| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In the omap gpmc driver it can be noticed that GPMC_CONFIG4_OEEXTRADELAY
is overwritten by the WEEXTRADELAY value from the device tree and
GPMC_CONFIG4_WEEXTRADELAY is not updated by the value from the device
tree.
As a consequence, the memory accesses cannot be configured properly when
the extra delay are needed for OE and WE.
Fix the update of GPMC_CONFIG4_WEEXTRADELAY with the value from the
device tree file and prevents GPMC_CONFIG4_OEXTRADELAY
being overwritten by the WEXTRADELAY value from the device tree.
Cc: stable@vger.kernel.org
Signed-off-by: Ocquidant, Sebastien <sebastienocquidant@eaton.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
|
|
Pull MTD updates from Brian Norris:
"First cycle with Boris as NAND maintainer! Many (most) bullets stolen
from him.
Generic:
- Migrated NAND LED trigger to be a generic MTD trigger
NAND:
- Introduction of the "ECC algorithm" concept, to avoid overloading
the ECC mode field too much more
- Replaced the nand_ecclayout infrastructure with something a little
more flexible (finally!) and future proof
- Rework of the OMAP GPMC and NAND drivers; the TI folks pulled some
of this into their own tree as well
- Prepare the sunxi NAND driver to receive DMA support
- Handle bitflips in erased pages on GPMI revisions that do not
support this in hardware.
SPI NOR:
- Start using the spi_flash_read() API for SPI drivers that support
it (i.e., SPI drivers with special memory-mapped flash modes)
And other small scattered improvments"
* tag 'for-linus-20160523' of git://git.infradead.org/linux-mtd: (155 commits)
mtd: spi-nor: support GigaDevice gd25lq64c
mtd: nand_bch: fix spelling of "probably"
mtd: brcmnand: respect ECC algorithm set by NAND subsystem
gpmi-nand: Handle ECC Errors in erased pages
Documentation: devicetree: deprecate "soft_bch" nand-ecc-mode value
mtd: nand: add support for "nand-ecc-algo" DT property
mtd: mtd: drop NAND_ECC_SOFT_BCH enum value
mtd: drop support for NAND_ECC_SOFT_BCH as "soft_bch" mapping
mtd: nand: read ECC algorithm from the new field
mtd: nand: fsmc: validate ECC setup by checking algorithm directly
mtd: nand: set ECC algorithm to Hamming on fallback
staging: mt29f_spinand: set ECC algorithm explicitly
CRIS v32: nand: set ECC algorithm explicitly
mtd: nand: atmel: set ECC algorithm explicitly
mtd: nand: davinci: set ECC algorithm explicitly
mtd: nand: bf5xx: set ECC algorithm explicitly
mtd: nand: omap2: Fix high memory dma prefetch transfer
mtd: nand: omap2: Start dma request before enabling prefetch
mtd: nandsim: add __init attribute
mtd: nand: move of_get_nand_xxx() helpers into nand_base.c
...
|
|
Pull drm updates from Dave Airlie:
"Here's the main drm pull request for 4.7, it's been a busy one, and
I've been a bit more distracted in real life this merge window. Lots
more ARM drivers, not sure if it'll ever end. I think I've at least
one more coming the next merge window.
But changes are all over the place, support for AMD Polaris GPUs is in
here, some missing GM108 support for nouveau (found in some Lenovos),
a bunch of MST and skylake fixes.
I've also noticed a few fixes from Arnd in my inbox, that I'll try and
get in asap, but I didn't think they should hold this up.
New drivers:
- Hisilicon kirin display driver
- Mediatek MT8173 display driver
- ARC PGU - bitstreamer on Synopsys ARC SDP boards
- Allwinner A13 initial RGB output driver
- Analogix driver for DisplayPort IP found in exynos and rockchip
DRM Core:
- UAPI headers fixes and C++ safety
- DRM connector reference counting
- DisplayID mode parsing for Dell 5K monitors
- Removal of struct_mutex from drivers
- Connector registration cleanups
- MST robustness fixes
- MAINTAINERS updates
- Lockless GEM object freeing
- Generic fbdev deferred IO support
panel:
- Support for a bunch of new panels
i915:
- VBT refactoring
- PLL computation cleanups
- DSI support for BXT
- Color manager support
- More atomic patches
- GEM improvements
- GuC fw loading fixes
- DP detection fixes
- SKL GPU hang fixes
- Lots of BXT fixes
radeon/amdgpu:
- Initial Polaris support
- GPUVM/Scheduler/Clock/Power improvements
- ASYNC pageflip support
- New mesa feature support
nouveau:
- GM108 support
- Power sensor support improvements
- GR init + ucode fixes.
- Use GPU provided topology information
vmwgfx:
- Add host messaging support
gma500:
- Some cleanups and fixes
atmel:
- Bridge support
- Async atomic commit support
fsl-dcu:
- Timing controller for LCD support
- Pixel clock polarity support
rcar-du:
- Misc fixes
exynos:
- Pipeline clock support
- Exynoss4533 SoC support
- HW trigger mode support
- export HDMI_PHY clock
- DECON5433 fixes
- Use generic prime functions
- use DMA mapping APIs
rockchip:
- Lots of little fixes
vc4:
- Render node support
- Gamma ramp support
- DPI output support
msm:
- Mostly cleanups and fixes
- Conversion to generic struct fence
etnaviv:
- Fix for prime buffer handling
- Allow hangcheck to be coalesced with other wakeups
tegra:
- Gamme table size fix"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1050 commits)
drm/edid: add displayid detailed 1 timings to the modelist. (v1.1)
drm/edid: move displayid validation to it's own function.
drm/displayid: Iterate over all DisplayID blocks
drm/edid: move displayid tiled block parsing into separate function.
drm: Nuke ->vblank_disable_allowed
drm/vmwgfx: Report vmwgfx version to vmware.log
drm/vmwgfx: Add VMWare host messaging capability
drm/vmwgfx: Kill some lockdep warnings
drm/nouveau/gr/gf100-: fix race condition in fecs/gpccs ucode
drm/nouveau/core: recognise GM108 chipsets
drm/nouveau/gr/gm107-: fix touching non-existent ppcs in attrib cb setup
drm/nouveau/gr/gk104-: share implementation of ppc exception init
drm/nouveau/gr/gk104-: move rop_active_fbps init to nonctx
drm/nouveau/bios/pll: check BIT table version before trying to parse it
drm/nouveau/bios/pll: prevent oops when limits table can't be parsed
drm/nouveau/volt/gk104: round up in gk104_volt_set
drm/nouveau/fb/gm200: setup mmu debug buffer registers at init()
drm/nouveau/fb/gk20a,gm20b: setup mmu debug buffer registers at init()
drm/nouveau/fb/gf100-: allocate mmu debug buffers
drm/nouveau/fb: allow chipset-specific actions for oneinit()
...
|
|
Pull char / misc driver updates from Greg KH:
"Here's the big char and misc driver update for 4.7-rc1.
Lots of different tiny driver subsystems have updates here with new
drivers and functionality. Details in the shortlog.
All have been in linux-next with no reported issues for a while"
* tag 'char-misc-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (125 commits)
mcb: Delete num_cells variable which is not required
mcb: Fixed bar number assignment for the gdd
mcb: Replace ioremap and request_region with the devm version
mcb: Implement bus->dev.release callback
mcb: export bus information via sysfs
mcb: Correctly initialize the bus's device
mei: bus: call mei_cl_read_start under device lock
coresight: etb10: adjust read pointer only when needed
coresight: configuring ETF in FIFO mode when acting as link
coresight: tmc: implementing TMC-ETF AUX space API
coresight: moving struct cs_buffers to header file
coresight: tmc: keep track of memory width
coresight: tmc: make sysFS and Perf mode mutually exclusive
coresight: tmc: dump system memory content only when needed
coresight: tmc: adding mode of operation for link/sinks
coresight: tmc: getting rid of multiple read access
coresight: tmc: allocating memory when needed
coresight: tmc: making prepare/unprepare functions generic
coresight: tmc: splitting driver in ETB/ETF and ETR components
coresight: tmc: cleaning up header file
...
|
|
To allow building mediatek-drm.ko as a module, the
mtk_smi_larb_get and mtk_smi_larb_put symbols have
to be exported.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Presumably we never use the default: case statement which prints a
warning message. But my static checker complains that if we do, we will
hit an uninitialized variable warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Franklin S Cooper Jr. <fcooper@ti.com>
|
|
The new IFC controller version 2.0 has a different memory map page.
Upto IFC 1.4 PAGE size is 4 KB and from IFC2.0 PAGE size is 64KB.
This patch segregates the IFC global and runtime registers to appropriate
PAGE sizes.
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: Raghav Dogra <raghav@freescale.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Acked-by: Scott Wood <oss@buserror.net>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Implement handling properties in subnodes and adding child devices to the
system. Child devices will not be added if configuration fails.
Since the driver now does more than suspend-resume support, dependency on
CONFIG_PM is removed.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
This patch adds Exynos SROM controller driver which will handle
save restore of SROM registers during S2R.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[p.fedin@samsung.com: tested on SMDK5410]
Tested-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
[k.kozlowski: Minor COMPILE_TEST adjustments in Kconfig entries]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
GPMC_STATUS register is private to the GPMC module and must not be
accessed directly by NAND driver through the gpmc_regs.
They must use gpmc_omap_get_nand_ops() instead.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
OMAPs can have 2 to 4 WAITPINs that can be used as edge triggered
interrupts if not used for memory wait state insertion.
Support these interrupts via the gpmc IRQ domain.
The gpmc IRQ domain interrupt map is:
0 - NAND_fifoevent
1 - NAND_termcount
2 - GPMC_WAIT0 edge
3 - GPMC_WAIT1 edge, and so on
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
If the device attached to GPMC wants to use the WAIT pin
for WAIT monitoring then we reserve it internally for
exclusive use.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
OMAPs can have 2 to 4 WAITPINs that can be used as general purpose
input if not used for memory wait state insertion.
The first user will be the OMAP NAND chip to get the NAND
read/busy status using gpiolib.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
We have been preventing mapping GPMC children in the
first 1MB but really it has to be the first 16MB as
the minimum GPMC partition size is 16MB.
Also print an error message if CS mapping fails
due to DT requesting address outside the GPMC
map.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Move NAND specific device tree parsing to NAND driver.
The NAND controller node must have a compatible id, register space
resource and interrupt resource.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
GPMC provides 2 interrupts for NAND use. i.e. fifoevent and termcount.
Use IRQ domain for this. NAND device tree node can then
get the necessary interrupts by using gpmc as the interrupt parent.
Legacy boot uses gpmc_get_client_irq to get the
NAND interrupts from the GPMC IRQ domain.
Get rid of custom bitmasks and use IRQ domain for that
as well.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
This is needed by OMAP NAND driver to poll the empty status
of the writebuffer.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
The OMAP GPMC module has certain registers dedicated for NAND
access and some NAND bits mixed with other GPMC functionality.
For the NAND dedicated registers we have the struct gpmc_nand_regs.
The NAND driver needs to access NAND specific bits from the
following non-dedicated registers
- EMPTYWRITEBUFFERSTATUS from GPMC_STATUS
For accessing these bits we introduce the struct gpmc_nand_ops.
Add gpmc_omap_get_nand_ops() that returns the gpmc_nand_ops along
with updating the gpmc_nand_regs. This API will be called by the
OMAP NAND driver to access the necessary bits in GPMC register space.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Pull MTD updates from Brian Norris:
"NAND:
- Add sunxi_nand randomizer support
- begin refactoring NAND ecclayout structs
- fix pxa3xx_nand dmaengine usage
- brcmnand: fix support for v7.1 controller
- add Qualcomm NAND controller driver
SPI NOR:
- add new ls1021a, ls2080a support to Freescale QuadSPI
- add new flash ID entries
- support bottom-block protection for Winbond flash
- support Status Register Write Protect
- remove broken QPI support for Micron SPI flash
JFFS2:
- improve post-mount CRC scan efficiency
General:
- refactor bcm63xxpart parser, to later extend for NAND
- add writebuf size parameter to mtdram
Other minor code quality improvements"
* tag 'for-linus-20160324' of git://git.infradead.org/linux-mtd: (72 commits)
mtd: nand: remove kerneldoc for removed function parameter
mtd: nand: Qualcomm NAND controller driver
dt/bindings: qcom_nandc: Add DT bindings
mtd: nand: don't select chip in nand_chip's block_bad op
mtd: spi-nor: support lock/unlock for a few Winbond chips
mtd: spi-nor: add TB (Top/Bottom) protect support
mtd: spi-nor: add SPI_NOR_HAS_LOCK flag
mtd: spi-nor: use BIT() for flash_info flags
mtd: spi-nor: disallow further writes to SR if WP# is low
mtd: spi-nor: make lock/unlock bounds checks more obvious and robust
mtd: spi-nor: silently drop lock/unlock for already locked/unlocked region
mtd: spi-nor: wait for SR_WIP to clear on initial unlock
mtd: nand: simplify nand_bch_init() usage
mtd: mtdswap: remove useless if (!mtd->ecclayout) test
mtd: create an mtd_oobavail() helper and make use of it
mtd: kill the ecclayout->oobavail field
mtd: nand: check status before reporting timeout
mtd: bcm63xxpart: give width specifier an 'int', not 'size_t'
mtd: mtdram: Add parameter for setting writebuf size
mtd: nand: pxa3xx_nand: kill unused field 'drcmr_cmd'
...
|
|
Pull IOMMU updates from Joerg Roedel:
- updates for the Exynos IOMMU driver to make use of default domains
and to add support for the SYSMMU v5
- new Mediatek IOMMU driver
- support for the ARMv7 short descriptor format in the io-pgtable code
- default domain support for the ARM SMMU
- couple of other small fixes all over the place
* tag 'iommu-updates-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (41 commits)
iommu/ipmmu-vmsa: Add r8a7795 DT binding
iommu/mediatek: Check for NULL instead of IS_ERR()
iommu/io-pgtable-armv7s: Fix kmem_cache_alloc() flags
iommu/mediatek: Fix handling of of_count_phandle_with_args result
iommu/dma: Fix NEED_SG_DMA_LENGTH dependency
iommu/mediatek: Mark PM functions as __maybe_unused
iommu/mediatek: Select ARM_DMA_USE_IOMMU
iommu/exynos: Use proper readl/writel register interface
iommu/exynos: Pointers are nto physical addresses
dts: mt8173: Add iommu/smi nodes for mt8173
iommu/mediatek: Add mt8173 IOMMU driver
memory: mediatek: Add SMI driver
dt-bindings: mediatek: Add smi dts binding
dt-bindings: iommu: Add binding for mediatek IOMMU
iommu/ipmmu-vmsa: Use ARCH_RENESAS
iommu/exynos: Support multiple attach_device calls
iommu/exynos: Add Maintainers entry for Exynos SYSMMU driver
iommu/exynos: Add support for v5 SYSMMU
iommu/exynos: Update device tree documentation
iommu/exynos: Add support for SYSMMU controller with bogus version reg
...
|
|
This patch add SMI(Smart Multimedia Interface) driver. This driver
is responsible to enable/disable iommu and control the power domain
and clocks of each local arbiter.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Tested-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
In order to support extended timings parameters on hardware supporting the
"AAD" mode like the AM335x or DM816x, add these entries into the GPMC driver
if the hardware is capable.
Tested on DM816x and AM335x.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
|
|
Replacing the NO_IRQ macro with 0. If there is no interrupt,
returned value will be 0 regardless of what NO_IRQ is defined.
Signed-off-by: Raghav Dogra <raghav@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs. Some for SoC-family code under
drivers/soc, but also some other driver updates that don't belong
anywhere else. We also bring in the drivers/reset code through
arm-soc.
Some of the larger updates:
- Qualcomm support for SMEM, SMSM, SMP2P. All used to communicate
with other parts of the chip/board on these platforms, all
proprietary protocols that don't fit into other subsystems and live
in drivers/soc for now.
- System bus driver for UniPhier
- Driver for the TI Wakeup M3 IPC device
- Power management for Raspberry PI
+ Again a bunch of other smaller updates and patches"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
bus: uniphier: allow only built-in driver
ARM: bcm2835: clarify RASPBERRYPI_FIRMWARE dependency
MAINTAINERS: Drop Kumar Gala from QCOM
bus: uniphier-system-bus: add UniPhier System Bus driver
ARM: bcm2835: add rpi power domain driver
dt-bindings: add rpi power domain driver bindings
ARM: bcm2835: Define two new packets from the latest firmware.
drivers/soc: make mediatek/mtk-scpsys.c explicitly non-modular
soc: mediatek: SCPSYS: Add regulator support
MAINTAINERS: Change QCOM entries
soc: qcom: smd-rpm: Add existing platform support
memory/tegra: Add number of TLB lines for Tegra124
reset: hi6220: fix modular build
soc: qcom: Introduce WCNSS_CTRL SMD client
ARM: qcom: select ARM_CPU_SUSPEND for power management
MAINTAINERS: Add rules for Qualcomm dts files
soc: qcom: enable smsm/smp2p modular build
serial: msm_serial: Make config tristate
soc: qcom: smp2p: Qualcomm Shared Memory Point to Point
soc: qcom: smsm: Add driver for Qualcomm SMSM
...
|
|
Need to include sched.h to fix the following compilation error
if FSL_IFC is enabled on ARM64 machine.
In file included from include/linux/mmzone.h:9:0,
from include/linux/gfp.h:5,
from include/linux/kmod.h:22,
from include/linux/module.h:13,
from drivers/memory/fsl_ifc.c:22:
drivers/memory/fsl_ifc.c: In function ‘check_nand_stat’:
include/linux/wait.h:165:35: error: ‘TASK_NORMAL’ undeclared (first use in this function)
#define wake_up(x) __wake_up(x, TASK_NORMAL, 1, NULL)
^
drivers/memory/fsl_ifc.c:136:3: note: in expansion of macro ‘wake_up’
wake_up(&ctrl->nand_wait);
^
include/linux/wait.h:165:35: note: each undeclared identifier is reported only once for each function it appears in
#define wake_up(x) __wake_up(x, TASK_NORMAL, 1, NULL)
^
drivers/memory/fsl_ifc.c:136:3: note: in expansion of macro ‘wake_up’
wake_up(&ctrl->nand_wait);
^
Analysis is as follows:
I put some instrumental code and get the
following .h files inclusion sequence:
In file included from ./arch/arm64/include/asm/compat.h:25:0,
from ./arch/arm64/include/asm/stat.h:23,
from include/linux/stat.h:5,
from include/linux/module.h:10,
from drivers/memory/fsl_ifc.c:23:
include/linux/sched.h:113:1: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘struct’
struct sched_attr {
^
CONFIG_COMPAT=y is enabled while 39 and 48 bit VA is selected.
When 42 bit VA is selected, it does not enable CONFIG_COMPAT=y
In ./arch/arm64/include/asm/stat.h:23, it has
"#ifdef CONFIG_COMPAT"
"#include <asm/compat.h>"
"..."
"#endif"
Since ./arch/arm64/include/asm/stat.h does not
include ./arch/arm64/include/asm/compat.h,
then it will not include include/linux/sched.h
Hence we have to manually add "#include <linux/sched.h>"
in drivers/memory/fsl_ifc.c
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Tegra124 was accidentally left out when the number of TLB lines was
parameterized in commit 11cec15bf3fb ("iommu/tegra-smmu: Parameterize
number of TLB lines"). Fortunately this doesn't cause any noticeable
regressions upstream, presumably because there aren't any use-cases
that exercise enough pressure on the SMMU. But it is a regression
nonetheless, so let's fix it.
Fixes: 11cec15bf3fb ("iommu/tegra-smmu: Parameterize number of TLB lines")
Signed-off-by: Vince Hsu <vince.h@nvidia.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
[treding@nvidia.com: extract from unrelated patch]
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Pull ARM SoC driver updates from Olof Johansson:
"As we've enabled multiplatform kernels on ARM, and greatly done away
with the contents under arch/arm/mach-*, there's still need for
SoC-related drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to
communicate with power management blocks on these SoCs for use by
clock, regulator and bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with
PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be
confused with PSCI (Power State Coordination Interface). SCPI is
used to communicate with the assistant embedded cores doing power
management, and we have yet to see how many of them will implement
this for their hardware vs abstracting in other ways (or not at all
like in the past).
- To make confusion between SCPI and PSCI more likely, this release
also includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits)
soc: qcom: smd-rpm: Correct size of outgoing message
bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus
bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings
ARM: bcm2835: add mutual inclusion protection
drivers: psci: make PSCI 1.0 functions initialization version dependent
dt-bindings: Correct paths in Rockchip power domains binding document
soc: rockchip: power-domain: don't try to print the clock name in error case
soc: qcom/smem: add HWSPINLOCK dependency
clk: berlin: add cpuclk
ARM: berlin: dts: add CLKID_CPU for BG2Q
ARM: bcm2835: Add the Raspberry Pi firmware driver
soc: qcom: smem: Move RPM message ram out of smem DT node
soc: qcom: smd-rpm: Correct the active vs sleep state flagging
soc: qcom: smd: delete unneeded of_node_put
firmware: qcom-scm: build for correct architecture level
soc: qcom: smd: Correct SMEM items for upper channels
qcom-scm: add missing prototype for qcom_scm_is_available()
qcom-scm: fix endianess issue in __qcom_scm_is_call_available
soc: qcom: smd: Reject send of too big packets
soc: qcom: smd: Handle big endian CPUs
...
|
|
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver update for 4.4-rc1. Lots of
different driver and subsystem updates, hwtracing being the largest
with the addition of some new platforms that are now supported. Full
details in the shortlog.
All of these have been in linux-next for a long time with no reported
issues"
* tag 'char-misc-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (181 commits)
fpga: socfpga: Fix check of return value of devm_request_irq
lkdtm: fix ACCESS_USERSPACE test
mcb: Destroy IDA on module unload
mcb: Do not return zero on error path in mcb_pci_probe()
mei: bus: set the device name before running fixup
mei: bus: use correct lock ordering
mei: Fix debugfs filename in error output
char: ipmi: ipmi_ssif: Replace timeval with timespec64
fpga: zynq-fpga: Fix issue with drvdata being overwritten.
fpga manager: remove unnecessary null pointer checks
fpga manager: ensure lifetime with of_fpga_mgr_get
fpga: zynq-fpga: Change fw format to handle bin instead of bit.
fpga: zynq-fpga: Fix unbalanced clock handling
misc: sram: partition base address belongs to __iomem space
coresight: etm3x: adding documentation for sysFS's cpu interface
vme: 8-bit status/id takes 256 values, not 255
fpga manager: Adding FPGA Manager support for Xilinx Zynq 7000
ARM: zynq: dt: Updated devicetree for Zynq 7000 platform.
ARM: dt: fpga: Added binding docs for Xilinx Zynq FPGA manager.
ver_linux: proc/modules, limit text processing to 'sed'
...
|
|
When gpmc_cs_show_timings is called in gpmc_cs_set_timings()
gpmc_cs_program_settings() was already run which modifies the CONFIG1
register. So to be more useful do the "before" dump earlier.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 63aa945b1013 ("memory: omap-gpmc: Add Kconfig option for debug")
added a debug option for GPMC, but somehow managed to keep it unselectable.
This probably happened because I had some uncommitted changes and the
GPMC option is selected in the platform specific Kconfig.
Let's also update the description a bit, it does not mention that
enabling the debug option also disables the reset of GPMC controller
during the init as pointed out by Uwe Kleine-König
<u.kleine-koenig@pengutronix.de> and Roger Quadros <rogerq@ti.com>.
Fixes: 63aa945b1013 ("memory: omap-gpmc: Add Kconfig option for debug")
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The change adds support of ARM PrimeCell PL176 MPMC.
Static memory configuration of PL175 MPMC is very similar to one found
on PL172 and PL175 controllers, so it is preferred to add its support
into the existing driver. The difference is that PL176 supports up to
10 slave ports (but only 4 of them may be connected to static memory
devices), AHB master bus width cab be 64-bit wide, also NAND devices
can be interfaced.
Similar to PL175 contoller, PL176 has no write buffer enable control
in static memory configuration register, the rest of static memory
configuration bits (with exception of NAND) is the same.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
|
|
The change adds support of ARM PrimeCell PL175 MPMC, the controller is
found on NXP LPC32xx SoC.
PL175 MPMC is very similar to PL172 controller, so it is preferred to
add its support into the existing driver.
One of the differences between PL172 and PL175 is that the latter one
supports up to 6 AHB ports, but still only 4 AHB ports can be assigned
to a static memory device, also PL175 does not have write buffer
enable control in static memory configuration register.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
|
|
According to PL172 TRM read of bits [7:6] of MPMCPeriphID3 is
undefined, so unmask them. Also the driver supports all currently
present revisions of PL172, this allows to alleviate requirements to
the revision version matched by the driver.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
|
|
Pull iommu updates for from Joerg Roedel:
"This time the IOMMU updates are mostly cleanups or fixes. No big new
features or drivers this time. In particular the changes include:
- Bigger cleanup of the Domain<->IOMMU data structures and the code
that manages them in the Intel VT-d driver. This makes the code
easier to understand and maintain, and also easier to keep the data
structures in sync. It is also a preparation step to make use of
default domains from the IOMMU core in the Intel VT-d driver.
- Fixes for a couple of DMA-API misuses in ARM IOMMU drivers, namely
in the ARM and Tegra SMMU drivers.
- Fix for a potential buffer overflow in the OMAP iommu driver's
debug code
- A couple of smaller fixes and cleanups in various drivers
- One small new feature: Report domain-id usage in the Intel VT-d
driver to easier detect bugs where these are leaked"
* tag 'iommu-updates-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (83 commits)
iommu/vt-d: Really use upper context table when necessary
x86/vt-d: Fix documentation of DRHD
iommu/fsl: Really fix init section(s) content
iommu/io-pgtable-arm: Unmap and free table when overwriting with block
iommu/io-pgtable-arm: Move init-fn declarations to io-pgtable.h
iommu/msm: Use BUG_ON instead of if () BUG()
iommu/vt-d: Access iomem correctly
iommu/vt-d: Make two functions static
iommu/vt-d: Use BUG_ON instead of if () BUG()
iommu/vt-d: Return false instead of 0 in irq_remapping_cap()
iommu/amd: Use BUG_ON instead of if () BUG()
iommu/amd: Make a symbol static
iommu/amd: Simplify allocation in irq_remapping_alloc()
iommu/tegra-smmu: Parameterize number of TLB lines
iommu/tegra-smmu: Factor out tegra_smmu_set_pde()
iommu/tegra-smmu: Extract tegra_smmu_pte_get_use()
iommu/tegra-smmu: Use __GFP_ZERO to allocate zeroed pages
iommu/tegra-smmu: Remove PageReserved manipulation
iommu/tegra-smmu: Convert to use DMA API
iommu/tegra-smmu: smmu_flush_ptc() wants device addresses
...
|
|
Pull powerpc updates from Michael Ellerman:
- support "hybrid" iommu/direct DMA ops for coherent_mask < dma_mask
from Benjamin Herrenschmidt
- EEH fixes for SRIOV from Gavin
- introduce rtas_get_sensor_fast() for IRQ handlers from Thomas Huth
- use hardware RNG for arch_get_random_seed_* not arch_get_random_*
from Paul Mackerras
- seccomp filter support from Michael Ellerman
- opal_cec_reboot2() handling for HMIs & machine checks from Mahesh
Salgaonkar
- add powerpc timebase as a trace clock source from Naveen N. Rao
- misc cleanups in the xmon, signal & SLB code from Anshuman Khandual
- add an inline function to update POWER8 HID0 from Gautham R. Shenoy
- fix pte_pagesize_index() crash on 4K w/64K hash from Michael Ellerman
- drop support for 64K local store on 4K kernels from Michael Ellerman
- move dma_get_required_mask() from pnv_phb to pci_controller_ops from
Andrew Donnellan
- initialize distance lookup table from drconf path from Nikunj A
Dadhania
- enable RTC class support from Vaibhav Jain
- disable automatically blocked PCI config from Gavin Shan
- add LEDs driver for PowerNV platform from Vasant Hegde
- fix endianness issues in the HVSI driver from Laurent Dufour
- kexec endian fixes from Samuel Mendoza-Jonas
- fix corrupted pdn list from Gavin Shan
- fix fenced PHB caused by eeh_slot_error_detail() from Gavin Shan
- Freescale updates from Scott: Highlights include 32-bit memcpy/memset
optimizations, checksum optimizations, 85xx config fragments and
updates, device tree updates, e6500 fixes for non-SMP, and misc
cleanup and minor fixes.
- a ton of cxl updates & fixes:
- add explicit precision specifiers from Rasmus Villemoes
- use more common format specifier from Rasmus Villemoes
- destroy cxl_adapter_idr on module_exit from Johannes Thumshirn
- destroy afu->contexts_idr on release of an afu from Johannes
Thumshirn
- compile with -Werror from Daniel Axtens
- EEH support from Daniel Axtens
- plug irq_bitmap getting leaked in cxl_context from Vaibhav Jain
- add alternate MMIO error handling from Ian Munsie
- allow release of contexts which have been OPENED but not STARTED
from Andrew Donnellan
- remove use of macro DEFINE_PCI_DEVICE_TABLE from Vaishali Thakkar
- release irqs if memory allocation fails from Vaibhav Jain
- remove racy attempt to force EEH invocation in reset from Daniel
Axtens
- fix + cleanup error paths in cxl_dev_context_init from Ian Munsie
- fix force unmapping mmaps of contexts allocated through the kernel
api from Ian Munsie
- set up and enable PSL Timebase from Philippe Bergheaud
* tag 'powerpc-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (140 commits)
cxl: Set up and enable PSL Timebase
cxl: Fix force unmapping mmaps of contexts allocated through the kernel api
cxl: Fix + cleanup error paths in cxl_dev_context_init
powerpc/eeh: Fix fenced PHB caused by eeh_slot_error_detail()
powerpc/pseries: Cleanup on pci_dn_reconfig_notifier()
powerpc/pseries: Fix corrupted pdn list
powerpc/powernv: Enable LEDS support
powerpc/iommu: Set default DMA offset in dma_dev_setup
cxl: Remove racy attempt to force EEH invocation in reset
cxl: Release irqs if memory allocation fails
cxl: Remove use of macro DEFINE_PCI_DEVICE_TABLE
powerpc/powernv: Fix mis-merge of OPAL support for LEDS driver
powerpc/powernv: Reset HILE before kexec_sequence()
powerpc/kexec: Reset secondary cpu endianness before kexec
powerpc/hvsi: Fix endianness issues in the HVSI driver
leds/powernv: Add driver for PowerNV platform
powerpc/powernv: Create LED platform device
powerpc/powernv: Add OPAL interfaces for accessing and modifying system LED states
powerpc/powernv: Fix the log message when disabling VF
cxl: Allow release of contexts which have been OPENED but not STARTED
...
|
|
Pull ARM SoC driver updates from Olof Johansson:
"Some releases this branch is nearly empty, others we have more stuff.
It tends to gather drivers that need SoC modification or dependencies
such that they have to (also) go in through our tree.
For this release, we have merged in part of the reset controller tree
(with handshake that the parts we have merged in will remain stable),
as well as dependencies on a few clock branches.
In general, new items here are:
- Qualcomm driver for SMM/SMD, which is how they communicate with the
coprocessors on (some) of their platforms
- memory controller work for ARM's PL172 memory controller
- reset drivers for various platforms
- PMU power domain support for Marvell platforms
- Tegra support for T132/T210 SoCs: PMC, fuse, memory controller
per-SoC support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (49 commits)
ARM: tegra: cpuidle: implement cpuidle_state.enter_freeze()
ARM: tegra: Disable cpuidle if PSCI is available
soc/tegra: pmc: Use existing pclk reference
soc/tegra: pmc: Remove unnecessary return statement
soc: tegra: Remove redundant $(CONFIG_ARCH_TEGRA) in Makefile
memory: tegra: Add Tegra210 support
memory: tegra: Add support for a variable-size client ID bitfield
clk: shmobile: rz: Add CPG/MSTP Clock Domain support
clk: shmobile: rcar-gen2: Add CPG/MSTP Clock Domain support
clk: shmobile: r8a7779: Add CPG/MSTP Clock Domain support
clk: shmobile: r8a7778: Add CPG/MSTP Clock Domain support
clk: shmobile: Add CPG/MSTP Clock Domain support
ARM: dove: create a proper PMU driver for power domains, PMU IRQs and resets
reset: reset-zynq: Adding support for Xilinx Zynq reset controller.
docs: dts: Added documentation for Xilinx Zynq Reset Controller bindings.
MIPS: ath79: Add the reset controller to the AR9132 dtsi
reset: Add a driver for the reset controller on the AR71XX/AR9XXX
devicetree: Add bindings for the ATH79 reset controller
reset: socfpga: Update reset-socfpga to read the altr,modrst-offset property
doc: dt: add documentation for lpc1850-rgu reset driver
...
|
|
Pull ARM SoC platform updates from Olof Johansson:
"New or improved SoC support:
- add support for Atmel's SAMA5D2 SoC
- add support for Freescale i.MX6UL
- improved support for TI's DM814x platform
- misc fixes and improvements for RockChip platforms
- Marvell MVEBU suspend/resume support
A few driver changes that ideally would belong in the drivers branch
are also here (acked by appropriate maintainers):
- power key input driver for Freescale platforms (svns)
- RTC driver updates for Freescale platforms (svns/mxc)
- clk fixes for TI DM814/816X
+ a bunch of other changes for various platforms"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: rockchip: pm: Fix PTR_ERR() argument
ARM: imx: mach-imx6ul: Fix allmodconfig build
clk: ti: fix for definition movement
ARM: uniphier: drop v7_invalidate_l1 call at secondary entry
memory: kill off set_irq_flags usage
rtc: snvs: select option REGMAP_MMIO
ARM: brcmstb: select ARCH_DMA_ADDR_T_64BIT for LPAE
ARM: BCM: Enable ARM erratum 798181 for BRCMSTB
ARM: OMAP2+: Fix power domain operations regression caused by 81xx
ARM: rockchip: enable PMU_GPIOINT_WAKEUP_EN when entering shallow suspend
ARM: rockchip: set correct stabilization thresholds in suspend
ARM: rockchip: rename osc_switch_to_32k variable
ARM: imx6ul: add fec MAC refrence clock and phy fixup init
ARM: imx6ul: add fec bits to GPR syscon definition
rtc: mxc: add support of device tree
dt-binding: document the binding for mxc rtc
rtc: mxc: use a second rtc clock
ARM: davinci: cp_intc: use IRQCHIP_SKIP_SET_WAKE instead of irq_set_wake callback
soc: mediatek: Fix SCPSYS compilation
ARM: at91/soc: add basic support for new sama5d2 SoC
...
|
|
ARM: tegra: Memory controller updates for v4.3-rc1
Adds support for Tegra210, which allows the SMMU to be used on this new
SoC generation.
* tag 'tegra-for-4.3-memory' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
memory: tegra: Add Tegra210 support
memory: tegra: Add support for a variable-size client ID bitfield
memory: tegra: Expose supported rates via debugfs
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
iommu/tegra-smmu: Changes for v4.3-rc1
A bunch of improvements by Russell King, along with a fix to restore
display support when using the SMMU. This was due to the SMMU driver
writing the wrong value of active TLB lines, effectively disabling the
TLB and causing massive underflows on the display controller because
of the latency introduced by the SMMU.
|
|
The number of TLB lines was increased from 16 on Tegra30 to 32 on
Tegra114 and later. Parameterize the value so that the initial default
can be set accordingly.
On Tegra30, initializing the value to 32 would effectively disable the
TLB and hence cause massive latencies for memory accesses translated
through the SMMU. This is especially noticeable for isochronuous clients
such as display, whose FIFOs would continuously underrun.
Fixes: 891846516317 ("memory: Add NVIDIA Tegra memory controller support")
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add the table of memory clients and SWGROUPs for Tegra210 to enable SMMU
support for this new SoC.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Recent versions of the Tegra MC hardware extend the size of the client
ID bitfield in the MC_ERR_STATUS register by one bit. While one could
simply extend the bitfield for older hardware, that would allow data
from reserved bits into the driver code, which is generally a bad idea
on principle. So this patch instead passes in the client ID mask from
from the per-SoC MC data.
There's no MC support for T210 (yet), but when that support winds up
in the kernel, the appropriate soc->client_id_mask value for that chip
will be 0xff.
Based on an original patch by David Ung <davidu@nvidia.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: David Ung <davidu@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Drivers should not be using __cpuc_* functions nor outer_cache_flush()
directly. This change partly cleans up tegra-smmu.c.
The only difference between cache handling of the tegra variants is
Denver, which omits the call to outer_cache_flush(). This is due to
Denver being an ARM64 CPU, and the ARM64 architecture does not provide
this function. (This, in itself, is a good reason why these should not
be used.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[treding@nvidia.com: fix build failure on 64-bit ARM]
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
set_irq_flags is ARM specific with custom flags which have genirq
equivalents. Convert drivers to use the genirq interfaces directly, so we
can kill off set_irq_flags. The translation of flags is as follows:
IRQF_VALID -> !IRQ_NOREQUEST
IRQF_PROBE -> !IRQ_NOPROBE
IRQF_NOAUTOEN -> IRQ_NOAUTOEN
For IRQs managed by an irqdomain, the irqdomain core code handles clearing
and setting IRQ_NOREQUEST already, so there is no need to do this in
.map() functions and we can simply remove the set_irq_flags calls. Some
users also set IRQ_NOPROBE and this has been maintained although it is not
clear that is really needed. There appears to be a great deal of blind
copy and paste of this code.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Roger Quadros <rogerq@ti.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
If for some reason the GPMC device hasn't been probed yet, gpmc_base is
going to be NULL. Because there's no context yet to be saved, just turn
these functions into no-ops until that device gets probed.
Unable to handle kernel NULL pointer dereference at virtual address 00000010
pgd = c0204000
[00000010] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.2.0-rc5-next-20150804-05947-g23f38fe8eda9 #1
Hardware name: Generic OMAP3-GP (Flattened Device Tree)
task: c0e623e8 ti: c0e5c000 task.ti: c0e5c000
PC is at omap3_gpmc_save_context+0x8/0xc4
LR is at omap_sram_idle+0x154/0x23c
pc : [<c087c7ac>] lr : [<c023262c>] psr: 60000193
sp : c0e5df40 ip : c0f92a80 fp : c0999eb0
r10: c0e57364 r9 : c0e66f14 r8 : 00000003
r7 : 00000000 r6 : 00000003 r5 : 00000000 r4 : c0f5f174
r3 : c0fa4fe8 r2 : 00000000 r1 : 00000000 r0 : fa200280
Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c5387d Table: 80204019 DAC: 00000015
Process swapper/0 (pid: 0, stack limit = 0xc0e5c220)
Stack: (0xc0e5df40 to 0xc0e5e000)
df40: 00000000 c0e66ef8 c0f5f1a4 00000000 00000003 c02333a4 c3813822 00000000
df60: 00000000 c0e5a5c8 cfb8a5d0 c07f0c44 0e4f1d7e 00000000 00000000 00000000
df80: c3813822 00000000 cfb8a5d0 c0e5e4e4 cfb8a5d0 c0e66f14 c0e5a5c8 c0e5e54c
dfa0: c0e5e544 c0e57364 c0999eb0 c0277758 000000fa c0f5d000 00000000 c0d61c18
dfc0: ffffffff ffffffff 00000000 c0d61674 00000000 c0df7a48 00000000 c0f5d5d4
dfe0: c0e5e4c0 c0df7a44 c0e634f8 80204059 00000000 8020807c 00000000 00000000
[<c087c7ac>] (omap3_gpmc_save_context) from [<c023262c>] (omap_sram_idle+0x154/0x23c)
[<c023262c>] (omap_sram_idle) from [<c02333a4>] (omap3_enter_idle_bm+0xec/0x1a8)
[<c02333a4>] (omap3_enter_idle_bm) from [<c07f0c44>] (cpuidle_enter_state+0xbc/0x284)
[<c07f0c44>] (cpuidle_enter_state) from [<c0277758>] (cpu_startup_entry+0x174/0x24c)
[<c0277758>] (cpu_startup_entry) from [<c0d61c18>] (start_kernel+0x358/0x3c0)
[<c0d61c18>] (start_kernel) from [<8020807c>] (0x8020807c)
Code: c0ccace8 c0ccacc0 e59f30b4 e5932000 (e5921010)
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Suggested-by: Javier Martinez Canillas <javier@dowhile0.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Roger Quadros <rogerq@ti.com>
[tony@atomide.com: updated description as suggested by Javier]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
IFC IO accressor are set at run time based
on IFC IP registers endianness.IFC node in
DTS file contains information about
endianness.
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
|
|
Building pl172 as a module fails with:
> ERROR: "of_default_bus_match_table" [drivers/memory/pl172.ko] undefined!
Because the symbol of_default_bus_match_table isn't exported by the OF
core code so can't be referenced from modules. Fix this by removing
the usage of of_default_bus_match_table for now. The side effect of
this is that child nodes can't use "simple-bus" or "simple-mfd".
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
Ocquidant, Sebastien
Linus Torvalds
Philipp Zabel
Dan Carpenter
Boris Brezillon
Raghav Dogra
Pavel Fedin
Pankaj Dubey
Roger Quadros
Yong Wu
Neil Armstrong
Raghav Dogra
Lijun Pan
Vince Hsu
Uwe Kleine-König
Tony Lindgren
Luis de Bethencourt
Vladimir Zapolskiy
Olof Johansson
Joerg Roedel
Thierry Reding
Paul Walmsley
Russell King
Rob Herring
Tomeu Vizoso
Jaiprakash Singh
Joachim Eastwood