aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/can/sja1000 (follow)
AgeCommit message (Collapse)AuthorFilesLines
2010-03-21can: sja1000: add read/write routines for 8, 16 and 32-bit register accessYegor Yefremov1-4/+38
add routines for 8, 16 and 32-bit access like in drivers/i2c/busses/i2c-pca-platform.c Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Acked-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-21can: sja1000: allow shared interrupt definitionYegor Yefremov1-1/+1
extend the AND mask, so that IRQF_SHARED flag remains Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-26can: netlink support for bus-error reporting and countersWolfgang Grandegger1-3/+22
This patch makes the bus-error reporting configurable and allows to retrieve the CAN TX and RX bus error counters via netlink interface. I have added support for the SJA1000. The TX and RX bus error counters are also copied to the data fields 6..7 of error messages when state changes are reported. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-03can: add support for CAN interface cards based on the PLX90xx PCI bridgePavel Cheblakov3-0/+485
This driver is for CAN interface cards based on the PLX90xx PCI bridge. Driver supports now: - Adlink PCI-7841/cPCI-7841 card (http://www.adlinktech.com/) - Adlink PCI-7841/cPCI-7841 SE card - Marathon CAN-bus-PCI card (http://www.marathon.ru/) - TEWS TECHNOLOGIES TPMC810 card (http://www.tews.com/) Changes since v1: - Added some defines for static inline int plx_pci_check_sja1000(...) - static struct pci_device_id plx_pci_tbl[] replaced by static DEFINE_PCI_DEVICE_TABLE(plx_pci_tbl) - Typo fixed Signed-off-by: Pavel Cheblakov <P.B.Cheblakov@inp.nsk.su> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-15can: Proper ctrlmode handling for CAN devicesChristian Pellegrin1-0/+1
This patch adds error checking of ctrlmode values for CAN devices. As an example all availabe bits are implemented in the mcp251x driver. Signed-off-by: Christian Pellegrin <chripell@fsfe.org> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-12can: Unify droping of invalid tx skbs and netdev statsOliver Hartkopp1-0/+3
To prevent the CAN drivers to operate on invalid socketbuffers the skbs are now checked and silently dropped at the xmit-function consistently. Also the netdev stats are consistently using the CAN data length code (dlc) for [rx|tx]_bytes now. Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07drivers/net/: use DEFINE_PCI_DEVICE_TABLE()Alexey Dobriyan2-2/+2
Use DEFINE_PCI_DEVICE_TABLE() so we get place PCI ids table into correct section in every case. Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-13can: Fix data length code handling in rx pathOliver Hartkopp1-10/+8
A valid CAN dataframe can have a data length code (DLC) of 0 .. 8 data bytes. When reading the CAN controllers register the 4-bit value may contain values from 0 .. 15 which may exceed the reserved space in the socket buffer! The ISO 11898-1 Chapter 8.4.2.3 (DLC field) says that register values > 8 should be reduced to 8 without any error reporting or frame drop. This patch introduces a new helper macro to cast a given 4-bit data length code (dlc) to __u8 and ensure the DLC value to be max. 8 bytes. The different handlings in the rx path of the CAN netdevice drivers are fixed. Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-18drivers/net/can: remove exceptional & on function nameJulia Lawall1-1/+1
In this file, function names are otherwise used as pointers without &. A simplified version of the semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @r@ identifier f; @@ f(...) { ... } @@ identifier r.f; @@ - &f + f // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-17Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6David S. Miller1-0/+47
Conflicts: drivers/net/can/Kconfig
2009-11-13can: Fix driver Kconfig structureOliver Hartkopp1-0/+47
In 2.6.32-rc the new EMS USB CAN driver was contributed and added the Kconfig entry right behind an entry of the same *vendor*. This teared the SJA1000 based driver selection into pieces. This fix cleans up the 2.6.32-rc Kconfig files for the CAN drivers and moves the SJA1000 and USB Kconfig portions into the belonging directories. As there are many new CAN drivers in the queue getting this cleanup into 2.6.32-rc would massively reduce the problems for the upcoming drivers. Thanks, Oliver Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-27Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6David S. Miller1-0/+1
Conflicts: drivers/net/sh_eth.c
2009-10-27can: sja1000: fix bug using library functions for skb allocationKurt Van Dijck1-2/+0
Commit 7b6856a0 "can: provide library functions for skb allocation" did not properly remove two lines of the SJA1000 driver resulting in a 'skb_over_panic' when calling skb_put, as reported by Kurt. Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-20can: provide library functions for skb allocationWolfgang Grandegger1-10/+2
This patch makes the private functions alloc_can_skb() and alloc_can_err_skb() of the at91_can driver public and adapts all drivers to use these. While making the patch I realized, that the skb's are *not* setup consistently. It's now done as shown below: skb->protocol = htons(ETH_P_CAN); skb->pkt_type = PACKET_BROADCAST; skb->ip_summed = CHECKSUM_UNNECESSARY; *cf = (struct can_frame *)skb_put(skb, sizeof(struct can_frame)); memset(*cf, 0, sizeof(struct can_frame)); The frame is zeroed out to avoid uninitialized data to be passed to user space. Some drivers or library code did not set "pkt_type" or "ip_summed". Also, "__constant_htons()" should not be used for runtime invocations, as pointed out by David Miller. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-14net: Fix OF platform drivers coldplug/hotplug when compiled as modulesAnton Vorontsov1-0/+1
Some OF platform drivers are missing module device tables, so they won't load automatically on boot. This patch fixes the issue by adding proper MODULE_DEVICE_TABLE() macros to the drivers. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-13can: make the number of echo skb's configurableWolfgang Grandegger2-1/+4
This patch allows the CAN controller driver to define the number of echo skb's used for the local loopback (echo), as suggested by Kurt Van Dijck, with the function: struct net_device *alloc_candev(int sizeof_priv, unsigned int echo_skb_max); The CAN drivers have been adapted accordingly. For the ems_usb driver, as suggested by Sebastian Haas, the number of echo skb's has been increased to 10, which improves the transmission performance a lot. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-24ems_pci: fix size of CAN controllers BAR mapping for CPC-PCI v2Sebastian Haas1-7/+9
The driver mapped only 128 bytes of the CAN controller address space when a CPC-PCI v2 was detected (incl. CPC-104P). This patch will fix it by always mapping the whole address space (4096 bytes on all boards) of the corresponding PCI BAR. Signed-off-by: Sebastian Haas <haas@ems-wuensche.com> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-04can: sja1000: legacy SJA1000 ISA bus driverWolfgang Grandegger2-0/+282
This patch adds support for legacy SJA1000 CAN controllers on the ISA or PC-104 bus. The I/O port or memory address and the IRQ number must be specified via module parameters: insmod sja1000_isa.ko port=0x310,0x380 irq=7,11 for ISA devices using I/O ports or: insmod sja1000_isa.ko mem=0xd1000,0xd1000 irq=7,11 for memory mapped ISA devices. Indirect access via address and data port is supported as well: insmod sja1000_isa.ko port=0x310,0x380 indirect=1 irq=7,11 Here is a full list of the supported module parameters: port:I/O port number (array of ulong) mem:I/O memory address (array of ulong) indirect:Indirect access via address and data port (array of byte) irq:IRQ number (array of int) clk:External oscillator clock frequency (default=16000000 [16 MHz]) (array of int) cdr:Clock divider register (default=0x48 [CDR_CBP | CDR_CLK_OFF]) (array of byte) ocr:Output clock register (default=0x18 [OCR_TX0_PUSHPULL]) (array of byte) Note: for clk, cdr, ocr, the first argument re-defines the default for all other devices, e.g.: insmod sja1000_isa.ko mem=0xd1000,0xd1000 irq=7,11 clk=24000000 is equivalent to insmod sja1000_isa.ko mem=0xd1000,0xd1000 irq=7,11 \ clk=24000000,24000000 Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Tested-by: Oliver Hartkopp <oliver@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-04can: sja1000: fix network statistics updateWolfgang Grandegger1-3/+2
The member "tx_bytes" of "struct net_device_stats" should be incremented when the interrupt is done and an "arbitration lost error" is a TX error and the statistics should be updated accordingly. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02drivers: Kill now superfluous ->last_rx storesEric Dumazet1-2/+0
The generic packet receive code takes care of setting netdev->last_rx when necessary, for the sake of the bonding ARP monitor. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Neil Horman <nhorman@txudriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01netdev: convert bulk of drivers to netdev_tx_tStephen Hemminger1-1/+2
In a couple of cases collapse some extra code like: int retval = NETDEV_TX_OK; ... return retval; into return NETDEV_TX_OK; Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-23Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6David S. Miller1-1/+0
Conflicts: drivers/net/wireless/iwmc3200wifi/netdev.c net/wireless/scan.c
2009-07-23can: sja1000: Add support for the new 4 channel EMS CPC-PCI cardsSebastian Haas1-44/+108
This patch adds support to the ems_pci driver for the new, v2, 4 channel CPC-PCI/PCIe/104P CAN cards from EMS Dr. Thomas Wuensche. Signed-off-by: Sebastian Haas <haas@ems-wuensche.com> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-20can: sja1000: remove duplicated includesWolfgang Grandegger1-1/+0
Remove duplicated #include('s) in drivers/net/can/sja1000/sja1000.c Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-05net: use NETDEV_TX_OK instead of 0 in ndo_start_xmit() functionsPatrick McHardy1-1/+1
This patch is the result of an automatic spatch transformation to convert all ndo_start_xmit() return values of 0 to NETDEV_TX_OK. Some occurences are missed by the automatic conversion, those will be handled in a seperate patch. Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-10can: sja1000_of_platform: fix build problems with printk formatWolfgang Grandegger1-4/+6
According to "Documentation/printk-formats.txt", if the type is dependent on a config option for its size, like resource_size_t, we should use a format specifier of its largest possible type and explicitly cast to it. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-01can: sja1000: generic OF platform bus driverWolfgang Grandegger2-0/+234
This patch adds a generic driver for SJA1000 chips on the OpenFirmware platform bus found on embedded PowerPC systems. You need a SJA1000 node definition in your flattened device tree source (DTS) file similar to: can@3,100 { compatible = "nxp,sja1000"; reg = <3 0x100 0x80>; interrupts = <2 0>; interrupt-parent = <&mpic>; nxp,external-clock-frequency = <16000000>; }; See also Documentation/powerpc/dts-bindings/can/sja1000.txt. CC: devicetree-discuss@ozlabs.org Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-01can: sja1000: stop misusing member base_addr of struct net_deviceWolfgang Grandegger5-98/+95
As discussed on the netdev mailing list, the member "base_addr" of "struct net_device" should not be (mis)used to store the virtual address to the SJA1000 register area. According to David Miller, it's only use is to allow ISA and similar primitive bus devices to have their I/O ports changed via ifconfig. The virtual address is now stored in the private data structure of the SJA1000 device and the callback functions use "struct sja1000_priv" instead of the unneeded "struct net_device". Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-01can: some fixes and cleanups to the initial device driver interfaceWolfgang Grandegger2-4/+1
This patch fixes a few errors sneaked into the initial version of the device driver interface. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-18The patch adds support for the PCI cards: PCIcan and PCIcanx (1, 2 or 4 channel) from Kvaser (http://www.kvaser.com).Wolfgang Grandegger2-0/+412
Signed-off-by: Per Dalen <per.dalen@cnw.se> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-18can: SJA1000 driver for EMS PCI cardsWolfgang Grandegger2-0/+330
The patch adds support for the one or two channel CPC-PCI and CPC-PCIe cards from EMS Dr. Thomas Wuensche (http://www.ems-wuensche.de). Signed-off-by: Sebastian Haas <haas@ems-wuensche.com> Signed-off-by: Markus Plessing <plessing@ems-wuensche.com> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-18can: SJA1000 generic platform bus driverWolfgang Grandegger2-0/+165
This driver adds support for the SJA1000 chips connected to the "platform bus", which can be found on various embedded systems. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-18can: Driver for the SJA1000 CAN controllerWolfgang Grandegger3-0/+824
This patch adds the generic Socket-CAN driver for the Philips SJA1000 full CAN controller. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Oliver Hartkopp <oliver.hartkopp@volkswagen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.