aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/freescale/dpaa/dpaa_eth.c (follow)
AgeCommit message (Collapse)AuthorFilesLines
2020-03-08dpaa_eth: Use random MAC address when none is givenMadalin Bucur1-2/+14
If there is no valid MAC address in the device tree, use a random MAC address. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-06dpaa_eth: FMan erratum A050385 workaroundMadalin Bucur1-3/+107
Align buffers, data start, SG fragment length to avoid DMA splits. These changes prevent the A050385 erratum to manifest itself: FMAN DMA read or writes under heavy traffic load may cause FMAN internal resource leak; thus stopping further packet processing. The FMAN internal queue can overflow when FMAN splits single read or write transactions into multiple smaller transactions such that more than 17 AXI transactions are in flight from FMAN to interconnect. When the FMAN internal queue overflows, it can stall further packet processing. The issue can occur with any one of the following three conditions: 1. FMAN AXI transaction crosses 4K address boundary (Errata A010022) 2. FMAN DMA address for an AXI transaction is not 16 byte aligned, i.e. the last 4 bits of an address are non-zero 3. Scatter Gather (SG) frames have more than one SG buffer in the SG list and any one of the buffers, except the last buffer in the SG list has data size that is not a multiple of 16 bytes, i.e., other than 16, 32, 48, 64, etc. With any one of the above three conditions present, there is likelihood of stalled FMAN packet processing, especially under stress with multiple ports injecting line-rate traffic. To avoid situations that stall FMAN packet processing, all of the above three conditions must be avoided; therefore, configure the system with the following rules: 1. Frame buffers must not span a 4KB address boundary, unless the frame start address is 256 byte aligned 2. All FMAN DMA start addresses (for example, BMAN buffer address, FD[address] + FD[offset]) are 16B aligned 3. SG table and buffer addresses are 16B aligned and the size of SG buffers are multiple of 16 bytes, except for the last SG buffer that can be of any size. Additional workaround notes: - Address alignment of 64 bytes is recommended for maximally efficient system bus transactions (although 16 byte alignment is sufficient to avoid the stall condition) - To support frame sizes that are larger than 4K bytes, there are two options: 1. Large single buffer frames that span a 4KB page boundary can be converted into SG frames to avoid transaction splits at the 4KB boundary, 2. Align the large single buffer to 256B address boundaries, ensure that the frame address plus offset is 256B aligned. - If software generated SG frames have buffers that are unaligned and with random non-multiple of 16 byte lengths, before transmitting such frames via FMAN, frames will need to be copied into a new single buffer or multiple buffer SG frame that is compliant with the three rules listed above. Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-07dpaa_eth: support all modes with rate adapting PHYsMadalin Bucur1-3/+11
Stop removing modes that are not supported on the system interface when the connected PHY is capable of rate adaptation. This addresses an issue with the LS1046ARDB board 10G interface no longer working with an 1G link partner after autonegotiation support was added for the Aquantia PHY on board in commit 09c4c57f7bc4 ("net: phy: aquantia: add support for auto-negotiation configuration") Before this commit the values advertised by the PHY were not influenced by the dpaa_eth driver removal of system-side unsupported modes as the aqr_config_aneg() was basically a no-op. After this commit, the modes removed by the dpaa_eth driver were no longer advertised thus autonegotiation with 1G link partners failed. Reported-by: Mian Yousaf Kaukab <ykaukab@suse.de> Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-31Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller1-19/+20
Simple overlapping changes in bpf land wrt. bpf_helper_defs.h handling. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-26dpaa_eth: fix DMA mapping leakMadalin Bucur1-19/+20
On the error path some fragments remain DMA mapped. Adding a fix that unmaps all the fragments. Rework cleanup path to be simpler. Fixes: 8151ee88bad5 ("dpaa_eth: use page backed rx buffers") Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-12-12netdev: pass the stuck queue to the timeout handlerMichael S. Tsirkin1-1/+1
This allows incrementing the correct timeout statistic without any mess. Down the road, devices can learn to reset just the specific queue. The patch was generated with the following script: use strict; use warnings; our $^I = '.bak'; my @work = ( ["arch/m68k/emu/nfeth.c", "nfeth_tx_timeout"], ["arch/um/drivers/net_kern.c", "uml_net_tx_timeout"], ["arch/um/drivers/vector_kern.c", "vector_net_tx_timeout"], ["arch/xtensa/platforms/iss/network.c", "iss_net_tx_timeout"], ["drivers/char/pcmcia/synclink_cs.c", "hdlcdev_tx_timeout"], ["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"], ["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"], ["drivers/message/fusion/mptlan.c", "mpt_lan_tx_timeout"], ["drivers/misc/sgi-xp/xpnet.c", "xpnet_dev_tx_timeout"], ["drivers/net/appletalk/cops.c", "cops_timeout"], ["drivers/net/arcnet/arcdevice.h", "arcnet_timeout"], ["drivers/net/arcnet/arcnet.c", "arcnet_timeout"], ["drivers/net/arcnet/com20020.c", "arcnet_timeout"], ["drivers/net/ethernet/3com/3c509.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c515.c", "corkscrew_timeout"], ["drivers/net/ethernet/3com/3c574_cs.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c589_cs.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"], ["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"], ["drivers/net/ethernet/3com/typhoon.c", "typhoon_tx_timeout"], ["drivers/net/ethernet/8390/8390.h", "ei_tx_timeout"], ["drivers/net/ethernet/8390/8390.h", "eip_tx_timeout"], ["drivers/net/ethernet/8390/8390.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/8390p.c", "eip_tx_timeout"], ["drivers/net/ethernet/8390/ax88796.c", "ax_ei_tx_timeout"], ["drivers/net/ethernet/8390/axnet_cs.c", "axnet_tx_timeout"], ["drivers/net/ethernet/8390/etherh.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/hydra.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/mac8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/mcf8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/lib8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/ne2k-pci.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/pcnet_cs.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/smc-ultra.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/wd.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/zorro8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/adaptec/starfire.c", "tx_timeout"], ["drivers/net/ethernet/agere/et131x.c", "et131x_tx_timeout"], ["drivers/net/ethernet/allwinner/sun4i-emac.c", "emac_timeout"], ["drivers/net/ethernet/alteon/acenic.c", "ace_watchdog"], ["drivers/net/ethernet/amazon/ena/ena_netdev.c", "ena_tx_timeout"], ["drivers/net/ethernet/amd/7990.h", "lance_tx_timeout"], ["drivers/net/ethernet/amd/7990.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/a2065.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/am79c961a.c", "am79c961_timeout"], ["drivers/net/ethernet/amd/amd8111e.c", "amd8111e_tx_timeout"], ["drivers/net/ethernet/amd/ariadne.c", "ariadne_tx_timeout"], ["drivers/net/ethernet/amd/atarilance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/au1000_eth.c", "au1000_tx_timeout"], ["drivers/net/ethernet/amd/declance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/lance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/mvme147.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/ni65.c", "ni65_timeout"], ["drivers/net/ethernet/amd/nmclan_cs.c", "mace_tx_timeout"], ["drivers/net/ethernet/amd/pcnet32.c", "pcnet32_tx_timeout"], ["drivers/net/ethernet/amd/sunlance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/xgbe/xgbe-drv.c", "xgbe_tx_timeout"], ["drivers/net/ethernet/apm/xgene-v2/main.c", "xge_timeout"], ["drivers/net/ethernet/apm/xgene/xgene_enet_main.c", "xgene_enet_timeout"], ["drivers/net/ethernet/apple/macmace.c", "mace_tx_timeout"], ["drivers/net/ethernet/atheros/ag71xx.c", "ag71xx_tx_timeout"], ["drivers/net/ethernet/atheros/alx/main.c", "alx_tx_timeout"], ["drivers/net/ethernet/atheros/atl1c/atl1c_main.c", "atl1c_tx_timeout"], ["drivers/net/ethernet/atheros/atl1e/atl1e_main.c", "atl1e_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl.c", "atlx_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl1.c", "atlx_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl2.c", "atl2_tx_timeout"], ["drivers/net/ethernet/broadcom/b44.c", "b44_tx_timeout"], ["drivers/net/ethernet/broadcom/bcmsysport.c", "bcm_sysport_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2.c", "bnx2_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnxt/bnxt.c", "bnxt_tx_timeout"], ["drivers/net/ethernet/broadcom/genet/bcmgenet.c", "bcmgenet_timeout"], ["drivers/net/ethernet/broadcom/sb1250-mac.c", "sbmac_tx_timeout"], ["drivers/net/ethernet/broadcom/tg3.c", "tg3_tx_timeout"], ["drivers/net/ethernet/calxeda/xgmac.c", "xgmac_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_main.c", "liquidio_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_vf_main.c", "liquidio_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_vf_rep.c", "lio_vf_rep_tx_timeout"], ["drivers/net/ethernet/cavium/thunder/nicvf_main.c", "nicvf_tx_timeout"], ["drivers/net/ethernet/cirrus/cs89x0.c", "net_timeout"], ["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"], ["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"], ["drivers/net/ethernet/cortina/gemini.c", "gmac_tx_timeout"], ["drivers/net/ethernet/davicom/dm9000.c", "dm9000_timeout"], ["drivers/net/ethernet/dec/tulip/de2104x.c", "de_tx_timeout"], ["drivers/net/ethernet/dec/tulip/tulip_core.c", "tulip_tx_timeout"], ["drivers/net/ethernet/dec/tulip/winbond-840.c", "tx_timeout"], ["drivers/net/ethernet/dlink/dl2k.c", "rio_tx_timeout"], ["drivers/net/ethernet/dlink/sundance.c", "tx_timeout"], ["drivers/net/ethernet/emulex/benet/be_main.c", "be_tx_timeout"], ["drivers/net/ethernet/ethoc.c", "ethoc_tx_timeout"], ["drivers/net/ethernet/faraday/ftgmac100.c", "ftgmac100_tx_timeout"], ["drivers/net/ethernet/fealnx.c", "fealnx_tx_timeout"], ["drivers/net/ethernet/freescale/dpaa/dpaa_eth.c", "dpaa_tx_timeout"], ["drivers/net/ethernet/freescale/fec_main.c", "fec_timeout"], ["drivers/net/ethernet/freescale/fec_mpc52xx.c", "mpc52xx_fec_tx_timeout"], ["drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c", "fs_timeout"], ["drivers/net/ethernet/freescale/gianfar.c", "gfar_timeout"], ["drivers/net/ethernet/freescale/ucc_geth.c", "ucc_geth_timeout"], ["drivers/net/ethernet/fujitsu/fmvj18x_cs.c", "fjn_tx_timeout"], ["drivers/net/ethernet/google/gve/gve_main.c", "gve_tx_timeout"], ["drivers/net/ethernet/hisilicon/hip04_eth.c", "hip04_timeout"], ["drivers/net/ethernet/hisilicon/hix5hd2_gmac.c", "hix5hd2_net_timeout"], ["drivers/net/ethernet/hisilicon/hns/hns_enet.c", "hns_nic_net_timeout"], ["drivers/net/ethernet/hisilicon/hns3/hns3_enet.c", "hns3_nic_net_timeout"], ["drivers/net/ethernet/huawei/hinic/hinic_main.c", "hinic_tx_timeout"], ["drivers/net/ethernet/i825xx/82596.c", "i596_tx_timeout"], ["drivers/net/ethernet/i825xx/ether1.c", "ether1_timeout"], ["drivers/net/ethernet/i825xx/lib82596.c", "i596_tx_timeout"], ["drivers/net/ethernet/i825xx/sun3_82586.c", "sun3_82586_timeout"], ["drivers/net/ethernet/ibm/ehea/ehea_main.c", "ehea_tx_watchdog"], ["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"], ["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"], ["drivers/net/ethernet/ibm/ibmvnic.c", "ibmvnic_tx_timeout"], ["drivers/net/ethernet/intel/e100.c", "e100_tx_timeout"], ["drivers/net/ethernet/intel/e1000/e1000_main.c", "e1000_tx_timeout"], ["drivers/net/ethernet/intel/e1000e/netdev.c", "e1000_tx_timeout"], ["drivers/net/ethernet/intel/fm10k/fm10k_netdev.c", "fm10k_tx_timeout"], ["drivers/net/ethernet/intel/i40e/i40e_main.c", "i40e_tx_timeout"], ["drivers/net/ethernet/intel/iavf/iavf_main.c", "iavf_tx_timeout"], ["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"], ["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"], ["drivers/net/ethernet/intel/igb/igb_main.c", "igb_tx_timeout"], ["drivers/net/ethernet/intel/igbvf/netdev.c", "igbvf_tx_timeout"], ["drivers/net/ethernet/intel/ixgb/ixgb_main.c", "ixgb_tx_timeout"], ["drivers/net/ethernet/intel/ixgbe/ixgbe_debugfs.c", "adapter->netdev->netdev_ops->ndo_tx_timeout(adapter->netdev);"], ["drivers/net/ethernet/intel/ixgbe/ixgbe_main.c", "ixgbe_tx_timeout"], ["drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c", "ixgbevf_tx_timeout"], ["drivers/net/ethernet/jme.c", "jme_tx_timeout"], ["drivers/net/ethernet/korina.c", "korina_tx_timeout"], ["drivers/net/ethernet/lantiq_etop.c", "ltq_etop_tx_timeout"], ["drivers/net/ethernet/marvell/mv643xx_eth.c", "mv643xx_eth_tx_timeout"], ["drivers/net/ethernet/marvell/pxa168_eth.c", "pxa168_eth_tx_timeout"], ["drivers/net/ethernet/marvell/skge.c", "skge_tx_timeout"], ["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"], ["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"], ["drivers/net/ethernet/mediatek/mtk_eth_soc.c", "mtk_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx5/core/en_main.c", "mlx5e_tx_timeout"], ["drivers/net/ethernet/micrel/ks8842.c", "ks8842_tx_timeout"], ["drivers/net/ethernet/micrel/ksz884x.c", "netdev_tx_timeout"], ["drivers/net/ethernet/microchip/enc28j60.c", "enc28j60_tx_timeout"], ["drivers/net/ethernet/microchip/encx24j600.c", "encx24j600_tx_timeout"], ["drivers/net/ethernet/natsemi/sonic.h", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/sonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/jazzsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/macsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/natsemi.c", "ns_tx_timeout"], ["drivers/net/ethernet/natsemi/ns83820.c", "ns83820_tx_timeout"], ["drivers/net/ethernet/natsemi/xtsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/neterion/s2io.h", "s2io_tx_watchdog"], ["drivers/net/ethernet/neterion/s2io.c", "s2io_tx_watchdog"], ["drivers/net/ethernet/neterion/vxge/vxge-main.c", "vxge_tx_watchdog"], ["drivers/net/ethernet/netronome/nfp/nfp_net_common.c", "nfp_net_tx_timeout"], ["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"], ["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"], ["drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c", "pch_gbe_tx_timeout"], ["drivers/net/ethernet/packetengines/hamachi.c", "hamachi_tx_timeout"], ["drivers/net/ethernet/packetengines/yellowfin.c", "yellowfin_tx_timeout"], ["drivers/net/ethernet/pensando/ionic/ionic_lif.c", "ionic_tx_timeout"], ["drivers/net/ethernet/qlogic/netxen/netxen_nic_main.c", "netxen_tx_timeout"], ["drivers/net/ethernet/qlogic/qla3xxx.c", "ql3xxx_tx_timeout"], ["drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c", "qlcnic_tx_timeout"], ["drivers/net/ethernet/qualcomm/emac/emac.c", "emac_tx_timeout"], ["drivers/net/ethernet/qualcomm/qca_spi.c", "qcaspi_netdev_tx_timeout"], ["drivers/net/ethernet/qualcomm/qca_uart.c", "qcauart_netdev_tx_timeout"], ["drivers/net/ethernet/rdc/r6040.c", "r6040_tx_timeout"], ["drivers/net/ethernet/realtek/8139cp.c", "cp_tx_timeout"], ["drivers/net/ethernet/realtek/8139too.c", "rtl8139_tx_timeout"], ["drivers/net/ethernet/realtek/atp.c", "tx_timeout"], ["drivers/net/ethernet/realtek/r8169_main.c", "rtl8169_tx_timeout"], ["drivers/net/ethernet/renesas/ravb_main.c", "ravb_tx_timeout"], ["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"], ["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"], ["drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c", "sxgbe_tx_timeout"], ["drivers/net/ethernet/seeq/ether3.c", "ether3_timeout"], ["drivers/net/ethernet/seeq/sgiseeq.c", "timeout"], ["drivers/net/ethernet/sfc/efx.c", "efx_watchdog"], ["drivers/net/ethernet/sfc/falcon/efx.c", "ef4_watchdog"], ["drivers/net/ethernet/sgi/ioc3-eth.c", "ioc3_timeout"], ["drivers/net/ethernet/sgi/meth.c", "meth_tx_timeout"], ["drivers/net/ethernet/silan/sc92031.c", "sc92031_tx_timeout"], ["drivers/net/ethernet/sis/sis190.c", "sis190_tx_timeout"], ["drivers/net/ethernet/sis/sis900.c", "sis900_tx_timeout"], ["drivers/net/ethernet/smsc/epic100.c", "epic_tx_timeout"], ["drivers/net/ethernet/smsc/smc911x.c", "smc911x_timeout"], ["drivers/net/ethernet/smsc/smc9194.c", "smc_timeout"], ["drivers/net/ethernet/smsc/smc91c92_cs.c", "smc_tx_timeout"], ["drivers/net/ethernet/smsc/smc91x.c", "smc_timeout"], ["drivers/net/ethernet/stmicro/stmmac/stmmac_main.c", "stmmac_tx_timeout"], ["drivers/net/ethernet/sun/cassini.c", "cas_tx_timeout"], ["drivers/net/ethernet/sun/ldmvsw.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/niu.c", "niu_tx_timeout"], ["drivers/net/ethernet/sun/sunbmac.c", "bigmac_tx_timeout"], ["drivers/net/ethernet/sun/sungem.c", "gem_tx_timeout"], ["drivers/net/ethernet/sun/sunhme.c", "happy_meal_tx_timeout"], ["drivers/net/ethernet/sun/sunqe.c", "qe_tx_timeout"], ["drivers/net/ethernet/sun/sunvnet.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/sunvnet_common.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/sunvnet_common.h", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/synopsys/dwc-xlgmac-net.c", "xlgmac_tx_timeout"], ["drivers/net/ethernet/ti/cpmac.c", "cpmac_tx_timeout"], ["drivers/net/ethernet/ti/cpsw.c", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/cpsw_priv.c", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/cpsw_priv.h", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/davinci_emac.c", "emac_dev_tx_timeout"], ["drivers/net/ethernet/ti/netcp_core.c", "netcp_ndo_tx_timeout"], ["drivers/net/ethernet/ti/tlan.c", "tlan_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_net.h", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_net.c", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_wireless.c", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/spider_net.c", "spider_net_tx_timeout"], ["drivers/net/ethernet/toshiba/tc35815.c", "tc35815_tx_timeout"], ["drivers/net/ethernet/via/via-rhine.c", "rhine_tx_timeout"], ["drivers/net/ethernet/wiznet/w5100.c", "w5100_tx_timeout"], ["drivers/net/ethernet/wiznet/w5300.c", "w5300_tx_timeout"], ["drivers/net/ethernet/xilinx/xilinx_emaclite.c", "xemaclite_tx_timeout"], ["drivers/net/ethernet/xircom/xirc2ps_cs.c", "xirc_tx_timeout"], ["drivers/net/fjes/fjes_main.c", "fjes_tx_retry"], ["drivers/net/slip/slip.c", "sl_tx_timeout"], ["include/linux/usb/usbnet.h", "usbnet_tx_timeout"], ["drivers/net/usb/aqc111.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/ax88172a.c", "usbnet_tx_timeout"], ["drivers/net/usb/ax88179_178a.c", "usbnet_tx_timeout"], ["drivers/net/usb/catc.c", "catc_tx_timeout"], ["drivers/net/usb/cdc_mbim.c", "usbnet_tx_timeout"], ["drivers/net/usb/cdc_ncm.c", "usbnet_tx_timeout"], ["drivers/net/usb/dm9601.c", "usbnet_tx_timeout"], ["drivers/net/usb/hso.c", "hso_net_tx_timeout"], ["drivers/net/usb/int51x1.c", "usbnet_tx_timeout"], ["drivers/net/usb/ipheth.c", "ipheth_tx_timeout"], ["drivers/net/usb/kaweth.c", "kaweth_tx_timeout"], ["drivers/net/usb/lan78xx.c", "lan78xx_tx_timeout"], ["drivers/net/usb/mcs7830.c", "usbnet_tx_timeout"], ["drivers/net/usb/pegasus.c", "pegasus_tx_timeout"], ["drivers/net/usb/qmi_wwan.c", "usbnet_tx_timeout"], ["drivers/net/usb/r8152.c", "rtl8152_tx_timeout"], ["drivers/net/usb/rndis_host.c", "usbnet_tx_timeout"], ["drivers/net/usb/rtl8150.c", "rtl8150_tx_timeout"], ["drivers/net/usb/sierra_net.c", "usbnet_tx_timeout"], ["drivers/net/usb/smsc75xx.c", "usbnet_tx_timeout"], ["drivers/net/usb/smsc95xx.c", "usbnet_tx_timeout"], ["drivers/net/usb/sr9700.c", "usbnet_tx_timeout"], ["drivers/net/usb/sr9800.c", "usbnet_tx_timeout"], ["drivers/net/usb/usbnet.c", "usbnet_tx_timeout"], ["drivers/net/vmxnet3/vmxnet3_drv.c", "vmxnet3_tx_timeout"], ["drivers/net/wan/cosa.c", "cosa_net_timeout"], ["drivers/net/wan/farsync.c", "fst_tx_timeout"], ["drivers/net/wan/fsl_ucc_hdlc.c", "uhdlc_tx_timeout"], ["drivers/net/wan/lmc/lmc_main.c", "lmc_driver_timeout"], ["drivers/net/wan/x25_asy.c", "x25_asy_timeout"], ["drivers/net/wimax/i2400m/netdev.c", "i2400m_tx_timeout"], ["drivers/net/wireless/intel/ipw2x00/ipw2100.c", "ipw2100_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/main.c", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/orinoco_usb.c", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/orinoco.h", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_dev.c", "islpci_eth_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_eth.c", "islpci_eth_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_eth.h", "islpci_eth_tx_timeout"], ["drivers/net/wireless/marvell/mwifiex/main.c", "mwifiex_tx_timeout"], ["drivers/net/wireless/quantenna/qtnfmac/core.c", "qtnf_netdev_tx_timeout"], ["drivers/net/wireless/quantenna/qtnfmac/core.h", "qtnf_netdev_tx_timeout"], ["drivers/net/wireless/rndis_wlan.c", "usbnet_tx_timeout"], ["drivers/net/wireless/wl3501_cs.c", "wl3501_tx_timeout"], ["drivers/net/wireless/zydas/zd1201.c", "zd1201_tx_timeout"], ["drivers/s390/net/qeth_core.h", "qeth_tx_timeout"], ["drivers/s390/net/qeth_core_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"], ["drivers/staging/ks7010/ks_wlan_net.c", "ks_wlan_tx_timeout"], ["drivers/staging/qlge/qlge_main.c", "qlge_tx_timeout"], ["drivers/staging/rtl8192e/rtl8192e/rtl_core.c", "_rtl92e_tx_timeout"], ["drivers/staging/rtl8192u/r8192U_core.c", "tx_timeout"], ["drivers/staging/unisys/visornic/visornic_main.c", "visornic_xmit_timeout"], ["drivers/staging/wlan-ng/p80211netdev.c", "p80211knetdev_tx_timeout"], ["drivers/tty/n_gsm.c", "gsm_mux_net_tx_timeout"], ["drivers/tty/synclink.c", "hdlcdev_tx_timeout"], ["drivers/tty/synclink_gt.c", "hdlcdev_tx_timeout"], ["drivers/tty/synclinkmp.c", "hdlcdev_tx_timeout"], ["net/atm/lec.c", "lec_tx_timeout"], ["net/bluetooth/bnep/netdev.c", "bnep_net_timeout"] ); for my $p (@work) { my @pair = @$p; my $file = $pair[0]; my $func = $pair[1]; print STDERR $file , ": ", $func,"\n"; our @ARGV = ($file); while (<ARGV>) { if (m/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/) { print STDERR "found $1+$2 in $file\n"; } if (s/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/$1, unsigned int txqueue$2/) { print STDERR "$func found in $file\n"; } print; } } where the list of files and functions is simply from: git grep ndo_tx_timeout, with manual addition of headers in the rare cases where the function is from a header, then manually changing the few places which actually call ndo_tx_timeout. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Heiner Kallweit <hkallweit1@gmail.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Shannon Nelson <snelson@pensando.io> Reviewed-by: Martin Habets <mhabets@solarflare.com> changes from v9: fixup a forward declaration changes from v9: more leftovers from v3 change changes from v8: fix up a missing direct call to timeout rebased on net-next changes from v7: fixup leftovers from v3 change changes from v6: fix typo in rtl driver changes from v5: add missing files (allow any net device argument name) changes from v4: add a missing driver header changes from v3: change queue # to unsigned Changes from v2: added headers Changes from v1: Fix errors found by kbuild: generalize the pattern a bit, to pick up a couple of instances missed by the previous version. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-31dpaa_eth: register a device link for the qman portal usedMadalin Bucur1-2/+3
Before this change, unbinding the QMan portals did not trigger a corresponding unbinding of the dpaa_eth making use of it; the first QMan portal related operation issued afterwards crashed the kernel. The device link ensures the dpaa_eth dependency upon the qman portal used is honoured at the QMan portal removal. Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-31dpaa_eth: extend delays in ndo_stopMadalin Bucur1-1/+3
Make sure all the frames that are in flight have time to be processed before the interface is completely brought down. Add a missing delay for the Rx path. Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-31dpaa_eth: use a page to store the SGTMadalin Bucur1-22/+21
Use a page to store the scatter gather table on the transmit path. Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-31dpaa_eth: cleanup skb_to_contig_fd()Madalin Bucur1-7/+7
Remove cast, align variable name, simplify DMA map size computation. Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-31dpaa_eth: use fd information in dpaa_cleanup_tx_fd()Madalin Bucur1-6/+7
Instead of reading skb fields, use information from the DPAA frame descriptor. Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-31dpaa_eth: simplify variables used in dpaa_cleanup_tx_fd()Madalin Bucur1-7/+7
Avoid casts and repeated conversions. Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-31dpaa_eth: avoid timestamp read on error pathsMadalin Bucur1-7/+10
The dpaa_cleanup_tx_fd() function is called by the frame transmit confirmation callback but also on several error paths. This function is reading the transmit timestamp value. Avoid reading an invalid timestamp value on the error paths. Fixes: 4664856e9ca2 ("dpaa_eth: add support for hardware timestamping") Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-31dpaa_eth: perform DMA unmapping before readMadalin Bucur1-15/+17
DMA unmapping is required before accessing the HW provided timestamping information. Fixes: 4664856e9ca2 ("dpaa_eth: add support for hardware timestamping") Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-31dpaa_eth: use page backed rx buffersMadalin Bucur1-29/+22
Change the buffers used for reception from netdev_frags to pages. Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-31dpaa_eth: use only one buffer pool per interfaceMadalin Bucur1-60/+35
Currently the DPAA Ethernet driver is using three buffer pools for each interface, with three different sizes for the buffers provided for the FMan reception path. This patch reduces the number of buffer pools to one per interface. This change is in preparation of another, that will be switching from netdev_frags to page backed buffers for the receive path. Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-24dpaa_eth: add newline in dev_err() msgMadalin Bucur1-1/+1
Newline was missing at the end of the error message. Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-24dpaa_eth: change DMA deviceMadalin Bucur1-49/+56
The DPAA Ethernet driver is using the FMan MAC as the device for DMA mapping. This is not actually correct, as the real DMA device is the FMan port (the FMan Rx port for reception and the FMan Tx port for transmission). Changing the device used for DMA mapping to the Fman Rx and Tx port devices. Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-24dpaa_eth: remove redundant codeMadalin Bucur1-4/+0
Condition was previously checked, removing duplicate code. Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-24dpaa_eth: defer probing after qbmanLaurentiu Tudor1-0/+31
If the DPAA 1 Ethernet driver gets probed before the QBMan driver it will cause a boot crash. Add predictability in the probing order by deferring the Ethernet driver probe after QBMan and portals by using the recently introduced QBMan APIs. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-08dpaa_eth: Use refcount_t for refcountChuhong Yuan1-3/+3
refcount_t is better for reference counters since its implementation can prevent overflows. So convert atomic_t ref counters to refcount_t. Signed-off-by: Chuhong Yuan <hslester96@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-07-24Build fixes for skb_frag_size conversionMatthew Wilcox (Oracle)1-1/+1
I missed a few places. One is in some ifdeffed code which will probably never be re-enabled; the others are in drivers which can't currently be compiled on x86. Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-28dpaa_eth: use only online CPU portalsMadalin Bucur1-5/+4
Make sure only the portals for the online CPUs are used. Without this change, there are issues when someone boots with maxcpus=n, with n < actual number of cores available as frames either received or corresponding to the transmit confirmation path would be offered for dequeue to the offline CPU portals, getting lost. Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-05dpaa_eth: fix SG frame cleanupLaurentiu Tudor1-1/+1
Fix issue with the entry indexing in the sg frame cleanup code being off-by-1. This problem showed up when doing some basic iperf tests and manifested in traffic coming to a halt. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Acked-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-17dpaa_eth: NETIF_F_LLTX requires to do our own update of trans_startMadalin Bucur1-0/+6
As txq_trans_update() only updates trans_start when the lock is held, trans_start does not get updated if NETIF_F_LLTX is declared. Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-17dpaa_eth: Add change_carrier() for Fixed PHYsJoakim Tjernlund1-1/+2
This allows to control carrier from /sys/class/net/ethX/carrier for Fixed PHYs. Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11net: ethernet: Convert phydev advertize and supported from u32 to link modeAndrew Lunn1-1/+4
There are a few MAC/PHYs combinations which now support > 1Gbps. These may need to make use of link modes with bits > 31. Thus their supported PHY features or advertised features cannot be implemented using the current bitmap in a u32. Convert to using a linkmode bitmap, which can support all the currently devices link modes, and is future proof as more modes are added. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-02dpaa_eth: Remove useless declarationNathan Chancellor1-2/+0
Clang warns: drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:2734:34: warning: tentative array definition assumed to have one element static const struct of_device_id dpaa_match[]; ^ 1 warning generated. Turns out that since this driver was introduced in commit 9ad1a3749333 ("dpaa_eth: add support for DPAA Ethernet"), this declaration has been unused. Remove it to silence the warning. Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Acked-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-21net: freescale: fix return type of ndo_start_xmit functionYueHaibing1-1/+2
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t', which is a typedef for an enum type, so make sure the implementation in this driver has returns 'netdev_tx_t' value, and change the function return type to netdev_tx_t. Found by coccinelle. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-12net: ethernet: Add helper for MACs which support asym pauseAndrew Lunn1-2/+1
Rather than have the MAC drivers manipulate phydev members to indicate they support Asym Pause, add a helper function. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-07freescale: ethernet: remove unnecessary unlikely()Igor Stoppa1-5/+3
Both WARN_ON() and WARN_ONCE() already contain an unlikely(), so it's not necessary to wrap it into another. Signed-off-by: Igor Stoppa <igor.stoppa@huawei.com> Cc: Madalin Bucur <madalin.bucur@nxp.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-03Merge ra.kernel.org:/pub/scm/linux/kernel/git/davem/netDavid S. Miller1-7/+8
Simple overlapping changes in stmmac driver. Adjust skb_gro_flush_final_remcsum function signature to make GRO list changes in net-next, as per Stephen Rothwell's example merge resolution. Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-30dpaa_eth: DPAA SGT needs to be 256BMadalin Bucur1-7/+8
The DPAA HW requires that at least 256 bytes from the start of the first scatter-gather table entry are allocated and accessible. The hardware reads the maximum size the table can have in one access, thus requiring that the allocation and mapping to be done for the maximum size of 256B even if there is a smaller number of entries in the table. Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-26dpaa_eth: add support for hardware timestampingYangbo Lu1-5/+83
This patch is to add hardware timestamping support for dpaa_eth. On Rx, timestamping is enabled for all frames. On Tx, we only instruct the hardware to timestamp the frames marked accordingly by the stack. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Acked-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-12treewide: devm_kzalloc() -> devm_kcalloc()Kees Cook1-1/+1
The devm_kzalloc() function has a 2-factor argument form, devm_kcalloc(). This patch replaces cases of: devm_kzalloc(handle, a * b, gfp) with: devm_kcalloc(handle, a * b, gfp) as well as handling cases of: devm_kzalloc(handle, a * b * c, gfp) with: devm_kzalloc(handle, array3_size(a, b, c), gfp) as it's slightly less ugly than: devm_kcalloc(handle, array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: devm_kzalloc(handle, 4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. Some manual whitespace fixes were needed in this patch, as Coccinelle really liked to write "=devm_kcalloc..." instead of "= devm_kcalloc...". The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ expression HANDLE; type TYPE; expression THING, E; @@ ( devm_kzalloc(HANDLE, - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | devm_kzalloc(HANDLE, - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression HANDLE; expression COUNT; typedef u8; typedef __u8; @@ ( devm_kzalloc(HANDLE, - sizeof(u8) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(__u8) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(char) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(unsigned char) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(u8) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(__u8) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(char) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ expression HANDLE; type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ expression HANDLE; identifier SIZE, COUNT; @@ - devm_kzalloc + devm_kcalloc (HANDLE, - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression HANDLE; expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( devm_kzalloc(HANDLE, - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression HANDLE; expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ expression HANDLE; identifier STRIDE, SIZE, COUNT; @@ ( devm_kzalloc(HANDLE, - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression HANDLE; expression E1, E2, E3; constant C1, C2, C3; @@ ( devm_kzalloc(HANDLE, C1 * C2 * C3, ...) | devm_kzalloc(HANDLE, - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression HANDLE; expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( devm_kzalloc(HANDLE, sizeof(THING) * C2, ...) | devm_kzalloc(HANDLE, sizeof(TYPE) * C2, ...) | devm_kzalloc(HANDLE, C1 * C2 * C3, ...) | devm_kzalloc(HANDLE, C1 * C2, ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - (E1) * E2 + E1, E2 , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - (E1) * (E2) + E1, E2 , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-03-23Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller1-4/+4
Fun set of conflict resolutions here... For the mac80211 stuff, these were fortunately just parallel adds. Trivially resolved. In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the function phy_disable_interrupts() earlier in the file, whilst in 'net-next' the phy_error() call from this function was removed. In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the 'rt_table_id' member of rtable collided with a bug fix in 'net' that added a new struct member "rt_mtu_locked" which needs to be copied over here. The mlxsw driver conflict consisted of net-next separating the span code and definitions into separate files, whilst a 'net' bug fix made some changes to that moved code. The mlx5 infiniband conflict resolution was quite non-trivial, the RDMA tree's merge commit was used as a guide here, and here are their notes: ==================== Due to bug fixes found by the syzkaller bot and taken into the for-rc branch after development for the 4.17 merge window had already started being taken into the for-next branch, there were fairly non-trivial merge issues that would need to be resolved between the for-rc branch and the for-next branch. This merge resolves those conflicts and provides a unified base upon which ongoing development for 4.17 can be based. Conflicts: drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f9524 (IB/mlx5: Fix cleanup order on unload) added to for-rc and commit b5ca15ad7e61 (IB/mlx5: Add proper representors support) add as part of the devel cycle both needed to modify the init/de-init functions used by mlx5. To support the new representors, the new functions added by the cleanup patch needed to be made non-static, and the init/de-init list added by the representors patch needed to be modified to match the init/de-init list changes made by the cleanup patch. Updates: drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function prototypes added by representors patch to reflect new function names as changed by cleanup patch drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init stage list to match new order from cleanup patch ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-14dpaa_eth: remove duplicate increment of the tx_errors counterCamelia Groza1-1/+0
The tx_errors counter is incremented by the dpaa_xmit caller. Signed-off-by: Camelia Groza <camelia.groza@nxp.com> Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-14dpaa_eth: increment the RX dropped counter when neededCamelia Groza1-1/+3
Signed-off-by: Camelia Groza <camelia.groza@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-14dpaa_eth: remove duplicate initializationCamelia Groza1-1/+0
The fd_format has already been initialized at this point. Signed-off-by: Camelia Groza <camelia.groza@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-03-14dpaa_eth: fix error in dpaa_remove()Madalin Bucur1-1/+1
The recent changes that make the driver probing compatible with DSA were not propagated in the dpa_remove() function, breaking the module unload function. Using the proper device to address the issue. Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-27dpaa_eth: Add allmulti optionRadu Bulie1-0/+10
This patch adds allmulticast option for memac, dtsec and 10GEC controllers. Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-27dpaa_eth: refactor frag count checkingMadalin Bucur1-8/+12
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-27dpaa_eth: make sure all Rx errors are countedMadalin Bucur1-8/+2
Simplify the code and avoid some Rx errors not being accounted. Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-27dpaa_eth: fix SG mappingMadalin Bucur1-10/+13
An issue in the code mapping the skb fragments into scatter-gather frames was evidentiated by netperf TCP_SENDFILE tests. The size was set wrong for all fragments but the first, affecting the transmission of any skb with more than one fragment. Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-13dpaa_eth: fix incorrect commentJake Moroni1-1/+1
The comment stated that a thread was started, but that is not the case. Signed-off-by: Jake Moroni <mail@jakemoroni.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-08dpaa_eth: fix error return code in dpaa_eth_probe()Wei Yongjun1-3/+3
Fix to return a negative error code from the dpaa_bp_alloc() error handling case instead of 0, as done elsewhere in this function. Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-08net_sch: mqprio: Change TC_SETUP_MQPRIO to TC_SETUP_QDISC_MQPRIONogah Frankel1-1/+1
Change TC_SETUP_MQPRIO to TC_SETUP_QDISC_MQPRIO to match the new convention. Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-05dpaa_eth: avoid uninitialized variable false-positive warningArnd Bergmann1-1/+2
We can now build this driver on ARM, so I ran into a randconfig build warning that presumably had existed on powerpc already. drivers/net/ethernet/freescale/dpaa/dpaa_eth.c: In function 'sg_fd_to_skb': drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:1712:18: error: 'skb' may be used uninitialized in this function [-Werror=maybe-uninitialized] I'm slightly changing the logic here, to make it obvious to the compiler that 'skb' is always initialized. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-02net: dpaa: remove init which already done in per-cpu allocationyuan linyu1-5/+0
Signed-off-by: yuan linyu <Linyu.Yuan@alcatel-sbell.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-02net: dpaa: fix maybe uninitialized var in dpaa_open()yuan linyu1-1/+2
Signed-off-by: yuan linyu <Linyu.Yuan@alcatel-sbell.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.