aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/8390 (unfollow)
AgeCommit message (Collapse)AuthorFilesLines
2020-03-06arm64: dts: ls1043a: FMan erratum A050385Madalin Bucur1-0/+2
The LS1043A SoC is affected by the A050385 erratum stating that FMAN DMA read or writes under heavy traffic load may cause FMAN internal resource leak thus stopping further packet processing. Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-06dt-bindings: net: FMan erratum A050385Madalin Bucur1-0/+7
FMAN DMA read or writes under heavy traffic load may cause FMAN internal resource leak; thus stopping further packet processing. The FMAN internal queue can overflow when FMAN splits single read or write transactions into multiple smaller transactions such that more than 17 AXI transactions are in flight from FMAN to interconnect. When the FMAN internal queue overflows, it can stall further packet processing. The issue can occur with any one of the following three conditions: 1. FMAN AXI transaction crosses 4K address boundary (Errata A010022) 2. FMAN DMA address for an AXI transaction is not 16 byte aligned, i.e. the last 4 bits of an address are non-zero 3. Scatter Gather (SG) frames have more than one SG buffer in the SG list and any one of the buffers, except the last buffer in the SG list has data size that is not a multiple of 16 bytes, i.e., other than 16, 32, 48, 64, etc. With any one of the above three conditions present, there is likelihood of stalled FMAN packet processing, especially under stress with multiple ports injecting line-rate traffic. To avoid situations that stall FMAN packet processing, all of the above three conditions must be avoided; therefore, configure the system with the following rules: 1. Frame buffers must not span a 4KB address boundary, unless the frame start address is 256 byte aligned 2. All FMAN DMA start addresses (for example, BMAN buffer address, FD[address] + FD[offset]) are 16B aligned 3. SG table and buffer addresses are 16B aligned and the size of SG buffers are multiple of 16 bytes, except for the last SG buffer that can be of any size. Additional workaround notes: - Address alignment of 64 bytes is recommended for maximally efficient system bus transactions (although 16 byte alignment is sufficient to avoid the stall condition) - To support frame sizes that are larger than 4K bytes, there are two options: 1. Large single buffer frames that span a 4KB page boundary can be converted into SG frames to avoid transaction splits at the 4KB boundary, 2. Align the large single buffer to 256B address boundaries, ensure that the frame address plus offset is 256B aligned. - If software generated SG frames have buffers that are unaligned and with random non-multiple of 16 byte lengths, before transmitting such frames via FMAN, frames will need to be copied into a new single buffer or multiple buffer SG frame that is compliant with the three rules listed above. Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-06netfilter: nft_chain_nat: inet family is missing module ownershipPablo Neira Ayuso1-0/+1
Set owner to THIS_MODULE, otherwise the nft_chain_nat module might be removed while there are still inet/nat chains in place. [ 117.942096] BUG: unable to handle page fault for address: ffffffffa0d5e040 [ 117.942101] #PF: supervisor read access in kernel mode [ 117.942103] #PF: error_code(0x0000) - not-present page [ 117.942106] PGD 200c067 P4D 200c067 PUD 200d063 PMD 3dc909067 PTE 0 [ 117.942113] Oops: 0000 [#1] PREEMPT SMP PTI [ 117.942118] CPU: 3 PID: 27 Comm: kworker/3:0 Not tainted 5.6.0-rc3+ #348 [ 117.942133] Workqueue: events nf_tables_trans_destroy_work [nf_tables] [ 117.942145] RIP: 0010:nf_tables_chain_destroy.isra.0+0x94/0x15a [nf_tables] [ 117.942149] Code: f6 45 54 01 0f 84 d1 00 00 00 80 3b 05 74 44 48 8b 75 e8 48 c7 c7 72 be de a0 e8 56 e6 2d e0 48 8b 45 e8 48 c7 c7 7f be de a0 <48> 8b 30 e8 43 e6 2d e0 48 8b 45 e8 48 8b 40 10 48 85 c0 74 5b 8b [ 117.942152] RSP: 0018:ffffc9000015be10 EFLAGS: 00010292 [ 117.942155] RAX: ffffffffa0d5e040 RBX: ffff88840be87fc2 RCX: 0000000000000007 [ 117.942158] RDX: 0000000000000007 RSI: 0000000000000086 RDI: ffffffffa0debe7f [ 117.942160] RBP: ffff888403b54b50 R08: 0000000000001482 R09: 0000000000000004 [ 117.942162] R10: 0000000000000000 R11: 0000000000000001 R12: ffff8883eda7e540 [ 117.942164] R13: dead000000000122 R14: dead000000000100 R15: ffff888403b3db80 [ 117.942167] FS: 0000000000000000(0000) GS:ffff88840e4c0000(0000) knlGS:0000000000000000 [ 117.942169] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 117.942172] CR2: ffffffffa0d5e040 CR3: 00000003e4c52002 CR4: 00000000001606e0 [ 117.942174] Call Trace: [ 117.942188] nf_tables_trans_destroy_work.cold+0xd/0x12 [nf_tables] [ 117.942196] process_one_work+0x1d6/0x3b0 [ 117.942200] worker_thread+0x45/0x3c0 [ 117.942203] ? process_one_work+0x3b0/0x3b0 [ 117.942210] kthread+0x112/0x130 [ 117.942214] ? kthread_create_worker_on_cpu+0x40/0x40 [ 117.942221] ret_from_fork+0x35/0x40 nf_tables_chain_destroy() crashes on module_put() because the module is gone. Fixes: d164385ec572 ("netfilter: nat: add inet family nat support") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-03-05mptcp: always include dack if possible.Paolo Abeni1-2/+17
Currently passive MPTCP socket can skip including the DACK option - if the peer sends data before accept() completes. The above happens because the msk 'can_ack' flag is set only after the accept() call. Such missing DACK option may cause - as per RFC spec - unwanted fallback to TCP. This change addresses the issue using the key material available in the current subflow, if any, to create a suitable dack option when msk ack seq is not yet available. v1 -> v2: - adavance the generated ack after the initial MPC packet Fixes: d22f4988ffec ("mptcp: process MP_CAPABLE data option") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-05net: nfc: fix bounds checking bugs on "pipe"Dan Carpenter1-3/+16
This is similar to commit 674d9de02aa7 ("NFC: Fix possible memory corruption when handling SHDLC I-Frame commands") and commit d7ee81ad09f0 ("NFC: nci: Add some bounds checking in nci_hci_cmd_received()") which added range checks on "pipe". The "pipe" variable comes skb->data[0] in nfc_hci_msg_rx_work(). It's in the 0-255 range. We're using it as the array index into the hdev->pipes[] array which has NFC_HCI_MAX_PIPES (128) members. Fixes: 118278f20aa8 ("NFC: hci: Add pipes table to reference them with a tuple {gate, host}") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-05veth: ignore peer tx_dropped when counting local rx_droppedJiang Lidong1-1/+1
When local NET_RX backlog is full due to traffic overrun, peer veth tx_dropped counter increases. At that time, list local veth stats, rx_dropped has double value of peer tx_dropped, even bigger than transmit packets by peer. In NET_RX softirq process, if any packet drop case happens, it increases dev's rx_dropped counter and returns NET_RX_DROP. At veth tx side, it records any error returned from peer netif_rx into local dev tx_dropped counter. In veth get stats process, it puts local dev rx_dropped and peer dev tx_dropped into together as local rx_drpped value. So that it shows double value of real dropped packets number in this case. This patch ignores peer tx_dropped when counting local rx_dropped, since peer tx_dropped is duplicated to local rx_dropped at most cases. Signed-off-by: Jiang Lidong <jianglidong3@jd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-05sfc: complete the next packet when we receive a timestampTom Zhao6-31/+78
We now ignore the "completion" event when using tx queue timestamping, and only pay attention to the two (high and low) timestamp events. The NIC will send a pair of timestamp events for every packet transmitted. The current firmware may merge the completion events, and it is possible that future versions may reorder the completion and timestamp events. As such the completion event is not useful. Without this patch in place a merged completion event on a queue with timestamping will cause a "spurious TX completion" error. This affects SFN8000-series adapters. Signed-off-by: Tom Zhao <tzhao@solarflare.com> Acked-by: Martin Habets <mhabets@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-05net: hns3: fix a not link up issue when fibre port supports autonegJian Shen1-1/+3
When fibre port supports auto-negotiation, the IMP(Intelligent Management Process) processes the speed of auto-negotiation and the user's speed separately. For below case, the port will get a not link up problem. step 1: disables auto-negotiation and sets speed to A, then the driver's MAC speed will be updated to A. step 2: enables auto-negotiation and MAC gets negotiated speed B, then the driver's MAC speed will be updated to B through querying in periodical task. step 3: MAC gets new negotiated speed A. step 4: disables auto-negotiation and sets speed to B before periodical task query new MAC speed A, the driver will ignore the speed configuration. This patch fixes it by skipping speed and duplex checking when fibre port supports auto-negotiation. Fixes: 22f48e24a23d ("net: hns3: add autoneg and change speed support for fibre port") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-05slip: make slhc_compress() more robust against malicious packetsEric Dumazet1-4/+10
Before accessing various fields in IPV4 network header and TCP header, make sure the packet : - Has IP version 4 (ip->version == 4) - Has not a silly network length (ip->ihl >= 5) - Is big enough to hold network and transport headers - Has not a silly TCP header size (th->doff >= sizeof(struct tcphdr) / 4) syzbot reported : BUG: KMSAN: uninit-value in slhc_compress+0x5b9/0x2e60 drivers/net/slip/slhc.c:270 CPU: 0 PID: 11728 Comm: syz-executor231 Not tainted 5.6.0-rc2-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x1c9/0x220 lib/dump_stack.c:118 kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:118 __msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215 slhc_compress+0x5b9/0x2e60 drivers/net/slip/slhc.c:270 ppp_send_frame drivers/net/ppp/ppp_generic.c:1637 [inline] __ppp_xmit_process+0x1902/0x2970 drivers/net/ppp/ppp_generic.c:1495 ppp_xmit_process+0x147/0x2f0 drivers/net/ppp/ppp_generic.c:1516 ppp_write+0x6bb/0x790 drivers/net/ppp/ppp_generic.c:512 do_loop_readv_writev fs/read_write.c:717 [inline] do_iter_write+0x812/0xdc0 fs/read_write.c:1000 compat_writev+0x2df/0x5a0 fs/read_write.c:1351 do_compat_pwritev64 fs/read_write.c:1400 [inline] __do_compat_sys_pwritev fs/read_write.c:1420 [inline] __se_compat_sys_pwritev fs/read_write.c:1414 [inline] __ia32_compat_sys_pwritev+0x349/0x3f0 fs/read_write.c:1414 do_syscall_32_irqs_on arch/x86/entry/common.c:339 [inline] do_fast_syscall_32+0x3c7/0x6e0 arch/x86/entry/common.c:410 entry_SYSENTER_compat+0x68/0x77 arch/x86/entry/entry_64_compat.S:139 RIP: 0023:0xf7f7cd99 Code: 90 e8 0b 00 00 00 f3 90 0f ae e8 eb f9 8d 74 26 00 89 3c 24 c3 90 90 90 90 90 90 90 90 90 90 90 90 51 52 55 89 e5 0f 34 cd 80 <5d> 5a 59 c3 90 90 90 90 eb 0d 90 90 90 90 90 90 90 90 90 90 90 90 RSP: 002b:00000000ffdb84ac EFLAGS: 00000217 ORIG_RAX: 000000000000014e RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00000000200001c0 RDX: 0000000000000001 RSI: 0000000000000000 RDI: 0000000000000003 RBP: 0000000040047459 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:144 [inline] kmsan_internal_poison_shadow+0x66/0xd0 mm/kmsan/kmsan.c:127 kmsan_slab_alloc+0x8a/0xe0 mm/kmsan/kmsan_hooks.c:82 slab_alloc_node mm/slub.c:2793 [inline] __kmalloc_node_track_caller+0xb40/0x1200 mm/slub.c:4401 __kmalloc_reserve net/core/skbuff.c:142 [inline] __alloc_skb+0x2fd/0xac0 net/core/skbuff.c:210 alloc_skb include/linux/skbuff.h:1051 [inline] ppp_write+0x115/0x790 drivers/net/ppp/ppp_generic.c:500 do_loop_readv_writev fs/read_write.c:717 [inline] do_iter_write+0x812/0xdc0 fs/read_write.c:1000 compat_writev+0x2df/0x5a0 fs/read_write.c:1351 do_compat_pwritev64 fs/read_write.c:1400 [inline] __do_compat_sys_pwritev fs/read_write.c:1420 [inline] __se_compat_sys_pwritev fs/read_write.c:1414 [inline] __ia32_compat_sys_pwritev+0x349/0x3f0 fs/read_write.c:1414 do_syscall_32_irqs_on arch/x86/entry/common.c:339 [inline] do_fast_syscall_32+0x3c7/0x6e0 arch/x86/entry/common.c:410 entry_SYSENTER_compat+0x68/0x77 arch/x86/entry/entry_64_compat.S:139 Fixes: b5451d783ade ("slip: Move the SLIP drivers") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-05netfilter: nf_tables: fix infinite loop when expr is not availableFlorian Westphal1-7/+3
nft will loop forever if the kernel doesn't support an expression: 1. nft_expr_type_get() appends the family specific name to the module list. 2. -EAGAIN is returned to nfnetlink, nfnetlink calls abort path. 3. abort path sets ->done to true and calls request_module for the expression. 4. nfnetlink replays the batch, we end up in nft_expr_type_get() again. 5. nft_expr_type_get attempts to append family-specific name. This one already exists on the list, so we continue 6. nft_expr_type_get adds the generic expression name to the module list. -EAGAIN is returned, nfnetlink calls abort path. 7. abort path encounters the family-specific expression which has 'done' set, so it gets removed. 8. abort path requests the generic expression name, sets done to true. 9. batch is replayed. If the expression could not be loaded, then we will end up back at 1), because the family-specific name got removed and the cycle starts again. Note that userspace can SIGKILL the nft process to stop the cycle, but the desired behaviour is to return an error after the generic expr name fails to load the expression. Fixes: eb014de4fd418 ("netfilter: nf_tables: autoload modules from the abort path") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-03-05netfilter: nf_tables: dump NFTA_CHAIN_FLAGS attributePablo Neira Ayuso1-0/+5
Missing NFTA_CHAIN_FLAGS netlink attribute when dumping basechain definitions. Fixes: c9626a2cbdb2 ("netfilter: nf_tables: add hardware offload support") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-03-03drivers/of/of_mdio.c:fix of_mdiobus_register()Dajun Jin1-0/+1
When registers a phy_device successful, should terminate the loop or the phy_device would be registered in other addr. If there are multiple PHYs without reg properties, it will go wrong. Signed-off-by: Dajun Jin <adajunjin@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03cxgb4: fix checks for max queues to allocateVishal Kulkarni1-22/+27
Hardware can support more than 8 queues currently limited by netif_get_num_default_rss_queues(). So, rework and fix checks for max number of queues to allocate. The checks should be based on how many are actually supported by hardware, OR the number of online cpus; whichever is lower. Fixes: 5952dde72307 ("cxgb4: set maximal number of default RSS queues") Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>" Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03phylink: Improve error message when validate failedHauke Mehrtens1-1/+7
This should improve the error message when the PHY validate in the MAC driver failed. I ran into this problem multiple times that I put wrong interface values into the device tree and was searching why it is failing with -22 (-EINVAL). This should make it easier to spot the problem. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03net: phy: bcm63xx: fix OOPS due to missing driver nameJonas Gorski1-0/+1
719655a14971 ("net: phy: Replace phy driver features u32 with link_mode bitmap") was a bit over-eager and also removed the second phy driver's name, resulting in a nasty OOPS on registration: [ 1.319854] CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 804dd50c, ra == 804dd4f0 [ 1.330859] Oops[#1]: [ 1.333138] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.4.22 #0 [ 1.339217] $ 0 : 00000000 00000001 87ca7f00 805c1874 [ 1.344590] $ 4 : 00000000 00000047 00585000 8701f800 [ 1.349965] $ 8 : 8701f800 804f4a5c 00000003 64726976 [ 1.355341] $12 : 00000001 00000000 00000000 00000114 [ 1.360718] $16 : 87ca7f80 00000000 00000000 80639fe4 [ 1.366093] $20 : 00000002 00000000 806441d0 80b90000 [ 1.371470] $24 : 00000000 00000000 [ 1.376847] $28 : 87c1e000 87c1fda0 80b90000 804dd4f0 [ 1.382224] Hi : d1c8f8da [ 1.385180] Lo : 5518a480 [ 1.388182] epc : 804dd50c kset_find_obj+0x3c/0x114 [ 1.393345] ra : 804dd4f0 kset_find_obj+0x20/0x114 [ 1.398530] Status: 10008703 KERNEL EXL IE [ 1.402833] Cause : 00800008 (ExcCode 02) [ 1.406952] BadVA : 00000000 [ 1.409913] PrId : 0002a075 (Broadcom BMIPS4350) [ 1.414745] Modules linked in: [ 1.417895] Process swapper/0 (pid: 1, threadinfo=(ptrval), task=(ptrval), tls=00000000) [ 1.426214] Stack : 87cec000 80630000 80639370 80640658 80640000 80049af4 80639fe4 8063a0d8 [ 1.434816] 8063a0d8 802ef078 00000002 00000000 806441d0 80b90000 8063a0d8 802ef114 [ 1.443417] 87cea0de 87c1fde0 00000000 804de488 87cea000 8063a0d8 8063a0d8 80334e48 [ 1.452018] 80640000 8063984c 80639bf4 00000000 8065de48 00000001 8063a0d8 80334ed0 [ 1.460620] 806441d0 80b90000 80b90000 802ef164 8065dd70 80620000 80b90000 8065de58 [ 1.469222] ... [ 1.471734] Call Trace: [ 1.474255] [<804dd50c>] kset_find_obj+0x3c/0x114 [ 1.479141] [<802ef078>] driver_find+0x1c/0x44 [ 1.483665] [<802ef114>] driver_register+0x74/0x148 [ 1.488719] [<80334e48>] phy_driver_register+0x9c/0xd0 [ 1.493968] [<80334ed0>] phy_drivers_register+0x54/0xe8 [ 1.499345] [<8001061c>] do_one_initcall+0x7c/0x1f4 [ 1.504374] [<80644ed8>] kernel_init_freeable+0x1d4/0x2b4 [ 1.509940] [<804f4e24>] kernel_init+0x10/0xf8 [ 1.514502] [<80018e68>] ret_from_kernel_thread+0x14/0x1c [ 1.520040] Code: 1060000c 02202025 90650000 <90810000> 24630001 14250004 24840001 14a0fffb 90650000 [ 1.530061] [ 1.531698] ---[ end trace d52f1717cd29bdc8 ]--- Fix it by readding the name. Fixes: 719655a14971 ("net: phy: Replace phy driver features u32 with link_mode bitmap") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03devlink: remove trigger command from devlink-region.rstJacob Keller1-3/+0
The devlink trigger command does not exist. While rewriting the documentation for devlink into the reStructuredText format, documentation for the trigger command was accidentally merged in. This occurred because the author was also working on a potential extension to devlink regions which included this trigger command, and accidentally squashed the documentation incorrectly. Further review eventually settled on using the previously unused "new" command instead of creating a new trigger command. Fix this by removing mention of the trigger command from the documentation. Fixes: 0b0f945f5458 ("devlink: add a file documenting devlink regions", 2020-01-10) Noticed-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-04netfilter: nft_tunnel: add missing attribute validation for tunnelsJakub Kicinski1-0/+2
Add missing attribute validation for tunnel source and destination ports to the netlink policy. Fixes: af308b94a2a4 ("netfilter: nf_tables: add tunnel support") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-03-04netfilter: nft_payload: add missing attribute validation for payload csum flagsJakub Kicinski1-0/+1
Add missing attribute validation for NFTA_PAYLOAD_CSUM_FLAGS to the netlink policy. Fixes: 1814096980bb ("netfilter: nft_payload: layer 4 checksum adjustment for pseudoheader fields") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-03-04netfilter: cthelper: add missing attribute validation for cthelperJakub Kicinski1-0/+2
Add missing attribute validation for cthelper to the netlink policy. Fixes: 12f7a505331e ("netfilter: add user-space connection tracking helper infrastructure") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-03-04netfilter: nf_tables: free flowtable hooks on hook register errorFlorian Westphal1-1/+6
If hook registration fails, the hooks allocated via nft_netdev_hook_alloc need to be freed. We can't change the goto label to 'goto 5' -- while it does fix the memleak it does cause a warning splat from the netfilter core (the hooks were not registered). Fixes: 3f0465a9ef02 ("netfilter: nf_tables: dynamically allocate hooks per net_device in flowtables") Reported-by: syzbot+a2ff6fa45162a5ed4dd3@syzkaller.appspotmail.com Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-03-04netfilter: x_tables: xt_mttg_seq_next should increase position indexVasily Averin1-3/+3
If .next function does not change position index, following .show function will repeat output related to current position index. Without patch: # dd if=/proc/net/ip_tables_matches # original file output conntrack conntrack conntrack recent recent icmp udplite udp tcp 0+1 records in 0+1 records out 65 bytes copied, 5.4074e-05 s, 1.2 MB/s # dd if=/proc/net/ip_tables_matches bs=62 skip=1 dd: /proc/net/ip_tables_matches: cannot skip to specified offset cp <<< end of last line tcp <<< and then unexpected whole last line once again 0+1 records in 0+1 records out 7 bytes copied, 0.000102447 s, 68.3 kB/s Cc: stable@vger.kernel.org Fixes: 1f4aace60b0e ("fs/seq_file.c: simplify seq_file iteration code ...") Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283 Signed-off-by: Vasily Averin <vvs@virtuozzo.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-03-04netfilter: xt_recent: recent_seq_next should increase position indexVasily Averin1-1/+1
If .next function does not change position index, following .show function will repeat output related to current position index. Without the patch: # dd if=/proc/net/xt_recent/SSH # original file outpt src=127.0.0.4 ttl: 0 last_seen: 6275444819 oldest_pkt: 1 6275444819 src=127.0.0.2 ttl: 0 last_seen: 6275438906 oldest_pkt: 1 6275438906 src=127.0.0.3 ttl: 0 last_seen: 6275441953 oldest_pkt: 1 6275441953 0+1 records in 0+1 records out 204 bytes copied, 6.1332e-05 s, 3.3 MB/s Read after lseek into middle of last line (offset 140 in example below) generates expected end of last line and then unexpected whole last line once again # dd if=/proc/net/xt_recent/SSH bs=140 skip=1 dd: /proc/net/xt_recent/SSH: cannot skip to specified offset 127.0.0.3 ttl: 0 last_seen: 6275441953 oldest_pkt: 1 6275441953 src=127.0.0.3 ttl: 0 last_seen: 6275441953 oldest_pkt: 1 6275441953 0+1 records in 0+1 records out 132 bytes copied, 6.2487e-05 s, 2.1 MB/s Cc: stable@vger.kernel.org Fixes: 1f4aace60b0e ("fs/seq_file.c: simplify seq_file iteration code ...") Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283 Signed-off-by: Vasily Averin <vvs@virtuozzo.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-03-04netfilter: synproxy: synproxy_cpu_seq_next should increase position indexVasily Averin1-1/+1
If .next function does not change position index, following .show function will repeat output related to current position index. Cc: stable@vger.kernel.org Fixes: 1f4aace60b0e ("fs/seq_file.c: simplify seq_file iteration code ...") Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283 Signed-off-by: Vasily Averin <vvs@virtuozzo.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-03-04netfilter: nf_conntrack: ct_cpu_seq_next should increase position indexVasily Averin1-1/+1
If .next function does not change position index, following .show function will repeat output related to current position index. Cc: stable@vger.kernel.org Fixes: 1f4aace60b0e ("fs/seq_file.c: simplify seq_file iteration code ...") Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283 Signed-off-by: Vasily Averin <vvs@virtuozzo.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-03-03docs: networking: net_failover: Fix a few typosJonathan Neuschäfer1-3/+3
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03net: dsa: fix phylink_start()/phylink_stop() callsRussell King3-12/+30
Place phylink_start()/phylink_stop() inside dsa_port_enable() and dsa_port_disable(), which ensures that we call phylink_stop() before tearing down phylink - which is a documented requirement. Failure to do so can cause use-after-free bugs. Fixes: 0e27921816ad ("net: dsa: Use PHYLINK for the CPU/DSA ports") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03selftests/net/fib_tests: update addr_metric_test for peer route testingHangbin Liu1-3/+31
This patch update {ipv4, ipv6}_addr_metric_test with 1. Set metric of address with peer route and see if the route added correctly. 2. Modify metric and peer address for peer route and see if the route changed correctly. Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03net/ipv6: remove the old peer route if change it to a new oneHangbin Liu1-4/+17
When we modify the peer route and changed it to a new one, we should remove the old route first. Before the fix: + ip addr add dev dummy1 2001:db8::1 peer 2001:db8::2 + ip -6 route show dev dummy1 2001:db8::1 proto kernel metric 256 pref medium 2001:db8::2 proto kernel metric 256 pref medium + ip addr change dev dummy1 2001:db8::1 peer 2001:db8::3 + ip -6 route show dev dummy1 2001:db8::1 proto kernel metric 256 pref medium 2001:db8::2 proto kernel metric 256 pref medium After the fix: + ip addr change dev dummy1 2001:db8::1 peer 2001:db8::3 + ip -6 route show dev dummy1 2001:db8::1 proto kernel metric 256 pref medium 2001:db8::3 proto kernel metric 256 pref medium This patch depend on the previous patch "net/ipv6: need update peer route when modify metric" to update new peer route after delete old one. Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03net/ipv6: need update peer route when modify metricHangbin Liu1-4/+16
When we modify the route metric, the peer address's route need also be updated. Before the fix: + ip addr add dev dummy1 2001:db8::1 peer 2001:db8::2 metric 60 + ip -6 route show dev dummy1 2001:db8::1 proto kernel metric 60 pref medium 2001:db8::2 proto kernel metric 60 pref medium + ip addr change dev dummy1 2001:db8::1 peer 2001:db8::2 metric 61 + ip -6 route show dev dummy1 2001:db8::1 proto kernel metric 61 pref medium 2001:db8::2 proto kernel metric 60 pref medium After the fix: + ip addr change dev dummy1 2001:db8::1 peer 2001:db8::2 metric 61 + ip -6 route show dev dummy1 2001:db8::1 proto kernel metric 61 pref medium 2001:db8::2 proto kernel metric 61 pref medium Fixes: 8308f3ff1753 ("net/ipv6: Add support for specifying metric of connected routes") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03nfc: add missing attribute validation for vendor subcommandJakub Kicinski1-0/+2
Add missing attribute validation for vendor subcommand attributes to the netlink policy. Fixes: 9e58095f9660 ("NFC: netlink: Implement vendor command support") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03nfc: add missing attribute validation for deactivate targetJakub Kicinski1-0/+1
Add missing attribute validation for NFC_ATTR_TARGET_INDEX to the netlink policy. Fixes: 4d63adfe12dd ("NFC: Add NFC_CMD_DEACTIVATE_TARGET support") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03nfc: add missing attribute validation for SE APIJakub Kicinski1-0/+1
Add missing attribute validation for NFC_ATTR_SE_INDEX to the netlink policy. Fixes: 5ce3f32b5264 ("NFC: netlink: SE API implementation") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03tipc: add missing attribute validation for MTU propertyJakub Kicinski1-0/+1
Add missing attribute validation for TIPC_NLA_PROP_MTU to the netlink policy. Fixes: 901271e0403a ("tipc: implement configuration of UDP media MTU") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03team: add missing attribute validation for array indexJakub Kicinski1-0/+1
Add missing attribute validation for TEAM_ATTR_OPTION_ARRAY_INDEX to the netlink policy. Fixes: b13033262d24 ("team: introduce array options") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03team: add missing attribute validation for port ifindexJakub Kicinski1-0/+1
Add missing attribute validation for TEAM_ATTR_OPTION_PORT_IFINDEX to the netlink policy. Fixes: 80f7c6683fe0 ("team: add support for per-port options") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03net: taprio: add missing attribute validation for txtime delayJakub Kicinski1-0/+1
Add missing attribute validation for TCA_TAPRIO_ATTR_TXTIME_DELAY to the netlink policy. Fixes: 4cfd5779bd6e ("taprio: Add support for txtime-assist mode") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03net: fq: add missing attribute validation for orphan maskJakub Kicinski1-0/+1
Add missing attribute validation for TCA_FQ_ORPHAN_MASK to the netlink policy. Fixes: 06eb395fa985 ("pkt_sched: fq: better control of DDOS traffic") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03openvswitch: add missing attribute validation for hashJakub Kicinski1-0/+1
Add missing attribute validation for OVS_PACKET_ATTR_HASH to the netlink policy. Fixes: bd1903b7c459 ("net: openvswitch: add hash info to upcall") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Greg Rose <gvrose8192@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03macsec: add missing attribute validation for portJakub Kicinski1-0/+1
Add missing attribute validation for IFLA_MACSEC_PORT to the netlink policy. Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03can: add missing attribute validation for terminationJakub Kicinski1-0/+1
Add missing attribute validation for IFLA_CAN_TERMINATION to the netlink policy. Fixes: 12a6075cabc0 ("can: dev: add CAN interface termination API") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03nl802154: add missing attribute validation for dev_typeJakub Kicinski1-0/+1
Add missing attribute type validation for IEEE802154_ATTR_DEV_TYPE to the netlink policy. Fixes: 90c049b2c6ae ("ieee802154: interface type to be added") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03nl802154: add missing attribute validationJakub Kicinski1-0/+5
Add missing attribute validation for several u8 types. Fixes: 2c21d11518b6 ("net: add NL802154 interface for configuration of 802.15.4 devices") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03fib: add missing attribute validation for tun_idJakub Kicinski1-0/+1
Add missing netlink policy entry for FRA_TUN_ID. Fixes: e7030878fc84 ("fib: Add fib rule match on tunnel id") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03devlink: validate length of region addr/lenJakub Kicinski1-0/+2
DEVLINK_ATTR_REGION_CHUNK_ADDR and DEVLINK_ATTR_REGION_CHUNK_LEN lack entries in the netlink policy. Corresponding nla_get_u64()s may read beyond the end of the message. Fixes: 4e54795a27f5 ("devlink: Add support for region snapshot read command") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03devlink: validate length of param valuesJakub Kicinski1-12/+19
DEVLINK_ATTR_PARAM_VALUE_DATA may have different types so it's not checked by the normal netlink policy. Make sure the attribute length is what we expect. Fixes: e3b7ca18ad7b ("devlink: Add param set command") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-03mt76: fix array overflow on receiving too many fragments for a packetFelix Fietkau1-3/+6
If the hardware receives an oversized packet with too many rx fragments, skb_shinfo(skb)->frags can overflow and corrupt memory of adjacent pages. This becomes especially visible if it corrupts the freelist pointer of a slab page. Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2020-03-01bnxt_en: fix error handling when flashing from fileEdwin Peer1-13/+11
After bnxt_hwrm_do_send_message() was updated to return standard error codes in a recent commit, a regression in bnxt_flash_package_from_file() was introduced. The return value does not properly reflect all possible firmware errors when calling firmware to flash the package. Fix it by consolidating all errors in one local variable rc instead of having 2 variables for different errors. Fixes: d4f1420d3656 ("bnxt_en: Convert error code in firmware message response to standard code.") Signed-off-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-01bnxt_en: reinitialize IRQs when MTU is modifiedVasundhara Volam1-2/+2
MTU changes may affect the number of IRQs so we must call bnxt_close_nic()/bnxt_open_nic() with the irq_re_init parameter set to true. The reason is that a larger MTU may require aggregation rings not needed with smaller MTU. We may not be able to allocate the required number of aggregation rings and so we reduce the number of channels which will change the number of IRQs. Without this patch, it may crash eventually in pci_disable_msix() when the IRQs are not properly unwound. Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-01net: phy: avoid clearing PHY interrupts twice in irq handlerHeiner Kallweit2-1/+3
On all PHY drivers that implement did_interrupt() reading the interrupt status bits clears them. This means we may loose an interrupt that is triggered between calling did_interrupt() and phy_clear_interrupt(). As part of the fix make it a requirement that did_interrupt() clears the interrupt. The Fixes tag refers to the first commit where the patch applies cleanly. Fixes: 49644e68f472 ("net: phy: add callback for custom interrupt handler to struct phy_driver") Reported-by: Michael Walle <michael@walle.cc> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-29net: dsa: sja1105: Don't destroy not-yet-created xmit_workerVladimir Oltean1-1/+2
Fixes the following NULL pointer dereference on PHY connect error path teardown: [ 2.291010] sja1105 spi0.1: Probed switch chip: SJA1105T [ 2.310044] sja1105 spi0.1: Enabled switch tagging [ 2.314970] fsl-gianfar soc:ethernet@2d90000 eth2: error -19 setting up slave phy [ 2.322463] 8<--- cut here --- [ 2.325497] Unable to handle kernel NULL pointer dereference at virtual address 00000018 [ 2.333555] pgd = (ptrval) [ 2.336241] [00000018] *pgd=00000000 [ 2.339797] Internal error: Oops: 5 [#1] SMP ARM [ 2.344384] Modules linked in: [ 2.347420] CPU: 1 PID: 64 Comm: kworker/1:1 Not tainted 5.5.0-rc5 #1 [ 2.353820] Hardware name: Freescale LS1021A [ 2.358070] Workqueue: events deferred_probe_work_func [ 2.363182] PC is at kthread_destroy_worker+0x4/0x74 [ 2.368117] LR is at sja1105_teardown+0x70/0xb4 [ 2.372617] pc : [<c036cdd4>] lr : [<c0b89238>] psr: 60000013 [ 2.378845] sp : eeac3d30 ip : eeab1900 fp : eef45480 [ 2.384036] r10: eef4549c r9 : 00000001 r8 : 00000000 [ 2.389227] r7 : eef527c0 r6 : 00000034 r5 : ed8ddd0c r4 : ed8ddc40 [ 2.395714] r3 : 00000000 r2 : 00000000 r1 : eef4549c r0 : 00000000 [ 2.402204] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none [ 2.409297] Control: 10c5387d Table: 8020406a DAC: 00000051 [ 2.415008] Process kworker/1:1 (pid: 64, stack limit = 0x(ptrval)) [ 2.421237] Stack: (0xeeac3d30 to 0xeeac4000) [ 2.612635] [<c036cdd4>] (kthread_destroy_worker) from [<c0b89238>] (sja1105_teardown+0x70/0xb4) [ 2.621379] [<c0b89238>] (sja1105_teardown) from [<c10717fc>] (dsa_switch_teardown.part.1+0x48/0x74) [ 2.630467] [<c10717fc>] (dsa_switch_teardown.part.1) from [<c1072438>] (dsa_register_switch+0x8b0/0xbf4) [ 2.639984] [<c1072438>] (dsa_register_switch) from [<c0b89c30>] (sja1105_probe+0x2ac/0x464) [ 2.648378] [<c0b89c30>] (sja1105_probe) from [<c0b11a5c>] (spi_drv_probe+0x7c/0xa0) [ 2.656081] [<c0b11a5c>] (spi_drv_probe) from [<c0a26ab8>] (really_probe+0x208/0x480) [ 2.663871] [<c0a26ab8>] (really_probe) from [<c0a26f0c>] (driver_probe_device+0x78/0x1c4) [ 2.672093] [<c0a26f0c>] (driver_probe_device) from [<c0a24c48>] (bus_for_each_drv+0x80/0xc4) [ 2.680574] [<c0a24c48>] (bus_for_each_drv) from [<c0a26810>] (__device_attach+0xd0/0x168) [ 2.688794] [<c0a26810>] (__device_attach) from [<c0a259d8>] (bus_probe_device+0x84/0x8c) [ 2.696927] [<c0a259d8>] (bus_probe_device) from [<c0a25f24>] (deferred_probe_work_func+0x84/0xc4) [ 2.705842] [<c0a25f24>] (deferred_probe_work_func) from [<c03667b0>] (process_one_work+0x22c/0x560) [ 2.714926] [<c03667b0>] (process_one_work) from [<c0366d8c>] (worker_thread+0x2a8/0x5d4) [ 2.723059] [<c0366d8c>] (worker_thread) from [<c036cf94>] (kthread+0x150/0x154) [ 2.730416] [<c036cf94>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c) Checking for NULL pointer is correct because the per-port xmit kernel threads are created in sja1105_probe immediately after calling dsa_register_switch. Fixes: a68578c20a96 ("net: dsa: Make deferred_xmit private to sja1105") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.