be found and freed when we are finished with the r1_bio.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
This structure field (flushing_bio_list) is never used, so remove it.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
This patch converts md to support REQ_FLUSH/FUA instead of now
deprecated REQ_HARDBARRIER. In the core part (md.c), the following
changes are notable.
* Unlike REQ_HARDBARRIER, REQ_FLUSH/FUA don't interfere with
processing of other requests and thus there is no reason to mark the
queue congested while FLUSH/FUA is in progress.
* REQ_FLUSH/FUA failures are final and its users don't need retry
logic. Retry logic is removed.
* Preflush needs to be issued to all member devices but FUA writes can
be handled the same way as other writes - their processing can be
deferred to request_queue of member devices. md_barrier_request()
is renamed to md_flush_request() and simplified accordingly.
For linear, raid0 and multipath, the core changes are enough. raid1,
5 and 10 need the following conversions.
* raid1: Handling of FLUSH/FUA bio's can simply be deferred to
request_queues of member devices. Barrier related logic removed.
* raid5: Queue draining logic dropped. FUA bit is propagated through
biodrain and stripe resconstruction such that all the updated parts
of the stripe are written out with FUA writes if any of the dirtying
writes was FUA. preread_active_stripes handling in make_request()
is updated as suggested by Neil Brown.
* raid10: FUA bit needs to be propagated to write clones.
linear, raid0, 1, 5 and 10 tested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Neil Brown <neilb@suse.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
A 2-device raid5 array can now be converted to raid1.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Having a macro just to cast a void* isn't really helpful.
I would must rather see that we are simply de-referencing ->private,
than have to know what the macro does.
So open code the macro everywhere and remove the pointless cast.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
This makes the includes more explicit, and is preparation for moving
md_k.h to drivers/md/md.h
Remove include/raid/md.h as its only remaining use was to #include
other files.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Move the headers with the local structures for the disciplines and
bitmap.h into drivers/md/ so that they are more easily grepable for
hacking and not far away. md.h is left where it is for now as there
are some uses from the outside.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: NeilBrown <neilb@suse.de>
|
Shaohua Li
Jonathan Brassow
NeilBrown
Tejun Heo
Christoph Hellwig