Age | Commit message (Collapse) | Author | Files | Lines |
|
According to section 12.0.3.4.13 "Receive Descriptor Control - RXDCTL"
of the IntelĀ® 82579 Gigabit Ethernet PHY Datasheet v2.1:
"HTHRESH should be given a non zero value when ever PTHRESH is
used."
In RXDCTL(0), PTHRESH lives at bits 5:0, and HTHREST lives at bits 13:8.
Set only bit 8 of HTHREST as is done in e1000_flush_rx_ring(). Found by
inspection.
Signed-off-by: Matt Turner <matt.turner@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds a new function igb_get_max_rss_queues() to get maximum
RSS queues, this will reduce duplicate code and facilitate future
maintenance.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Before libvirt modifies the MAC address and vlan tag for an SRIOV VF
for use by a virtual machine (either using vfio device assignment or
macvtap passthru mode), it saves the current MAC address and vlan tag
so that it can reset them to their original value when the guest is
done. Libvirt can't leave the VF MAC set to the value used by the
now-defunct guest since it may be started again later using a
different VF, but it certainly shouldn't just pick any random value,
either. So it saves the state of everything prior to using the VF, and
resets it to that.
The igb driver initializes the MAC addresses of all VFs to
00:00:00:00:00:00, and reports that when asked (via an RTM_GETLINK
netlink message, also visible in the list of VFs in the output of "ip
link show"). But when libvirt attempts to restore the MAC address back
to 00:00:00:00:00:00 (using an RTM_SETLINK netlink message) the kernel
responds with "Invalid argument".
Forbidding a reset back to the original value leaves the VF MAC at the
value set for the now-defunct virtual machine. Especially on a system
with NetworkManager enabled, this has very bad consequences, since
NetworkManager forces all interfacess to be IFF_UP all the time - if
the same virtual machine is restarted using a different VF (or even on
a different host), there will be multiple interfaces watching for
traffic with the same MAC address.
To allow libvirt to revert to the original state, we need a way to
remove the administrative set MAC on a VF, to allow normal host
operation again, and to reset/overwrite the VF MAC via VF netdev.
This patch implements the outlined scenario by allowing to set the
VF MAC to 00:00:00:00:00:00 via RTM_SETLINK on the PF.
igb_ndo_set_vf_mac resets the IGB_VF_FLAG_PF_SET_MAC flag to 0,
so it's possible to reset the VF MAC back to the original value via
the VF netdev.
Note: Recent patches to libvirt allow for a workaround if the NIC
isn't capable of resetting the administrative MAC back to all 0, but
in theory the NIC should allow resetting the MAC in the first place.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Tested-by: Aaron Brown <arron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Don't use error-prone-brute-force way.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add macro generated pkt_flag_names array, with a little help of which
the flags can be printed by using an index.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PKT_FALGS macro will be used to add package behavior names definitions
to simplify the code that prints/reads pkg flags.
Sorted the array in order of printing the flags in pktgen_if_show()
Note: Renamed IPSEC_ON => IPSEC for simplicity.
No visible behavior change expected.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o FLOW_SEQ now can be disabled with pgset "flag !FLOW_SEQ"
o FLOW_SEQ and FLOW_RND are antonyms, as it's shown by pktgen_if_show()
o IPSEC now may be disabled
Note, that IPV6 is enabled with dst6/src6 parameters, not with
a flag parameter.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Change process name in ps output: looks like, these days the process
is named kpktgend_<cpu>, rather than pktgen/<cpu>.
o Use pg_ctrl for start/stop as it can work well with pgset without
changes to $(PGDEV) variable.
o Clarify a bit needed $(PGDEV) definition for sample scripts and that
one needs to `source functions.sh`.
o Document how-to unset a behaviour flag, note about history expansion.
o Fix pgset spi parameter value.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
memset variables to 0 to fix sparse warnings:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_cudbg.c:409:42: sparse: Using
plain integer as NULL pointer
drivers/net/ethernet/chelsio/cxgb4/cudbg_zlib.c:43:47: sparse: Using
plain integer as NULL pointer
Fixes: ad75b7d32f25 ("cxgb4: implement ethtool dump data operations")
Fixes: 91c1953de387 ("cxgb4: use zlib deflate to compress firmware dump")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes:
drivers/net/ethernet/chelsio/cxgb4/cudbg_zlib.c:39:5: error:
redefinition of 'cudbg_compress_buff'
int cudbg_compress_buff(struct cudbg_init *pdbg_init,
^~~~~~~~~~~~~~~~~~~
In file included from
drivers/net/ethernet/chelsio/cxgb4/cudbg_zlib.c:23:0:
drivers/net/ethernet/chelsio/cxgb4/cudbg_zlib.h:45:19: note: previous
definition of 'cudbg_compress_buff' was here
static inline int cudbg_compress_buff(struct cudbg_init *pdbg_init,
^~~~~~~~~~~~~~~~~~~
Fixes: 91c1953de387 ("cxgb4: use zlib deflate to compress firmware dump")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the peer sends a shutdown WRITE, this should not affect sending
in general, and waiting for send buffer space in particular.
Stop waiting of the local socket for send buffer space only, if peer
signals closing, but not if peer signals just shutdown WRITE.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a socket is closed or shutdown, smc waits for data being transmitted
in certain states. If the state changes during this wait, the close
switch depending on state should be reentered.
In addition, state change is avoided if sending of close or shutdown fails.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Work requests are needed for every ib_post_send(), among them the
ib_post_send() to signal closing. If an smc socket program is cancelled,
the smc connections should be cleaned up, and require sending of closing
signals to the peer. This may fail, if a wait for
a free work request is needed, but is cancelled immediately due to the
cancel interrupt. To guarantee notification of the peer, the wait for
a work request is changed to uninterruptible.
And the area to receive work request completion info with
ib_poll_cq() is cleared first.
And _tx_ variable names are used in the _tx_routines for the
demultiplexing common type in the header.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to wait for confirmation of pending tx requests
for a closing connection, since pending tx slots are dismissed
when finishing a connection.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cleanup to avoid duplicate code in smc_clcsock_accept().
No functional change.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cleanup to consistently exploit the local struct sock definitions.
No functional change.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
implement ndo_set_vf_vlan for mgmt netdevice to configure
the PCIe VF.
Original work by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel discovered recently I broke TC filter replace (and fixed
it in commit ad9294dbc227 ("bpf: fix cls_bpf on filter replace")).
Add a test to make sure it never happens again.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make netdevsim print a message to the BPF verifier log buffer when a
program is offloaded.
Then use this message in hardware offload selftests to make sure that
using this buffer actually prints the message to the console for
eBPF hardware offload.
The message is appended after the last instruction is processed with the
verifying function from netdevsim. Output looks like the following:
$ tc filter add dev foo ingress bpf obj sample_ret0.o \
sec .text verbose skip_sw
Prog section '.text' loaded (5)!
- Type: 3
- Instructions: 2 (0 over limit)
- License:
Verifier analysis:
0: (b7) r0 = 0
1: (95) exit
[netdevsim] Hello from netdevsim!
processed 2 insns, stack depth 0
"verbose" flag is required to see it in the console since netdevsim does
not throw an error after printing the message.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should not compile netdevsim/bpf.c if BPF syscall is not
enabled. Otherwise bpf core would have to provide wrappers
for all functions offload drivers may call, even though
system will never see a BPF object.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add checks to test that netlink extack messages are correctly displayed
in some expected error cases for eBPF offload to netdevsim with TC and
XDP.
iproute2 may be built without libmnl support, in which case the extack
messages will not be reported. Try to detect this condition, and when
enountered print a mild warning to the user and skip the extack validation.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the recently added extack support for TC eBPF filters in netdevsim.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
use RCU instead of spin_{,unlock}_bh() to protect concurrent read/write on
act_csum configuration, to reduce the effects of contention in the data
path when multiple readers are present.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
use per-CPU counters, like other TC actions do, instead of maintaining one
set of stats across all cores. This allows updating act_csum stats without
the need of protecting them using spin_{,un}lock_bh() invocations.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It takes 1sec for bond link down notification to hit user-space
when all slaves of the bond go down. 1sec is too long for
protocol daemons in user-space relying on bond notification
to recover (eg: multichassis lag implementations in user-space).
Since the link event code already marks team device port link events
as urgent, this patch moves the code to cover all lag ports and master.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for the Marvell switch and names the network
ports according to the labels, that can be found next to the
connectors. The switch is connected to the host system using a
PCI based network card.
The PCI bus configuration has been written using the following
information:
root@b450v3# lspci -tv
-[0000:00]---00.0-[01]----00.0 Intel Corporation I210 Gigabit Network Connection
root@b450v3# lspci -nn
00:00.0 PCI bridge [0604]: Synopsys, Inc. Device [16c3:abcd] (rev 01)
01:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03)
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for the Marvell switch and names the network
ports according to the labels, that can be found next to the
connectors. The switch is connected to the host system using a
PCI based network card.
The PCI bus configuration has been written using the following
information:
root@b650v3# lspci -tv
-[0000:00]---00.0-[01]----00.0 Intel Corporation I210 Gigabit Network Connection
root@b650v3# lspci -nn
00:00.0 PCI bridge [0604]: Synopsys, Inc. Device [16c3:abcd] (rev 01)
01:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03)
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for the Marvell switch and names the network
ports according to the labels, that can be found next to the
connectors ("ID", "IX", "ePort 1", "ePort 2"). The switch is
connected to the host system using a PCI based network card.
The PCI bus configuration has been written using the following
information:
root@b850v3# lspci -tv
-[0000:00]---00.0-[01]----00.0-[02-05]--+-01.0-[03]----00.0 Intel Corporation I210 Gigabit Network Connection
+-02.0-[04]----00.0 Intel Corporation I210 Gigabit Network Connection
\-03.0-[05]--
root@b850v3# lspci -nn
00:00.0 PCI bridge [0604]: Synopsys, Inc. Device [16c3:abcd] (rev 01)
01:00.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port Gen2 Switch [10b5:8605] (rev ab)
02:01.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port Gen2 Switch [10b5:8605] (rev ab)
02:02.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port Gen2 Switch [10b5:8605] (rev ab)
02:03.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port Gen2 Switch [10b5:8605] (rev ab)
03:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03)
04:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03)
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
B850v3, B650v3 and B450v3 all have a GPIO bit banged MDIO bus to
communicate with a Marvell switch. On all devices the switch is
connected to a PCI based network card, which needs to be referenced
by DT, so this also adds the common PCI root node.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for enabling the internal PHY for a 'cpu' port.
It has been tested on GE B850v3, B650v3 and B450v3, which have a
built-in MV88E6240 switch hardwired to a PCIe based network card.
On these machines the internal PHY of the i210 network card and
the Marvell switch are connected to each other and must be enabled
for properly using the switch. While the i210 PHY will be enabled
when the network interface is enabled, the switch's port is not
exposed as network interface. Additionally the mv88e6xxx driver
resets the chip during probe, so the PHY is disabled without this
patch.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix recreating the channel VSIs during the reset flow to reconfigure
the Tx rings and the queue context associated with the channel VSI.
Also update the next_base_queue for the VSI while rebuilding the
channel VSIs after a reset.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If we receive the link status message from PF with link up before queues
are actually enabled, it will trigger a TX hang. This fixes the issue
by ignoring a link up message if the VF state is not yet in RUNNING
state.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Client close is overloaded to handle both un-registration and
netdev down event. On netdev down, i40iw client close is called
which unregisters the RDMA dev and this is too destructive
since the netdev is still registered.
Do not call client close/open on netdev down/up events. Instead
disable the PE TCP_ENA flag during a netdev down event. This
blocks all TCP traffic to the RDMA Protocol Engine. On netdev up,
re-enable the flag.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Now that i40e_vsi_config_tc() has the pf and hw variable defined, use
them, instead of dereferencing vsi->back. Much easier to read.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The driver (and the entire netdev layer for that matter) assumes
that TC0 will always be present in our DCB configuration.
Unfortunately, this isn't always the case. Rather than fail to
configure the VSI, let's go ahead and try to make it work, even
though DCB will end up being disabled by the kernel.
If the driver fails to configure DCB, the driver queries what's
valid, then writes that back to the hardware, always forcing TC0.
This fixes a bug where the driver could fail to adhere to ETS BW
allocations if 8 TCs were configured on the switch.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In VFs, there is a known issue which can cause writebacks
to not occur when interrupts are disabled and there are
less than 4 descriptors resulting in TX timeout. Timeout
can also occur due to lost interrupt.
The current implementation for detecting and recovering
from hung queues in the PF is problematic because it actually
actively encourages lost interrupts. By triggering a SW
interrupt, interrupts are forced on. If we are already in
napi_poll and an interrupt fires, napi_poll will not be
rescheduled and the interrupt is effectively lost; thereby
potentially *causing* hung queues.
This patch checks whether packets are being processed between
every watchdog cycle and determine potential hung queue and
fires triggers SW interrupt only for that particular queue.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This fix solves an issue occurring while calling i40e_led_set function
from the driver with "blink" parameter set as TRUE. This call resulted
in Activity LED blinking instead of Link LED, which may lead to errors
in physically identifying the port, since Activity LED may be blinking
for different reasons as well.
Signed-off-by: Michal Kuchta <michal.kuchta@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When a host disables and enables a PF device, all the associated
VFs are removed and added back in. It also generates a PFR which in turn
resets all the connected VFs. This behaviour is different from that of
Linux guest on Linux host. Hence we end up in a situation where there's
a PFR and device removal at the same time. And watchdog doesn't have a
clue about this and schedules a reset_task. This patch adds code to send
signal to reset_task that the device is currently being removed.
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
flush_schedule_work blocks until completion of all scheduled
work items in global work-queue. This can cause deadlock in some
cases. i40evf_remove() cleans up necessary work items with
cancel_delayed_work_sync and cancel_work_sync. This fix removes
flush_schedule_work call inside i40evf_remove().
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In some weird circumstances with DCB enabled, the firmware can fail to
configure the VSI, leaving us with zero traffic classes. Check for this
state when we configure RSS to avoid a panic.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds new I40E_NVMUPD_GET_AQ_EVENT state to allow
retrieval of AdminQ events as a result of AdminQ commands sent
to firmware.
Add preservation flags support on X722 devices for NVM update
AdminQ function wrapper. Add new parameter and handling to
nvmupdate admin queue function intended to allow nvmupdate tool
to configure the preservation flags in the AdminQ command.
This is required to implement FlatNVM on X722 devices.
Signed-off-by: Pawel Jablonski <pawel.jablonski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
With all the support code in place we can now link in the ipsec
offload operations and set the ESP feature flag for the XFRM
subsystem to see.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add a simple statistic to count the ipsec offloads.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If the skb has a security association referenced in the skb, then
set up the Tx descriptor with the ipsec offload bits. While we're
here, we fix an oddly named field in the context descriptor struct.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If the chip sees and decrypts an ipsec offload, set up the skb
sp pointer with the ralated SA info. Since the chip is rude
enough to keep to itself the table index it used for the
decryption, we have to do our own table lookup, using the
hash for speed.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
On a chip reset most of the table contents are lost, so must be
restored. This scans the driver's ipsec tables and restores both
the filled and empty table slots to their pre-reset values.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add the functions for setting up and removing offloaded SAs (Security
Associations) with the x540 hardware. We set up the callback structure
but we don't yet set the hardware feature bit to be sure the XFRM service
won't actually try to use us for an offload yet.
The software tables are made up to mimic the hardware tables to make it
easier to track what's in the hardware, and the SA table index is used
for the XFRM offload handle. However, there is a hashing field in the
Rx SA tracking that will be used to facilitate faster table searches in
the Rx fast path.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Set up the data structures to be used by the ipsec offload.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add in the code for running and stopping the hardware ipsec
encryption/decryption engine. It is good to keep the engine
off when not in use in order to save on the power draw.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|