| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This reverts commit a121f643993474548fe98144514c50dd4f3dbe76.
Unfortunately, this commit breaks UBIFS backward compatibility and
makes new UBIFS refuse older UBIFS-formatted media:
UBIFS error: validate_sb: min. I/O unit mismatch: 8 in superblock, 64 real
Thus, we have to revert this patch and work on a better solution.
Reported-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
* git://git.infradead.org/mtd-2.6: (59 commits)
mtd: mtdpart: disallow reading OOB past the end of the partition
mtd: pxa3xx_nand: NULL dereference in pxa3xx_nand_probe
UBI: use mtd->writebufsize to set minimal I/O unit size
mtd: initialize writebufsize in the MTD object of a partition
mtd: onenand: add mtd->writebufsize initialization
mtd: nand: add mtd->writebufsize initialization
mtd: cfi: add writebufsize initialization
mtd: add writebufsize field to mtd_info struct
mtd: OneNAND: OMAP2/3: prevent regulator sleeping while OneNAND is in use
mtd: OneNAND: add enable / disable methods to onenand_chip
mtd: m25p80: Fix JEDEC ID for AT26DF321
mtd: txx9ndfmc: limit transfer bytes to 512 (ECC provides 6 bytes max)
mtd: cfi_cmdset_0002: add support for Samsung K8D3x16UxC NOR chips
mtd: cfi_cmdset_0002: add support for Samsung K8D6x16UxM NOR chips
mtd: nand: ams-delta: drop omap_read/write, use ioremap
mtd: m25p80: add debugging trace in sst_write
mtd: nand: ams-delta: select for built-in by default
mtd: OneNAND: lighten scary initial bad block messages
mtd: OneNAND: OMAP2/3: add support for command line partitioning
mtd: nand: rearrange ONFI revision checking, add ONFI 2.3
...
Fix up trivial conflict in drivers/mtd/Kconfig as per DavidW.
|
|
Previously we used mtd->writesize field to set UBI's minimal
I/O unit size. This sometimes caused UBIFS recovery issues
when mounting an uncleanly unmounted UBIFS partition on NOR
flash since mtd->writesize is 1 byte for NOR flash. The
MTD CFI driver however often performs writing multiple
bytes in one programming operation using the chip's write
buffer. We have to use the size of this write buffer as
a minimal I/O unit size for UBI on NOR flash to fix the
observed UBIFS recovery issues.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
My new shiny code for corrupted PEB detection has NOR specific bug.
We tread PEB as corrupted and preserve it, if
1. EC header is OK.
2. VID header is corrupted.
3. data area is not "all 0xFFs"
In case of NOR we have 'nor_erase_prepare()' quirk, which invalidates
the headers before erasing the PEB. And we invalidate first the VID
header, and then the EC header. So if a power cut happens after we have
invalidated the VID header, but before we have invalidated the EC
header, we end up with a PEB which satisfies the above 3 conditions,
and the scanning code will treat it as corrupted, and will print
scary warnings, wrongly.
This patch fixes the issue by firt invalidating the EC header, then
invalidating the VID header. In case of power cut inbetween, we still
just lose the EC header, and UBI can deal with this situation gracefully.
Thanks to Anatolij Gustschin <agust@denx.de> for tracking this down.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Reported-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Anatolij Gustschin <agust@denx.de>
|
|
Commit 45aafd32996e27 "UBI: tighten the corrupted PEB criteria"
introduced some return paths that didn't release the ubi->buf_mutex
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: tighten the corrupted PEB criteria
UBI: fix check_data_ff return code
UBI: remember copy_flag while scanning
UBI: preserve corrupted PEBs
UBI: add truly corrupted PEBs to corrupted list
UBI: introduce debugging helper function
UBI: make check_pattern function non-static
UBI: do not put eraseblocks to the corrupted list unnecessarily
UBI: separate out corrupted list
UBI: change cascade of ifs to switch statements
UBI: rename a local variable
UBI: handle bit-flips when no header found
UBI: remove duplicate IO error codes
UBI: rename IO error code
UBI: fix small 80 characters limit style issue
UBI: cleanup and simplify Kconfig
|
|
If we get a bit-flip of ECC error while reading the data area, do not add it to
corrupted list, because it is possible that this is just unstable PEB with
corruptions caused by unclean reboots.
This patch also improves commentaries.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
When the data does not contain all 0xFF bytes, 'check_data_ff()' should return
1, not -EINVAL; Also, the caller ('process_eb()') should not add the PEB to the
"corrupted" list if there was a read error.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
While scanning the flash we read all VID headers and store some important
information in 'struct ubi_scan_leb'. Store also the 'copy_flag' value there
as it is needed when comparing LEBs. We do not increase memory consumption
because this is just one bit and we have plenty of spare bits in
'struct ubi_scan_leb' (sizeof(struct ubi_scan_leb) is 48 both with and
without this patch).
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Currently UBI erases all corrupted eraseblocks, irrespectively of the nature
of corruption: corruption due to power cuts and non-power cut corruption.
The former case is OK, but the latter is not, because UBI may destroy
potentially important data.
With this patch, during scanning, when UBI hits a PEB with corrupted VID
header, it checks whether this PEB contains only 0xFF data. If yes, it is
safe to erase this PEB and it is put to the 'erase' list. If not, this may
be important data and it is better to avoid erasing this PEB. Instead,
UBI puts it to the corr list and moves out of the pool of available PEB.
IOW, UBI preserves this PEB.
Such corrupted PEB lessen the amount of available PEBs. So the more of them
we accumulate, the less PEBs are available. The maximum amount of non-power
cut corrupted PEBs is 8.
This patch is a response to UBIFS problem where reporter
(Matthew L. Creech <mlcreech@gmail.com>) observes that UBIFS index points
to an unmapped LEB. The theory is that corresponding PEB somehow got
corrupted and UBI wiped it. This patch (actually a series of patches)
tries to make sure such PEBs are preserved - this would make it is easier
to analyze the corruption.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Start using the 'corr' list and add there PEBs which look truly corrupted,
which means they have corrupted VID header and the data which follows the
corrupted header does not contain all 0xFF bytes.
At the moment, this does not change UBI functionality much because these
PEBs will be erase when scanning finishes. But the plan is to teach UBI
preserving them.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Introduce a helper function to print hexdump: 'ubi_dbg_print_hex_dump()'.
It is compiled out if debugging is enabled. Will be used in the next patch.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
This patch turns static function 'check_pattern()' into a non-static
'ubi_check_pattern()'. This is just a preparation for the chages which
are coming in the next patches.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Currently UBI maintains 2 lists of PEBs during scanning:
1. 'erase' list - PEBs which have no corruptions but should be erased
2. 'corr' list - PEBs which have some corruptions and should be erased
But we do not really need 2 lists for PEBs which should be erased after
scanning is done - this is redundant. So this patch makes sure all PEBs
which are corrupted are moved to the head of the 'erase' list. We add
them to the head to make sure they are erased first and we get rid of
corruption ASAP.
However, we do not remove the 'corr' list and realted functions, because
the plan is to use this list for other purposes. Namely, we plan to
put eraseblocks with corruption which does not look like it was caused
by unclean power cut. Then we'll preserve thes PEBs in order to avoid
killing potentially valuable user data.
This patch also amends PEBs accounting, because it was closely tight to
the 'erase'/'corr' lists separation.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
This patch introduces 'add_corrupted()' function and separates out 'corr' list
manipulation from the common 'add_to_list()' function. This is just a
preparation for further changes - this patch does not change functionality.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
This patch improves readability and simplifies scanning code by changing a
long cascade of 'if' statements to a switch statement. This should presumably
be a little faster as well.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Rename local variable 'ec_corr' into 'ec_err' to make the code a little bit
more readable. 'ec_err' is more appropriate because it sounds more like 'error
when EC was read' and it looks more logical because we use it together with
'err'. Just a minor nicification which should improve the rather complex
scanning code.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Currently UBI has one small flaw - when we read EC or VID header, but find only
0xFF bytes, we return UBI_IO_FF and do not report whether we had bit-flips or
not. In case of the VID header, the scanning code adds this PEB to the free list,
even though there were bit-flips.
Imagine the following situation: we start writing VID header to a PEB and have a
power cut, so the PEB becomes unstable. When we scan and read the PEB, we get
a bit-flip. Currently, UBI would just ignore this and treat the PEB as free. This
patch changes UBI behavior and now UBI will schedule this PEB for erasure.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
The 'UBI_IO_PEB_EMPTY' and 'UBI_IO_PEB_FREE' are essentially the same
and mean that there are only 0xFF bytes instead of headers. Simplify
UBI a little by turning them into a single 'UBI_IO_FF' error code.
Also, stop maintaining commentaries in 'ubi_io_read_vid_hdr()' which are
almost identical to commentaries in 'ubi_io_read_ec_hdr()'.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Rename UBI_IO_BAD_HDR_READ into UBI_IO_BAD_HDR_EBADMSG which is presumably more
self-documenting and readable. Indeed, the '_READ' suffix does not tell much and
even confuses, while '_EBADMSG' tells about uncorrectable ECC error, because we
use -EBADMSG all over the place to represent ECC errors.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
One line was longer than 80 lines, make it shorter.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Cleanup the Kconfig for UBI by using menuconfig to enable/disable the entire
driver. Remove the dependency checks for MTD_UBI and MTD_UBI_DEBUG by
wrapping the options in if/endif blocks and remove any redundant checks.
Remove all default n since that is the Kconfig default. Change menu "Additional
UBI debugging messages" into a comment to remove one menu level.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
|
|
When an erroneous PEB is scheduling for scrubbing, we end up with the
following oops:
[<c0162404>] (prot_queue_del+0x0/0x50) from [<c01635b4>] (ubi_wl_scrub_peb+0xec/0x13c)
[<c01634c8>] (ubi_wl_scrub_peb+0x0/0x13c) from [<c01603bc>] (ubi_eba_read_leb+0x200/0x428)
[<c01601bc>] (ubi_eba_read_leb+0x0/0x428) from [<c015e3c0>] (ubi_leb_read+0xe8/0x138)
[<c015e2d8>] (ubi_leb_read+0x0/0x138) from [<c00d6918>] (ubifs_start_scan+0x7c/0xf4)
[<c00d689c>] (ubifs_start_scan+0x0/0xf4) from [<c00e3650>] (ubifs_recover_leb+0x3c/0x730)
[<c00e3614>] (ubifs_recover_leb+0x0/0x730) from [<c00e444c>] (ubifs_recover_log_leb+0xc8/0x2dc)
[<c00e4384>] (ubifs_recover_log_leb+0x0/0x2dc) from [<c00d7c20>] (ubifs_replay_journal+0xb90/0x13a4)
[<c00d7090>] (ubifs_replay_journal+0x0/0x13a4) from [<c00cdd68>] (ubifs_fill_super+0xb84/0x1054)
[<c00cd1e4>] (ubifs_fill_super+0x0/0x1054) from [<c00ced04>] (ubifs_get_sb+0xc4/0x2ac)
[<c00cec40>] (ubifs_get_sb+0x0/0x2ac) from [<c007f04c>] (vfs_kern_mount+0x58/0x94)
[<c007eff4>] (vfs_kern_mount+0x0/0x94) from [<c007f0e8>] (do_kern_mount+0x40/0xe8)
[<c007f0a8>] (do_kern_mount+0x0/0xe8) from [<c0095628>] (do_new_mount+0x68/0x8c)
[<c00955c0>] (do_new_mount+0x0/0x8c) from [<c00957a8>] (do_mount+0x15c/0x1b8)
[<c009564c>] (do_mount+0x0/0x1b8) from [<c0095890>] (sys_mount+0x8c/0xd4)
[<c0095804>] (sys_mount+0x0/0xd4) from [<c0023c00>] (ret_fast_syscall+0x0/0x2c)
Kernel panic - not syncing: Fatal exception
The problem is that 'ubi_wl_scrub_peb()' does not expect that PEBs may
be in the erroneous tree, which is a bug. This patch fixes the bug
and adds corresponding check to 'ubi_wl_scrub_peb()'. Now it will simply
ignore erroneous PEBs, instead of causing an oops.
Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
warning: (OPTPROBES && KPROBES && HAVE_OPTPROBES && !PREEMPT && DEBUG_KERNEL ||
MTD_UBI_DEBUG && MTD && SYSFS && MTD_UBI || UBIFS_FS_DEBUG && MISC_FILESYSTEMS &&
UBIFS_FS || LOCKDEP && DEBUG_KERNEL && TRACE_IRQFLAGS_SUPPORT &&
STACKTRACE_SUPPORT && LOCKDEP_SUPPORT || LATENCYTOP && HAVE_LATENCYTOP_SUPPORT &&
DEBUG_KERNEL && STACKTRACE_SUPPORT && PROC_FS) selects KALLSYMS_ALL
which has unmet direct dependencies (DEBUG_KERNEL && KALLSYMS)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Commit 0798cea8c2e1afee59686c51d27d0e96b05e42d1 "UBI: improve corrupted flash handling"
broke delet-compatible volumes handling - it introduced a limit of 8 eraseblocks which
may be corrupted. And delete-compatible eraseblocks are added to the "corrupted" list,
so if we'd have a large delete-compatible volume, UBI would refuse it.
The fix is to add delete-compatible volumes to the erase list instead. Indeed, they are
corrupted, we just have to erase them.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
list_for_each_entry uses its first argument to move from one element to the
next, so modifying it can break the iteration. The variable re1 is already
used within the loop as a temporary variable, and is not live here.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
iterator name list_for_each_entry;
expression x,E;
position p1,p2;
@@
list_for_each_entry@p1(x,...) { <... x =@p2 E ...> }
@@
expression x,E;
position r.p1,r.p2;
statement S;
@@
*x =@p2 E
...
list_for_each_entry@p1(x,...) S
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Currently, when UBI attaches an MTD device and cannot reserve all 1% (by
default) of PEBs for bad eraseblocks handling, it prints a warning. However,
Matthew L. Creech <mlcreech@gmail.com> is not very happy to see this warning,
because he did reserve enough of PEB at the beginning, but with time some
PEBs became bad. The warning is not necessary in this case.
This patch makes UBI print the warning
o if this is a new image
o of this is used image and the amount of reserved PEBs is only 10% (or less)
of the size of the reserved PEB pool.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Currently UBI prints
UBI: corrupted PEBs will be formatted
even if there are not corrupted PEBs. Fix this.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
When a delete-compatible volume is found, it is first added to the
'corr' list, which contains "corrupted" PEBs which should be erased,
and then it is added to the used volumes tree. However, the second
step should not be done. This does not cause problems in practice,
because we never access delete-compattible volumes, but it is still
not the right thing to do.
[Artem: amended the commit message and few prints]
Signed-off-by: Brijesh Singh <brijesh.s.singh@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Fix the followong compilation warnings introduced by commit
095751a6e0838a712393a74eb0b7b6559dbdbe81:
drivers/mtd/ubi/scan.c: In function 'check_what_we_have':
drivers/mtd/ubi/scan.c:960: warning: passing argument 1 of 'get_random_bytes' discards qualifiers from pointer target type
Fix the following compilation warnings introduced by commit
1a49af2ca019dcb4614c32f832bbcb814b61409c:
drivers/mtd/ubi/io.c: In function 'ubi_io_read':
drivers/mtd/ubi/io.c:153: warning: initialization makes integer from pointer without a cast
drivers/mtd/ubi/io.c:170: warning: format '%s' expects type 'char *', but argument 5 has type 'int'
drivers/mtd/ubi/io.c:177: warning: format '%zd' expects type 'signed size_t', but argument 7 has type 'int'
drivers/mtd/ubi/io.c:177: warning: too many arguments for format
Also, amend the ECC error code string and add brackets and whitespace
there - this should make the message readable.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Generate random image_seq when attaching empty MTD device (kernel do the
ubi formating).
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
ECC errors are quite typical errors on NAND, so it is worth improving
the UBI message and print something like
ubi_io_read: error -74 (ECC error) while reading 4096 bytes from PEB 1:4 ...
rather than
ubi_io_read: error -74 while reading 4096 bytes from PEB 1:4 ...
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
This patch improves the way UBI handles corrupted flash, or flash
containing garbage or non-UBI data, which is the same from UBI POW.
Namely, we do the following:
* if 5% or more PEBs are corrupted, refuse the flash
* if less than 5% PEBs are corrupted, do not refuse the flash
and format these PEBs
* if less than 8 PEBs are corrupted, format them silently, otherwise
print a warning message.
Reported-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Reviewed-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Tested-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
|
|
This is just a preparation patch which introduces several
'struct ubi_scan_info' fields which count eraseblocks of different
types. This will be used later on to decide whether it is safe to
format the flash or not. No functional changes so far.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Reviewed-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Tested-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
|
|
This patch introduces the %UBI_IO_BAD_HDR_READ return code for
the I/O level function. We will use this code in order to distinguish
between "corrupted header possibly because this is non-ubi data" and
"corrupted header possibly because of real data corruption and ECC error".
So far this patch does not introduce any functional change, just a
preparation.
This patch is pased on a patch from
Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Reviewed-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Tested-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
|
|
We do not really need 2 separate error codes for indicating bad VID
and bad EC headers (UBI_IO_BAD_EC_HDR, UBI_IO_BAD_VID_HDR), it is
enough to have only one UBI_IO_BAD_HDR return code.
This patch does not introduce any functional change, only some
code simplification.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Reviewed-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Tested-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
UBI can be built into the kernel or be compiled as a kernel module.
Further on the command line one can specify MTD devices to be attach to
UBI while loading. In the current implementation the UBI driver refuses
to load if one of the MTD devices cannot be attached.
Consider:
1) UBI compiled into the kernel and
2) a MTD device specified on the command line and
3) this MTD device contains bogus data (for whatever reason).
During init UBI tries to attach the MTD device is this fails the whole
UBI subsystem isn't initialized. Later the userspace cannot attach any
MTD to UBI because UBI isn't loaded.
This patch keeps the current behaviour: if UBI is compiled as a module
and a MTD device cannot be attached the UBI module cannot be loaded,
but changes it for the UBI-is-built-into-the-kernel usecase.
If UBI is builtin, a not attachable MTD device doen't stop UBI from
initializing. This slightly modifies the behaviour if multiple MTD
devices are specified on the command line. Now every MTD device is
probed and, if possible, attached, i.e. a faulty MTD device doesn't
stop the others from being attached.
Artem: tweaked the patch
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
The UBI reboot notifier causes problems with hibernation. Move this
functionality into the low-level MTD driver instead.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
Passing the attribute to the low level IO functions allows all kinds
of cleanups, by sharing low level IO code without requiring
an own function for every piece of data.
Also drivers can extend the attributes with own data fields
and use that in the low level function.
This makes the class attributes the same as sysdev_class attributes
and plain attributes.
This will allow further cleanups in drivers.
Full tree sweep converting all users.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Add an extra debugging check function which validates writes.
After every write it reads the data back, compares it with the
original data, and complains if they mismatch.
Useful for debugging. No-op if extra debugging checks are disabled.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
UBI debugging functions were a little bit over-engineered and
returned more error codes than needed, and the callers had to
do useless checks. Simplify the return codes.
Impact: only debugging code is affected, which means that for
non-developers this is a no-op patch.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
In the error path of 'ubi_attach_mtd_dev()' we have a tricky situation:
we have to release things differently depending on at which point
the failure happening. Namely, if @ubi->dev is not initialized, we have
to free everything ourselves. But if it was, we should not free the @ubi
object, because it will be freed in the 'dev_release()' function. And
we did not get this situation right.
This patch introduces additional argument to the 'uif_init()' function.
On exit, this argument indicates whether the final 'free(ubi)' will
happen in 'dev_release()' or not. So the caller always knows how to
properly release the resources.
Impact: all memory is now correctly released when UBI fails to attach
an MTD device.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
This patch adds a capability to attach MTD devices by their character
device paths. For example, one can do:
$ modprobe ubi mtd=/dev/mtd0
to attach /dev/mtd0.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
The @mtd_devs and @mtd_dev_param variables are used only during the
initialization, and all functions that use the variables have
the __init prefix. This means we can safely mark the variables
as __initdata, which is a tiny optimization.
Impact: tiny RAM consumption optimization when UBI is used as a kernel
module.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
Artem Bityutskiy
Linus Torvalds
Anatolij Gustschin
Joe Perches
Dan Carpenter
H Hartley Sweeten
Arnd Bergmann
Randy Dunlap
Julia Lawall
Brijesh Singh
Matthieu CASTET
Christoph Hellwig
Shinya Kuribayashi
Marc Kleine-Budde
Kevin Cernekee
Tejun Heo
Andi Kleen