| Age | Commit message (Collapse) | Author | Files | Lines | |
|---|---|---|---|---|---|
| 2020-02-11 | net: ena: ena-com.c: prevent NULL pointer dereference |   Arthur Kiyanovski | 1 | -0/+5 | |
| comp_ctx can be NULL in a very rare case when an admin command is executed during the execution of ena_remove(). The bug scenario is as follows: * ena_destroy_device() sets the comp_ctx to be NULL * An admin command is executed before executing unregister_netdev(), this can still happen because our device can still receive callbacks from the netdev infrastructure such as ethtool commands. * When attempting to access the comp_ctx, the bug occurs since it's set to NULL Fix: Added a check that comp_ctx is not NULL Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2020-02-11 | net: ena: ethtool: use correct value for crc32 hash |   Sameeh Jubran | 1 | -2/+2 | |
| Up till kernel 4.11 there was no enum defined for crc32 hash in ethtool, thus the xor enum was used for supporting crc32. Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2020-02-11 | net: ena: make ena rxfh support ETH_RSS_HASH_NO_CHANGE | Arthur Kiyanovski | 3 | -0/+16 | |
| As the name suggests ETH_RSS_HASH_NO_CHANGE is received upon changing the key or indirection table using ethtool while keeping the same hash function. Also add a function for retrieving the current hash function from the ena-com layer. Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: Saeed Bshara <saeedb@amazon.com> Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2020-02-11 | net: ena: fix corruption of dev_idx_to_host_tbl | Arthur Kiyanovski | 1 | -28/+0 | |
| The function ena_com_ind_tbl_convert_from_device() has an overflow bug as explained below. Either way, this function is not needed at all since we don't retrieve the indirection table from the device at any point which means that this conversion is not needed. The bug: The for loop iterates over all io_sq_queues, when passing the actual number of used queues the io_sq_queues[i].idx equals 0 since they are uninitialized which results in the following code to be executed till the end of the loop: dev_idx_to_host_tbl[0] = i; This results dev_idx_to_host_tbl[0] in being equal to ENA_TOTAL_NUM_QUEUES - 1. Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2020-02-11 | net: ena: fix incorrectly saving queue numbers when setting RSS indirection table | Arthur Kiyanovski | 2 | -1/+25 | |
| The indirection table has the indices of the Rx queues. When we store it during set indirection operation, we convert the indices to our internal representation of the indices. Our internal representation of the indices is: even indices for Tx and uneven indices for Rx, where every Tx/Rx pair are in a consecutive order starting from 0. For example if the driver has 3 queues (3 for Tx and 3 for Rx) then the indices are as follows: 0 1 2 3 4 5 Tx Rx Tx Rx Tx Rx The BUG: The issue is that when we satisfy a get request for the indirection table, we don't convert the indices back to the original representation. The FIX: Simply apply the inverse function for the indices of the indirection table after we set it. Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2020-02-11 | net: ena: rss: store hash function as values and not bits | Arthur Kiyanovski | 1 | -1/+5 | |
| The device receives, stores and retrieves the hash function value as bits and not as their enum value. The bug: * In ena_com_set_hash_function() we set cmd.u.flow_hash_func.selected_func to the bit value of rss->hash_func. (1 << rss->hash_func) * In ena_com_get_hash_function() we retrieve the hash function and store it's bit value in rss->hash_func. (Now the bit value of rss->hash_func is stored in rss->hash_func instead of it's enum value) The fix: This commit fixes the issue by converting the retrieved hash function values from the device to the matching enum value of the set bit using ffs(). ffs() finds the first set bit's index in a word. Since the function returns 1 for the LSB's index, we need to subtract 1 from the returned value (note that BIT(0) is 1). Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2020-02-11 | net: ena: rss: fix failure to get indirection table | Sameeh Jubran | 1 | -0/+14 | |
| On old hardware, getting / setting the hash function is not supported while gettting / setting the indirection table is. This commit enables us to still show the indirection table on older hardwares by setting the hash function and key to NULL. Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2020-02-11 | net: ena: rss: do not allocate key when not supported | Sameeh Jubran | 1 | -3/+21 | |
| Currently we allocate the key whether the device supports setting the key or not. This commit adds a check to the allocation function and handles the error accordingly. Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2020-02-11 | net: ena: fix incorrect default RSS key | Arthur Kiyanovski | 2 | -0/+16 | |
| Bug description: When running "ethtool -x <if_name>" the key shows up as all zeros. When we use "ethtool -X <if_name> hfunc toeplitz hkey <some:random:key>" to set the key and then try to retrieve it using "ethtool -x <if_name>" then we return the correct key because we return the one we saved. Bug cause: We don't fetch the key from the device but instead return the key that we have saved internally which is by default set to zero upon allocation. Fix: This commit fixes the issue by initializing the key to a random value using netdev_rss_key_fill(). Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2020-02-11 | net: ena: add missing ethtool TX timestamping indication | Arthur Kiyanovski | 1 | -0/+1 | |
| Current implementation of the driver calls skb_tx_timestamp()to add a software tx timestamp to the skb, however the software-transmit capability is not reported in ethtool -T. This commit updates the ethtool structure to report the software-transmit capability in ethtool -T using the standard ethtool_op_get_ts_info(). This function reports all software timestamping capabilities (tx and rx), as well as setting phc_index = -1. phc_index is the index of the PTP hardware clock device that will be used for hardware timestamps. Since we don't have such a device in ENA, using the default -1 value is the correct setting. Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Ezequiel Lara Gomez <ezegomez@amazon.com> Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2020-02-11 | net: ena: fix uses of round_jiffies() | Arthur Kiyanovski | 1 | -3/+3 | |
| >From the documentation of round_jiffies(): "Rounds a time delta in the future (in jiffies) up or down to (approximately) full seconds. This is useful for timers for which the exact time they fire does not matter too much, as long as they fire approximately every X seconds. By rounding these timers to whole seconds, all such timers will fire at the same time, rather than at various times spread out. The goal of this is to have the CPU wake up less, which saves power." There are 2 parts to this patch: ================================ Part 1: ------- In our case we need timer_service to be called approximately every X=1 seconds, and the exact time does not matter, so using round_jiffies() is the right way to go. Therefore we add round_jiffies() to the mod_timer() in ena_timer_service(). Part 2: ------- round_jiffies() is used in check_for_missing_keep_alive() when getting the jiffies of the expiration of the keep_alive timeout. Here it is actually a mistake to use round_jiffies() because we want the exact time when keep_alive should expire and not an approximate rounded time, which can cause early, false positive, timeouts. Therefore we remove round_jiffies() in the calculation of keep_alive_expired() in check_for_missing_keep_alive(). Fixes: 82ef30f13be0 ("net: ena: add hardware hints capability to the driver") Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2020-02-11 | net: ena: fix potential crash when rxfh key is NULL | Arthur Kiyanovski | 1 | -8/+9 | |
| When ethtool -X is called without an hkey, ena_com_fill_hash_function() is called with key=NULL, which is passed to memcpy causing a crash. This commit fixes this issue by checking key is not NULL. Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-12-27 | net: ena: remove set but not used variable 'rx_ring' |   YueHaibing | 1 | -3/+0 | |
| drivers/net/ethernet/amazon/ena/ena_netdev.c: In function ena_xdp_xmit_buff: drivers/net/ethernet/amazon/ena/ena_netdev.c:316:19: warning: variable rx_ring set but not used [-Wunused-but-set-variable] commit 548c4940b9f1 ("net: ena: Implement XDP_TX action") left behind this unused variable. Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-12-22 | Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net |   David S. Miller | 3 | -18/+18 | |
| Mere overlapping changes in the conflicts here. Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-12-20 | net: ena: fix issues in setting interrupt moderation params in ethtool | Arthur Kiyanovski | 1 | -14/+10 | |
| Issue 1: -------- Reproduction steps: 1. sudo ethtool -C eth0 rx-usecs 128 2. sudo ethtool -C eth0 adaptive-rx on 3. sudo ethtool -C eth0 adaptive-rx off 4. ethtool -c eth0 expected output: rx-usecs 128 actual output: rx-usecs 0 Reason for issue: In stage 3, ethtool userspace calls first the ena_get_coalesce() handler to get the current value of all properties, and then the ena_set_coalesce() handler. When ena_get_coalesce() is called the adaptive interrupt moderation is still on. There is an if in the code that returns the rx_coalesce_usecs only if the adaptive interrupt moderation is off. And since it is still on, rx_coalesce_usecs is not set, meaning it stays 0. Solution to issue: Remove this if static interrupt moderation intervals have nothing to do with dynamic ones. Issue 2: -------- Reproduction steps: 1. sudo ethtool -C eth0 adaptive-rx on 2. sudo ethtool -C eth0 rx-usecs 128 3. ethtool -c eth0 expected output: rx-usecs 128 actual output: rx-usecs 0 Reason for issue: In stage 2, when ena_set_coalesce() is called, the handler tests if rx adaptive interrupt moderation is on, and if it is, it returns before getting to the part in the function that sets the rx non-adaptive interrupt moderation interval. Solution to issue: Remove the return from the function when rx adaptive interrupt moderation is on. Also cleaned up the fixed code in ena_set_coalesce by grouping together adaptive interrupt moderation toggling, and using && instead of nested ifs. Fixes: b3db86dc4b82 ("net: ena: reimplement set/get_coalesce()") Fixes: 0eda847953d8 ("net: ena: fix retrieval of nonadaptive interrupt moderation intervals") Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-12-20 | net: ena: fix default tx interrupt moderation interval | Arthur Kiyanovski | 1 | -1/+1 | |
| Current default non-adaptive tx interrupt moderation interval is 196 us. This value is too high and might cause the tx queue to fill up. In this commit we set the default non-adaptive tx interrupt moderation interval to 64 us in order to: 1. Reduce the probability of the queue filling-up (when compared to the current default value of 196 us). 2. Reduce unnecessary tx interrupt overhead (which happens if we set the default tx interval to 0). We determined experimentally that 64 us is an optimal value that reduces interrupt rate by more than 20% without affecting performance. Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-12-12 | netdev: pass the stuck queue to the timeout handler |   Michael S. Tsirkin | 1 | -1/+1 | |
| This allows incrementing the correct timeout statistic without any mess. Down the road, devices can learn to reset just the specific queue. The patch was generated with the following script: use strict; use warnings; our $^I = '.bak'; my @work = ( ["arch/m68k/emu/nfeth.c", "nfeth_tx_timeout"], ["arch/um/drivers/net_kern.c", "uml_net_tx_timeout"], ["arch/um/drivers/vector_kern.c", "vector_net_tx_timeout"], ["arch/xtensa/platforms/iss/network.c", "iss_net_tx_timeout"], ["drivers/char/pcmcia/synclink_cs.c", "hdlcdev_tx_timeout"], ["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"], ["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"], ["drivers/message/fusion/mptlan.c", "mpt_lan_tx_timeout"], ["drivers/misc/sgi-xp/xpnet.c", "xpnet_dev_tx_timeout"], ["drivers/net/appletalk/cops.c", "cops_timeout"], ["drivers/net/arcnet/arcdevice.h", "arcnet_timeout"], ["drivers/net/arcnet/arcnet.c", "arcnet_timeout"], ["drivers/net/arcnet/com20020.c", "arcnet_timeout"], ["drivers/net/ethernet/3com/3c509.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c515.c", "corkscrew_timeout"], ["drivers/net/ethernet/3com/3c574_cs.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c589_cs.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"], ["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"], ["drivers/net/ethernet/3com/typhoon.c", "typhoon_tx_timeout"], ["drivers/net/ethernet/8390/8390.h", "ei_tx_timeout"], ["drivers/net/ethernet/8390/8390.h", "eip_tx_timeout"], ["drivers/net/ethernet/8390/8390.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/8390p.c", "eip_tx_timeout"], ["drivers/net/ethernet/8390/ax88796.c", "ax_ei_tx_timeout"], ["drivers/net/ethernet/8390/axnet_cs.c", "axnet_tx_timeout"], ["drivers/net/ethernet/8390/etherh.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/hydra.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/mac8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/mcf8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/lib8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/ne2k-pci.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/pcnet_cs.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/smc-ultra.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/wd.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/zorro8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/adaptec/starfire.c", "tx_timeout"], ["drivers/net/ethernet/agere/et131x.c", "et131x_tx_timeout"], ["drivers/net/ethernet/allwinner/sun4i-emac.c", "emac_timeout"], ["drivers/net/ethernet/alteon/acenic.c", "ace_watchdog"], ["drivers/net/ethernet/amazon/ena/ena_netdev.c", "ena_tx_timeout"], ["drivers/net/ethernet/amd/7990.h", "lance_tx_timeout"], ["drivers/net/ethernet/amd/7990.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/a2065.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/am79c961a.c", "am79c961_timeout"], ["drivers/net/ethernet/amd/amd8111e.c", "amd8111e_tx_timeout"], ["drivers/net/ethernet/amd/ariadne.c", "ariadne_tx_timeout"], ["drivers/net/ethernet/amd/atarilance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/au1000_eth.c", "au1000_tx_timeout"], ["drivers/net/ethernet/amd/declance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/lance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/mvme147.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/ni65.c", "ni65_timeout"], ["drivers/net/ethernet/amd/nmclan_cs.c", "mace_tx_timeout"], ["drivers/net/ethernet/amd/pcnet32.c", "pcnet32_tx_timeout"], ["drivers/net/ethernet/amd/sunlance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/xgbe/xgbe-drv.c", "xgbe_tx_timeout"], ["drivers/net/ethernet/apm/xgene-v2/main.c", "xge_timeout"], ["drivers/net/ethernet/apm/xgene/xgene_enet_main.c", "xgene_enet_timeout"], ["drivers/net/ethernet/apple/macmace.c", "mace_tx_timeout"], ["drivers/net/ethernet/atheros/ag71xx.c", "ag71xx_tx_timeout"], ["drivers/net/ethernet/atheros/alx/main.c", "alx_tx_timeout"], ["drivers/net/ethernet/atheros/atl1c/atl1c_main.c", "atl1c_tx_timeout"], ["drivers/net/ethernet/atheros/atl1e/atl1e_main.c", "atl1e_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl.c", "atlx_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl1.c", "atlx_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl2.c", "atl2_tx_timeout"], ["drivers/net/ethernet/broadcom/b44.c", "b44_tx_timeout"], ["drivers/net/ethernet/broadcom/bcmsysport.c", "bcm_sysport_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2.c", "bnx2_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnxt/bnxt.c", "bnxt_tx_timeout"], ["drivers/net/ethernet/broadcom/genet/bcmgenet.c", "bcmgenet_timeout"], ["drivers/net/ethernet/broadcom/sb1250-mac.c", "sbmac_tx_timeout"], ["drivers/net/ethernet/broadcom/tg3.c", "tg3_tx_timeout"], ["drivers/net/ethernet/calxeda/xgmac.c", "xgmac_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_main.c", "liquidio_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_vf_main.c", "liquidio_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_vf_rep.c", "lio_vf_rep_tx_timeout"], ["drivers/net/ethernet/cavium/thunder/nicvf_main.c", "nicvf_tx_timeout"], ["drivers/net/ethernet/cirrus/cs89x0.c", "net_timeout"], ["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"], ["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"], ["drivers/net/ethernet/cortina/gemini.c", "gmac_tx_timeout"], ["drivers/net/ethernet/davicom/dm9000.c", "dm9000_timeout"], ["drivers/net/ethernet/dec/tulip/de2104x.c", "de_tx_timeout"], ["drivers/net/ethernet/dec/tulip/tulip_core.c", "tulip_tx_timeout"], ["drivers/net/ethernet/dec/tulip/winbond-840.c", "tx_timeout"], ["drivers/net/ethernet/dlink/dl2k.c", "rio_tx_timeout"], ["drivers/net/ethernet/dlink/sundance.c", "tx_timeout"], ["drivers/net/ethernet/emulex/benet/be_main.c", "be_tx_timeout"], ["drivers/net/ethernet/ethoc.c", "ethoc_tx_timeout"], ["drivers/net/ethernet/faraday/ftgmac100.c", "ftgmac100_tx_timeout"], ["drivers/net/ethernet/fealnx.c", "fealnx_tx_timeout"], ["drivers/net/ethernet/freescale/dpaa/dpaa_eth.c", "dpaa_tx_timeout"], ["drivers/net/ethernet/freescale/fec_main.c", "fec_timeout"], ["drivers/net/ethernet/freescale/fec_mpc52xx.c", "mpc52xx_fec_tx_timeout"], ["drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c", "fs_timeout"], ["drivers/net/ethernet/freescale/gianfar.c", "gfar_timeout"], ["drivers/net/ethernet/freescale/ucc_geth.c", "ucc_geth_timeout"], ["drivers/net/ethernet/fujitsu/fmvj18x_cs.c", "fjn_tx_timeout"], ["drivers/net/ethernet/google/gve/gve_main.c", "gve_tx_timeout"], ["drivers/net/ethernet/hisilicon/hip04_eth.c", "hip04_timeout"], ["drivers/net/ethernet/hisilicon/hix5hd2_gmac.c", "hix5hd2_net_timeout"], ["drivers/net/ethernet/hisilicon/hns/hns_enet.c", "hns_nic_net_timeout"], ["drivers/net/ethernet/hisilicon/hns3/hns3_enet.c", "hns3_nic_net_timeout"], ["drivers/net/ethernet/huawei/hinic/hinic_main.c", "hinic_tx_timeout"], ["drivers/net/ethernet/i825xx/82596.c", "i596_tx_timeout"], ["drivers/net/ethernet/i825xx/ether1.c", "ether1_timeout"], ["drivers/net/ethernet/i825xx/lib82596.c", "i596_tx_timeout"], ["drivers/net/ethernet/i825xx/sun3_82586.c", "sun3_82586_timeout"], ["drivers/net/ethernet/ibm/ehea/ehea_main.c", "ehea_tx_watchdog"], ["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"], ["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"], ["drivers/net/ethernet/ibm/ibmvnic.c", "ibmvnic_tx_timeout"], ["drivers/net/ethernet/intel/e100.c", "e100_tx_timeout"], ["drivers/net/ethernet/intel/e1000/e1000_main.c", "e1000_tx_timeout"], ["drivers/net/ethernet/intel/e1000e/netdev.c", "e1000_tx_timeout"], ["drivers/net/ethernet/intel/fm10k/fm10k_netdev.c", "fm10k_tx_timeout"], ["drivers/net/ethernet/intel/i40e/i40e_main.c", "i40e_tx_timeout"], ["drivers/net/ethernet/intel/iavf/iavf_main.c", "iavf_tx_timeout"], ["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"], ["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"], ["drivers/net/ethernet/intel/igb/igb_main.c", "igb_tx_timeout"], ["drivers/net/ethernet/intel/igbvf/netdev.c", "igbvf_tx_timeout"], ["drivers/net/ethernet/intel/ixgb/ixgb_main.c", "ixgb_tx_timeout"], ["drivers/net/ethernet/intel/ixgbe/ixgbe_debugfs.c", "adapter->netdev->netdev_ops->ndo_tx_timeout(adapter->netdev);"], ["drivers/net/ethernet/intel/ixgbe/ixgbe_main.c", "ixgbe_tx_timeout"], ["drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c", "ixgbevf_tx_timeout"], ["drivers/net/ethernet/jme.c", "jme_tx_timeout"], ["drivers/net/ethernet/korina.c", "korina_tx_timeout"], ["drivers/net/ethernet/lantiq_etop.c", "ltq_etop_tx_timeout"], ["drivers/net/ethernet/marvell/mv643xx_eth.c", "mv643xx_eth_tx_timeout"], ["drivers/net/ethernet/marvell/pxa168_eth.c", "pxa168_eth_tx_timeout"], ["drivers/net/ethernet/marvell/skge.c", "skge_tx_timeout"], ["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"], ["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"], ["drivers/net/ethernet/mediatek/mtk_eth_soc.c", "mtk_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx5/core/en_main.c", "mlx5e_tx_timeout"], ["drivers/net/ethernet/micrel/ks8842.c", "ks8842_tx_timeout"], ["drivers/net/ethernet/micrel/ksz884x.c", "netdev_tx_timeout"], ["drivers/net/ethernet/microchip/enc28j60.c", "enc28j60_tx_timeout"], ["drivers/net/ethernet/microchip/encx24j600.c", "encx24j600_tx_timeout"], ["drivers/net/ethernet/natsemi/sonic.h", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/sonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/jazzsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/macsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/natsemi.c", "ns_tx_timeout"], ["drivers/net/ethernet/natsemi/ns83820.c", "ns83820_tx_timeout"], ["drivers/net/ethernet/natsemi/xtsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/neterion/s2io.h", "s2io_tx_watchdog"], ["drivers/net/ethernet/neterion/s2io.c", "s2io_tx_watchdog"], ["drivers/net/ethernet/neterion/vxge/vxge-main.c", "vxge_tx_watchdog"], ["drivers/net/ethernet/netronome/nfp/nfp_net_common.c", "nfp_net_tx_timeout"], ["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"], ["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"], ["drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c", "pch_gbe_tx_timeout"], ["drivers/net/ethernet/packetengines/hamachi.c", "hamachi_tx_timeout"], ["drivers/net/ethernet/packetengines/yellowfin.c", "yellowfin_tx_timeout"], ["drivers/net/ethernet/pensando/ionic/ionic_lif.c", "ionic_tx_timeout"], ["drivers/net/ethernet/qlogic/netxen/netxen_nic_main.c", "netxen_tx_timeout"], ["drivers/net/ethernet/qlogic/qla3xxx.c", "ql3xxx_tx_timeout"], ["drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c", "qlcnic_tx_timeout"], ["drivers/net/ethernet/qualcomm/emac/emac.c", "emac_tx_timeout"], ["drivers/net/ethernet/qualcomm/qca_spi.c", "qcaspi_netdev_tx_timeout"], ["drivers/net/ethernet/qualcomm/qca_uart.c", "qcauart_netdev_tx_timeout"], ["drivers/net/ethernet/rdc/r6040.c", "r6040_tx_timeout"], ["drivers/net/ethernet/realtek/8139cp.c", "cp_tx_timeout"], ["drivers/net/ethernet/realtek/8139too.c", "rtl8139_tx_timeout"], ["drivers/net/ethernet/realtek/atp.c", "tx_timeout"], ["drivers/net/ethernet/realtek/r8169_main.c", "rtl8169_tx_timeout"], ["drivers/net/ethernet/renesas/ravb_main.c", "ravb_tx_timeout"], ["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"], ["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"], ["drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c", "sxgbe_tx_timeout"], ["drivers/net/ethernet/seeq/ether3.c", "ether3_timeout"], ["drivers/net/ethernet/seeq/sgiseeq.c", "timeout"], ["drivers/net/ethernet/sfc/efx.c", "efx_watchdog"], ["drivers/net/ethernet/sfc/falcon/efx.c", "ef4_watchdog"], ["drivers/net/ethernet/sgi/ioc3-eth.c", "ioc3_timeout"], ["drivers/net/ethernet/sgi/meth.c", "meth_tx_timeout"], ["drivers/net/ethernet/silan/sc92031.c", "sc92031_tx_timeout"], ["drivers/net/ethernet/sis/sis190.c", "sis190_tx_timeout"], ["drivers/net/ethernet/sis/sis900.c", "sis900_tx_timeout"], ["drivers/net/ethernet/smsc/epic100.c", "epic_tx_timeout"], ["drivers/net/ethernet/smsc/smc911x.c", "smc911x_timeout"], ["drivers/net/ethernet/smsc/smc9194.c", "smc_timeout"], ["drivers/net/ethernet/smsc/smc91c92_cs.c", "smc_tx_timeout"], ["drivers/net/ethernet/smsc/smc91x.c", "smc_timeout"], ["drivers/net/ethernet/stmicro/stmmac/stmmac_main.c", "stmmac_tx_timeout"], ["drivers/net/ethernet/sun/cassini.c", "cas_tx_timeout"], ["drivers/net/ethernet/sun/ldmvsw.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/niu.c", "niu_tx_timeout"], ["drivers/net/ethernet/sun/sunbmac.c", "bigmac_tx_timeout"], ["drivers/net/ethernet/sun/sungem.c", "gem_tx_timeout"], ["drivers/net/ethernet/sun/sunhme.c", "happy_meal_tx_timeout"], ["drivers/net/ethernet/sun/sunqe.c", "qe_tx_timeout"], ["drivers/net/ethernet/sun/sunvnet.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/sunvnet_common.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/sunvnet_common.h", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/synopsys/dwc-xlgmac-net.c", "xlgmac_tx_timeout"], ["drivers/net/ethernet/ti/cpmac.c", "cpmac_tx_timeout"], ["drivers/net/ethernet/ti/cpsw.c", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/cpsw_priv.c", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/cpsw_priv.h", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/davinci_emac.c", "emac_dev_tx_timeout"], ["drivers/net/ethernet/ti/netcp_core.c", "netcp_ndo_tx_timeout"], ["drivers/net/ethernet/ti/tlan.c", "tlan_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_net.h", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_net.c", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_wireless.c", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/spider_net.c", "spider_net_tx_timeout"], ["drivers/net/ethernet/toshiba/tc35815.c", "tc35815_tx_timeout"], ["drivers/net/ethernet/via/via-rhine.c", "rhine_tx_timeout"], ["drivers/net/ethernet/wiznet/w5100.c", "w5100_tx_timeout"], ["drivers/net/ethernet/wiznet/w5300.c", "w5300_tx_timeout"], ["drivers/net/ethernet/xilinx/xilinx_emaclite.c", "xemaclite_tx_timeout"], ["drivers/net/ethernet/xircom/xirc2ps_cs.c", "xirc_tx_timeout"], ["drivers/net/fjes/fjes_main.c", "fjes_tx_retry"], ["drivers/net/slip/slip.c", "sl_tx_timeout"], ["include/linux/usb/usbnet.h", "usbnet_tx_timeout"], ["drivers/net/usb/aqc111.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/ax88172a.c", "usbnet_tx_timeout"], ["drivers/net/usb/ax88179_178a.c", "usbnet_tx_timeout"], ["drivers/net/usb/catc.c", "catc_tx_timeout"], ["drivers/net/usb/cdc_mbim.c", "usbnet_tx_timeout"], ["drivers/net/usb/cdc_ncm.c", "usbnet_tx_timeout"], ["drivers/net/usb/dm9601.c", "usbnet_tx_timeout"], ["drivers/net/usb/hso.c", "hso_net_tx_timeout"], ["drivers/net/usb/int51x1.c", "usbnet_tx_timeout"], ["drivers/net/usb/ipheth.c", "ipheth_tx_timeout"], ["drivers/net/usb/kaweth.c", "kaweth_tx_timeout"], ["drivers/net/usb/lan78xx.c", "lan78xx_tx_timeout"], ["drivers/net/usb/mcs7830.c", "usbnet_tx_timeout"], ["drivers/net/usb/pegasus.c", "pegasus_tx_timeout"], ["drivers/net/usb/qmi_wwan.c", "usbnet_tx_timeout"], ["drivers/net/usb/r8152.c", "rtl8152_tx_timeout"], ["drivers/net/usb/rndis_host.c", "usbnet_tx_timeout"], ["drivers/net/usb/rtl8150.c", "rtl8150_tx_timeout"], ["drivers/net/usb/sierra_net.c", "usbnet_tx_timeout"], ["drivers/net/usb/smsc75xx.c", "usbnet_tx_timeout"], ["drivers/net/usb/smsc95xx.c", "usbnet_tx_timeout"], ["drivers/net/usb/sr9700.c", "usbnet_tx_timeout"], ["drivers/net/usb/sr9800.c", "usbnet_tx_timeout"], ["drivers/net/usb/usbnet.c", "usbnet_tx_timeout"], ["drivers/net/vmxnet3/vmxnet3_drv.c", "vmxnet3_tx_timeout"], ["drivers/net/wan/cosa.c", "cosa_net_timeout"], ["drivers/net/wan/farsync.c", "fst_tx_timeout"], ["drivers/net/wan/fsl_ucc_hdlc.c", "uhdlc_tx_timeout"], ["drivers/net/wan/lmc/lmc_main.c", "lmc_driver_timeout"], ["drivers/net/wan/x25_asy.c", "x25_asy_timeout"], ["drivers/net/wimax/i2400m/netdev.c", "i2400m_tx_timeout"], ["drivers/net/wireless/intel/ipw2x00/ipw2100.c", "ipw2100_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/main.c", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/orinoco_usb.c", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/orinoco.h", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_dev.c", "islpci_eth_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_eth.c", "islpci_eth_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_eth.h", "islpci_eth_tx_timeout"], ["drivers/net/wireless/marvell/mwifiex/main.c", "mwifiex_tx_timeout"], ["drivers/net/wireless/quantenna/qtnfmac/core.c", "qtnf_netdev_tx_timeout"], ["drivers/net/wireless/quantenna/qtnfmac/core.h", "qtnf_netdev_tx_timeout"], ["drivers/net/wireless/rndis_wlan.c", "usbnet_tx_timeout"], ["drivers/net/wireless/wl3501_cs.c", "wl3501_tx_timeout"], ["drivers/net/wireless/zydas/zd1201.c", "zd1201_tx_timeout"], ["drivers/s390/net/qeth_core.h", "qeth_tx_timeout"], ["drivers/s390/net/qeth_core_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"], ["drivers/staging/ks7010/ks_wlan_net.c", "ks_wlan_tx_timeout"], ["drivers/staging/qlge/qlge_main.c", "qlge_tx_timeout"], ["drivers/staging/rtl8192e/rtl8192e/rtl_core.c", "_rtl92e_tx_timeout"], ["drivers/staging/rtl8192u/r8192U_core.c", "tx_timeout"], ["drivers/staging/unisys/visornic/visornic_main.c", "visornic_xmit_timeout"], ["drivers/staging/wlan-ng/p80211netdev.c", "p80211knetdev_tx_timeout"], ["drivers/tty/n_gsm.c", "gsm_mux_net_tx_timeout"], ["drivers/tty/synclink.c", "hdlcdev_tx_timeout"], ["drivers/tty/synclink_gt.c", "hdlcdev_tx_timeout"], ["drivers/tty/synclinkmp.c", "hdlcdev_tx_timeout"], ["net/atm/lec.c", "lec_tx_timeout"], ["net/bluetooth/bnep/netdev.c", "bnep_net_timeout"] ); for my $p (@work) { my @pair = @$p; my $file = $pair[0]; my $func = $pair[1]; print STDERR $file , ": ", $func,"\n"; our @ARGV = ($file); while (<ARGV>) { if (m/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/) { print STDERR "found $1+$2 in $file\n"; } if (s/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/$1, unsigned int txqueue$2/) { print STDERR "$func found in $file\n"; } print; } } where the list of files and functions is simply from: git grep ndo_tx_timeout, with manual addition of headers in the rare cases where the function is from a header, then manually changing the few places which actually call ndo_tx_timeout. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Heiner Kallweit <hkallweit1@gmail.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Shannon Nelson <snelson@pensando.io> Reviewed-by: Martin Habets <mhabets@solarflare.com> changes from v9: fixup a forward declaration changes from v9: more leftovers from v3 change changes from v8: fix up a missing direct call to timeout rebased on net-next changes from v7: fixup leftovers from v3 change changes from v6: fix typo in rtl driver changes from v5: add missing files (allow any net device argument name) changes from v4: add a missing driver header changes from v3: change queue # to unsigned Changes from v2: added headers Changes from v1: Fix errors found by kbuild: generalize the pattern a bit, to pick up a couple of instances missed by the previous version. Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-12-12 | net: ena: Add first_interrupt field to napi struct | Sameeh Jubran | 2 | -2/+6 | |
| The first_interrupt field is accessed in ena_intr_msix_io() upon receiving an interrupt.The rx_ring and tx_ring fields of napi can be NULL when receiving interrupt for xdp queues. This patch fixes the issue by moving the field to the ena_napi struct. Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-12-12 | net: ena: Implement XDP_TX action | Sameeh Jubran | 3 | -186/+701 | |
| This commit implements the XDP_TX action in the ena driver. We allocate separate tx queues for the XDP_TX. We currently allow xdp only when there is enough queues to allocate for xdp. Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-12-12 | net: ena: implement XDP drop support | Sameeh Jubran | 2 | -11/+233 | |
| This commit implements the basic functionality of drop/pass logic in the ena driver. Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-12-10 | net: ena: fix napi handler misbehavior when the napi budget is zero |   Netanel Belgazal | 1 | -3/+7 | |
| In netpoll the napi handler could be called with budget equal to zero. Current ENA napi handler doesn't take that into consideration. The napi handler handles Rx packets in a do-while loop. Currently, the budget check happens only after decrementing the budget, therefore the napi handler, in rare cases, could run over MAX_INT packets. In addition to that, this moves all budget related variables to int calculation and stop mixing u32 to avoid ambiguity Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Netanel Belgazal <netanel@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-10-07 | net: ena: ethtool: support set_channels callback | Sameeh Jubran | 3 | -3/+35 | |
| Set channels callback enables the user to change the count of queues used by the driver using ethtool. We decided to currently support only equal number of rx and tx queues, this might change in the future. Also rename dev_up to dev_was_up in ena_update_queue_count() to make it clearer. Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-10-07 | net: ena: remove redundant print of number of queues | Sameeh Jubran | 1 | -2/+2 | |
| The number of queues can be derived using ethtool, no need to print it in ena_probe() Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-10-07 | net: ena: make ethtool -l show correct max number of queues | Sameeh Jubran | 3 | -25/+29 | |
| - Update ena_ethtool:ena_get_channels() to return adapter->max_io_queues so that ethtool -l returns the correct maximum queue number. - Change the name of ena_calc_io_queue_num() to ena_calc_max_io_queue_num() as it returns the maximum number of io queues and actual number of queues can be smaller if changed by ethtool -L which is implemented in a later commit. - Change variable name from io_queue_num to max_num_io_queues in ena_calc_max_io_queue_num() and ena_probe(). - Make all types of variables that convey the number and sizeof queues to be u32, for consistency with the API between the driver and the device. Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-10-07 | net: ena: ethtool: get_channels: use combined only | Sameeh Jubran | 1 | -8/+2 | |
| Since we use the same IRQ and NAPI to service RX and TX then we need to use a combined channel instead of rx and tx channels. Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-10-07 | net: ena: multiple queue creation related cleanups | Sameeh Jubran | 1 | -20/+11 | |
| - Rename ena_calc_queue_size() to ena_calc_io_queue_size() for clarity and consistency - Remove redundant number of io queues parameter in functions ena_enable_msix() and ena_enable_msix_and_set_admin_interrupts(), which already get adapter parameter, so use adapter->num_io_queues in the function instead. - Use the local variable ena_dev instead of ctx->ena_dev in ena_calc_io_queue_size - Fix multi row comment alignments Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-10-07 | net: ena: change num_queues to num_io_queues for clarity and consistency | Sameeh Jubran | 3 | -44/+44 | |
| Most places in the code refer to the IO queues as io_queues and not simply queues. Examples - max_io_queues_per_vf, ENA_MAX_NUM_IO_QUEUES, ena_destroy_all_io_queues() etc.. We are also adding the new max_num_io_queues field to struct ena_adapter in the following commit. The changes included in this commit are: struct ena_adapter->num_queues => struct ena_adapter->num_io_queues Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-09-27 | net: ena: clean up indentation issue |   Colin Ian King | 1 | -2/+2 | |
| There memset is indented incorrectly, remove the extraneous tabs. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-09-22 | net: ena: Select DIMLIB for ENA_ETHERNET |   Mao Wenan | 1 | -0/+1 | |
| If CONFIG_ENA_ETHERNET=y and CONFIG_DIMLIB=n, below erros can be found: drivers/net/ethernet/amazon/ena/ena_netdev.o: In function `ena_dim_work': ena_netdev.c:(.text+0x21cc): undefined reference to `net_dim_get_rx_moderation' ena_netdev.c:(.text+0x21cc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `net_dim_get_rx_moderation' drivers/net/ethernet/amazon/ena/ena_netdev.o: In function `ena_io_poll': ena_netdev.c:(.text+0x7bd4): undefined reference to `net_dim' ena_netdev.c:(.text+0x7bd4): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `net_dim' After commit 282faf61a053 ("net: ena: switch to dim algorithm for rx adaptive interrupt moderation"), it introduces dim algorithm, which configured by CONFIG_DIMLIB. So, this patch is to select DIMLIB for ENA_ETHERNET. Fixes: 282faf61a053 ("net: ena: switch to dim algorithm for rx adaptive interrupt moderation") Signed-off-by: Mao Wenan <maowenan@huawei.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> | |||||
| 2019-09-17 | Merge ra.kernel.org:/pub/scm/linux/kernel/git/netdev/net | David S. Miller | 1 | -1/+2 | |
| Pull in bug fixes from 'net' tree for the merge window. Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-09-16 | net: ena: fix incorrect update of intr_delay_resolution | Arthur Kiyanovski | 3 | -4/+19 | |
| ena_dev->intr_moder_rx/tx_interval save the intervals received from the user after dividing them by ena_dev->intr_delay_resolution. Therefore when intr_delay_resolution changes, the code needs to first mutiply intr_moder_rx/tx_interval by the previous intr_delay_resolution to get the value originally given by the user, and only then divide it by the new intr_delay_resolution. Current code does not first multiply intr_moder_rx/tx_interval by the old intr_delay_resolution. This commit fixes it. Also initialize ena_dev->intr_delay_resolution to be 1. Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-09-16 | net: ena: fix retrieval of nonadaptive interrupt moderation intervals | Arthur Kiyanovski | 1 | -2/+3 | |
| Nonadaptive interrupt moderation intervals are assigned the value set by the user in ethtool -C divided by ena_dev->intr_delay_resolution. Therefore when the user tries to get the nonadaptive interrupt moderation intervals with ethtool -c the code needs to multiply the saved value by ena_dev->intr_delay_resolution. The current code erroneously divides instead of multiplying in ethtool -c. This patch fixes this. Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-09-16 | net: ena: fix update of interrupt moderation register | Arthur Kiyanovski | 1 | -1/+4 | |
| Current implementation always updates the interrupt register with the smoothed_interval of the rx_ring. However this should be done only in case of adaptive interrupt moderation. If non-adaptive interrupt moderation is used, the non-adaptive interrupt moderation interval should be used. This commit fixes that. Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-09-16 | net: ena: remove all old adaptive rx interrupt moderation code from ena_com | Arthur Kiyanovski | 2 | -252/+0 | |
| Remove previous implementation of adaptive rx interrupt moderation from ena_com files. Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-09-16 | net: ena: remove ena_restore_ethtool_params() and relevant fields | Arthur Kiyanovski | 2 | -13/+0 | |
| Deleted unused 4 fields from struct ena_adapter and their only user ena_restore_ethtool_params(). Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-09-16 | net: ena: remove old adaptive interrupt moderation code from ena_netdev | Arthur Kiyanovski | 2 | -10/+0 | |
| 1. Out of the fields {per_napi_bytes, per_napi_packets} in struct ena_ring, only rx_ring->per_napi_packets are used to determine if napi did work for dim. This commit removes all other uses of these fields. 2. Remove ena_ring->moder_tbl_idx, which is not used by dim. 3. Remove all calls to ena_com_destroy_interrupt_moderation(), since all it did was to destroy the interrupt moderation table, which is removed as part of removing old interrupt moderation code. Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-09-16 | net: ena: remove code duplication in ena_com_update_nonadaptive_moderation_interval _*() | Arthur Kiyanovski | 1 | -14/+16 | |
| Remove code duplication in: ena_com_update_nonadaptive_moderation_interval_tx() ena_com_update_nonadaptive_moderation_interval_rx() functions. Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-09-16 | net: ena: enable the interrupt_moderation in driver_supported_features | Arthur Kiyanovski | 2 | -0/+11 | |
| Add driver_supported_features to host_host info which is a new API used to communicate to the device which features are supported by the driver. Add the interrupt_moderation bit to host_info->driver_supported_features and enable it to signal the device that this driver supports interrupt moderation properly. Reserved bits are for features implemented in the future Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-09-16 | net: ena: reimplement set/get_coalesce() | Arthur Kiyanovski | 1 | -58/+26 | |
| 1. Remove old adaptive interrupt moderation code from set/get_coalesce() 2. Add ena_update_rx_rings_intr_moderation() function for updating nonadaptive interrupt moderation intervals similarly to ena_update_tx_rings_intr_moderation(). 3. Remove checks of multiple unsupported received interrupt coalescing parameters. This makes code cleaner and cancels the need to update it every time a new coalescing parameter is invented. Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-09-16 | net: ena: switch to dim algorithm for rx adaptive interrupt moderation | Arthur Kiyanovski | 3 | -21/+41 | |
| Use the dim library for the rx adaptive interrupt moderation implementation Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-09-16 | net: ena: add intr_moder_rx_interval to struct ena_com_dev and use it | Arthur Kiyanovski | 3 | -18/+13 | |
| Add intr_moder_rx_interval to struct ena_com_dev and use it as the location where the interrupt moderation rx interval is saved, instead of the interrupt moderation table. This is done as a first step before removing the old interrupt moderation code. Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-09-16 | net: ena: don't wake up tx queue when down | Sameeh Jubran | 1 | -1/+2 | |
| There is a race condition that can occur when calling ena_down(). The ena_clean_tx_irq() - which is a part of the napi handler - function might wake up the tx queue when the queue is supposed to be down (during recovery or changing the size of the queues for example) This causes the ena_start_xmit() function to trigger and possibly try to access the destroyed queues. The race is illustrated below: Flow A: Flow B(napi handler) ena_down() netif_carrier_off() netif_tx_disable() ena_clean_tx_irq() netif_tx_wake_queue() ena_napi_disable_all() ena_destroy_all_io_queues() After these flows the tx queue is active and ena_start_xmit() accesses the destroyed queue which leads to a kernel panic. fixes: 1738cd3ed342 (net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)) Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-06-26 | Revert "net: ena: ethtool: add extra properties retrieval via get_priv_flags" |   Jakub Kicinski | 6 | -184/+11 | |
| This reverts commit 315c28d2b714 ("net: ena: ethtool: add extra properties retrieval via get_priv_flags"). As discussed at netconf and on the mailing list we can't allow for the the abuse of private flags for exposing arbitrary device labels. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-06-23 | net: ena: Fix bug where ring allocation backoff stopped too late | Sameeh Jubran | 1 | -2/+2 | |
| The current code of create_queues_with_size_backoff() allows the ring size to become as small as ENA_MIN_RING_SIZE/2. This is a bug since we don't want the queue ring to be smaller than ENA_MIN_RING_SIZE In this commit we change the loop's termination condition to look at the queue size of the next iteration instead of that of the current one, so that the minimal queue size again becomes ENA_MIN_RING_SIZE. Fixes: eece4d2ab9d2 ("net: ena: add ethtool function for changing io queue sizes") Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-06-12 | net: ena: update driver version from 2.0.3 to 2.1.0 | Sameeh Jubran | 1 | -2/+2 | |
| Update driver version to match device specification. Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-06-12 | net: ena: remove inline keyword from functions in *.c | Sameeh Jubran | 3 | -24/+24 | |
| Let the compiler decide if the function should be inline in *.c files Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-06-12 | net: ena: add ethtool function for changing io queue sizes | Sameeh Jubran | 3 | -1/+40 | |
| Implement the set_ringparam() function of the ethtool interface to enable the changing of io queue sizes. Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-06-12 | net: ena: allow queue allocation backoff when low on memory | Sameeh Jubran | 3 | -42/+127 | |
| If there is not enough memory to allocate io queues the driver will try to allocate smaller queues. The backoff algorithm is as follows: 1. Try to allocate TX and RX and if successful. 1.1. return success 2. Divide by 2 the size of the larger of RX and TX queues (or both if their size is the same). 3. If TX or RX is smaller than 256 3.1. return failure. 4. else 4.1. go back to 1. Also change the tx_queue_size, rx_queue_size field names in struct adapter to requested_tx_queue_size and requested_rx_queue_size, and use RX and TX queue 0 for actual queue sizes. Explanation: The original fields were useless as they were simply used to assign values once from them to each of the queues in the adapter in ena_probe(). They could simply be deleted. However now that we have a backoff feature, we have use for them. In case of backoff there is a difference between the requested queue sizes and the actual sizes. Therefore there is a need to save the requested queue size for future retries of queue allocation (for example if allocation failed and then ifdown + ifup was called we want to start the allocation from the original requested size of the queues). Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-06-12 | net: ena: make ethtool show correct current and max queue sizes | Sameeh Jubran | 2 | -6/+6 | |
| Currently ethtool -g shows the same size for current and max queue sizes. Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
| 2019-06-12 | net: ena: enable negotiating larger Rx ring size | Sameeh Jubran | 2 | -49/+110 | |
| Use MAX_QUEUES_EXT get feature capability to query the device. Signed-off-by: Netanel Belgazal <netanel@amazon.com> Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||||
 |
index : linux-dev | |
| Linux kernel development work - see feature branches | Jason A. Donenfeld |
| aboutsummaryrefslogtreecommitdiffstats |