| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
If interface is connected to switch port configured for DCB there are
TX timeouts when bringing up interface. Problem started appearing after
adding in i40e driver code mqprio hardware offload mode. In function
i40e_vsi_configure_bw_alloc was added resetting BW rate which should
be executing when mqprio qdisc is removed but was also when there was
no mqprio qdisc added and DCB was enabled. In this patch was added
additional check for DCB flag so now when DCB is enabled the correct
DCB configs from before mqprio patch are restored.
Signed-off-by: Martyna Szapar <martyna.szapar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114790 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch configures FEC setting in i40e_force_link_state().
For some reason setting this field was overlooked thus causing
25G link to be configured incorrectly.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Function call to i40e_prep_for_reset() is duplicated in
i40e_shutdown routine and gets called before
i40e_enable_mc_magic_wake() which blocks it from being executed
correctly on system reboot or shutdown because adminq is already
disabled by first i40e_prep_for_reset() call.
Two register write calls are also duplicated.
Signed-off-by: Sergey Nemov <sergey.nemov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
prog_attached of struct netdev_bpf should have been superseded
by simply setting prog_id long time ago, but we kept it around
to allow offloading drivers to communicate attachment mode (drv
vs hw). Subsequently drivers were also allowed to report back
attachment flags (prog_flags), and since nowadays only programs
attached will XDP_FLAGS_HW_MODE can get offloaded, we can tell
the attachment mode from the flags driver reports. Remove
prog_attached member.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Pass the extact struct from a tc qdisc add to the block bind function and,
in turn, to the setup_tc ndo of binding device via the tc_block_offload
struct. Pass this back to any block callback registrations to allow
netlink logging of fails in the bind process.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
-EOPNOTSUPP is the error value that should be reported if a flower
command is not supported by a driver. Fix it in couple of Intel drivers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
random_ether_addr is a #define for eth_random_addr which is
generally preferred in kernel code by ~3:1
Convert the uses of random_ether_addr to enable removing the #define
Miscellanea:
o Convert &vfmac[0] to equivalent vfmac and avoid unnecessary line wrap
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the ndo_xdp_flush call implementation i40e_xdp_flush
as no callers of ndo_xdp_flush are left.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
This patch fixes a hardware reset support in VF driver.
It is needed because when a hardware reset is detected
adapter->state is in __I40EVF_RESETTING state before
i40evf_reset_task is called. Without this patch
unloading VF driver after a hardware reset ends
with a system crash.
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds a recalculation of number of MSI-X
vectors for VMDq in the case where we have less
vectors available than we would want to reserve for
VMDq.
It fixes the issue where we recalculate vectors left
and vectors wanted but we didn't take into account
the reduced number of queue pairs per VSI.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fix warnings regarding restricted __be32 type usage by strictly
specifying the type of the ipv4 address being printed in the dev_err
statement.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The expectation of the ops VIRTCHNL_OP_ENABLE_QUEUES and
VIRTCHNL_OP_DISABLE_QUEUES is that the queue map sent by
the VF is taken into account when enabling/disabling
queues in the VF VSI. This patch makes sure that happens.
By breaking out the individual queue set up functions so
that they can be called directly from the i40e_virtchnl_pf.c
file, only the queues as specified by the queue bit map that
accompanies the enable/disable queues ops will be handled.
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This fixes at least 2 issues I have found with the UDP tunnel filter
configuration.
The first issue is the fact that the tunnels didn't have any sort of mutual
exclusion in place to prevent an update from racing with a user request to
add/remove a port. As such you could request to add and remove a port
before the port update code had a chance to respond which would result in a
very confusing result. To address it I have added 2 changes. First I added
the RTNL mutex wrapper around our updating of the pending, port, and
filter_index bits. Second I added logic so that we cannot use a port that
has a pending deletion since we need to free the space in hardware before
we can allow software to reuse it.
The second issue addressed is the fact that we were not recording the
actual filter index provided to us by the admin queue. As a result we were
deleting filters that were not associated with the actual filter we wanted
to delete. To fix that I added a filter_index member to the UDP port
tracking structure.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Recent versions of the Linux kernel now warn about incorrect parameter
definitions for function comments. Fix up several function comments to
correctly reflect the current function arguments. This cleans up the
warnings and helps ensure our documentation is accurate.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
After many years of having a ~30 line copyright and license header to our
source files, we are finally able to reduce that to one line with the
advent of the SPDX identifier.
Also caught a few files missing the SPDX license identifier, so fixed
them up.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver now acts upon the XDP_REDIRECT return action. Two new ndos
are implemented, ndo_xdp_xmit and ndo_xdp_flush.
XDP_REDIRECT action enables XDP program to redirect frames to other
netdevs.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When we suspend and resume, we need to clear and re-enable the interrupt
scheme. This was previously not done while holding the RTNL lock, which
could be problematic, because we are actually destroying and re-creating
queues.
Hold the RTNL lock for the entire sequence of preparing for reset, and
when resuming. This additionally protects the flags related to interrupt
scheme under RTNL lock so that their modification is properly threaded.
This is part of a larger effort to remove the need for cmpxchg64 in
i40e_set_priv_flags().
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The iWarp client flags are all potentially changed when the RTNL lock is
not held, so they should not be part of the pf->flags variable. Instead,
move them into the state field so that we can use atomic bit operations.
This is part of a larger effort to remove cmpxchg64 in
i40e_set_priv_flags()
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This flag is modified outside of the RTNL lock and thus should not be
part of the pf->flags variable.
Use a state bit instead, so that we can use atomic bit operations.
This is part of a larger effort to remove cmpxchg64 in
i40e_set_priv_flags()
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The two Flow Directory auto disable flags are used at run time to mark
when the flow director features needed to be disabled. Thus the flags
could change even when the RTNL lock is not held.
They also have some code constructions which really should be
test_and_set or test_and_clear using atomic bit operations.
Create new state fields to mark this, and stop including them in
pf->flags.
This is part of a larger effort to remove the need for cmpxchg64 in
i40e_set_priv_flags().
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This flag is modified during run time, possibly even when the RTNL lock
is not held. Additionally it has a few places which should be using
test_and_set or test_and_clear atomic bit operations.
Create a new state bit __I40E_UDP_SYNC_PENDING and use it instead of the
ole I40E_FLAG_UDP_FILTER_SYNC flag.
This is part of a larger effort to remove the need for using cmpxchg64
in i40e_set_priv_flags.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The I40E_FLAG_FILTER_SYNC flag is modified during run time possibly when
the RTNL lock is not held. Thus, it should not be part of pf->flags, and
instead should be using atomic bit operations in the pf->state field.
Create a __I40E_MACVLAN_SYNC_PENDING state bit, and use it instead of
the old I40E_FLAG_FILTER_SYNC flag.
This is part of a larger effort to remove the need for cmpxchg64 in
i40e_set_priv_flags().
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add the SPDX identifiers to all the Intel wired LAN driver files, as
outlined in Documentation/process/license-rules.rst.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During suspend client MSIx vectors are freed while they are still
in use causing a crash on entering S3.
Fix this calling client close before freeing up its MSIx vectors.
Also update the client MSIx vectors on resume before client
open is called.
Fixes commit b980c0634fe5 ("i40e: shutdown all IRQs and disable MSI-X
when suspended")
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When we re-enable ATR we need to restore the input set for TCPv4
filters, in order for ATR to function correctly. We already do this for
the normal case of re-enabling ATR when disabling ntuple support.
However, when re-enabling ATR after the last TCPv4 filter is removed (but
when ntuple support is still active), we did not restore the TCPv4
filter input set.
This can cause problems if the TCPv4 filters from FDir had changed the
input set, as ATR will no longer behave as expected.
When clearing the ATR auto-disable flag, make sure we restore the TCPv4
input set to avoid this.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
A future patch needs to expand on the logic for re-enabling ATR. Doing
so would cause some code to break the 80-character line limit.
To reduce the level of indentation, factor out helper functions for
re-enabling ATR and SB rules.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When hardware has trouble with a particular filter, we delete it from
the list. Unfortunately, we did not properly update the per-filter
statistic when doing so.
Create a helper function to handle this, and properly reduce the
necessary counter so that it tracks the number of active filters
properly.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We used to use the function i40e_vlan_rx_register as a way to hook
into the now defunct .ndo_vlan_rx_register netdev hook. This was
removed but we kept the function around because we still used it
internally to control enabling or disabling of VLAN stripping.
As pointed out in upstream review, VLAN stripping is only used in a
single location and the previous function is quite small, just inline
it into i40e_restore_vlan() rather than carrying the function
separately.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch introduces new ethtool private flag used for
forcing true link state. Function i40e_force_link_state that implements
this functionality was added, it sets phy_type = 0 in order to
work-around firmware's LESM. False positive error messages were
suppressed.
The ndo_open() should not succeed if there were issues with forcing link
state to be UP.
Added I40E_PHY_TYPES_BITMASK define with all phy types OR-ed together in
one bitmask. Added after phy type definition, so it will be hard to
forget to include new phy types to the bitmask.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch provides support to add or delete cloud filter for queue
channels created for ADq on VF.
We are using the HW's cloud filter feature and programming it to act
as a TC filter applied to a group of queues.
There are two possible modes for a VF when applying a cloud filter
1. Basic Mode: Intended to apply filters that don't need a VF to be
Trusted. This would include the following
Dest MAC + L4 port
Dest MAC + VLAN + L4 port
2. Advanced Mode: This mode is only for filters with combination that
requires VF to be Trusted.
Dest IP + L4 port
When cloud filters are applied on a trusted VF and for some reason
the same VF is later made as untrusted then all cloud filters
will be deleted. All cloud filters has to be re-applied in
such a case.
Cloud filters are also deleted when queue channel is deleted.
Testing-Hints:
=============
1. Adding Basic Mode filter should be possible on a VF in
Non-Trusted mode.
2. In Advanced mode all filters should be able to be created.
Steps:
======
1. Enable ADq and create TCs using TC mqprio command
2. Apply cloud filter.
3. Turn-off the spoof check.
4. Pass traffic.
Example:
========
1. tc qdisc add dev enp4s2 root mqprio num_tc 4 map 0 0 0 0 1 2 2 3\
queues 2@0 2@2 1@4 1@5 hw 1 mode channel
2. tc qdisc add dev enp4s2 ingress
3. ethtool -K enp4s2 hw-tc-offload on
4. ip link set ens261f0 vf 0 spoofchk off
5. tc filter add dev enp4s2 protocol ip parent ffff: prio 1 flower\
dst_ip 192.168.3.5/32 ip_proto udp dst_port 25 skip_sw hw_tc 2
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The MAC, FW Version and NPAR check used to determine
if shutting off the FW LLDP engine is supported is not
using the usual feature check mechanism.
This patch fixes the problem by moving the feature check
to i40e_sw_init in order to set a flag in pf->hw_features
that ethtool will use for priv_flags disable operation.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Broadcast filters can now cause overflow promiscuous to trigger when
adding "too many" VLANs to all the ports of a device and the driver
needs a way to exit overflow promiscuous once triggered.
Currently the driver looks to see if there are "too many" filters and/or
we have any failed filters to determine when it is safe to exit overflow
promiscuous. If we trigger overflow promiscuous with broadcast filters,
any new filters added will be "auto-failed" until we exit overflow
promiscuous. Since the user can't manually remove the failed broadcast
filters for VLANs (nor should we expect the user to do such), there is
no way to exit overflow promiscuous without reloading the driver.
The easiest way to do this is to remove the shortcut to "auto-fail"
filters in overflow promiscuous. If the user removes the VLANs, the
failed filters will be removed and since we're no longer "auto-failing"
new filters, we'll eventually get a good set of filters and exit
overflow promiscuous.
This has the side benefit of making filter state more explicit in that
if a filter says it's failed we know for a fact it failed and not just
assuming it will if we're in overflow promiscuous. This is nice because
if the user removes some filters and then adds some, even if we're in
overflow promiscuous, the filter might succeed; we were just assuming it
won't because the user hasn't rectified other existing failed filters.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This code here is quite complex and easy to screw up. Let's see if we
can't improve the readability and maintainability a bit. This refactors
out promisc_changed into two variables 'old_overflow' and 'new_overflow'
which makes it a bit clearer when we're concerned about when and how
overflow promiscuous is changed. This also makes so that we no longer
need to pass a boolean pointer to i40e_aqc_add_filters. Instead we can
simply check if we changed the overflow promiscuous flag since the
function start.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When adding a bunch of VLANs to all the ports on a device, it's possible
to run out of space for broadcast filters. The driver should trigger
overflow promiscuous in this circumstance to prevent traffic from being
unexpectedly dropped.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Could a Bad Person do Bad Things to a server if they found these
addresses printed in the log? Who knows? But let's not take that risk.
Remove pointers from a bunch of printks. In some cases, I was able to
adjust the message to indicate whether or not the value was null. In
others, I just removed the entire message as there was really no hope of
saving it.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fixes the following sparse warning:
drivers/net/ethernet/intel/i40e/i40e_main.c:5440:5: warning:
symbol 'i40e_get_link_speed' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch replaces the existing mechanism for determining the correct
value to program for adaptive ITR with yet another new and more
complicated approach.
The basic idea from a 30K foot view is that this new approach will push the
Rx interrupt moderation up so that by default it starts in low latency and
is gradually pushed up into a higher latency setup as long as doing so
increases the number of packets processed, if the number of packets drops
to 4 to 1 per packet we will reset and just base our ITR on the size of the
packets being received. For Tx we leave it floating at a high interrupt
delay and do not pull it down unless we start processing more than 112
packets per interrupt. If we start exceeding that we will cut our interrupt
rates in half until we are back below 112.
The side effect of these patches are that we will be processing more
packets per interrupt. This is both a good and a bad thing as it means we
will not be blocking processing in the case of things like pktgen and XDP,
but we will also be consuming a bit more CPU in the cases of things such as
network throughput tests using netperf.
One delta from this versus the ixgbe version of the changes is that I have
made the interrupt moderation a bit more aggressive when we are in bulk
mode by moving our "goldilocks zone" up from 48 to 96 to 56 to 112. The
main motivation behind moving this is to address the fact that we need to
update less frequently, and have more fine grained control due to the
separate Tx and Rx ITR times.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch is mostly prep-work for replacing the current approach to
programming the dynamic aka adaptive ITR. Specifically here what we are
doing is splitting the Tx and Rx ITR each into two separate values.
The first value current_itr represents the current value of the register.
The second value target_itr represents the desired value of the register.
The general plan by doing this is to allow for deferring the update of the
ITR value under certain circumstances. For now we will work with what we
have, but in the future I hope to change the behavior so that we always
only update one ITR at a time using some simple logic to determine which
ITR requires an update.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds necessary delay for 4.33 firmware to recover after
EMP reset. Without this patch driver occasionally reinitializes
structures too quickly to communicate with firmware after EMP reset
causing AdminQ to timeout.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The rings are already split out into Tx and Rx rings so it doesn't make
sense to have any single ring store both a Tx and Rx itr_setting value.
Since that is the case drop the pair in favor of storing just a single ITR
value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fix the number of queues per enabled TC and report available queues
to the kernel without having to limit them to the max RSS limit so
they are available to be mapped for XPS. This allows a queue per
processing thread available for handling traffic for the given
traffic class.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch suppresses the message about invalid TC mapping and wrong
selected TX queue. The root cause of this bug was setting too many
TC queue pairs on huge multiprocessor machines. When quantity of the
TC queue pairs is exceeding MSI-X vectors count then TX queue number
can be selected beyond actual TX queues amount.
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The drivers for i40e and i40evf had a reg_idx value stored in the q_vector
that was going completely unused. I can only assume this was copied over
from ixgbe and nobody knew how to use it.
I'm going to make use of the value to avoid having to compute the vector
and thus the register index for multiple paths throughout the drivers.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When implementing support for IP_USER_FLOW filters, we correctly
programmed a filter for both the non fragmented IPv4/Other filter, as
well as the fragmented IPv4 filters. However, we did not properly
program the input set for fragmented IPv4 PCTYPE. This meant that the
filters would almost certainly not match, unless the user specified all
of the flow types.
Add support to program the fragmented IPv4 filter input set. Since we
always program these filters together, we'll assume that the two input
sets must match, and will thus always program the input sets to the same
value.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
kdump fails in the system when used in conjunction with Ethernet driver
X722/X710. This is mainly because when we are resource constrained i.e.
when we have just one online_cpus, we are enabling VMDq and iWARP. It
doesn't make sense to enable them with just one CPU and starve kdump
for lack of IRQs.
So don't enable VMDq or iWARP when we just have a single CPU.
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Using ethtool --set-priv-flags disable-fw-lldp <on/off> is persistent
across reboots/reloads so we need some mechanism in the driver to detect
if it's on or off on init so we can set the ethtool private flag
appropriately. Without this, every time the driver is reloaded the flag
will default to off regardless of whether it's on or off in FW.
We detect this by first attempting to program DCB and if AQ fails
returning I40E_AQ_RC_EPERM, we know that LLDP is disabled in FW.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Implement the private flag disable-fw-lldp for ethtool
to disable the processing of LLDP packets by the FW.
This will stop the FW from consuming LLDPDU and cause
them to be sent up the stack.
The FW is also being configured to apply a default DCB
configuration on link up.
Toggling the value of this flag will also cause a PF reset.
Disabling FW DCB will also disable DCBx.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Make use of tc_cls_can_offload_and_chain0() to set extack msg in case
ethtool tc offload flag is not set or chain unsupported.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Martyna Szapar
Gustavo A. R. Silva
Mariusz Stachura
Sergey Nemov
Jakub Kicinski
John Hurley
Jiri Pirko
Joe Perches
Jesper Dangaard Brouer
Paweł Jabłoński
Patryk Małek
Jacob Keller
Harshitha Ramamurthy
Alexander Duyck
Jeff Kirsher
Björn Töpel
Shiraz Saleem
Avinash Dayanand
Dave Ertman
Alan Brady
Mitch Williams
Wei Yongjun
Filip Sadowski
Amritha Nambiar
David S. Miller