| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
spi_nor_spansion_clear_sr_bp() depends on spansion_quad_enable().
While spansion_quad_enable() is selected as default when
initializing the flash parameters, the nor->quad_enable() method
can be overwritten later on when parsing BFPT.
Select the write protection disable mechanism at spi_nor_init() time,
when the nor->quad_enable() method is already known.
Fixes: 191f5c2ed4b6faba ("mtd: spi-nor: use 16-bit WRR command when QE is set on spansion flashes")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Pull MTD updates from Miquel Raynal:
"This contains the following changes for MTD:
MTD core changes:
- New Hyperbus framework
- New _is_locked (concat) implementation
- Various cleanups
NAND core changes:
- use longest matching pattern in ->exec_op() default parser
- export NAND operation tracer
- add flag to indicate panic_write in MTD
- use kzalloc() instead of kmalloc() and memset()
Raw NAND controller drivers changes:
- brcmnand:
- fix BCH ECC layout for large page NAND parts
- fallback to detected ecc-strength, ecc-step-size
- when oops in progress use pio and interrupt polling
- code refactor code to introduce helper functions
- add support for v7.3 controller
- FSMC:
- use nand_op_trace for operation tracing
- GPMI:
- move all driver code into single file
- various cleanups (including dmaengine changes)
- use runtime PM to manage clocks
- implement exec_op
- MTK:
- correct low level time calculation of r/w cycle
- improve data sampling timing for read cycle
- add validity check for CE# pin setting
- fix wrongly assigned OOB buffer pointer issue
- re-license MTK NAND driver as Dual MIT/GPL
- STM32:
- manage the get_irq error case
- increase DMA completion timeouts
Raw NAND chips drivers changes:
- Macronix: add read-retry support
Onenand driver changes:
- add support for 8Gb datasize chips
- avoid fall-through warnings
SPI-NAND changes:
- define macros for page-read ops with three-byte addresses
- add support for two-byte device IDs and then for GigaDevice
GD5F1GQ4UFxxG
- add initial support for Paragon PN26G0xA
- handle the case where the last page read has bitflips
SPI-NOR core changes:
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control"
* tag 'mtd/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (60 commits)
mtd: concat: implement _is_locked mtd operation
mtd: concat: refactor concat_lock/concat_unlock
mtd: abi: do not use C++ style comments in uapi header
mtd: afs: remove unneeded NULL check
mtd: rawnand: stm32_fmc2: increase DMA completion timeouts
mtd: rawnand: Use kzalloc() instead of kmalloc() and memset()
mtd: hyperbus: Add driver for TI's HyperBus memory controller
mtd: spinand: read returns badly if the last page has bitflips
mtd: spinand: Add initial support for Paragon PN26G0xA
mtd: rawnand: mtk: Re-license MTK NAND driver as Dual MIT/GPL
mtd: rawnand: gpmi: remove double assignment to block_size
dt-bindings: mtd: brcmnand: Add brcmnand, brcmnand-v7.3 support
mtd: rawnand: brcmnand: Add support for v7.3 controller
mtd: rawnand: brcmnand: Refactored code to introduce helper functions
mtd: rawnand: brcmnand: When oops in progress use pio and interrupt polling
mtd: Add flag to indicate panic_write
mtd: rawnand: Add Macronix NAND read retry support
mtd: onenand: Avoid fall-through warnings
mtd: spinand: Add support for GigaDevice GD5F1GQ4UFxxG
mtd: spinand: Add support for two-byte device IDs
...
|
|
SPI-NOR core changes:
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control
|
|
Get the reset control properties for the QSPI controller and bring them
out of reset. Most will have just one reset bit, but there is an additional
OCP reset bit that is used ECC. The OCP reset bit will also need to get
de-asserted as well. [1]
The reason this patch is needed is in the case where a bootloader leaves
the QSPI controller in a reset state, or a state where init cannot occur
successfully, the patch will put the QSPI controller into a clean state.
[1] https://www.intel.com/content/www/us/en/programmable/hps/arria-10/hps.html#reg_soc_top/sfo1429890575955.html
Suggested-by: Tien-Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
[tudor.ambarus@microchip.com: declare rstc and rstc_ocp on the same line]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
IS25LP256 gets BFPT_DWORD1_ADDRESS_BYTES_3_ONLY from BFPT table for
address width. But in actual fact the flash can support 4-byte address.
Use a post bfpt fixup hook to overwrite the address width advertised by
the BFPT.
Signed-off-by: Liu Xiang <liu.xiang6@zte.com.cn>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Pull mtd fixes from Miquel Raynal:
- Set the raw NAND number of targets to the right value
- Fix a bug uncovered by a recent patch on Spansion SPI-NOR flashes
* tag 'mtd/fixes-for-5.2-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: spi-nor: use 16-bit WRR command when QE is set on spansion flashes
mtd: rawnand: initialize ntargets with maxchips
|
|
SPI memory devices from different manufacturers have widely
different configurations for Status, Control and Configuration
registers. JEDEC 216C defines a new map for these common register
bits and their functions, and describes how the individual bits may
be accessed for a specific device. For the JEDEC 216B compliant
flashes, we can partially deduce Status and Configuration registers
functions by inspecting the 16th DWORD of BFPT. Older flashes that
don't declare the SFDP tables (SPANSION FL512SAIFG1 311QQ063 A ©11
SPANSION) let the software decide how to interact with these registers.
The commit dcb4b22eeaf4 ("spi-nor: s25fl512s supports region locking")
uncovered a probe error for s25fl512s, when the Quad Enable bit CR[1]
was set to one in the bootloader. When this bit is one, only the Write
Status (01h) command with two data byts may be used, the 01h command with
one data byte is not recognized and hence the error when trying to clear
the block protection bits.
Fix the above by using the Write Status (01h) command with two data bytes
when the Quad Enable bit is one.
Backward compatibility should be fine. The newly introduced
spi_nor_spansion_clear_sr_bp() is tightly coupled with the
spansion_quad_enable() function. Both assume that the Write Register
with 16 bits, together with the Read Configuration Register (35h)
instructions are supported.
Fixes: dcb4b22eeaf44f91 ("spi-nor: s25fl512s supports region locking")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Jonas Bonn <jonas@norrbonn.se>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
This gets rid of the license boilerplate duplicated in each file.
No functional changes intended.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Intel Elkhart Lake has the same SPI serial flash controller as Ice Lake.
Add Elkhart Lake PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Testing done on Mikrotik Routerboard RB450Gx4 board under
4.14.119 and 4.19.43 kernels. The test board does not support
Dual or Quad modes.
Datasheet at:
https://www.winbond.com/resource-files/w25q16jv%20spi%20revg%2003222018%20plus.pdf
Signed-off-by: Robert Marko <robimarko@gmail.com>
[tudor.ambarus@microchip.com: w25q16jv-im/jm and w25q16jv-iq/jq
have different jedec ids, fix flash name.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 503 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.811534538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In case of SPI error during the reading of the nor Id,
the probe fails without any error message related to
the JEDEC Id reading procedure.
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Add an entry for Micron MT25QL02 which is a 3V variant of already
supported MT25QU02.
Testing was done on a ZII VF610 Dev Board (rev. B).
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
[tudor.ambarus@microchip.com: order entry alphabetically, wrap to
80 chars limit]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
There's a new driver using the SPI memory interface of the
SPI framework at spi/spi-stm32-qspi.c, which can be used
together with m25p80.c to replace the functionality of
this SPI NOR driver.
The "new" driver uses the same dt properties and not affects
the legacy compatibility.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Intel Comet Lake has the same SPI serial flash controller as Ice Lake.
Add Comet Lake PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Both the BP[0-2] bits and the TBPROT bit are supported on this chip.
Tested and verified on a Cypress s25fl512s.
Signed-off-by: Jonas Bonn <jonas@norrbonn.se>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
It was observed that reads crossing 4K address boundary are failing.
This limitation is mentioned in Intel documents:
Intel(R) 9 Series Chipset Family Platform Controller Hub (PCH) Datasheet:
"5.26.3 Flash Access
Program Register Access:
* Program Register Accesses are not allowed to cross a 4 KB boundary..."
Enhanced Serial Peripheral Interface (eSPI)
Interface Base Specification (for Client and Server Platforms):
"5.1.4 Address
For other memory transactions, the address may start or end at any byte
boundary. However, the address and payload length combination must not
cross the naturally aligned address boundary of the corresponding Maximum
Payload Size. It must not cross a 4 KB address boundary."
Avoid this by splitting an operation crossing the boundary into two
operations.
Fixes: 8afda8b26d01 ("spi-nor: Add support for Intel SPI serial flash controller")
Cc: stable@vger.kernel.org
Reported-by: Romain Porte <romain.porte@nokia.com>
Tested-by: Pascal Fabreges <pascal.fabreges@nokia.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Erase types are sorted *smallest* type first, refer to
spi_nor_sort_erase_mask().
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
If identification of an SPI NOR FLASH fails, the JEDEC ID is printed,
which is stored in the first 3 bytes of the ID read from the FLASH.
However, the extended JEDEC ID, which is stored in the remaining bytes,
also matters, as it is used for identification of some FLASH types.
Print all (currently 6) ID bytes read to ease failure analysis and
debugging.
Suggested-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Pull spi updates from Mark Brown:
"A fairly quiet release for SPI, the biggest thing is the conversion to
use GPIO descriptors which is now 90% done but still needs some
stragglers converting.
Summary:
- Support for inter-word delays
- Conversion of the core and most drivers to use GPIO descriptors for
GPIO controlled chip selects
- New drivers for NXP FlexSPI and QuadSPI, SiFive and Spreadtrum"
* tag 'spi-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (104 commits)
spi: sh-msiof: Restrict bits per word to 8/16/24/32 on R-Car Gen2/3
spi: sifive: Remove redundant dev_err call in sifive_spi_probe()
spi: sifive: Remove spi_master_put in sifive_spi_remove()
spi: spi-gpio: fix SPI_CS_HIGH capability
spi: pxa2xx: Setup maximum supported DMA transfer length
spi: sifive: Add driver for the SiFive SPI controller
spi: sifive: Add DT documentation for SiFive SPI controller
spi: sprd: Add a prefix for SPI DMA channel macros
spi: sprd: spi: sprd: Add DMA mode support
dt-bindings: spi: Add the DMA properties for the SPI dma mode
spi: sprd: Add the SPI irq function for the SPI DMA mode
dt-bindings: spi: imx: Add an entry for the i.MX8QM compatible
spi: use gpio[d]_set_value_cansleep for setting chipselect GPIO
spi: gpio: Advertise support for SPI_CS_HIGH
spi: sh-msiof: Replace spi_master by spi_controller
spi: sh-hspi: Replace spi_master by spi_controller
spi: rspi: Replace spi_master by spi_controller
spi: atmel-quadspi: add support for sam9x60 qspi controller
dt-bindings: spi: atmel-quadspi: QuadSPI driver for Microchip SAM9X60
spi: atmel-quadspi: add support for named peripheral clock
...
|
|
There is a spelling mistake in a dev_error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
|
|
The Eon EN25QH64 is a 64 Mbit SPI NOR flash memory chip found
on recent wireless routers. Its 32, 128 and 256 Mbit siblings
are already supported.
Tested on a COMFAST CF-E120A v3 router board.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
|
|
This adds support for the Macronix MX25V8035F, a 8Mb SPI NOR chip.
It is used on i.MX6UL/ULL SoMs by Kontron Electronics GmbH (N631x).
It was only tested with a single data line connected, by writing and
reading random data with dd.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
|
|
This adds support for the EON EN25Q80A, a 8Mb SPI NOR chip.
It is used on i.MX6 boards by Kontron Electronics GmbH
(N60xx, N61xx).
It was only tested with a single data line connected, by writing and
reading random data with dd.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
|
|
Cadence OSPI controller IP supports Octal IO (x8 IO lines),
It also has an integrated PHY. IP register layout is very
similar to existing QSPI IP except for additional bits to support Octal
and Octal DDR mode. Therefore, extend current driver to support Octal
mode. Only Octal SDR read (1-1-8)mode is supported for now.
Tested with mt35xu512aba Octal flash on TI's AM654 EVM.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
|
|
Due to two different versions (S25FL128SAGBHI200 and S25FL128SAGBHI210) of
the s25fl128s qspi memory, the single "s25fl128s" device entry must be
split into two to match the correct JEDEC ID's for each version. Solves
paging related issues of S25FL128SAGBHI210 chips.
Signed-off-by: Ahmet Celenk <ahmet.celenk@procenne.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
|
|
cadence-quadspi controller allows upto eight bytes of data to
be written in software Triggered Instruction generator (STIG) mode
of operation. Lower 4 bytes are written through writedatalower and
upper 4 bytes by writedataupper register.
This patch allows all the 8 bytes to be written.
Signed-off-by: Purna Chandra Mandal <purna.chandra.mandal@intel.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
|
|
The mx25u3235f is found on the ZyXEL NBG6817 router, therefore
add driver support for it so that we can upstream board support.
Minimal tested with u-boot tools fw_printenv/fw_setenv on GlobalScale
ESPRESSObin v5 board.
Signed-off-by: André Valentin <avalentin@marcant.net>
[miyatsu@qq.com: Remove unnecessary white space.]
Signed-off-by: Ding Tao <miyatsu@qq.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
|
|
Spansion S25FL512S ID is erroneously using 5-byte JEDEC ID, while the chip
family ID is stored in the 6th byte. Due to using only 5-byte ID, it's also
covering S25FS512S and now that we have added 6-byte ID for that chip, we
can convert S25FL512S to using a proper 6-byte ID as well...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
|
|
Spansion S25FS512S flash is currently misdetected as S25FL512S since the
latter uses 5-byte JEDEC ID, while the 6th ID byte (family ID) is different
on those chips. Add the 6-byte S25FS512S ID before S25FL512S ID in order
not to break the existing S25FS512S users.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
|
|
Add octal read flag for flash mt35xu512aba.
This flash, mt35xu512aba, is only complaint to SFDP JESD216B and does
not seem to support newer JESD216C standard that provides auto
detection of Octal mode capabilities and opcodes. Therefore, this
capability is manually added using new SPI_NOR_OCTAL_READ flag.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
|
|
- Add opcodes for octal I/O commands
* Read : 1-1-8 and 1-8-8 protocol
* Write : 1-1-8 and 1-8-8 protocol
* opcodes for 4-byte address mode command
- Entry of macros in _convert_3to4_xxx function
- Add flag SPI_NOR_OCTAL_READ specifying flash support octal read
commands. This flag is required for flashes which didn't provides
support for auto detection of Octal mode capabilities i.e. not
seems to support newer JESD216C standard.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
|
|
The quadspi is a generic communication interface which could be shared
with other MediaTek SoCs. Hence rename it to a common one.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
|
|
SNOR_HWCAPS_READ should be supported by this controller, so add this
flag to spi_nor_hwcaps mask.
Signed-off-by: Guochun Mao <guochun.mao@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
|
|
There's a new driver using the SPI memory interface of the SPI framework
at spi/spi-fsl-qspi.c, which can be used together with m25p80.c to
replace the functionality of this SPI NOR driver.
The new driver is already in use and this code is not compiled anymore,
so let's remove it.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Han Xu <han.xu@nxp.com>
Tested-by: Han Xu <han.xu@nxp.com>
Acked-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This driver is derived from the SPI NOR driver at
mtd/spi-nor/fsl-quadspi.c. It uses the new SPI memory interface
of the SPI framework to issue flash memory operations to up to
four connected flash chips (2 buses with 2 CS each).
The controller does not support generic SPI messages.
This patch also disables the build of the "old" driver and reuses
its Kconfig option CONFIG_SPI_FSL_QUADSPI to replace it.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Tested-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Tested-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Pull spi updates from Mark Brown:
"The main thing this release has been a lot of work on the integration
with SPI NOR flashes, there's been some specific support for a while
for controller features designed to make them perform better but it's
not worked out as well as hoped so the interface has been redesigned
in a way that will hopefully do better - it's already been adopted by
a number of additional controllers so things are looking good.
Otherwise most of the work has been driver specific:
- Support for better integration with NOR flashes from Boris
Brezillon and Yogesh Narayan Gaur plus usage of it in several
drivers.
- A big cleanup of the Rockchip driver from Emil Renner Berthing.
- Lots of performance improvements for bcm2835 from Lukas Wunner.
- Slave mode support for pxa2xx from Lubomir Rintel.
- Support for Macronix MXIC, Mediatek MT7629 and MT8183, NPCM PSPI,
and Renesas r8a77470"
* tag 'spi-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (90 commits)
spi: sh-msiof: Reduce the number of times write to and perform the transmission from FIFO
spi: sh-msiof: Add r8a774c0 support
doc: lpspi: Document DT bindings for LPSPI slave mode
spi: lpspi: Let watermark change with send data length
spi: lpspi: Add slave mode support
spi: lpspi: Replace all "master" with "controller"
spi: imx: drop useless member speed_hz from driver data struct
spi: imx: rename config callback and add useful parameters
spi: imx: style fixes
spi: imx: mx51-ecspi: Move some initialisation to prepare_message hook.
spi: imx: add a device specific prepare_message callback
mtd: atmel-quadspi: disallow building on ebsa110
spi: Update NPCM PSPI controller documentation
spi: npcm: Modify pspi send function
spi: Use of_node_name_eq for node name comparisons
spi: dw-mmio: add ACPI support
spi: bcm2835: Synchronize with callback on DMA termination
spi: bcm2835: Speed up FIFO access if fill level is known
spi: bcm2835: Polish transfer of DMA prologue
spi: spi-mem: add support for octal mode I/O data transfer
...
|
|
|
|
The is25lp016d is found on the iwg23s from iWave, therefore
add driver support for it so that we can upstream board support.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
Add support for SFDP (JESD216B) 4-byte Address Instruction Table. This
table is optional but when available, we parse it to get the 4-byte
address op codes supported by the memory.
Using these op codes is stateless as opposed to entering the 4-byte
address mode or setting the Base Address Register (BAR).
Flashes that have the 4BAIT table declared can now support
SPINOR_OP_PP_1_1_4_4B and SPINOR_OP_PP_1_4_4_4B opcodes.
Tested on MX25L25673G.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@microchip.com>
[tudor.ambarus@microchip.com:
- rework erase and page program logic,
- pass DMA-able buffer to spi_nor_read_sfdp(),
- introduce SPI_NOR_HAS_4BAIT
- various minor updates.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
The is25lp256 supports 4-byte opcodes and quad output.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Liu Xiang <liu.xiang6@zte.com.cn>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
Add SPDX tags to replace the license boiler-plate and fix the
MODULE_LICENSE() definition in spi-nor.c to match the license text
(GPL v2).
Interestingly, spi-nor.h and spi-nor.c do not use the same license
(GPL v2+ for spi-nor.h, GPL v2 for spi-nor.c).
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
No need to use an integer when the value is either true or false.
Make it a boolean.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
Tudor Ambarus
Linus Torvalds
Miquel Raynal
Dinh Nguyen
Liu Xiang
Mika Westerberg
Geert Uytterhoeven
Robert Marko
Thomas Gleixner
Flavio Suligoi
Andrey Smirnov
Ludovic Barre
Jonas Bonn
Alexander Sverdlin
Colin Ian King
Roger Pueyo Centelles
Frieder Schrempf
Vignesh R
Ahmet Celenk
Purna Chandra Mandal
André Valentin
Sergei Shtylyov
Yogesh Narayan Gaur
Ryder Lee
Guochun Mao
Mark Brown
Fabrizio Castro
Cyrille Pitchen
Boris Brezillon