Age | Commit message (Collapse) | Author | Files | Lines |
|
We set controller to drop control frames and not trying
to pass them on. This is only needed for debug reasons.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to set tx_skb pointer before send frame.
If we receive interrupt before we set pointer we will try
to free SKB with wrong pointer.
Now we are sure that SKB pointer will never be NULL during
handling TX done and check is removed.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When interrupt is received we read directly from control
register for RX/TX instead of reading cause register
since this register fails to indicate TX done when
TX interrupt is "edge mode".
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do WARN_ON_ONCE instead of WARN_ON in gue_gro_receive when the offload
callcaks are bad (either don't exist or gro_receive is not specified).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add calls to gro_cells infrastructure to do GRO when receiving on a tunnel.
Testing:
Ran 200 netperf TCP_STREAM instance
- With fix (GRO enabled on VXLAN interface)
Verify GRO is happening.
9084 MBps tput
3.44% CPU utilization
- Without fix (GRO disabled on VXLAN interface)
Verified no GRO is happening.
9084 MBps tput
5.54% CPU utilization
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The remote checksum offload GRO did not consider the case that frag0
might be in use. This patch fixes that by accessing headers using the
skb_gro functions and not saving offsets relative to skb->head.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If you simply load and unload the module without starting the interfaces,
the queues are never created and you get a bad pointer dereference.
Signed-off-by: Chas Williams <3chas3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current Secure port mode requires the port-based VLANs to also be
valid in the 802.1Q VLAN Table Unit. The current hardware bridging
support only configures the port-based VLANs, thus is broken.
A new patchset is required to adapt the hardware bridging code to fully
support the Secure port mode.
In the meantime, change the 802.1Q mode of every ports to Fallback,
which filtering is more permissive, and doesn't add this restriction to
handle port-based and tagged-based VLANs.
Fixes: 8efdda4a1b60 ("net: dsa: mv88e6xxx: use port 802.1Q mode Secure")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
err_out_vnic_unregister is used regardless of whether
SRIOV is enabled or not.
Reported-by: Jesse Brandeburg <jesse.brangeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow specification of per route IP tunnel instructions also for IPv6.
This complements commit 3093fbe7ff4b ("route: Per route IP tunnel metadata
via lightweight tunnel").
Signed-off-by: Jiri Benc <jbenc@redhat.com>
CC: YOSHIFUJI Hideaki <hideaki.yoshifuji@miraclelinux.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use flowi_tunnel in flowi6 similarly to what is done with IPv4.
This complements commit 1b7179d3adff ("route: Extend flow representation
with tunnel key").
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support metadata based (formerly flow based) tunneling also for IPv6.
This complements commit ee122c79d422 ("vxlan: Flow based tunneling").
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 'flags' variable is already defined in the outer scope.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If output device wants to see the dst, inherit the dst of the original skb
in the ndisc request.
This is an IPv6 counterpart of commit 0accfc268f4d ("arp: Inherit metadata
dst when creating ARP requests").
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The fix in commit 48fb6b554501 is incomplete, as now ip6_route_input can be
called with non-NULL dst if it's a metadata dst and the reference is leaked.
Drop the reference.
Fixes: 48fb6b554501 ("ipv6: fix crash over flow-based vxlan device")
Fixes: ee122c79d422 ("vxlan: Flow based tunneling")
CC: Wei-Chun Chao <weichunc@plumgrid.com>
CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the lwtunnel state resides in per-protocol data. This is
a problem if we encapsulate ipv6 traffic in an ipv4 tunnel (or vice versa).
The xmit function of the tunnel does not know whether the packet has been
routed to it by ipv4 or ipv6, yet it needs the lwtstate data. Moving the
lwtstate data to dst_entry makes such inter-protocol tunneling possible.
As a bonus, this brings a nice diffstat.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename the ipv4_tos and ipv4_ttl fields to just 'tos' and 'ttl', as they'll
be used with IPv6 tunnels, too.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the IPv6 addresses as an union with IPv4 ones. When using IPv4, the
newly introduced padding after the IPv4 addresses needs to be zeroed out.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ip_tunnels.h include file uses mixture of __u16 and u16 (etc.) types.
Unify it to the non-underscore variants.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The custom alignment of struct ip_tunnel_key is unnecessary. In struct
sw_flow_key, it starts at offset 256, in struct ip_tunnel_info it's the
first field.
The structure is also packed even without the __packed keyword.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert the xgene_get_mac_address to device_get_mac_address(), and
xgene_get_phy_mode() to device_get_phy_mode().
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Andreas reported breakage adding routes with local nexthops:
$ ip route show table main
...
172.28.0.0/24 dev vnf-xe1p0 proto kernel scope link src 172.28.0.16
$ ip route add 10.0.0.0/8 via 172.28.0.32 table 100 dev vnf-xe1p0
RTNETLINK answers: Resource temporarily unavailable
3bfd847203c changed the lookup to use the passed in table but for cases like
this the nexthop is in the local table rather than the passed in table.
Fixes: 3bfd847203c ("net: Use passed in table for nexthop lookups")
Reported-by: Andreas Schultz <aschultz@tpip.net>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
.maxtype should match .policy. Probably just been getting lucky here
because IFLA_BRPORT_MAX > IFLA_BR_MAX.
Fixes: 13323516 ("bridge: implement rtnl_link_ops->changelink")
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dev==NULL check in smsc911x_probe_config is useless
and isn't providing any additional protection. If a fwnode
doesn't exist then an appropriate error should be returned
by device_get_phy_mode() covering the original case
of a missing of/fwnode.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds MAC address length check back into
the device_get_mac_addr() function before calling
is_valid_ether_addr() similar to the way the OF
routine does it.
Update the comments for the two new functions.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make fib_encap_match() static as it isn't used outside the file.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since all users are now converted to the inline implementation,
remove the out-of-line implementation entirely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of using the out-of-line EWMA calculation, use DECLARE_EWMA()
to create static inlines. On x86/64 this results in code that's one
byte larger (for me), but reduces struct link_ant and struct link
size by the two unsigned long values that store the parameters each.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reduces code size slightly (at least on x86/64) while also
removing memory consumption by two unsigned long values for each
ath5k device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of using the out-of-line EWMA calculation, use DECLARE_EWMA()
to create static inlines. On x86/64 this results in no change in code
size for me, but reduces the struct receive_queue size by the two
unsigned long values that store the parameters.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit f34fa14cc033 ("bnx2x: Add vxlan RSS support") has introduced an
endianity issue when passing the vxlan UDP port to the HW.
Reported-by: <fengguang.wu@intel.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When ndo_add|del_slave ops are used, they're taken from the respective
master device's netdev ops, so if the master device is a VRF only then
the VRF ops will get called thus no need to check the type of the
master.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can simplify do_vrf_add_slave by moving vrf_insert_slave in the end
of the enslaving and thus eliminate an error goto label. It always
succeeds and isn't needed before that anyway.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The upper/lower functions already check for duplicate slaves so no need
to do it again.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's pointless to panic on cache create failure when that case is handled
and even more so since it's not a kernel-wide fatal problem so don't
panic.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently whenever a packet different from ETH_P_IP is sent through the
VRF device it is leaked so plug the leaks and properly drop these
packets.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit feb44f1f7a4ac299d1ab1c3606860e70b9b89d69 (x86/xen:
Provide a "Xen PV" APIC driver to support >255 VCPUs) Xen guests need
a full APIC driver and thus should depend on X86_LOCAL_APIC.
This fixes an i386 build failure with !SMP && !CONFIG_X86_UP_APIC by
disabling Xen support in this configuration.
Users needing Xen support in a non-SMP i386 kernel will need to enable
CONFIG_X86_UP_APIC.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: <stable@vger.kernel.org>
|
|
While running net-next I hit this:
[ 634.073119] ===============================
[ 634.073150] [ INFO: suspicious RCU usage. ]
[ 634.073182] 4.2.0-rc6+ #45 Not tainted
[ 634.073213] -------------------------------
[ 634.073244] include/net/vrf.h:38 suspicious rcu_dereference_check()
usage!
[ 634.073274]
other info that might help us debug this:
[ 634.073307]
rcu_scheduler_active = 1, debug_locks = 1
[ 634.073338] 2 locks held by swapper/0/0:
[ 634.073369] #0: (((&n->timer))){+.-...}, at: [<ffffffff8112bc35>]
call_timer_fn+0x5/0x480
[ 634.073412] #1: (slock-AF_INET){+.-...}, at: [<ffffffff8174f0f5>]
icmp_send+0x155/0x5f0
[ 634.073450]
stack backtrace:
[ 634.073483] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.2.0-rc6+ #45
[ 634.073514] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS
VirtualBox 12/01/2006
[ 634.073545] 0000000000000000 0593ba8242d9ace4 ffff88002fc03b48
ffffffff81803f1b
[ 634.073612] 0000000000000000 ffffffff81e12500 ffff88002fc03b78
ffffffff811003c5
[ 634.073642] 0000000000000000 ffff88002ec4e600 ffffffff81f00f80
ffff88002fc03cf0
[ 634.073669] Call Trace:
[ 634.073694] <IRQ> [<ffffffff81803f1b>] dump_stack+0x4c/0x65
[ 634.073728] [<ffffffff811003c5>] lockdep_rcu_suspicious+0xc5/0x100
[ 634.073763] [<ffffffff8174eb56>] icmp_route_lookup+0x176/0x5c0
[ 634.073793] [<ffffffff8174f2fb>] ? icmp_send+0x35b/0x5f0
[ 634.073818] [<ffffffff8174f274>] ? icmp_send+0x2d4/0x5f0
[ 634.073844] [<ffffffff8174f3ce>] icmp_send+0x42e/0x5f0
[ 634.073873] [<ffffffff8170b662>] ipv4_link_failure+0x22/0xa0
[ 634.073899] [<ffffffff8174bdda>] arp_error_report+0x3a/0x80
[ 634.073926] [<ffffffff816d6100>] ? neigh_lookup+0x2c0/0x2c0
[ 634.073952] [<ffffffff816d396e>] neigh_invalidate+0x8e/0x110
[ 634.073984] [<ffffffff816d62ae>] neigh_timer_handler+0x1ae/0x290
[ 634.074013] [<ffffffff816d6100>] ? neigh_lookup+0x2c0/0x2c0
[ 634.074013] [<ffffffff8112bce3>] call_timer_fn+0xb3/0x480
[ 634.074013] [<ffffffff8112bc35>] ? call_timer_fn+0x5/0x480
[ 634.074013] [<ffffffff816d6100>] ? neigh_lookup+0x2c0/0x2c0
[ 634.074013] [<ffffffff8112c2bc>] run_timer_softirq+0x20c/0x430
[ 634.074013] [<ffffffff810af50e>] __do_softirq+0xde/0x630
[ 634.074013] [<ffffffff810afc97>] irq_exit+0x117/0x120
[ 634.074013] [<ffffffff81810976>] smp_apic_timer_interrupt+0x46/0x60
[ 634.074013] [<ffffffff8180e950>] apic_timer_interrupt+0x70/0x80
[ 634.074013] <EOI> [<ffffffff8106b9d6>] ? native_safe_halt+0x6/0x10
[ 634.074013] [<ffffffff81101d8d>] ? trace_hardirqs_on+0xd/0x10
[ 634.074013] [<ffffffff81027d43>] default_idle+0x23/0x200
[ 634.074013] [<ffffffff8102852f>] arch_cpu_idle+0xf/0x20
[ 634.074013] [<ffffffff810f89ba>] default_idle_call+0x2a/0x40
[ 634.074013] [<ffffffff810f8dcc>] cpu_startup_entry+0x39c/0x4c0
[ 634.074013] [<ffffffff817f9cad>] rest_init+0x13d/0x150
[ 634.074013] [<ffffffff81f69038>] start_kernel+0x4a8/0x4c9
[ 634.074013] [<ffffffff81f68120>] ?
early_idt_handler_array+0x120/0x120
[ 634.074013] [<ffffffff81f68339>] x86_64_start_reservations+0x2a/0x2c
[ 634.074013] [<ffffffff81f68485>] x86_64_start_kernel+0x14a/0x16d
It would seem vrf_master_ifindex_rcu() can be called without RCU held in
other contexts as well so introduce a new helper which acquires rcu and
returns the ifindex.
Also add curly braces around both the "if" and "else" parts as per the
style guide.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When CONFIG_LWTUNNEL config is not enabled, the lwtstate_free() is not
declared in lwtunnel.h at all. However, even in this case, the function
is still referenced in fib_semantics.c so that there appears the
following sparse warnings:
net/ipv4/fib_semantics.c:553:17: error: undefined identifier 'lwtstate_free'
CC net/ipv4/fib_semantics.o
net/ipv4/fib_semantics.c: In function ‘fib_encap_match’:
net/ipv4/fib_semantics.c:553:3: error: implicit declaration of function ‘lwtstate_free’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[1]: *** [net/ipv4/fib_semantics.o] Error 1
make: *** [net/ipv4/fib_semantics.o] Error 2
To eliminate the error, we define an empty function for lwtstate_free()
in lwtunnel.h when CONFIG_LWTUNNEL is disabled.
Fixes: df383e6240ef ("lwtunnel: fix memory leak")
Cc: Jiri Benc <jbenc@redhat.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tested with W541 and Ultra Dock 170w
Signed-off-by: Rick Sherman <rick@shermdog.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The fix for deadlock in PM in commit [1ee23fe07ee8: ALSA: usb-audio:
Fix deadlocks at resuming] introduced a new check of in_pm flag.
However, the brainless patch author evaluated it in a wrong way
(logical AND instead of logical OR), thus usb_autopm_get_interface()
is wrongly called at probing, leading to unbalance of runtime PM
refcount.
This patch fixes it by correcting the logic.
Reported-by: Hans Yang <hansy@nvidia.com>
Fixes: 1ee23fe07ee8 ('ALSA: usb-audio: Fix deadlocks at resuming')
Cc: <stable@vger.kernel.org> [v3.15+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
make payload expression aware of the fact that VLAN offload may have
removed a vlan header.
When we encounter tagged skb, transparently insert the tag into the
register so that vlan header matching can work without userspace being
aware of offload features.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
REPORT LUNS should not fail just because the allocation length is less
than 16. The relevant section of SPC-4 is:
4.2.5.6 Allocation length
The ALLOCATION LENGTH field specifies the maximum number of bytes or
blocks that an application client has allocated in the Data-In
Buffer. The ALLOCATION LENGTH field specifies bytes unless a
different requirement is stated in the command definition.
An allocation length of zero specifies that no data shall be
transferred. This condition shall not be considered an error.
So we should just truncate our response rather than return an error.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Spencer Baugh <sbaugh@catern.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
We can drop the check because if vrf_ptr is present then we must have
the vrf device as a master and since we're running with rtnl it can't go
away.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dstats and rth are always present because we fail the device registration
if they can't be allocated in vrf_init() (ndo_init) so drop the unnecessary
checks.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
slave_queue has a num_slaves member which is unused, drop it.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netdev_master_upper_dev_link/unlink already do a dev_hold/put on the
devices being linked, so no need to take another reference.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Passes static analysis by Smatch.
Signed-off-by: Andrew Schwartzmeyer <andschwa@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|