| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Post VF initialization, there are a couple of different ways in which a
VF reset can be triggered. One is when the underlying PF itself goes
through a reset and other is via a VFLR interrupt. ice_reset_vf introduced
in this patch handles both these cases.
Also introduced in this patch is a helper function ice_aq_send_msg_to_vf
to send messages to VF over the mailbox queue. The PF uses this to send
reset notifications to VFs.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch implements parts of ice_sriov_configure and VF reset flow.
To create virtual functions (VFs), the user sets a value in num_vfs
through sysfs. This results in the kernel calling the handler for
.sriov_configure which is ice_sriov_configure.
VF setup first starts with a VF reset, followed by allocation of the VF
VSI using ice_vf_vsi_setup. Once the VF setup is complete a state bit
ICE_VF_STATE_INIT is set in the vf->states bitmap to indicate that
the VF is ready to go.
Also for VF reset to go into effect, it's necessary to issue a disable
queue command (ice_aqc_opc_dis_txqs). So this patch updates multiple
functions in the disable queue flow to take additional parameters that
distinguish if queues are being disabled due to VF reset.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The functions that are used for PF VSI/netdev setup will also be used
for SR-IOV support. To allow reuse of these functions, move these
functions out of ice_main.c to ice_common.c/ice_lib.c
This move is done across multiple patches. Each patch moves a few
functions and may have minor adjustments. For example, a function that was
previously static in ice_main.c will be made non-static temporarily in
its new location to allow the driver to build cleanly. These adjustments
will be removed in subsequent patches where more code is moved out of
ice_main.c
In this particular patch, the following functions were moved out of
ice_main.c:
int ice_add_mac_to_list
ice_free_fltr_list
ice_stat_update40
ice_stat_update32
ice_update_eth_stats
ice_vsi_add_vlan
ice_vsi_kill_vlan
ice_vsi_manage_vlan_insertion
ice_vsi_manage_vlan_stripping
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch implements a watchdog task to get packet statistics from
the device.
This patch also adds support for the following ethtool operations:
ethtool devname
ethtool -s devname [msglvl N] [msglevel type on|off]
ethtool -g|--show-ring devname
ethtool -G|--set-ring devname [rx N] [tx N]
ethtool -i|--driver devname
ethtool -d|--register-dump devname [raw on|off] [hex on|off] [file name]
ethtool -k|--show-features|--show-offload devname
ethtool -K|--features|--offload devname feature on|off
ethtool -P|--show-permaddr devname
ethtool -S|--statistics devname
ethtool -a|--show-pause devname
ethtool -A|--pause devname [autoneg on|off] [rx on|off] [tx on|off]
ethtool -r|--negotiate devname
CC: Andrew Lunn <andrew@lunn.ch>
CC: Jakub Kicinski <kubakici@wp.pl>
CC: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch configures the VSIs to be able to send and receive
packets by doing the following:
1) Initialize flexible parser to extract and include certain
fields in the Rx descriptor.
2) Add Tx queues by programming the Tx queue context (implemented in
ice_vsi_cfg_txqs). Note that adding the queues also enables (starts)
the queues.
3) Add Rx queues by programming Rx queue context (implemented in
ice_vsi_cfg_rxqs). Note that this only adds queues but doesn't start
them. The rings will be started by calling ice_vsi_start_rx_rings on
interface up.
4) Configure interrupts for VSI queues.
5) Implement ice_open and ice_stop.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds to the initialization flow by getting switch
configuration, scheduler configuration and device capabilities.
Switch configuration:
On boot, an L2 switch element is created in the firmware per physical
function. Each physical function is also mapped to a port, to which its
switch element is connected. In other words, this switch can be visualized
as an embedded vSwitch that can connect a physical function's virtual
station interfaces (VSIs) to the egress/ingress port. Egress/ingress
filters will be eventually created and applied on this switch element.
As part of the initialization flow, the driver gets configuration data
from this switch element and stores it.
Scheduler configuration:
The Tx scheduler is a subsystem responsible for setting and enforcing QoS.
As part of the initialization flow, the driver queries and stores the
default scheduler configuration for the given physical function.
Device capabilities:
As part of initialization, the driver has to determine what the device is
capable of (ex. max queues, VSIs, etc). This information is obtained from
the firmware and stored by the driver.
CC: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch implements multiple pieces of the initialization flow
as follows:
1) A reset is issued to ensure a clean device state, followed
by initialization of admin queue interface.
2) Once the admin queue interface is up, clear the PF config
and transition the device to non-PXE mode.
3) Get the NVM configuration stored in the device's non-volatile
memory (NVM) using ice_init_nvm.
CC: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
A control queue is a hardware interface which is used by the driver
to interact with other subsystems (like firmware, PHY, etc.). It is
implemented as a producer-consumer ring. More specifically, an
"admin queue" is a type of control queue used to interact with the
firmware.
This patch introduces data structures and functions to initialize
and teardown control/admin queues. Once the admin queue is initialized,
the driver uses it to get the firmware version.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds a basic driver framework for the Intel(R) E800 Ethernet
Series of network devices. There is no functionality right now other than
the ability to load.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
Anirudh Venkataramanan