| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
include/net/sock.h
310731e2f161 ("net: Fix data-races around sysctl_mem.")
e70f3c701276 ("Revert "net: set SK_MEM_QUANTUM to 4096"")
https://lore.kernel.org/all/20220711120211.7c8b7cba@canb.auug.org.au/
net/ipv4/fib_semantics.c
747c14307214 ("ip: fix dflt addr selection for connected nexthop")
d62607c3fe45 ("net: rename reference+tracking helpers")
net/tls/tls.h
include/net/tls.h
3d8c51b25a23 ("net/tls: Check for errors in tls_device_init")
587903142308 ("tls: create an internal header")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The upper 32-bit PHC register is not latched when reading the lower
32-bit PHC register. Current code leaves a small window where we may
not read correct higher order bits if the lower order bits are just about
to wrap around.
This patch fixes this by reading higher order bits twice and makes
sure that final value is correctly paired with its lower 32 bits.
Fixes: 30e96f487f64 ("bnxt_en: Do not read the PTP PHC during chip reset")
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix the missing length hint in the TX BD for the XDP transmit path. The
length hint is required on legacy chips.
Also, simplify the code by eliminating the first_buf local variable.
tx_buf contains the same value. The opaque value only needs to be set
on the first BD. Fix this also for correctness.
Fixes: a7559bc8c17c ("bnxt: support transmit and free of aggregation buffers")
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the livepatch query fw_target BNXT_FW_SRT_PATCH is
applicable for P5 chips only.
Fixes: 3c4153394e2c ("bnxt_en: implement firmware live patching")
Reviewed-by: Saravanan Vajravel <saravanan.vajravel@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
bnxt_reinit_after_abort() is called during ifup when a previous
FW reset sequence has aborted or a previous ifup has failed after
detecting FW reset. In all cases, it is safe to assume that a
previous FW reset has completed and the driver may not have fully
reinitialized.
Prior to this patch, it is assumed that the
FUNC_DRV_IF_CHANGE_RESP_FLAGS_HOT_FW_RESET_DONE flag will always be
set by the firmware in bnxt_hwrm_if_change(). This may not be true if
the driver has already attempted to register with the firmware. The
firmware may not set the RESET_DONE flag again after the driver has
registered, assuming that the driver has seen the flag already.
Fix it to always go through the FW reset initialization path if
the BNXT_STATE_FW_RESET_DET flag is set. This flag is always set
by the driver after successfully going through bnxt_reinit_after_abort().
Fixes: 6882c36cf82e ("bnxt_en: attempt to reinitialize after aborted reset")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If bnxt_sriov_enable() fails after some resources have been reserved
for the VFs, the current code is not unwinding properly and the
reserved resources become unavailable afterwards. Fix it by
properly unwinding with a call to bnxt_hwrm_func_qcaps() to
reset all maximum resources.
Also, add the missing bnxt_ulp_sriov_cfg() call to let the RDMA
driver know to abort.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use bitmap_zalloc()/bitmap_free() instead of hand-writing them.
It is less verbose and it improves the semantic.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/d508f3adf7e2804f4d3793271b82b196a2ccb940.1657052562.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Most drivers use "skb_transport_offset(skb) + tcp_hdrlen(skb)"
to compute headers length for a TCP packet, but others
use more convoluted (but equivalent) ways.
Add skb_tcp_all_headers() and skb_inner_tcp_all_headers()
helpers to harmonize this a bit.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the repeated word 'and' from comments
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Link: https://lore.kernel.org/r/20220622144526.20659-1-jiangjian@cdjrlc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The commit a14857c27a50 ("rtnetlink: verify rate parameters for calls to
ndo_set_vf_rate") has been merged to master, so we can to remove the
now-duplicate checks in drivers.
Signed-off-by: Bin Chen <bin.chen@corigine.com>
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220609084717.155154-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
GCC array bounds checking complains that ulp_id is validated
only against upper bound. Make it unsigned.
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20220520061955.2312968-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Instead of always returning -ENOPKG, decode the firmware error
code further when the HWRM_NVM_INSTALL_UPDATE firmware call fails.
Return a more suitable error code to userspace and log an error
in dmesg.
This is version 2 of the earlier patch that was reverted:
02acd399533e ("bnxt_en: parse result field when NVRAM package install fails")
In this new version, if the call is made through devlink instead of
ethtool, we'll also set the error message in extack.
Link: https://lore.kernel.org/netdev/20220307141358.4d52462e@kicinski-fedora-pc1c0hjn.dhcp.thefacebook.com/
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add driver support to enable timestamping on all RX packets
that are received by the NIC. This capability can be requested
by the applications using SIOCSHWTSTAMP ioctl with filter type
HWTSTAMP_FILTER_ALL.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For correctness, we need to configure the packet filters for timestamping
during bnxt_open. This way they are always configured after firmware
reset or chip reset. We should not assume that the filters will always
be retained across resets.
This patch modifies the ioctl handler and always configures the PTP
filters in the bnxt_open() path.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The main changes are timestamp support for all RX packets and new PCIe
statistics.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tools/testing/selftests/net/forwarding/Makefile
f62c5acc800e ("selftests/net/forwarding: add missing tests to Makefile")
50fe062c806e ("selftests: forwarding: new test, verify host mdb entries")
https://lore.kernel.org/all/20220502111539.0b7e4621@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In bnxt_poll_p5(), we first check cpr->has_more_work. If it is true,
we are in NAPI polling mode and we will call __bnxt_poll_cqs() to
continue polling. It is possible to exhanust the budget again when
__bnxt_poll_cqs() returns.
We then enter the main while loop to check for new entries in the NQ.
If we had previously exhausted the NAPI budget, we may call
__bnxt_poll_work() to process an RX entry with zero budget. This will
cause packets to be dropped unnecessarily, thinking that we are in the
netpoll path. Fix it by breaking out of the while loop if we need
to process an RX NQ entry with no budget left. We will then exit
NAPI and stay in polling mode.
Fixes: 389a877a3b20 ("bnxt_en: Process the NQ under NAPI continuous polling.")
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
bnxt_ptp_init() calls bnxt_ptp_init_rtc() which will acquire the ptp_lock
spinlock. The spinlock is not initialized until later. Move the
bnxt_ptp_init_rtc() call after the spinlock is initialized.
Fixes: 24ac1ecd5240 ("bnxt_en: Add driver support to use Real Time Counter for PTP")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Saravanan Vajravel <saravanan.vajravel@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
bnxt_open() can fail in this code path, especially on a VF when
it fails to reserve default rings:
bnxt_open()
__bnxt_open_nic()
bnxt_clear_int_mode()
bnxt_init_dflt_ring_mode()
RX rings would be set to 0 when we hit this error path.
It is possible for a subsequent bnxt_open() call to potentially succeed
with a code path like this:
bnxt_open()
bnxt_hwrm_if_change()
bnxt_fw_init_one()
bnxt_fw_init_one_p3()
bnxt_set_dflt_rfs()
bnxt_rfs_capable()
bnxt_hwrm_reserve_rings()
On older chips, RFS is capable if we can reserve the number of vnics that
is equal to RX rings + 1. But since RX rings is still set to 0 in this
code path, we may mistakenly think that RFS is supported for 0 RX rings.
Later, when the default RX rings are reserved and we try to enable
RFS, it would fail and cause bnxt_open() to fail unnecessarily.
We fix this in 2 places. bnxt_rfs_capable() will always return false if
RX rings is not yet set. bnxt_init_dflt_ring_mode() will call
bnxt_set_dflt_rfs() which will always clear the RFS flags if RFS is not
supported.
Fixes: 20d7d1c5c9b1 ("bnxt_en: reliably allocate IRQ table on reset to avoid crash")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Allow aggregation buffers to be in place in the receive path and
allow XDP programs to be attached when using a larger than 4k MTU.
v3: Add a check to sure XDP program supports multipage packets.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the following features:
- Support for XDP_TX and XDP_DROP action when using xdp_buff
with frags
- Support for freeing all frags attached to an xdp_buff
- Cleanup of TX ring buffers after transmits complete
- Slight change in definition of bnxt_sw_tx_bd since nr_frags
and RX producer may both need to be used
- Clear out skb_shared_info at the end of the buffer
v2: Fix uninitialized variable warning in bnxt_xdp_buff_frags_free().
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since we have an xdp_buff with frags there needs to be a way to
convert that into a valid sk_buff in the event that XDP_PASS is
the resulting operation. This adds a new rx_skb_func when the
netdev has an MTU that prevents the packets from sitting in a
single page.
This also make sure that GRO/LRO stay disabled even when using
the aggregation ring for large buffers.
v3: Use BNXT_PAGE_MODE_BUF_SIZE for build_skb
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we are using aggregation rings with XDP enabled, allocate page
buffers for the aggregation rings from the page_pool.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Modify ring header data split and jumbo parameters to account
for the fact that the design for XDP multibuffer puts close to
the first 4k of data in a page and the remaining portions of
the packet go in the aggregation ring.
v3: Simplified code around initial buffer size calculation
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set the pfmemaloc flag in the xdp buff so that this can be
copied to the skb if needed for an XDP_PASS action.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a new function that will read pages from the
aggregation ring and create an xdp_buff with frags based on
the entries in the aggregation ring.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clarify that this is reading buffers from the aggregation ring.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rather than operating on an sk_buff, add frags from the aggregation
ring into the frags of an skb_shared_info. This will allow the
caller to use either an sk_buff or xdp_buff.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This will be used to determine if bnxt_rx_xdp should be called
rather than calling it every time.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move initialization of xdp_buff outside of bnxt_rx_xdp to prepare
for allowing bnxt_rx_xdp to operate on multibuffer xdp_buffs.
v2: Fix uninitalized variables warning in bnxt_xdp.c.
v3: Add new define BNXT_PAGE_MODE_BUF_SIZE
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add checks in the XDP redirect callback to prevent XDP from running when
the TX ring is undergoing shutdown.
Also remove redundant checks in the XDP redirect callback to validate the
txr and the flag that indicates the ring supports XDP. The modulo
arithmetic on 'tx_nr_rings_xdp' already guarantees the derived TX
ring is an XDP ring. txr is also guaranteed to be valid after checking
BNXT_STATE_OPEN and within RCU grace period.
Fixes: f18c2b77b2e4 ("bnxt_en: optimized XDP_REDIRECT support")
Reviewed-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Insufficient space was being reserved in the page used for packet
reception, so the interface MTU could be set too large to still have
room for the contents of the packet when doing XDP redirect. This
resulted in the following message when redirecting a packet between
3520 and 3822 bytes with an MTU of 3822:
[311815.561880] XDP_WARN: xdp_update_frame_from_buff(line:200): Driver BUG: missing reserved tailroom
Fixes: f18c2b77b2e4 ("bnxt_en: optimized XDP_REDIRECT support")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If there are more CPUs than the number of TX XDP rings, multiple XDP
redirects can select the same TX ring based on the CPU on which
XDP redirect is called. Add locking when needed and use static
key to decide whether to take the lock.
Fixes: f18c2b77b2e4 ("bnxt_en: optimized XDP_REDIRECT support")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Broadcom bnxt_ptp driver does not compile with GCC 11.2.2 when
CONFIG_WERROR is enabled. The following error is generated:
drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c: In function ‘bnxt_ptp_enable’:
drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c:400:43: error: array
subscript 255 is above array bounds of ‘struct pps_pin[4]’
[-Werror=array-bounds]
400 | ptp->pps_info.pins[pin_id].event = BNXT_PPS_EVENT_EXTERNAL;
| ~~~~~~~~~~~~~~~~~~^~~~~~~~
In file included from drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.c:20:
drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.h:75:24: note: while
referencing ‘pins’
75 | struct pps_pin pins[BNXT_MAX_TSIO_PINS];
| ^~~~
cc1: all warnings being treated as errors
This is due to the function ptp_find_pin() returning a pin ID of -1 when
a valid pin is not found and this error never being checked.
Change the TSIO_PIN_VALID() function to also check that a pin ID is not
negative and use this macro in bnxt_ptp_enable() to check the result of
the calls to ptp_find_pin() to return an error early for invalid pins.
This fixes the compilation error.
Cc: <stable@vger.kernel.org>
Fixes: 9e518f25802c ("bnxt_en: 1PPS functions to configure TSIO pins")
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20220328062708.207079-1-damien.lemoal@opensource.wdc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make the devlink core hold the instance lock during eswitch_mode
callbacks. Cheat in case of mlx5 (see the cover letter).
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In prep for .eswitch_mode_set being called with the devlink instance
lock held use that lock explicitly instead of creating a local mutex
just for the sriov reconfig.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before adding yet another possibly contended atomic_long_t,
it is time to add per-cpu storage for existing ones:
dev->tx_dropped, dev->rx_dropped, and dev->rx_nohandler
Because many devices do not have to increment such counters,
allocate the per-cpu storage on demand, so that dev_get_stats()
does not have to spend considerable time folding zero counters.
Note that some drivers have abused these counters which
were supposed to be only used by core networking stack.
v4: should use per_cpu_ptr() in dev_get_stats() (Jakub)
v3: added a READ_ONCE() in netdev_core_stats_alloc() (Paolo)
v2: add a missing include (reported by kernel test robot <lkp@intel.com>)
Change in netdev_core_stats_alloc() (Jakub)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: jeffreyji <jeffreyji@google.com>
Reviewed-by: Brian Vazquez <brianvv@google.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20220311051420.2608812-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts:
commit 02acd399533e ("bnxt_en: parse result field when NVRAM package install fails")
commit 22f5dba5065d ("bnxt_en: add an nvm test for hw diagnose")
commit bafed3f231f7 ("bnxt_en: implement hw health reporter")
These patches are still under discussion / I don't think they
are right, and since the authors don't reply promptly let me
lessen my load of "things I need to resolve before next release"
and revert them.
Acked-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20220308173659.304915-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add an NVM test function for devlink hw reporter.
In this function an NVM VPD area is read followed by
a write. Test result is cached and if it is successful then
the next test can be conducted only after HW_RETEST_MIN_TIME to
avoid frequent writes to the NVM.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reporter will report NVM errors which are non-fatal.
When we receive these NVM error events, we'll report it
through this new hw health reporter.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Health reporter state should be maintained over resets. Previously
reporters were destroyed if the device capabilities changed, but
since none of the reporters depend on capabilities anymore, this
logic should be removed.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the flow control settings have been changed, a subsequent FW reset
may cause the ethernet link to toggle unnecessarily. This link toggle
will increase the down time by a few seconds.
The problem is caused by bnxt_update_phy_setting() detecting a false
mismatch in the flow control settings between the stored software
settings and the current FW settings after the FW reset. This mismatch
is caused by the AUTONEG bit added to link_info->req_flow_ctrl in an
inconsistent way in bnxt_set_pauseparam() in autoneg mode. The AUTONEG
bit should not be added to link_info->req_flow_ctrl.
Reviewed-by: Colin Winegarden <colin.winegarden@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some cards are configured to never support link pause or PFC. Discover
these cards and properly report no pause support to ethtool. Disable
PFC settings from DCBNL if PFC is unsupported.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This will force link state to always be logged for initial NIC open.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of always returning -ENOPKG, decode the firmware error
code further when the HWRM_NVM_INSTALL_UPDATE firmware call fails.
Return a more suitable error code to userspace and log an error
in dmesg.
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FW returns error code "NVM_INSTALL_UPDATE_CMD_ERR_CODE_ANTI_ROLLBACK"
in the response to indicate that HWRM_NVM_INSTALL_UPDATE command has
failed due to Anti-rollback feature. Parse the error and return an
appropriate error code to the user.
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is in anticipation of handling more "cmd_err" from FW in the next
patch.
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tools/testing/selftests/net/mptcp/mptcp_join.sh
34aa6e3bccd8 ("selftests: mptcp: add ip mptcp wrappers")
857898eb4b28 ("selftests: mptcp: add missing join check")
6ef84b1517e0 ("selftests: mptcp: more robust signal race test")
https://lore.kernel.org/all/20220221131842.468893-1-broonie@kernel.org/
drivers/net/ethernet/mellanox/mlx5/core/en/tc/act/act.h
drivers/net/ethernet/mellanox/mlx5/core/en/tc/act/ct.c
fb7e76ea3f3b6 ("net/mlx5e: TC, Skip redundant ct clear actions")
c63741b426e11 ("net/mlx5e: Fix MPLSoUDP encap to use MPLS action information")
09bf97923224f ("net/mlx5e: TC, Move pedit_headers_action to parse_attr")
84ba8062e383 ("net/mlx5e: Test CT and SAMPLE on flow attr")
efe6f961cd2e ("net/mlx5e: CT, Don't set flow flag CT for ct clear flow")
3b49a7edec1d ("net/mlx5e: TC, Reject rules with multiple CT actions")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
To install a livepatch, first flash the package to NVM, and then
activate the patch through the "HWRM_FW_LIVEPATCH" fw command.
To uninstall a patch from NVM, flash the removal package and then
activate it through the "HWRM_FW_LIVEPATCH" fw command.
The "HWRM_FW_LIVEPATCH" fw command has to consider following scenarios:
1. no patch in NVM and no patch active. Do nothing.
2. patch in NVM, but not active. Activate the patch currently in NVM.
3. patch is not in NVM, but active. Deactivate the patch.
4. patch in NVM and the patch active. Do nothing.
Fix the code to handle these scenarios during devlink "fw_activate".
To install and activate a live patch:
devlink dev flash pci/0000:c1:00.0 file thor_patch.pkg
devlink -f dev reload pci/0000:c1:00.0 action fw_activate limit no_reset
To remove and deactivate a live patch:
devlink dev flash pci/0000:c1:00.0 file thor_patch_rem.pkg
devlink -f dev reload pci/0000:c1:00.0 action fw_activate limit no_reset
Fixes: 3c4153394e2c ("bnxt_en: implement firmware live patching")
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When polling for the firmware message response, we first poll for the
response message header. Once the valid length is detected in the
header, we poll for the valid bit at the end of the message which
signals DMA completion. Normally, this poll time for DMA completion
is extremely short (0 to a few usec). But on some devices under some
rare conditions, it can be up to about 20 msec.
Increase this delay to 50 msec and use udelay() for the first 10 usec
for the common case, and usleep_range() beyond that.
Also, change the error message to include the above delay time when
printing the timeout value.
Fixes: 3c8c20db769c ("bnxt_en: move HWRM API implementation into separate file")
Reviewed-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Jakub Kicinski
Pavan Chebbi
Michael Chan
Vikas Gupta
Kashyap Desai
Christophe JAILLET
Eric Dumazet
Jiang Jian
Bin Chen
Kalesh AP
Somnath Kotur
Andy Gospodarek
Ray Jui
Damien Le Moal
Edwin Peer