aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/e1000e/phy.c (follow)
AgeCommit message (Collapse)AuthorFilesLines
2010-01-13e1000e: MDIO slow mode should always be done for 82577Bruce Allan1-85/+0
A previous 82577 workaround that set the MDIO access speed to slow mode for every PHY register read/write when the cable is unplugged should instead set the access mode to always be slow before any PHY register access. Since the mode bit gets cleared when the PHY is reset, set the mode after every PHY reset. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: correct ICH/PCH PHY operations function pointersBruce Allan1-14/+177
Some function pointers for a few PHY operations (for 82578 and 82567) and were set incorrectly causing functions to be executed that were accessing incorrect PHY register offsets for that particular device. This patch also moves a few PHY-specific functions from ich8lan.c to the more appropriate phy.c. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: refactor PHY ID detection workaroundBruce Allan1-10/+16
The workaround that detects the correct PHY ID when an initial read of the PHY ID registers returns an invalid one should retry up to ten times with a small delay between attempts using a single PHY address and then repeat using the remaining possible PHY addresses. Do this instead of trying each possible PHY address repeating that up to 100 times. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: PHY type cleanups in e1000e_check_downshift()Bruce Allan1-1/+1
Remove the case for 82577 because it does not support the ability to check for downshift. Add case for e1000_phy_bm which can do this. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: add debug messagesBruce Allan1-6/+20
Add some helpful debug messages. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: comment correctionsBruce Allan1-7/+7
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: provide family-specific PHY power up/down operationsBruce Allan1-0/+37
The different families (80003es2lan, 8257x, ICHx/PCH) supported by the driver each have their own conditions when the PHY can be powered down. This patch rewrites the PHY power up/down code to fit with the family- specific style used in the driver. All pre-existing calls to power up or down the PHY remain untouched. A new call to power down the PHY when removing the driver when the interface is down replaces the current call to reset the PHY in order to reduce power consumption. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02e1000e: guard against buffer overflow in cable length tablesBruce Allan1-3/+11
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-29Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6David S. Miller1-34/+22
Conflicts: drivers/ieee802154/fakehard.c drivers/net/e1000e/ich8lan.c drivers/net/e1000e/phy.c drivers/net/netxen/netxen_nic_init.c drivers/net/wireless/ath/ath9k/main.c
2009-11-21e1000e: set bools to true/false instead of 1/0Bruce Allan1-3/+3
Set booleans to 'true' or 'false' to make it clear it is a boolean. Also change instances of TRUE/FALSE in comments to lowercase true/false. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: update copyright informationBruce Allan1-1/+1
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: cleanup ops function pointersBruce Allan1-55/+55
The phy and nvm operations structures have function pointers that contain "phy" and "nvm" in the pointer names which are redundant since the structures are already obviously in phy and nvm structures. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: consolidate two dbug macros into one simpler oneBruce Allan1-46/+46
This patch depends on a previous one that cleans up redundant #includes. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21e1000e: improper return code signageBruce Allan1-1/+1
The e1000_get_cable_length_82577() should return a negative value upon error. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-20e1000e: remove unnecessary 82577 workaround causing link issuesBruce Allan1-10/+0
A workaround for pre-release versions of 82577 is causing link issues on some switches. The workaround is no longer needed on production parts so remove it. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-20e1000e: read of PHY register may access wrong page on 82578Bruce Allan1-24/+22
Remove unnecessary workaround that mistakenly does not perform a page select operation for PHY registers 29 and 30 (assuming these are the PHY debug port address and data registers) on 82578 which can cause reads of the Transmit with No Carrier Sense statistics register on page 778 to be read from an incorrect page. Also error out if the page select operation fails. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-29e1000e: rework disable K1 at 1000Mbps for 82577/82578Bruce Allan1-11/+4
This patch reworks a previous workaround (commit 7d3cabbcc) for an issue in hardware where noise on the interconnect between the MAC and PHY could be generated by a lower power mode (K1) at 1000Mbps resulting in bad packets. Disable K1 while at 1000 Mbps but keep it enabled for 10/100Mbps and when the cable is disconnected. The original version of this workaround was found to be incomplete. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-26e1000e: allow for swflag to be held over consecutive PHY accessesBruce Allan1-141/+328
PCH-based parts (82577/82578) and some ICH8-based parts (82566) need to hold the swflag (sw/fw/hw hardware semaphore) over consecutive PHY accesses in order to perform sw-driven PHY configuration during initialization to workaround known hardware issues (see follow-on patch). This patch provides new PHY read/write functions (and function pointers) that will allow accessing the PHY registers assuming the swflag has already been acquired. The actual PHY register access code has moved into helper functions that are called with a flag indicating whether or not the swflag has already been acquired and acquires/releases it if not. The functions called from within the updated PHY access functions had to be updated to assume the swflag was already acquired, and other functions that called those functions were also updated to acquire/release the swflag. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03e1000e: delay second read of PHY_STATUS register on failure of first readBruce Allan1-1/+6
Some PHYs may require two reads of the PHY_STATUS register to determine the link status. If the PHY is being accessed by another thread it is possible the first read could timeout and fail. In this case, put a delay in so the second read will pick up the correct link status. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03e1000e: PHY loopback broken on 82578Bruce Allan1-0/+5
PHY loopback on 82578 fails to work as a result of flushing the packets in the FIFO buffer in the link stall workaround. Don't perform the workaround if in PHY loopback mode. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-03e1000e: add support for 82577/82578 GbE LOM partsBruce Allan1-17/+682
This patch provides support for the next generation Intel desktop and mobile gigabit ethernet LOM adapters. These adapters are the follow-on parts to the LOMs tied to the prior ICH chipsets and are comprised of a MAC in the PCH chipset and an external PHY (82577 for mobile and 82578 for desktop versions). New features consist of PHY wakeup to save power by completely turning off the MAC while in Sx state, and 4K jumbo frames. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-21e1000e: sync change flow control variables with ixgbeBruce Allan1-2/+2
Sync flow control variables and usage model with that found in the ixgbe driver. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-21e1000e: commit speed/duplex changes for m88 PHYBruce Allan1-4/+4
Follow the convention used elsewhere in e1000e to 'commit' PHY changes instead of directly writing to the PHY CTRL register to reset it. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-09-03e1000e: add support for new 82574L partBruce Allan1-1/+108
This new part has the same feature set as previous parts with the addition of MSI-X support. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-03e1000e: add support for 82567LM-3 and 82567LF-3 (ICH10D) partsBruce Allan1-0/+85
Add support for new LOM devices on the latest generation ICHx platforms. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06e1000e: Add support for BM PHYs on ICH9Bruce Allan1-0/+278
This patch adds support for the BM PHY, a new PHY model being used on ICH9-based implementations. This new PHY exposes issues in the ICH9 silicon when receiving jumbo frames large enough to use more than a certain part of the Rx FIFO, and this unfortunately breaks packet split jumbo receives. For this reason we re-introduce (for affected adapters only) the jumbo single-skb receive routine back so that people who do wish to use jumbo frames on these ich9 platforms can do so. Part of this problem has to do with CPU sleep states and to make sure that all the wake up timings are correctly we force them with the recently merged pm_qos infrastructure written by Mark Gross. (See http://lkml.org/lkml/2007/10/4/400). To make code read a bit easier we introduce a _IS_ICH flag so that we don't need to do mac type checks over the code. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25e1000e: Fix HW Error on es2lan, ARP capture issue by BMCDavid Graham1-33/+40
Several components to this complex fix. The es2lan cards occasionally gave a "HW Error" especially when forcing speed. Some users also reported that the BMC stole ARP packets. The fixes include setting the proper SW_FW bits to tell the BMC that we're active and not do any un-initialization at all, so the setup routine is largely changed. Signed-off-by: David Graham <david.graham@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-03-28e1000e: reorganize PHY and flow control interfaceJeff Kirsher1-6/+6
This reorganization moves the PHY status into a separate struct. Flow Control setup is moved into this struct as well and frame size away from here into the adapter struct where its inly use is. The post-link-up code is now a separate function and moved out of the watchdog function itself. This allows us to track the es2lan restart issue a bit easier. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-28e1000e: reformat comment blocks, cosmetic changes onlyBruce Allan1-55/+97
Adjusting the comment blocks here to be code-style compliant. no code changes. Changed some copyright dates to 2008. Indentation fixes. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-24e1000e: fix spelling errors in commentsAuke Kok1-5/+5
Fix some spelling errors and inconsistencies in comment blocks. Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28netdev: ARRAY_SIZE() cleanupsAlejandro Martinez Ruiz1-2/+1
Convert array size calculations to use ARRAY_SIZE(). Signed-off-by: Alejandro Martinez Ruiz <alex@flawedcode.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10[E1000E]: New pci-express e1000 driver (currently for ICH9 devices only)Auke Kok1-0/+1773
This driver implements support for the ICH9 on-board LAN ethernet device. The device is similar to ICH8. The driver encompasses code to support 82571/2/3, es2lan and ICH8 devices as well, but those device IDs are disabled and will be "lifted" from the e1000 driver over one at a time once this driver receives some more live time. Changes to the last snapshot posted are exclusively in the internal hardware API organization. Many thanks to Jeff Garzik for jumping in and getting this organized with a keen eye on the future layout. [ Integrated napi_struct patch from Auke as well... -DaveM ] Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.