| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Only set the device carrier state to on after receiving an up link
state indication from the underlying adapter. Likewise, if a down
link indication is receieved, update the carrier state accordingly.
This fix ensures that accurate carrier state is reported by the driver
following a link state update by the underlying adapter.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was discovered in testing that the underlying hardware MAC
address will revert to initial settings following a device reset,
but the driver fails to resend the current OS MAC settings. This
oversight can result in dropped packets should the scenario occur.
Fix this by informing hardware of current MAC address settings
following any adapter initialization or resets.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ibmvnic driver currently uses the same fixed name when using
request_irq, this makes it hard to parse when multiple VNIC devices are
available at the same time. This patch adds the unit_address as the device
identification along with an id for each queue.
The original idea was to use the interface name as an identifier, but it
is not feasible given these requests happen at adapter probe, and at this
point netdev is not yet registered so it doesn't have the proper name
assigned to it.
Signed-off-by: Murilo Fossa Vicentini <muvic@linux.ibm.com>
Reviewed-by: Mauro S. M. Rodrigues <maurosr@linux.vnet.ibm.com>
Reviewed-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflict resolution of af_smc.c from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While determining offload capabilities of backing hardware during
a device reset, the driver is clobbering current feature settings.
Update hw_features on reset instead of features unless a feature
is enabled that is no longer supported on the current backing device.
Also enable features that were not supported prior to the reset but
were previously enabled or requested by the user.
This can occur if the reset is the result of a carrier change, such
as a device failover or partition migration.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable Generic Receive Offload in the ibmvnic driver.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor comment merge conflict in mlx5.
Staging driver has a fixup due to the skb->xmit_more changes
in 'net-next', but was removed in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix device initialization completion handling for vNIC adapters.
Initialize the completion structure on probe and reinitialize when needed.
This also fixes a race condition during kdump where the driver can attempt
to access the completion struct before it is initialized:
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc0000000081acbe0
Oops: Kernel access of bad area, sig: 11 [#1]
LE SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: ibmvnic(+) ibmveth sunrpc overlay squashfs loop
CPU: 19 PID: 301 Comm: systemd-udevd Not tainted 4.18.0-64.el8.ppc64le #1
NIP: c0000000081acbe0 LR: c0000000081ad964 CTR: c0000000081ad900
REGS: c000000027f3f990 TRAP: 0300 Not tainted (4.18.0-64.el8.ppc64le)
MSR: 800000010280b033 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI,LE,TM[E]> CR: 28228288 XER: 00000006
CFAR: c000000008008934 DAR: 0000000000000000 DSISR: 40000000 IRQMASK: 1
GPR00: c0000000081ad964 c000000027f3fc10 c0000000095b5800 c0000000221b4e58
GPR04: 0000000000000003 0000000000000001 000049a086918581 00000000000000d4
GPR08: 0000000000000007 0000000000000000 ffffffffffffffe8 d0000000014dde28
GPR12: c0000000081ad900 c000000009a00c00 0000000000000001 0000000000000100
GPR16: 0000000000000038 0000000000000007 c0000000095e2230 0000000000000006
GPR20: 0000000000400140 0000000000000001 c00000000910c880 0000000000000000
GPR24: 0000000000000000 0000000000000006 0000000000000000 0000000000000003
GPR28: 0000000000000001 0000000000000001 c0000000221b4e60 c0000000221b4e58
NIP [c0000000081acbe0] __wake_up_locked+0x50/0x100
LR [c0000000081ad964] complete+0x64/0xa0
Call Trace:
[c000000027f3fc10] [c000000027f3fc60] 0xc000000027f3fc60 (unreliable)
[c000000027f3fc60] [c0000000081ad964] complete+0x64/0xa0
[c000000027f3fca0] [d0000000014dad58] ibmvnic_handle_crq+0xce0/0x1160 [ibmvnic]
[c000000027f3fd50] [d0000000014db270] ibmvnic_tasklet+0x98/0x130 [ibmvnic]
[c000000027f3fda0] [c00000000813f334] tasklet_action_common.isra.3+0xc4/0x1a0
[c000000027f3fe00] [c000000008cd13f4] __do_softirq+0x164/0x400
[c000000027f3fef0] [c00000000813ed64] irq_exit+0x184/0x1c0
[c000000027f3ff20] [c0000000080188e8] __do_irq+0xb8/0x210
[c000000027f3ff90] [c00000000802d0a4] call_do_irq+0x14/0x24
[c000000026a5b010] [c000000008018adc] do_IRQ+0x9c/0x130
[c000000026a5b060] [c000000008008ce4] hardware_interrupt_common+0x114/0x120
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/ibm/ibmvnic.c: In function '__ibmvnic_reset':
drivers/net/ethernet/ibm/ibmvnic.c:1971:21: warning: variable 'netdev' set but not used [-Wunused-but-set-variable]
It's never used since introduction in
commit ed651a10875f ("ibmvnic: Updated reset handling")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ibmvnic driver currently reports a fixed value for both speed and
duplex settings regardless of the actual backing device that is being
used. By adding support to the QUERY_PHYS_PARMS command defined by the
PAPR+ we can query the current physical port state and report the proper
values for these feilds.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Murilo Fossa Vicentini <muvic@linux.ibm.com>
Reviewed-by: Mauro S. M. Rodrigues <maurosr@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver was checking for non-NULL address.
- adapter->napi[i]
This is pointless as these will be always non-NULL, since the
'dapter->napi' is allocated in init_napi().
It is safe to get rid of useless checks for addresses to fix the
coccinelle warning:
>>drivers/net/ethernet/ibm/ibmvnic.c: test of a variable/field address
Since such statements always return true, they are redundant.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
CC: Michael Ellerman <mpe@ellerman.id.au>
CC: Thomas Falcon <tlfalcon@linux.ibm.com>
CC: John Allen <jallen@linux.ibm.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: linuxppc-dev@lists.ozlabs.org
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ibmvnic_reset allocated new reset work item objects in a non-atomic
context. This can be called from a tasklet, generating the output below.
Allocate work items with the GFP_ATOMIC flag instead.
BUG: sleeping function called from invalid context at mm/slab.h:421
in_atomic(): 1, irqs_disabled(): 1, pid: 93, name: kworker/0:2
INFO: lockdep is turned off.
irq event stamp: 66049
hardirqs last enabled at (66048): [<c000000000122468>] tasklet_action_common.isra.12+0x78/0x1c0
hardirqs last disabled at (66049): [<c000000000befce8>] _raw_spin_lock_irqsave+0x48/0xf0
softirqs last enabled at (66044): [<c000000000a8ac78>] dev_deactivate_queue.constprop.28+0xc8/0x160
softirqs last disabled at (66045): [<c0000000000306e0>] call_do_softirq+0x14/0x24
CPU: 0 PID: 93 Comm: kworker/0:2 Kdump: loaded Not tainted 4.20.0-rc6-00001-g1b50a8f03706 #7
Workqueue: events linkwatch_event
Call Trace:
[c0000003fffe7ae0] [c000000000bc83e4] dump_stack+0xe8/0x164 (unreliable)
[c0000003fffe7b30] [c00000000015ba0c] ___might_sleep+0x2dc/0x320
[c0000003fffe7bb0] [c000000000391514] kmem_cache_alloc_trace+0x3e4/0x440
[c0000003fffe7c30] [d000000005b2309c] ibmvnic_reset+0x16c/0x360 [ibmvnic]
[c0000003fffe7cc0] [d000000005b29834] ibmvnic_tasklet+0x1054/0x2010 [ibmvnic]
[c0000003fffe7e00] [c0000000001224c8] tasklet_action_common.isra.12+0xd8/0x1c0
[c0000003fffe7e60] [c000000000bf1238] __do_softirq+0x1a8/0x64c
[c0000003fffe7f90] [c0000000000306e0] call_do_softirq+0x14/0x24
[c0000003f3967980] [c00000000001ba50] do_softirq_own_stack+0x60/0xb0
[c0000003f39679c0] [c0000000001218a8] do_softirq+0xa8/0x100
[c0000003f39679f0] [c000000000121a74] __local_bh_enable_ip+0x174/0x180
[c0000003f3967a60] [c000000000bf003c] _raw_spin_unlock_bh+0x5c/0x80
[c0000003f3967a90] [c000000000a8ac78] dev_deactivate_queue.constprop.28+0xc8/0x160
[c0000003f3967ad0] [c000000000a8c8b0] dev_deactivate_many+0xd0/0x520
[c0000003f3967b70] [c000000000a8cd40] dev_deactivate+0x40/0x60
[c0000003f3967ba0] [c000000000a5e0c4] linkwatch_do_dev+0x74/0xd0
[c0000003f3967bd0] [c000000000a5e694] __linkwatch_run_queue+0x1a4/0x1f0
[c0000003f3967c30] [c000000000a5e728] linkwatch_event+0x48/0x60
[c0000003f3967c50] [c0000000001444e8] process_one_work+0x238/0x710
[c0000003f3967d20] [c000000000144a48] worker_thread+0x88/0x4e0
[c0000003f3967db0] [c00000000014e3a8] kthread+0x178/0x1c0
[c0000003f3967e20] [c00000000000bfd0] ret_from_kernel_thread+0x5c/0x6c
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ibmvnic_reset can create and schedule a reset work item from
an IRQ context, so do not use a mutex, which can sleep. Convert
the reset work item mutex to a spin lock. Locking debugger generated
the trace output below.
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:908
in_atomic(): 1, irqs_disabled(): 1, pid: 120, name: kworker/8:1
4 locks held by kworker/8:1/120:
#0: 0000000017c05720 ((wq_completion)"events"){+.+.}, at: process_one_work+0x188/0x710
#1: 00000000ace90706 ((linkwatch_work).work){+.+.}, at: process_one_work+0x188/0x710
#2: 000000007632871f (rtnl_mutex){+.+.}, at: rtnl_lock+0x30/0x50
#3: 00000000fc36813a (&(&crq->lock)->rlock){..-.}, at: ibmvnic_tasklet+0x88/0x2010 [ibmvnic]
irq event stamp: 26293
hardirqs last enabled at (26292): [<c000000000122468>] tasklet_action_common.isra.12+0x78/0x1c0
hardirqs last disabled at (26293): [<c000000000befce8>] _raw_spin_lock_irqsave+0x48/0xf0
softirqs last enabled at (26288): [<c000000000a8ac78>] dev_deactivate_queue.constprop.28+0xc8/0x160
softirqs last disabled at (26289): [<c0000000000306e0>] call_do_softirq+0x14/0x24
CPU: 8 PID: 120 Comm: kworker/8:1 Kdump: loaded Not tainted 4.20.0-rc6 #6
Workqueue: events linkwatch_event
Call Trace:
[c0000003fffa7a50] [c000000000bc83e4] dump_stack+0xe8/0x164 (unreliable)
[c0000003fffa7aa0] [c00000000015ba0c] ___might_sleep+0x2dc/0x320
[c0000003fffa7b20] [c000000000be960c] __mutex_lock+0x8c/0xb40
[c0000003fffa7c30] [d000000006202ac8] ibmvnic_reset+0x78/0x330 [ibmvnic]
[c0000003fffa7cc0] [d0000000062097f4] ibmvnic_tasklet+0x1054/0x2010 [ibmvnic]
[c0000003fffa7e00] [c0000000001224c8] tasklet_action_common.isra.12+0xd8/0x1c0
[c0000003fffa7e60] [c000000000bf1238] __do_softirq+0x1a8/0x64c
[c0000003fffa7f90] [c0000000000306e0] call_do_softirq+0x14/0x24
[c0000003f3f87980] [c00000000001ba50] do_softirq_own_stack+0x60/0xb0
[c0000003f3f879c0] [c0000000001218a8] do_softirq+0xa8/0x100
[c0000003f3f879f0] [c000000000121a74] __local_bh_enable_ip+0x174/0x180
[c0000003f3f87a60] [c000000000bf003c] _raw_spin_unlock_bh+0x5c/0x80
[c0000003f3f87a90] [c000000000a8ac78] dev_deactivate_queue.constprop.28+0xc8/0x160
[c0000003f3f87ad0] [c000000000a8c8b0] dev_deactivate_many+0xd0/0x520
[c0000003f3f87b70] [c000000000a8cd40] dev_deactivate+0x40/0x60
[c0000003f3f87ba0] [c000000000a5e0c4] linkwatch_do_dev+0x74/0xd0
[c0000003f3f87bd0] [c000000000a5e694] __linkwatch_run_queue+0x1a4/0x1f0
[c0000003f3f87c30] [c000000000a5e728] linkwatch_event+0x48/0x60
[c0000003f3f87c50] [c0000000001444e8] process_one_work+0x238/0x710
[c0000003f3f87d20] [c000000000144a48] worker_thread+0x88/0x4e0
[c0000003f3f87db0] [c00000000014e3a8] kthread+0x178/0x1c0
[c0000003f3f87e20] [c00000000000bfd0] ret_from_kernel_thread+0x5c/0x6c
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit a5681e20b541 ("net/ibmnvic: Fix deadlock problem
in reset") made the change to hold the RTNL lock during
driver reset but still calls netdev_notify_peers, which
results in a deadlock. Instead, use call_netdevice_notifiers,
which is functionally the same except that it does not
take the RTNL lock again.
Fixes: a5681e20b541 ("net/ibmnvic: Fix deadlock problem in reset")
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During device reset, queue memory is not being updated to accommodate
changes in ring buffer sizes supported by backing hardware. Track
any differences in ring buffer sizes following the reset and update
queue memory when possible.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The wrong index is used when cleaning up RX buffer objects during release
of RX queues. Update to use the correct index counter.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes to use rtnl_lock only during a reset to avoid
deadlock that could occur when a thread operating close is holding
rtnl_lock and waiting for reset_lock acquired by another thread,
which is waiting for rtnl_lock in order to set the number of tx/rx
queues during a reset.
Also, we now setting the number of tx/rx queues during a soft reset
for failover or LPM events.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't request tag insertion when it isn't present in outgoing skb.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When choosing channel amounts and ring sizes, the maximums in the
ibmvnic driver are defined by the virtual i/o server management
partition. Even though they are defined as maximums, the client
driver may in fact successfully request resources that exceed
these limits, which are mostly dependent on a user's hardware
With this in mind, provide an ethtool flag that when enabled will
allow the user to request resources limited by driver-defined
maximums instead of limits defined by the management partition.
The driver will try to honor the user's request but may not allowed
by the management partition. In this case, the driver requests
as close as it can get to the desired amount until it succeeds.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
ibmvnic uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
ibmvnic_netpoll_controller() was completely wrong anyway,
as it was scheduling NAPI to service RX queues (instead of TX),
so I doubt netpoll ever worked on this driver.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Cc: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check the return codes of these functions and halt reset
in case of failure. The driver will remain in a dormant state
until the next reset event, when device initialization will be
re-attempted.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Print a string instead of the error code. Since there is a
possibility that the driver can recover, classify it as a
warning instead of an error.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When backing device firmware reports an error, it provides an
error ID, which is meant to be queried for more detailed error
information. Currently, however, an error ID is not provided by
the Virtual I/O server and there are not any plans to do so. For
now, it is always unfilled or zero, so request_error_information
will never be called. Remove it.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Testing has uncovered a failure case that is not handled properly. In the
event that a login fails and we are not able to recover on the spot, we
return 0 from do_reset, preventing any error recovery code from being
triggered. Additionally, the state is set to "probed" meaning that when we
are able to trigger the error recovery, the driver always comes up in the
probed state. To handle the case properly, we need to return a failure code
here and set the adapter state to the state that we entered the reset in
indicating the state that we would like to come out of the recovery reset
in.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During a device failover, there may be latency between the loss
of the current backing device and a notification from firmware that
a failover has occurred. This latency can result in a large amount of
error printouts as firmware returns outgoing traffic with a generic
error code. These are not necessarily errors in this case as the
firmware is busy swapping in a new backing adapter and is not ready
to send packets yet. This patch reclassifies those error codes as
warnings with an explanation that a failover may be pending. All
other return codes will be considered errors.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lots of easy overlapping changes in the confict
resolutions here.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In its current state, the driver will handle backing device
login in a loop for a certain number of retries while the
device returns a partial success, indicating that the driver
may need to try again using a smaller number of resources.
The variable it checks to continue retrying may change
over the course of operations, resulting in reallocation
of resources but exits without sending the login attempt.
Guard against this by introducing a boolean variable that
will retain the state indicating that the driver needs to
reattempt login with backing device firmware.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a recovery hard reset to handle reset failure as a result of
change of device context following a transport event, such as a
backing device failover or partition migration. These operations reset
the device context to its initial state. If this occurs during a reset,
any initialization commands are likely to fail with an invalid state
error as backing device firmware requests reinitialization.
When this happens, make one more attempt by performing a hard reset,
which frees any resources currently allocated and performs device
initialization. If a transport event occurs during a device reset, a
flag is set which will trigger a new hard reset following the
completionof the current reset event.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set device resetting state at the earliest possible point: as soon as a
reset is successfully scheduled. The reset state is toggled off when
all resets have been processed to completion.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of having one initialization routine for all cases, create
a separate, simpler function for standard initialization, such as during
device probe. Use the original initialization function to handle
device reset scenarios. The goal of this patch is to avoid having
a single, cluttered init function to handle all possible
scenarios.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If setting the link state is not successful, print a warning
with the resulting return code and return it to be handled
by the caller.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If device init is interrupted by a failover, set the init return
code so that it can be checked and handled appropriately by the
init routine.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check whether CRQ command is successful before awaiting a response
from the management partition. If the command was not successful, the
driver may hang waiting for a response that will never come.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce an "active" state for a IBM vNIC Command-Response Queue. A CRQ
is considered active once it has initialized or linked with its partner by
sending an initialization request and getting a successful response back
from the management partition. Until this has happened, do not allow CRQ
commands to be sent other than the initialization request.
This change will avoid a protocol error in case of a device transport
event occurring during a initialization. When the driver receives a
transport event notification indicating that the backing hardware
has changed and needs reinitialization, any further commands other
than the initialization handshake with the VIOS management partition
will result in an invalid state error. Instead of sending a command
that will be returned with an error, print a warning and return an
error that will be handled by the caller.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set adapter NAPI state as disabled if they are removed. This will allow
them to be enabled again if reallocated in case of a hard reset.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When enabling the sub-CRQ IRQ a previous update sent a H_EOI prior
to the enablement to clear any pending interrupts that may be present
across a partition migration. This fixed a firmware bug where a
migration could erroneously indicate that a H_EOI was pending.
The H_EOI should only be sent when enabling during a mobility
event though. Doing so at other time could wrong and can produce
extra driver output when IRQs are enabled when doing TX completion.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move initialization of statistics buffers from ibmvnic_init function
into ibmvnic_probe. In the current state, ibmvnic_init will be called
again during a device reset, resulting in the allocation of new
buffers without freeing the old ones.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is not necessary to disable interrupt lines here during a reset
to handle a non-fatal firmware error. Move that call within the code
block that handles the other cases that do require interrupts to be
disabled and re-enabled.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the firmware map fails for whatever reason, remember to free
up the memory after.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid using value stored in the login response buffer when
cleaning TX and RX buffer pools since these could be inconsistent
depending on the device state. Instead use the field in the driver's
private data that tracks the number of active pools.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to a firmware bug, the hypervisor can send an interrupt to a
transmit or receive queue just prior to a partition migration, not
allowing the device enough time to handle it and send an EOI. When
the partition migrates, the interrupt is lost but an "EOI-pending"
flag for the interrupt line is still set in firmware. No further
interrupts will be sent until that flag is cleared, effectively
freezing that queue. To workaround this, the driver will disable the
hardware interrupt and send an H_EOI signal prior to re-enabling it.
This will flush the pending EOI and allow the driver to continue
operation.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When attempting to change the driver parameters, such as the MTU
value or number of queues, do not call netdev_notify_peers().
Doing so will deadlock on the rtnl_lock.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a bug in handling the possible return codes from sending the
login CRQ. The current code treats any non-success return value,
minus failure to send the crq and a timeout waiting for a login response,
as a need to re-send the login CRQ. This can put the drive in an
infinite loop of trying to login when getting return values other
that a partial success such as a return code of aborted. For these
scenarios the login will not ever succeed at this point and the
driver would need to be reset again.
To resolve this loop trying to login is updated to only retry the
login if the driver gets a return code of a partial success. Other
return codes are treated as an error and the driver returns an error
from ibmvnic_login().
To avoid infinite looping in the partial success return cases, the
number of retries is capped at the maximum number of supported
queues. This value was chosen because the driver does a renegotiation
of capabilities which sets the number of queues possible and allows
the driver to attempt a login for possible value for the number
of queues supported.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "name" field of struct vnic_login_client_data is a char array of
undefined length. This should be written as "char name[]" so the compiler
can make better decisions about the field (for example, not assuming
it's a single character). This was noticed while trying to tighten the
CONFIG_FORTIFY_SOURCE checking.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When resetting the ibmvnic driver after a partition migration occurs
there is no requirement to do a reset of the main CRQ. The current
driver code does the required re-enable of the main CRQ, then does
a reset of the main CRQ later.
What we should be doing for a driver reset after a migration is to
re-enable the main CRQ, release all the sub-CRQs, and then allocate
new sub-CRQs after capability negotiation.
This patch updates the handling of mobility resets to do the proper
work and not reset the main CRQ. To do this the initialization/reset
of the main CRQ had to be moved out of the ibmvnic_init routine
and in to the ibmvnic_probe and do_reset routines.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a failover case for a non-redundant pseries VNIC
configuration that was not being handled properly. The current
implementation assumes that the driver will always have a redandant
device to communicate with following a failover notification. There
are cases, however, when a non-redundant configuration can receive
a failover request. If that happens, the driver should wait until
it receives a signal that the device is ready for operation.
The driver is agnostic of its backing hardware configuration,
so this fix necessarily affects all device failover management.
The driver needs to wait until it receives a signal that the device
is ready for resetting. A flag is introduced to track this intermediary
state where the driver is waiting for an active device.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some cases, if the driver is waiting for a reset following
a device parameter change, failure to schedule a reset can result
in a hang since a completion signal is never sent.
If the device configuration is being altered by a tool such
as ethtool or ifconfig, it could cause the console to hang
if the reset request does not get scheduled. Add some additional
error handling code to exit the wait_for_completion if there is
one in progress.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Thomas Falcon
Murilo Fossa Vicentini
David S. Miller
YueHaibing
Wen Yang
Juliet Kim
Michał Mirosław
Eric Dumazet
Thomas Falcon
John Allen
Nathan Fontenot
Kees Cook