| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Afterwards it is possible to convert attaching in card drivers.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
When si2165_init fails, the clk values in state are still at zero.
But the dvb-core ignores the return value of init will call tune
afterwards.
This will trigger a division by zero when tuning.
At least check for the variables to be non-zero before dividing.
This happened for a system with WinTV HVR-4400 PCIe-card after suspend-to-disk.
Do suspend-to-disk without accessing the DVB device before.
After wakeup try to tune.
si2165_init fails at checking the chip_mode and aborts.
Then si2165_set_if_freq_shift will fail with div-by-zero.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
inside lgdt3306a_search we reading demod status 20 times with 50 msec sleep after each read.
This gives us more than 1 sec of delay. Removing this delay should not affect demod functionality.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Acked-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
if specified DVB-C bandwidth not supported then force 8MHz.
Should work for most cases.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Added function to read BER for ISDB-T
Also SNR values fixed for ISDB-T
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
ensure multiple separate register reads are from the same snapshot
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Use regmap for I2C register access.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Check demod and ts locks and report lock status according to those.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Use correct device for logging functions as we now have it due to
proper I2C client bindings.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Add I2C driver bindings in order to support proper I2C driver
registration with driver core.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Return DVBv5 statistics via legacy DVBv3 API.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Implement dvbv5 statistics for DVB-C.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Implement dvbv5 statistics for DVB-T2.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Implement dvbv5 statistics for DVB-T.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Use 64-bit calculation.
Return error if tuner does not provide get_if_frequency() callback.
All currently used tuners has it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Trivial fix to spelling mistake in pr_warn message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
These structures are only used to copy into other structures, so declare
them as const.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct dvb_tuner_ops i@p = { ... };
@ok1@
identifier r.i;
expression e;
position p;
@@
e = i@p
@ok2@
identifier r.i;
expression e1, e2;
position p;
@@
memcpy(e1, &i@p, e2)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct dvb_tuner_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct dvb_tuner_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
With the current settings, only one channel locks properly.
That's likely because, when this driver was written, Brazil
were still using experimental transmissions.
Change it to reproduce the settings used by the newer drivers.
That makes it lock on other channels.
Tested with both PixelView SBTVD Hybrid (cx231xx-based) and
C3Tech Digital Duo HDTV/SDTV (em28xx-based) devices.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
On this frontend, it takes a while to start output normal
TS data. That only happens on state S9. On S8, the TS output
is enabled, but it is not reliable enough.
However, the zigzag loop is too fast to let it sync.
As, on practical tests, the zigzag software loop doesn't
seem to be helping, but just slowing down the tuning, let's
switch to hardware algorithm, as the tuners used on such
devices are capable of work with frequency drifts without
any help from software.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The error return path of failed calls to heleno_x_pon leak
memory because priv is not kfree'd. Fix this by kfree'ing
priv before returning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
It is likely that checking the result of the 2nd 'read16' is expected here.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The addition of jump label support in dynamic_debug caused an unexpected
warning in exactly one file in the kernel:
drivers/media/dvb-frontends/cxd2841er.c: In function 'cxd2841er_tune_tc':
include/linux/dynamic_debug.h:134:3: error: 'carrier_offset' may be used uninitialized in this function [-Werror=maybe-uninitialized]
__dynamic_dev_dbg(&descriptor, dev, fmt, \
^~~~~~~~~~~~~~~~~
drivers/media/dvb-frontends/cxd2841er.c:3177:11: note: 'carrier_offset' was declared here
int ret, carrier_offset;
^~~~~~~~~~~~~~
The problem seems to be that the compiler gets confused by the extra
conditionals in static_branch_unlikely, to the point where it can no
longer keep track of which branches have already been taken, and it
doesn't realize that this variable is now always initialized when it
gets used.
I have done lots of randconfig kernel builds and could not find any
other file with this behavior, so I assume it's a rare enough glitch
that we don't need to change the jump label support but instead just
work around the warning in the driver.
To achieve that, I'm moving the check for the return value into the
switch() statement, which is an obvious transformation, but is enough to
un-confuse the compiler here. The resulting code is not as nice to
read, but at least we retain the behavior of warning if it gets changed
to actually access an uninitialized carrier offset value in the future.
Link: http://lkml.kernel.org/r/20160713204342.1221511-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Abylay Ospan <aospan@netup.ru>
Cc: Sergey Kozlov <serjk@netup.ru>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Jason Baron <jbaron@akamai.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Now driver returns correct values for DVB-C:
SNR (in dB)
[mchehab@s-opensource.com: fix a new function to be static]
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
now driver returns correct values for DVB-C:
BER (post_bit_count and post_bit_error values)
UCB (count of uncorrected errors)
also, some code cleanup was done - checkpatch.pl now is happy
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
DVB-C should use cxd2841er_read_agc_gain_c() to get the gain. The same
function is used for all DVB-C annex delivery systems.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The scale for ISDB-T was wrong too: it was inverted, and
on a relative scale.
Use a linear interpolation to make it look better.
The formula was empirically determined, using 3 frequencies
(175 MHz, 410 MHz and 800 MHz), measuring from -50dBm to
-12dBm in steps of 0.5dB.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Instead of using a relative frequency range, calibrate it to
show the results in dB. The callibration was done getting
samples with a signal generated from -50dBm to -12dBm,
incremented in steps of 0.5 dB, using 3 frequencies:
175 MHz, 410 MHz and 800 MHz. The modulated signal was
using QAM64, and it was used a linear interpolation of all
the results.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Currently, there's no stats for DVB-C. Let's at least return
signal strength. The scale is different than on DVB-T, so let's
use a relative scale, for now.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
What userspace expects is to receive both bit_error and bit_count
counters. So, instead of doing the division at the Kernel,
return the counters for userspace to handle it the way it
wants.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Appling the mask 0x0f to the immediate return of the call to
mb86a20s_readreg will always result in a positive value, meaning that the
check of ret < 0 will never work. Instead, check for a -ve return value
first, and then mask val with 0x0f.
Kudos to Mauro Carvalho Chehab for spotting the mistake in my original fix.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Tuning a card with Sony ASCOT2E produces the following error:
kernel: i2c i2c-9: wr reg=0006: len=11 is too big!
MAX_WRITE_REGSIZE is defined as 10, buf[MAX_WRITE_REGSIZE + 1] buffer is
used in ascot2e_write_regs().
The problem is that exactly 10 bytes are written in ascot2e_set_params():
/* Set BW_OFFSET (0x0F) value from parameter table */
data[9] = ascot2e_sett[tv_system].bw_offset;
ascot2e_write_regs(priv, 0x06, data, 10);
The test in write_regs is as follows:
if (len + 1 >= sizeof(buf))
10 + 1 = 11 and that would be exactly the size of buf. Since 10 bytes +
buf[0] = reg would seem to fit into buf[], this shouldn't be an error.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Fix two warnings:
af9033.c: In function 'af9033_read_status':
af9033.c:883:25: warning: 'snr_lut' may be used uninitialized in this function [-Wmaybe-uninitialized]
const struct val_snr *snr_lut;
^
af9033.c:952:25: warning: 'tmp' may be used uninitialized in this function [-Wmaybe-uninitialized]
c->cnr.stat[0].svalue = tmp;
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The current code will expose a zero value if one of the stats is
not available, but this is not what userspace expects. Instead,
if something goes wrong on providing some stats, it should be
changing the scale to FE_SCALE_NOT_AVAILABLE.
So, change the logic to do the right thing.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
cxd2841er_read_agc_gain_c added to obtain signal strength.
signal strength now relay on AGC value.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The signal strength value is reversed: the bigger the number,
the weaker is the signal.
Fix the logic and present it in dBm. Please notice that the
dBm measure is actually an estimation, as the ratio is not
fully linear. It also varies with the frequency.
Yet, the estimation should be good enough for programs like
Kaffeine to indicate when the signal is good or bad.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
It is a good idea to measure the signal strength while
tuning, as this helps to identify if the antenna is ok.
Also, such measure helps to identify the quality of the
signal.
Do some changes to enable it before signal lock. While
here, optimize the code to only initialize the stats
length once, and make sure that, just after set_frontend,
any reading for the stats that depends on lock to return
FE_SCALE_NOT_AVAILABLE.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Disable runtime unbind as driver does not support it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Move statistics polling to read_status() in order to avoid use of
kernel work. Also replace home made sign extension used for
statistics with kernel sign_extend32().
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Disable runtime unbind as driver does not support it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Disable runtime unbind as driver does not support it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Move statistics polling to read_status() in order to avoid use of
kernel work.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
* remove some unneeded variable initialization
* rename variables
* use min() macro to calc max i2c xfer len
* change bad firmware error code from EFAULT to EINVAL
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
There was some calculations where was kHz used in order to keep
calculation withing 32-bit. Convert all to Hz and use 64-bit
division helpers where needed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Simplify TS clock divider calculation and programming slightly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
DiSEqC message sending takes 13.5 ms per byte, which is 54 ms total
when typical 4 byte message is sent. Don't hard-code time limit to
54 ms, but calculate it. Time limit is only used to determine when to
start poll "DiSEqC Tx ready" status from the chip.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
No need to clear negative msb bits as those were dropped in any
case when data is written to register.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Disable runtime unbind as driver does not support it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Si2168-B40 firmware API has changed somewhere between 4.0-11 and
4.0-19 so that sleep will lose firmware upgrade from the chip. Due
to that firmware re-upload is needed when newer firmwares are used.
Rewrote firmware handling logic partly at the same.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
Matthias Schwarzott
Abylay Ospan
Antti Palosaari
Colin Ian King
Julia Lawall
Mauro Carvalho Chehab
Wolfram Sang
Christophe JAILLET
Arnd Bergmann
Mauro Carvalho Chehab
Saso Slavicic
Hans Verkuil