| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
GEM version in ZynqMP and most versions greater than r1p07 supports
TX and RX BD prefetch. The number of BDs that can be prefetched is a
HW configurable parameter. For ZynqMP, this parameter is 4.
When GEM DMA is accessing the last BD in the ring, even before the
BD is processed and the WRAP bit is noticed, it will have prefetched
BDs outside the BD ring. These will not be processed but it is
necessary to have accessible memory after the last BD. Especially
in cases where SMMU is used, memory locations immediately after the
last BD may not have translation tables triggering HRESP errors. Hence
always allocate extra BDs to accommodate for prefetch.
The value of tx/rx bd prefetch for any given SoC version is:
2 ^ (corresponding field in design config 10 register).
(value of this field >= 1)
Added a capability flag so that older IP versions that do not have
DCFG10 or this prefetch capability are not affected.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Handle HRESP error by doing a SW reset of RX and TX and
re-initializing the descriptors, RX and TX queue pointers.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the phylib now being aware of the "reset-gpios" PHY node property,
there should be no need to frob the PHY reset in this driver anymore...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch allows filtering received packets to different
hardware queues (aka ntuple).
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added statistics per queue:
- qX_rx_packets
- qX_rx_bytes
- qX_rx_dropped
- qX_tx_packets
- qX_tx_bytes
- qX_tx_dropped
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To be able for packet reception on different RX queues some
configuration has to be performed. This patch checks how many
hardware queue does GEM support and initializes them.
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is based on original Harini's patch and Andrei's patch,
implemented in a separate file to ease the review/maintanance
and integration with other platforms.
This driver supports GEM-GXL:
- Register ptp clock framework
- Initialize PTP related registers
- HW time stamp on the PTP Ethernet packets are received using the
SO_TIMESTAMPING API. Time stamps are obtained from the dma buffer
descriptors
- add macb_ptp to compilation chain
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for PTP timestamps in
DMA buffer descriptors. It checks capability at runtime
and uses appropriate buffer descriptor.
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case the MACB is directly connected to a
non-mdio PHY/device, it should be possible to provide
a fixed link configuration in the DT.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of using a private copy of struct net_device_stats in struct
macb, use stats from struct net_device.
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/ethernet/cadence/macb.h:862:33: sparse: expected ; at end of declaration
drivers/net/ethernet/cadence/macb.h:862:33: sparse: Expected } at end of struct-union-enum-specifier
drivers/net/ethernet/cadence/macb.h:862:33: sparse: got phy_interface
drivers/net/ethernet/cadence/macb.h:877:1: sparse: Expected ; at the end of type declaration
drivers/net/ethernet/cadence/macb.h:877:1: sparse: got }
In file included from drivers/net/ethernet/cadence/macb_pci.c:29:0:
drivers/net/ethernet/cadence/macb.h:862:2: error: unknown type name 'phy_interface_t'
phy_interface_t phy_interface;
^~~~~~~~~~~~~~~
Add linux/phy.h to macb.h
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All merge conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for 32 bit GEM in
64 bit system. It checks capability at runtime
and uses appropriate buffer descriptor.
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch does the following:
- MACB/GEM-PTP interface
- registers and bitfields for TSU
- capability flags to enable PTP per platform basis
Signed-off-by: Andrei Pistirica <andrei.pistirica@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New Cadence GEM hardware support Large Segment Offload (LSO):
TCP segmentation offload (TSO) as well as UDP fragmentation
offload (UFO). Support for those features was added to the driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The macb driver hardcoded the tx/rx ring sizes. This made it
impossible to change the sizes at run time.
Add tx_ring_size, and rx_ring_size variables to macb object, which
are initilized with default vales during macb_init. Change all
references to RX_RING_SIZE and TX_RING_SIZE to their respective
replacements.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of the platforms like zynqmp ultrascale+ has a
separate clock gate for the rx clock. Add an optional
rx_clk so that the clock can be enabled.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for 64 bit addressing and BDs.
-> Enable 64 bit addressing in DMACFG register.
-> Set DMA mask when design config register shows support for 64 bit addr.
-> Add new BD words for higher address when 64 bit DMA support is present.
-> Add and update TBQPH and RBQPH for MSB of BD pointers.
-> Change extraction and updation of buffer addresses to use
64 bit address.
-> In gem_rx extract address in one place insted of two and use a
separate flag for RXUSED.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
USRIO and JUMBO CAPS have the same mask.
Fix the same.
Fixes: ce721a702197 ("net: ethernet: cadence-macb: Add disabled usrio caps")
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On AT91 SoCs, the User Register (USRIO) exposes a switch to configure the
"Reduced" or "Traditional" version of the Media Independent Interface
(RMII vs. MII or RGMII vs. GMII).
As on the older EMAC version, on GMAC, this switch is set by default to the
non-reduced type of interface, so use the existing capability and extend it to
GMII as well. We then keep the current logic in the macb_init() function.
The capabilities of sama5d2, sama5d4 and sama5d3 GEM interface are updated in
the macb_config structure to be able to properly enable them with a traditional
interface (GMII or MII).
Reported-by: Romain HENRIET <romain.henriet@l-acoustics.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tested on Acqua A5 SoM (http://www.acmesystems.it/acqua).
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some platforms, the macb integration does not use the USRIO
register to configure the (R)MII port and clocks.
When the register is not implemented and the MACB error signal
is connected to the bus error, reading or writing to the USRIO
register can trigger some Imprecise External Aborts on ARM platforms.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With device tree it is no more possible to reset the PHY at board
level. Furthermore, doing in the driver allow to power down the PHY when
the network interface is no more used.
This reset can't be done at the PHY driver level. The PHY must be able to
answer the to the mii bus scan to let the kernel creating a PHY device.
The patch introduces a new optional property "phy-reset-gpios" inspired
from the one use for the FEC.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for the sgmii phy interface.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If an architecture defines readl/writel using CPP macros, we
get the following kinds of build failure:
> > > drivers/net/ethernet/cadence/macb.c:164:1: error: macro "writel"
> > > passed 3 arguments, but takes just 2
> macb_or_gem_writel(bp, SA1B, bottom);
> ^
Rename the methods so that this doesn't happen.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the following warnings:
drivers/net/ethernet/cadence/macb.c: In function ‘macb_handle_link_change’:
drivers/net/ethernet/cadence/macb.c:266: warning: comparison between signed and unsigned
drivers/net/ethernet/cadence/macb.c:267: warning: comparison between signed and unsigned
drivers/net/ethernet/cadence/macb.c:291: warning: comparison between signed and unsigned
drivers/net/ethernet/cadence/macb.c: In function ‘gem_update_stats’:
drivers/net/ethernet/cadence/macb.c:1908: warning: comparison between signed and unsigned
drivers/net/ethernet/cadence/macb.c: In function ‘gem_get_ethtool_strings’:
drivers/net/ethernet/cadence/macb.c:1988: warning: comparison between signed and unsigned
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit a50dad355a53 (net: macb: Add big endian CPU support) converted I/O
accessors to readl_relaxed() and writel_relaxed() and consequentially broke
MACB driver on AVR32 platforms such as ATNGW100.
This patch improves I/O access by checking endiannes first and use the
corresponding methods.
Fixes: a50dad355a53 (net: macb: Add big endian CPU support)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
JUMBO and NO_GIGABIT_HALF have the same capability masks.
Change one of them.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/cadence/macb.c
drivers/net/phy/phy.c
include/linux/skbuff.h
net/ipv4/tcp.c
net/switchdev/switchdev.c
Switchdev was a case of RTNH_H_{EXTERNAL --> OFFLOAD}
renaming overlapping with net-next changes of various
sorts.
phy.c was a case of two changes, one adding a local
variable to a function whilst the second was removing
one.
tcp.c overlapped a deadlock fix with the addition of new tcp_info
statistic values.
macb.c involved the addition of two zyncq device entries.
skbuff.h involved adding back ipv4_daddr to nf_bridge_info
whilst net-next changes put two other existing members of
that struct into a union.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the Zynq TRM, gigabit half duplex is not supported. Add a
new cap and compatible string so Zynq can avoid advertising that mode.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable jumbo frame support for Zynq Ultrascale+ MPSoC.
Update the NWCFG register and descriptor length masks accordingly.
Jumbo max length register should be set according to support in SoC; it is
set to 10240 for Zynq Ultrascale+ MPSoC.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Reviewed-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As we need to check peripheral version from the hardware during probe, I
introduce a little helper to unify these tests. It would prevent to
de-synchronize the test like previously observed.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
User i/o register EMAC_USRIO or GMAC_UR can be found on both macb and gem
flavors of the peripheral. By using the proper accessor, we can add it to the
register dump feature of ethtool.
Increment the version of this API so it can be noticed from user space.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As accessing the peripheral registers need the clocks to be set, we have to
enable them as soon as possible. Their configuration depend on the type of
device used and determined by the DT compatible string. That lead to add
another initialization function in the DT configuration structure.
As the device private structure length depend on an information read in the
registers, we have to store the clock pointers in temporary variables before
feeding the structure fields.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When merging at91_ether and macb driver during 421d9df0628b (net/macb: merge
at91_ether driver into macb driver) the probe function has been split. The code
dealing with initialization of queues is now moved in macb_init() which needs
information computed in the parent macb_probe() function.
So, add the queue_mask information to the private structure and use it when
needed in macb_init().
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/cadence/macb.c
Overlapping changes in macb driver, mostly fixes and cleanups
in 'net' overlapping with the integration of at91_ether into
macb in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
macb and at91_ether drivers can be compiled as modules, but the at91_ether
driver use some functions and variables defined in the macb one, thus
creating a dependency on the macb driver.
Since these drivers are sharing the same logic we can easily merge
at91_ether into macb.
In order to factorize common probing logic we've added an ->init() function
to struct macb_config (the structure associated with the compatible
string), and moved macb specific init code from macb_probe to macb_init.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With multi platform support those sections could lead to unexpected
behavior if both ARCH_AT91 and another ARM SoC using the MACB IP are
selected.
Add two new capabilities to encode the default MII mode and the presence
of a CLKEN bit in USRIO register.
Then define the appropriate config for IPs embedded in at91 SoCs.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The latest spec "I-IPA01-0266-USR Rev 10" limit the MID field length to 12 bit
value. For previous versions it is 16 bit value.
This change will not break the backward compatibility as the latest ID value is
7 and with in the 12 bit value limit.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add *_SIZE macros for the bits ENDIA_DESC and
ENDIA_PKT
Signed-off-by: Arun Chandran <achandran@mvista.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch converts all __raw_readl and __raw_writel function calls
to their corresponding readl_relaxed and writel_relaxed variants.
It also tells the driver to set ahb_endian_swp_mgmt_en bit in dma_cfg
when the CPU is configured in big endian mode.
Signed-off-by: Arun Chandran <achandran@mvista.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change comments to not exceed 80 characters per line.
Update block comments in macb.h to start on the line after /*.
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently `ethtool -S` simply returns "no stats available". It
would be more useful to see what the various ethtool statistics
registers' values are. This change implements get_ethtool_stats,
get_strings, and get_sset_count functions to accomplish this.
Read all GEM statistics registers and sum them into
macb.ethtool_stats. Add the necessary infrastructure to make this
accessible via `ethtool -S`.
Update gem_update_stats to utilize ethtool_stats.
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change is to help improve at-a-glace knowledge of the purpose of the
various Cadence MACB/GEM registers. Comments are more helpful for human
readability than short acronyms.
Describe various #define varibles Cadence MACB/GEM registers as documented
in Xilinix's "Zynq-7000 All Programmable SoC TechnicalReference Manual, v1.9.1
(UG-585)"
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gem devices designed with multiqueue CANNOT work without this patch.
When probing a gem device, the driver must first prepare and enable the
peripheral clock before accessing I/O registers. The second step is to read the
MID register to find whether the device is a gem or an old macb IP.
For gem devices, it reads the Design Configuration Register 6 (DCFG6) to
compute to total number of queues, whereas macb devices always have a single
queue.
Only then it can call alloc_etherdev_mq() with the correct number of queues.
This is the reason why the order of some initializations has been changed in
macb_probe().
Eventually, the dedicated IRQ and TX ring buffer descriptors are initialized
for each queue.
For backward compatibility reasons, queue0 uses the legacy registers ISR, IER,
IDR, IMR, TBQP and RBQP. On the other hand, the other queues use new registers
ISR[1..7], IER[1..7], IDR[1..7], IMR[1..7], TBQP[1..7] and RBQP[1..7].
Except this hardware detail there is no real difference between queue0 and the
others. The driver hides that thanks to the struct macb_queue.
This structure allows us to share a common set of functions for all the queues.
Besides when a TX error occurs, the gem MUST be halted before writing any of
the TBQP registers to reset the relevant queue. An immediate side effect is
that the other queues too aren't processed anymore by the gem.
So macb_tx_error_task() calls netif_tx_stop_all_queues() to notify the Linux
network engine that all transmissions are stopped.
Also macb_tx_error_task() now calls spin_lock_irqsave() to prevent the
interrupt handlers of the other queues from running as each of them may wake
its associated queue up (please refer to macb_tx_interrupt()).
Finally, as all queues have previously been stopped, they should be restarted
calling netif_tx_start_all_queues() and setting the TSTART bit into the Network
Control Register. Before this patch, when dealing with a single queue, the
driver used to defer the reset of the faulting queue and the write of the
TSTART bit until the next call of macb_start_xmit().
As explained before, this bit is now set by macb_tx_error_task() too. That's
why the faulting queue MUST be reset by setting the TX_USED bit in its first
buffer descriptor before writing the TSTART bit.
Queue 0 always exits and is the lowest priority when other queues are available.
The higher the index of the queue is, the higher its priority is.
When transmitting frames, the TX queue is selected by the skb->queue_mapping
value. So queue discipline can be used to define the queue priority policy.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When RX checksum offload is enabled at GEM level (bit 24 set in the Network
Control Register), frames with invalid IP, TCP or UDP checksums are
discarted even if promiscuous mode is enabled (bit 4 set in the Network Control
Register).
This was verified with a simple userspace program, which corrupts UDP checksum
using libnetfilter_queue.
Then both IFF_PROMISC bit must be clear in dev->flags and NETIF_F_RXCSUM bit
must be set in dev->features to enable RX checksum offload at GEM level. This
way tcpdump is still able to capture corrupted frames.
Also skb->ip_summed is set to CHECKSUM_UNNECESSARY only when both TCP/IP or
UDP/IP checksums were verified by the GEM. Indeed the GEM may verify only IP
checksum but not the one for ICMP (or other protocol than TCP or UDP).
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The scatter-gather feature will allow to enable the Generic Segmentation Offload.
Generic Segmentation Offload can be enabled/disabled using ethtool -K DEVNAME gso on|off.
e.g:
ethtool -K eth0 gso off
When enabled, the driver may be provided with socket buffers splitted into many fragments.
These fragments need to be queued into the TX ring in reverse order, starting from to the
last one down to the first one, to avoid a race condition with the MAC.
Especially the 'TX_USED' bit in word 1 of the transmit buffer descriptor of the
first fragment should be cleared at the very final step of the queueing algorithm.
This will tell the hardware that fragments are ready to be sent.
Also since the MAC only update the status word of the first buffer descriptor of the
ethernet frame, the queueing algorithm can no longer expect a 'TX_USED' bit to be set by
the MAC into the buffer descriptor following the one for last fragment of the skb.
This is why the driver sets the 'TX_USED' bit before queueing any fragment, so the end of
queue position is well defined for the MAC.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This addition will also allow to configure DMA burst length.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Harini Katakam
Sergei Shtylyov
Rafal Ozieblo
Michael Grzeschik
Tobias Klauser
Russell King
David S. Miller
Andrei.Pistirica@microchip.com
Zach Brown
shubhrajyoti.datta@xilinx.com
Philippe Reynes
Nicolas Ferre
Sergio Prado
Neil Armstrong
Gregory CLEMENT
Punnaiah Choudary Kalluri
Andy Shevchenko
Nathan Sullivan
Cyrille Pitchen
Boris BREZILLON
Arun Chandran
Xander Huff