| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In commit a6d190f8c767 ("can: skb: drop tx skb if in listen only
mode") the priv->ctrlmode element is read even on virtual CAN
interfaces that do not create the struct can_priv at startup. This
out-of-bounds read may lead to CAN frame drops for virtual CAN
interfaces like vcan and vxcan.
This patch mainly reverts the original commit and adds a new helper
for CAN interface drivers that provide the required information in
struct can_priv.
Fixes: a6d190f8c767 ("can: skb: drop tx skb if in listen only mode")
Reported-by: Dariusz Stojaczyk <Dariusz.Stojaczyk@opensynergy.com>
Cc: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Cc: Max Staudt <max@enpas.org>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20221102095431.36831-1-socketcan@hartkopp.net
Cc: stable@vger.kernel.org # 6.0.x
[mkl: patch pch_can, too]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
|
|
Currently, some CAN drivers support hardware timestamping, some do
not. But userland has no method to query which features are supported
(aside maybe of getting RX messages and observe whether or not
hardware timestamps stay at zero).
The canonical way for a network driver to advertised what kind of
timestamping it supports is to implement ethtool_ops::get_ts_info().
This patch only targets the CAN drivers which *do not* support
hardware timestamping. For each of those CAN drivers, implement the
get_ts_info() using the generic ethtool_op_get_ts_info().
This way, userland can do:
| $ ethtool --show-time-stamping canX
to confirm the device timestamping capacities.
N.B. the drivers which support hardware timestamping will be migrated
in separate patches.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20220727101641.198847-6-mailhol.vincent@wanadoo.fr
[mkl: mscan: add missing mscan_ethtool_ops]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add a dedicated flag in uapi/linux/can/error.h to notify the userland
that fields data[6] and data[7] of the CAN error frame were
respectively populated with the tx and rx error counters.
For all driver tree-wide, set up this flags whenever needed.
Link: https://lore.kernel.org/all/20220719143550.3681-12-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license as published by the
free software foundation version 2 this program is distributed as is
without any warranty of any kind whether express or implied without
even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit 30f3b42147ba6f ("can: mark led trigger as broken") the
CAN specific LED support was disabled and marked as BROKEN. As the
common LED support with CONFIG_LEDS_TRIGGER_NETDEV should do this work
now the code can be removed as preparation for a CAN netdevice Kconfig
rework.
Link: https://lore.kernel.org/all/20220518154527.29046-1-socketcan@hartkopp.net
Suggested-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
[mkl: remove led.h from MAINTAINERS]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch renames the function can_rx_offload_queue_sorted() to
can_rx_offload_queue_timestamp(). This better describes what the
function does, it adds a newly RX'ed skb to the sorted queue by its
timestamp.
Link: https://lore.kernel.org/all/20220417194327.2699059-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue when
using hierarchical interrupt domains using "interrupts" property in
the node as this bypasses the hierarchical setup and messes up the irq
chaining.
In preparation for removal of static setup of IRQ resource from DT
core code use platform_get_irq().
Link: https://lore.kernel.org/all/20211221194508.11737-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Adding a skb to the skb_queue in rx-offload requires to take a lock.
This commit avoids this by adding an unlocked skb queue that is
appended at the end of the ISR. Having one lock at the end of the ISR
should be OK as the HW is empty, not about to overflow.
Link: https://lore.kernel.org/r/20210724204745.736053-2-mkl@pengutronix.de
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Co-developed-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In order to implement byte queue limits (bql) in CAN drivers, the length of the
CAN frame needs to be passed into the networking stack after queueing and after
transmission completion.
To avoid to calculate this length twice, extend can_rx_offload_get_echo_skb()
to return that value. Convert all users of this function, too.
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20210111141930.693847-15-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add a frame_len argument to can_put_echo_skb() which is used to save length of
the CAN frame into field frame_len of struct can_skb_priv so that it can be
later used after transmission completion. Convert all users of this function,
too.
Drivers which implement BQL call can_put_echo_skb() with the output of
can_skb_get_frame_len(skb) and drivers which do not simply pass zero as an
input (in the same way that NULL would be given to can_get_echo_skb()). This
way, we have a nice symmetry between the two echo functions.
Link: https://lore.kernel.org/r/20210111061335.39983-1-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20210111141930.693847-13-mkl@pengutronix.de
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
|
|
The naming of can_dlc as element of struct can_frame and also as variable
name is misleading as it claims to be a 'data length CODE' but in reality
it always was a plain data length.
With the indroduction of a new 'len' element in struct can_frame we can now
remove can_dlc as name and make clear which of the former uses was a plain
length (-> 'len') or a data length code (-> 'dlc') value.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201120100444.3199-1-socketcan@hartkopp.net
[mkl: gs_usb: keep struct gs_host_frame::can_dlc as is]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The get_can_dlc() macro is used to ensure the payload length information of
the Classical CAN frame to be max 8 bytes (the CAN_MAX_DLEN).
Rename the macro and use the correct constant in preparation of the len/dlc
cleanup for Classical CAN frames.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201110101852.1973-3-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In the error handling, we should goto the probe_exit_candev
to free ndev to prevent memory leak.
Fixes: dabf54dd1c63 ("can: ti_hecc: Convert TI HECC driver to DT only driver")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201114111708.3465543-1-zhangqilong3@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The driver forgets to call clk_disable_unprepare() in error path after
a success calling for clk_prepare_enable().
Fix it by adding a clk_disable_unprepare() in error path.
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1594973079-27743-1-git-send-email-zhangchangzhong@huawei.com
Fixes: befa60113ce7 ("can: ti_hecc: add missing prepare and unprepare of the clock")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Use the function devm_platform_ioremap_resource_byname() to simplify
source code which calls the functions platform_get_resource_byname()
and devm_ioremap_resource(). Remove also a few error messages which
became unnecessary with this software refactoring.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Link: https://lore.kernel.org/r/20200420132207.8536-1-zhengdejin5@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch fixes spelling erros found by "codespell" in the
drivers/net/can subtree.
Link: https://lore.kernel.org/r/20200915223527.1417033-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The skbs for classic CAN and CAN FD frames are allocated with seperate
functions: alloc_can_skb() and alloc_canfd_skb().
In order to support CAN FD frames via the rx-offload helper, the driver
itself has to allocate the skb (depending whether it received a classic
CAN or CAN FD frame), as the rx-offload helper cannot know which kind of
CAN frame the driver has received.
This patch moves the allocation of the skb into the struct
can_rx_offload::mailbox_read callbacks of the the flexcan and ti_hecc
driver and adjusts the rx-offload helper accordingly.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
While the ti_hecc has interrupts to report when the error counters increase
to a certain level and which change state it doesn't handle the case that
the error counters go down again, so the reported state can actually be
wrong. Since there is no interrupt for that, do update state based on the
error counters, when the state is not error active and goes down again.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The HECC_CANES register handles the flags specially, it only updates
the flags after a one is written to them. Since the interrupt for
frame errors is not enabled an old error can hence been seen when a
state interrupt arrives. For example if the device is not connected
to the CAN-bus the error warning interrupt will have HECC_CANES
indicating there is no ack. The error passive interrupt thereafter
will have HECC_CANES flagging that there is a warning level. And if
thereafter there is a message successfully send HECC_CANES points to
an error passive event, while in reality it became error warning
again. In summary, the state is not always reported correctly.
So handle the state changes and frame errors separately. The state
changes are now based on the interrupt flags and handled directly
when they occur. The reporting of the frame errors is still done as
before, as a side effect of another interrupt.
note: the hecc_clear_bit will do a read, modify, write. So it will
not only clear the bit, but also reset all other bits being set as
a side affect, hence it is replaced with only clearing the flags.
note: The HECC_CANMC_CCR is no longer cleared in the state change
interrupt, it is completely unrelated.
And use net_ratelimit to make checkpatch happy.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When the rx FIFO overflows the ti_hecc would silently drop them since
the overwrite protection is enabled for all mailboxes. So disable it for
the lowest priority mailbox and return a proper error value when receive
message lost is set. Drop the message itself in that case, since it
might be partially updated.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Acked-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Release the mailbox after reading it, so it can be reused a bit earlier.
Since "can: rx-offload: continue on error" all pending message bits are
cleared directly, so remove clearing them in ti_hecc.
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The HECC_CANMIM is set in the xmit path and cleared in the interrupt.
Since this is done with a read, modify, write action the register might
end up with some more MIM enabled then intended, since it is not
protected. That doesn't matter at all, since the tx interrupt disables
the mailbox with HECC_CANME (while holding a spinlock). So lets just
always keep MIM set.
While at it, since the mailbox direction never changes, don't set it
every time a message is send, ti_hecc_reset() already sets them to tx.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When the interface goes down, the CPK should no longer take an active
part in the CAN-bus communication, like sending acks and error frames.
So enable configuration mode in ti_hecc_stop, so the CPK is no longer
active.
When a transceiver switch is present the acks and errors don't make it
to the bus, but disabling the CPK then does prevent oddities, like
ti_hecc_reset() failing, since the CPK can become bus-off and starts
counting the 11 bit recessive bits, which seems to block the reset. It
can also cause invalid interrupts and disrupt the CAN-bus, since
transmission can be stopped in the middle of a message, by disabling the
tranceiver while the CPK is sending.
Since the CPK is disabled after normal power on, it is typically only
seen when the interface is restarted.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The call to can_rx_offload_queue_sorted() may fail and return an error
(in the current implementation due to resource shortage). The passed skb
is consumed.
This patch adds incrementing of the appropriate error counters to let
the device statistics reflect that there's a problem.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/can/ti_hecc.c: In function 'ti_hecc_mailbox_read':
drivers/net/can/ti_hecc.c:533:12: warning:
variable 'mbx_mask' set but not used [-Wunused-but-set-variable]
It is never used so can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds two blank lines in ti_hecc_mailbox_read() to improve the
readability of the function.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch changes the multiple assignments of HECC_TX_MASK in
ti_hecc_start() into two single ones.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch fixes the print format strings in the driver.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch fixes long lines in the driver.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch fixes the indention in the driver.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch converts all block comments to network subsystem style block
comments.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
As already mentioned in [1] and included in [2], there is an off by one
issue since the high bank is already enabled when the _next_ mailbox to
be read has index 12, so the mailbox being read was 13. The message can
therefore go into mailbox 31 and the driver will be repolled until the
mailbox 12 eventually receives a msg. Or the message might end up in the
12th mailbox, but then it would become disabled after reading it and only
be enabled again in the next "round" after mailbox 13 was read, which can
cause out of order messages, since the lower priority mailboxes can
accept messages in the meantime.
As mentioned in [3] there is a hardware race condition when changing the
CANME register while messages are being received. Even when including a
busy poll on reception, like in [2] there are still overflows and out of
order messages at times, but less then without the busy loop polling.
Unlike what the patch suggests, the polling time is not in the microsecond
range, but takes as long as a current CAN bus reception needs to finish,
so typically more in the fraction of millisecond range. Since the timeout
is in jiffies it won't timeout.
Even with these additional fixes the driver is still not able to provide a
proper FIFO which doesn't drop packages. So change the driver to use
rx-offload and base order on timestamp instead of message box numbers. As
a side affect, this also fixes [4] and [5].
Before this change messages with a single byte counter were dropped /
received out of order at a bitrate of 250kbit/s on an am3517. With this
patch that no longer occurs up to and including 1Mbit/s.
[1] https://linux-can.vger.kernel.narkive.com/zgO9inVi/patch-can-ti-hecc-fix-rx-wrong-sequence-issue#post6
[2] http://arago-project.org/git/projects/?p=linux-omap3.git;a=commit;h=02346892777f07245de4d5af692513ebd852dcb2
[3] https://linux-can.vger.kernel.narkive.com/zgO9inVi/patch-can-ti-hecc-fix-rx-wrong-sequence-issue#post5
[4] https://patchwork.ozlabs.org/patch/895956/
[5] https://www.spinics.net/lists/netdev/msg494971.html
Cc: Anant Gole <anantgole@ti.com>
Cc: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
After commit d75b1ade567f ("net: less interrupt masking in NAPI") napi
repoll is done only when work_done == budget.
So we need to return budget if there are still packets to receive.
Signed-off-by: Oliver Stäbler <oliver.staebler@bytesatwork.ch>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: dabf54dd1c63 ("can: ti_hecc: Convert TI HECC driver to DT only driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch converts TI HECC driver to DT only driver. This results in
removing ti_hecc.h containing now obsolete platform data.
Former transceiver_switch callback function will be now modelled via
regulator API.
Signed-off-by: Anton Glukhov <anton.a.glukhov@gmail.com>
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In order to make the driver work with the common clock framework, this
patch converts the clk_enable()/clk_disable() to
clk_prepare_enable()/clk_disable_unprepare().
Also add error checking for clk_prepare_enable().
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The assignment 'cf->data[2] |= CAN_ERR_PROT_UNSPEC' used at CAN error message
creation time is obsolete as CAN_ERR_PROT_UNSPEC is zero and cf->data[2] is
initialized with zero in alloc_can_err_skb() anyway.
So we could either assign 'cf->data[2] = CAN_ERR_PROT_UNSPEC' correctly or we
can remove the obsolete OR operation entirely.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
As Dan Carpenter reported in http://marc.info/?l=linux-can&m=144793696016187
the assignment of the error location in CAN error messages had some bit wise
overlaps. Indeed the value to be assigned in data[3] is no bitfield but defines
a single value which points to a location inside the CAN frame on the wire.
This patch fixes the assignments for the error locations in error messages.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.
Cc: Anant Gole <anantgole@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In order to be able to move the stats increment from can_bus_off() into
can_change_state(), the increment had to be moved back into code that was using
can_bus_off() but not can_change_state().
As a side-effect, this patch fixes the following bugs:
* Redundant call to can_bus_off() in c_can.
* Bus-off counted twice in xilinx_can.
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
CAN interfaces only support MTU values of 16 (CAN 2.0) and 72 (CAN FD).
Setting the MTU to other values is pointless but it does not really hurt.
With the introduction of the CAN FD support in drivers/net/can a new
function to switch the MTU for CAN FD has been introduced.
This patch makes use of this can_change_mtu() function to check for correct
MTU settings also in legacy CAN (2.0) devices.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the following sparse warning, which occurs in casts when
accessing the data in the CAN frames (struct can_frame) in the RX and TX
routines:
drivers/net/can/ti_hecc.c:521:17: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:521:17: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:521:17: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:521:17: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:521:17: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:521:17: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:524:25: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:524:25: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:524:25: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:524:25: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:524:25: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:524:25: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:572:28: warning: incorrect type in assignment (different base types)
drivers/net/can/ti_hecc.c:572:28: expected unsigned int [unsigned] [usertype] <noident>
drivers/net/can/ti_hecc.c:572:28: got restricted __be32 [usertype] <noident>
drivers/net/can/ti_hecc.c:575:40: warning: incorrect type in assignment (different base types)
drivers/net/can/ti_hecc.c:575:40: expected unsigned int [unsigned] [usertype] <noident>
drivers/net/can/ti_hecc.c:575:40: got restricted __be32 [usertype] <noident>
As the data is indeed big endian, use "__be32" instead of "u32", when casting
it.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch removes the priv->can.do_get_state() callback, as it just returns
priv->can.state. The callback's only user can_fill_info() has direct access to
priv->can.state.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Bring in the 'net' tree so that we can get some ipv4/ipv6 bug
fixes that some net-next work will build upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Errors in CAN protocol (location) are reported in data[3] of the can
frame instead of data[2].
Cc: linux-stable <stable@vger.kernel.org>
Cc: Anant Gole <anantgole@ti.com>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
Oliver Hartkopp
Linus Torvalds
Vincent Mailhol
Thomas Gleixner
Marc Kleine-Budde
Lad Prabhakar
Zhang Qilong
Zhang Changzhong
Dejin Zheng
Joakim Zhang
Jeroen Hofstee
YueHaibing
Oliver Stäbler
Wei Yongjun
Yegor Yefremov
Andri Yngvason
Wolfram Sang
Paul Gortmaker
Jingoo Han
David S. Miller
Olivier Sobrie