| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The PCI vendor id of U.S. Robotics isn't defined in pci_ids.h so far,
only ISDN driver w6692 has a private definition. Move the definition
to pci_ids.h and use it in the r8169 driver too.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to 80ba92fa1a92 ("codel: add ce_threshold attribute")
After EDT adoption, it became easier to implement DCTCP-like CE marking.
In many cases, queues are not building in the network fabric but on
the hosts themselves.
If packets leaving fq missed their Earliest Departure Time by XXX usec,
we mark them with ECN CE. This gives a feedback (after one RTT) to
the sender to slow down and find better operating mode.
Example :
tc qd replace dev eth0 root fq ce_threshold 2.5ms
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FQ pacing guarantees that paced packets queued by one flow do not
add head-of-line blocking for other flows.
After TCP GSO conversion, increasing limit_output_bytes to 1 MB is safe,
since this maps to 16 skbs at most in qdisc or device queues.
(or slightly more if some drivers lower {gso_max_segs|size})
We still can queue at most 1 ms worth of traffic (this can be scaled
by wifi drivers if they need to)
Tested:
# ethtool -c eth0 | egrep "tx-usecs:|tx-frames:" # 40 Gbit mlx4 NIC
tx-usecs: 16
tx-frames: 16
# tc qdisc replace dev eth0 root fq
# for f in {1..10};do netperf -P0 -H lpaa24,6 -o THROUGHPUT;done
Before patch:
27711
26118
27107
27377
27712
27388
27340
27117
27278
27509
After patch:
37434
36949
36658
36998
37711
37291
37605
36659
36544
37349
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tcp_tso_should_defer() first heuristic is to not defer
if last send is "old enough".
Its current implementation uses jiffies and its low granularity.
TSO autodefer performance should not rely on kernel HZ :/
After EDT conversion, we have state variables in nanoseconds that
can allow us to properly implement the heuristic.
This patch increases TSO chunk sizes on medium rate flows,
especially when receivers do not use GRO or similar aggregation.
It also reduces bursts for HZ=100 or HZ=250 kernels, making TCP
behavior more uniform.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tcp_tso_should_defer() last step tries to check if the probable
next ACK packet is coming in less than half rtt.
Problem is that the head->tstamp might be in the future,
so we need to use signed arithmetics to avoid overflows.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Applications using MSG_EOR are giving a strong hint to TCP stack :
Subsequent sendmsg() can not append more bytes to skbs having
the EOR mark.
Do not try to TSO defer suchs skbs, there is really no hope.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bitwise operation is a little faster.
So I replace after() with using the flag FLAG_SND_UNA_ADVANCED as it is
already set before.
In addtion, there's another similar improvement in tcp_cwnd_reduction().
Cc: Joe Perches <joe@perches.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If sch_fq is used at ingress, skbs that might have been
timestamped by net_timestamp_set() if a packet capture
is requesting timestamps could be delayed by arbitrary
amount of time, since sch_fq time base is MONOTONIC.
Fix this problem by moving code from sch_netem.c to act_mirred.c.
Fixes: fb420d5d91c1 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mv88e6161 would sometime fail to probe with a timeout waiting for
the switch to complete an operation. This operation is supposed to
clear the statistics counters. However, due to a read/modify/write,
without the needed mask, the operation actually carried out was more
random, with invalid parameters, resulting in the switch not
responding. We need to preserve the histogram mode bits, so apply a
mask to keep them.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 40cff8fca9e3 ("net: dsa: mv88e6xxx: Fix stats histogram mode")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 6390X family has 8 SERDES interfaces. When ports 9 and 10 are not
using all their SERDES interfaces, the unused ones can be assigned to
ports 2-8. Add support for interrupts from SERDES interfaces connected
to these lower ports.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 6390X family has 8 SERDES interfaces. This allows ports 9 and 10
to support up to 10Gbps using 4 SERDES interfaces. However, when lower
speeds are used, which need fewer SERDES interfaces, the unused SERDES
interfaces can be used by ports 2-8.
The hardware defaults to ports 9 and 10 having all 4 SERDES interfaces
assigned to them. This only gets changed when the interface is
configured after what the SFP supports has been determined, or the 10G
PHY completes auto-neg.
For hardware designs which limit ports 9 and 10 to one or two SERDES
interfaces, and place SFPs on the lower interfaces, this is too
late. Those ports with SFP should not wait until ports 9/10 are up in
order to get access to the SERDES interface. So change the default
configuration when the driver is initialised. Configure ports 9 and 10
to 1000BaseX, so they use a single SERDES interface, freeing up the
others. They can steal them back if they need them.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The X family variants support additional ports modes, for 10G
operation, which the non-X variants don't have. Add a port_set_cmode()
for non-X variants to enforce this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move .port_set_cmode next to .port_get_cmode.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that 2.5G and 5G can be represented in phydev->advertising and
phydev->lp_advertising, add these two links modes as possible
resolutions to auto negotiation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that PHYs and MAC can support more than 32 bit masks, add link
modes which are > 31 to the PHY settings table.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add missing markup for function parameters
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert phy drivers to report the link partner advertised modes using
a linkmode bitmap. This allows them to report the higher speeds which
don't fit in a u32.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both states aren't used. Most likely they result from an idea that
never materialized. So remove them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a link failure is detected locally, the link is reset, the flag
link->in_session is set to false, and a RESET_MSG with the 'stopping'
bit set is sent to the peer.
The purpose of this bit is to inform the peer that this endpoint just
is going down, and that the peer should handle the reception of this
particular RESET message as a local failure. This forces the peer to
accept another RESET or ACTIVATE message from this endpoint before it
can re-establish the link. This again is necessary to ensure that
link session numbers are properly exchanged before the link comes up
again.
If a failure is detected locally at the same time at the peer endpoint
this will do the same, which is also a correct behavior.
However, when receiving such messages, the endpoints will not
distinguish between 'stopping' RESETs and ordinary ones when it comes
to updating session numbers. Both endpoints will copy the received
session number and set their 'in_session' flags to true at the
reception, while they are still expecting another RESET from the
peer before they can go ahead and re-establish. This is contradictory,
since, after applying the validation check referred to below, the
'in_session' flag will cause rejection of all such messages, and the
link will never come up again.
We now fix this by not only handling received RESET/STOPPING messages
as a local failure, but also by omitting to set a new session number
and the 'in_session' flag in such cases.
Fixes: 7ea817f4e832 ("tipc: check session number before accepting link protocol messages")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The snmp_counter.rst explains the meanings of snmp counters. It also
provides a set of experiments (only 1 for this initial patch),
combines the experiments' resutls and the snmp counters'
meanings. This is an initial path, only explains a part of IP/ICMP
counters and provide a simple ping test.
Signed-off-by: yupeng <yupeng0921@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the broadcast retransmission algorithm is using the
'prev_retr' field in struct tipc_link to time stamp the latest broadcast
retransmission occasion. This helps to restrict retransmission of
individual broadcast packets to max once per 10 milliseconds, even
though all other criteria for retransmission are met.
We now move this time stamp to the control block of each individual
packet, and remove other limiting criteria. This simplifies the
retransmission algorithm, and eliminates any risk of logical errors
in selecting which packets can be retransmitted.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: LUU Duc Canh <canh.d.luu@dektech.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent changes to NFP mean that stats updates from fw to driver no longer
require a flow lookup and (because egdev offload has been removed) the
ingress netdev for a lookup is now always known.
Remove obsolete code in a flow lookup that matches on host context and
that allows for a netdev to be NULL.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, only tunnel decap rules required egdev registration for
offload in NFP. These are now supported via indirect TC block callbacks.
Remove the egdev code from NFP.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, TC block tunnel decap rules were only offloaded when a
callback was triggered through registration of the rules egress device.
This meant that the driver had no access to the ingress netdev and so
could not verify it was the same tunnel type that the rule implied.
Register tunnel devices for indirect TC block offloads in NFP, giving
access to new rules based on the ingress device rather than egress. Use
this to verify the netdev type of VXLAN and Geneve based rules and offload
the rules to HW if applicable.
Tunnel registration is done via a netdev notifier. On notifier
registration, this is triggered for already existing netdevs. This means
that NFP can register for offloads from devices that exist before it is
loaded (filter rules will be replayed from the TC core). Similarly, on
notifier unregister, a call is triggered for each currently active netdev.
This allows the driver to unregister any indirect block callbacks that may
still be active.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both the actions and tunnel_conf files contain local functions that check
the type of an input netdev. In preparation for re-use with tunnel offload
via indirect blocks, move these to static inline functions in a header
file.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously the offload functions in NFP assumed that the ingress (or
egress) netdev passed to them was an nfp repr.
Modify the driver to permit the passing of non repr netdevs as the ingress
device for an offload rule candidate. This may include devices such as
tunnels. The driver should then base its offload decision on a combination
of ingress device and egress port for a rule.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently drivers can register to receive TC block bind/unbind callbacks
by implementing the setup_tc ndo in any of their given netdevs. However,
drivers may also be interested in binds to higher level devices (e.g.
tunnel drivers) to potentially offload filters applied to them.
Introduce indirect block devs which allows drivers to register callbacks
for block binds on other devices. The callback is triggered when the
device is bound to a block, allowing the driver to register for rules
applied to that block using already available functions.
Freeing an indirect block callback will trigger an unbind event (if
necessary) to direct the driver to remove any offloaded rules and unreg
any block rule callbacks. It is the responsibility of the implementing
driver to clean any registered indirect block callbacks before exiting,
if the block it still active at such a time.
Allow registering an indirect block dev callback for a device that is
already bound to a block. In this case (if it is an ingress block),
register and also trigger the callback meaning that any already installed
rules can be replayed to the calling driver.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use new macros for PHYID matching to avoid boilerplate code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add macros for PHYID matching to be used in PHY driver configs.
By using these macros some boilerplate code can be avoided.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that phy_mac_interrupt() doesn't call phy_change() any longer it's
called from phy_interrupt() only. Therefore phy_interrupt_is_valid()
returns true always and the check can be removed.
In case of PHY_HALTED phy_interrupt() bails out immediately,
therefore the second check for PHY_HALTED including the call to
phy_disable_interrupts() can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using phy_mac_interrupt() the irq number is set to
PHY_IGNORE_INTERRUPT, therefore phy_interrupt_is_valid() returns false.
As a result phy_change() effectively just calls phy_trigger_machine()
when called from phy_mac_interrupt() via phy_change_work(). So we can
call phy_trigger_machine() from phy_mac_interrupt() directly and
remove some now unneeded code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
State PHY_CHANGELINK isn't needed here, we can call the state machine
directly. We just have to remove the check for phy_polling_mode() to
make this work also in interrupt mode. Removing this check doesn't
cause any overhead because when not polling the state machine is
called only if required by some event.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that flag PHY_HAS_INTERRUPT has been replaced with a check for
callbacks config_intr and ack_interrupt, we can remove setting this
flag from all driver configs.
Last but not least remove flag PHY_HAS_INTERRUPT completely.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Flag PHY_HAS_INTERRUPT is used only here for this small check. I think
using interrupts isn't possible if a driver defines neither
config_intr nor ack_interrupts callback. So we can replace checking
flag PHY_HAS_INTERRUPT with checking for these callbacks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 37c8a5fafa3b ("kbuild: consolidate Devicetree dtb build rules")
moved the location of 'dtbs_install' target which caused dtbs to not be
installed when building debian package with 'bindeb-pkg' target. Update
the builddeb script to use the same logic that determines if there's a
'dtbs_install' target which is presence of the arch dts directory. Also,
use CONFIG_OF_EARLY_FLATTREE instead of CONFIG_OF as that's a better
indication of whether we are building dtbs.
This commit will also have the side effect of installing dtbs on any
arch that has dts files. Previously, it was dependent on whether the
arch defined 'dtbs_install'.
Fixes: 37c8a5fafa3b ("kbuild: consolidate Devicetree dtb build rules")
Reported-by: Nuno Gonçalves <nunojpg@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This reverts commit 6147b1cf19651c7de297e69108b141fb30aa2349.
The reverted patch results in attempted write access to the source
repository, even if that repository is mounted read-only.
Output from "strace git status -uno --porcelain":
getcwd("/tmp/linux-test", 129) = 16
open("/tmp/linux-test/.git/index.lock", O_RDWR|O_CREAT|O_EXCL|O_CLOEXEC, 0666) =
-1 EROFS (Read-only file system)
While git appears to be able to handle this situation, a monitored
build environment (such as the one used for Chrome OS kernel builds)
may detect it and bail out with an access violation error. On top of
that, the attempted write access suggests that git _will_ write to the
file even if a build output directory is specified. Users may have the
reasonable expectation that the source repository remains untouched in
that situation.
Fixes: 6147b1cf19651 ("scripts/setlocalversion: git: Make -dirty check more robust"
Cc: Genki Sky <sky@genki.is>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Since commit b41d920acff8 ("kbuild: deb-pkg: split generating packaging
and build"), the build version of the kernel contained in a deb package
is too low by 1.
Prior to the bad commit, the kernel was built first, then the number
in .version file was read out, and written into the debian control file.
Now, the debian control file is created before the kernel is actually
compiled, which is causing the version number mismatch.
Let the mkdebian script pass KBUILD_BUILD_VERSION=${revision} to require
the build system to use the specified version number.
Fixes: b41d920acff8 ("kbuild: deb-pkg: split generating packaging and build")
Reported-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Doug Smythies <dsmythies@telus.net>
|
|
The current SED_CONFIG_EXP could match to comment lines in config
fragment files, especially when CONFIG_PREFIX_ is empty. For example,
Buildroot uses empty prefixing; starting symbols with BR2_ is just
convention.
Make the sed expression more robust against false positives from
comment lines. The new sed expression matches to only valid patterns.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Petr Vorel <petr.vorel@gmail.com>
Reviewed-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
|
|
Same change as made to sctp_intl_store_reasm().
To be fully correct, an iterator has an undefined value when something
like skb_queue_walk() naturally terminates.
This will actually matter when SKB queues are converted over to
list_head.
Formalize what this code ends up doing with the current
implementation.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To be fully correct, an iterator has an undefined value when something
like skb_queue_walk() naturally terminates.
This will actually matter when SKB queues are converted over to
list_head.
Formalize what this code ends up doing with the current
implementation.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eliminate the assumption that SKBs and SKB list heads can
be cast to eachother in SKB list handling code.
This change also appears to fix a bug since the list->next pointer is
sampled outside of holding the SKB queue lock.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of direct SKB list pointer accesses.
The loops in this function had to be rewritten to accommodate this
more easily.
The first loop iterates now over the target list in the outer loop,
and triggers an mmc data operation when the per-operation limits are
hit.
Then after the loops, if we have any residue, we trigger the last
and final operation.
For the page aligned workaround, where we have to copy the read data
back into the original list of SKBs, we use a two-tiered loop. The
outer loop stays the same and iterates over pktlist, and then we have
an inner loop which uses skb_peek_next(). The break logic has been
simplified because we know that the aggregate length of the SKBs in
the source and destination lists are the same.
This change also ends up fixing a bug, having to do with the
maintainance of the seg_sz variable and how it drove the outermost
loop. It begins as:
seg_sz = target_list->qlen;
ie. the number of packets in the target_list queue. The loop
structure was then:
while (seq_sz) {
...
while (not at end of target_list) {
...
sg_cnt++
...
}
...
seg_sz -= sg_cnt;
The assumption built into that last statement is that sg_cnt counts
how many packets from target_list have been fully processed by the
inner loop. But this not true.
If we hit one of the limits, such as the max segment size or the max
request size, we will break and copy a partial packet then contine
back up to the top of the outermost loop.
With the new loops we don't have this problem as we don't guard the
loop exit with a packet count, but instead use the progression of the
pkt_next SKB through the list to the end. The general structure is:
sg_cnt = 0;
skb_queue_walk(target_list, pkt_next) {
pkt_offset = 0;
...
sg_cnt++;
...
while (pkt_offset < pkt_next->len) {
pkt_offset += sg_data_size;
if (queued up max per request)
mmc_submit_one();
}
}
if (sg_cnt)
mmc_submit_one();
The variables that maintain where we are in the MMC command state such
as req_sz, sg_cnt, and sgl are reset when we emit one of these full
sized requests.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It turns out I missed one VLAN_TAG_PRESENT in OVS code while rebasing.
This fixes it.
Fixes: 9df46aefafa6 ("OVS: remove use of VLAN_TAG_PRESENT")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TCA_FLOWER_KEY_ENC_OPTS and TCA_FLOWER_KEY_ENC_OPTS_MASK can only
currently contain further nested attributes, which are parsed by
hand, so the policy is never actually used resulting in a W=1
build warning:
net/sched/cls_flower.c:492:1: warning: ‘enc_opts_policy’ defined but not used [-Wunused-const-variable=]
enc_opts_policy[TCA_FLOWER_KEY_ENC_OPTS_MAX + 1] = {
Add the validation anyway to avoid potential bugs when other
attributes are added and to make the attribute structure slightly
more clear. Validation will also set extact to point to bad
attribute on error.
Fixes: 0a6e77784f49 ("net/sched: allow flower to match tunnel options")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following:
skb = skb->next;
...
if (skb == (struct sk_buff *)queue)
is transformed into:
skb = skb_peek_next(skb, queue);
...
if (!skb)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The phy core provides a handy phy_speed_to_str() helper, so use that
instead of doing our own formatting of the different known link speeds.
To do this, increase PHY_LED_TRIGGER_SPEED_SUFFIX_SIZE to 11 so we can fit
'Unsupported' if necessary.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As a heritage from the very early days of phylib member interrupts is
defined as u32 even though it's just a flag whether interrupts are
enabled. So we can change it to a bitfield member. In addition change
the code dealing with this member in a way that it's clear we're
dealing with a bool value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The reserved variable should be named reserved1.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The fsl_mc_portal_allocate can fail when the requested MC portals are
not yet probed by the fsl_mc_allocator. In this situation, the driver
should defer the probe.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Heiner Kallweit
Eric Dumazet
Yafang Shao
Andrew Lunn
Jon Maloy
yupeng
LUU Duc Canh
John Hurley
Rob Herring
Guenter Roeck
Masahiro Yamada
David S. Miller
Michał Mirosław
Jakub Kicinski
Kyle Roeschley
Alexandre Belloni
Ioana Ciornei