| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull networking updates from David Miller:
1) BBR TCP congestion control, from Neal Cardwell, Yuchung Cheng and
co. at Google. https://lwn.net/Articles/701165/
2) Do TCP Small Queues for retransmits, from Eric Dumazet.
3) Support collect_md mode for all IPV4 and IPV6 tunnels, from Alexei
Starovoitov.
4) Allow cls_flower to classify packets in ip tunnels, from Amir Vadai.
5) Support DSA tagging in older mv88e6xxx switches, from Andrew Lunn.
6) Support GMAC protocol in iwlwifi mwm, from Ayala Beker.
7) Support ndo_poll_controller in mlx5, from Calvin Owens.
8) Move VRF processing to an output hook and allow l3mdev to be
loopback, from David Ahern.
9) Support SOCK_DESTROY for UDP sockets. Also from David Ahern.
10) Congestion control in RXRPC, from David Howells.
11) Support geneve RX offload in ixgbe, from Emil Tantilov.
12) When hitting pressure for new incoming TCP data SKBs, perform a
partial rathern than a full purge of the OFO queue (which could be
huge). From Eric Dumazet.
13) Convert XFRM state and policy lookups to RCU, from Florian Westphal.
14) Support RX network flow classification to igb, from Gangfeng Huang.
15) Hardware offloading of eBPF in nfp driver, from Jakub Kicinski.
16) New skbmod packet action, from Jamal Hadi Salim.
17) Remove some inefficiencies in snmp proc output, from Jia He.
18) Add FIB notifications to properly propagate route changes to
hardware which is doing forwarding offloading. From Jiri Pirko.
19) New dsa driver for qca8xxx chips, from John Crispin.
20) Implement RFC7559 ipv6 router solicitation backoff, from Maciej
Żenczykowski.
21) Add L3 mode to ipvlan, from Mahesh Bandewar.
22) Support 802.1ad in mlx4, from Moshe Shemesh.
23) Support hardware LRO in mediatek driver, from Nelson Chang.
24) Add TC offloading to mlx5, from Or Gerlitz.
25) Convert various drivers to ethtool ksettings interfaces, from
Philippe Reynes.
26) TX max rate limiting for cxgb4, from Rahul Lakkireddy.
27) NAPI support for ath10k, from Rajkumar Manoharan.
28) Support XDP in mlx5, from Rana Shahout and Saeed Mahameed.
29) UDP replicast support in TIPC, from Richard Alpe.
30) Per-queue statistics for qed driver, from Sudarsana Reddy Kalluru.
31) Support BQL in thunderx driver, from Sunil Goutham.
32) TSO support in alx driver, from Tobias Regnery.
33) Add stream parser engine and use it in kcm.
34) Support async DHCP replies in ipconfig module, from Uwe
Kleine-König.
35) DSA port fast aging for mv88e6xxx driver, from Vivien Didelot.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1715 commits)
mlxsw: switchx2: Fix misuse of hard_header_len
mlxsw: spectrum: Fix misuse of hard_header_len
net/faraday: Stop NCSI device on shutdown
net/ncsi: Introduce ncsi_stop_dev()
net/ncsi: Rework the channel monitoring
net/ncsi: Allow to extend NCSI request properties
net/ncsi: Rework request index allocation
net/ncsi: Don't probe on the reserved channel ID (0x1f)
net/ncsi: Introduce NCSI_RESERVED_CHANNEL
net/ncsi: Avoid unused-value build warning from ia64-linux-gcc
net: Add netdev all_adj_list refcnt propagation to fix panic
net: phy: Add Edge-rate driver for Microsemi PHYs.
vmxnet3: Wake queue from reset work
i40e: avoid NULL pointer dereference and recursive errors on early PCI error
qed: Add RoCE ll2 & GSI support
qed: Add support for memory registeration verbs
qed: Add support for QP verbs
qed: PD,PKEY and CQ verb support
qed: Add support for RoCE hw init
qede: Add qedr framework
...
|
|
We get 2 warnings when building kernel with W=1:
drivers/net/ethernet/marvell/mvneta.c:639:27: warning: no previous prototype for 'mvneta_get_stats64' [-Wmissing-prototypes]
drivers/net/ethernet/marvell/mvneta.c:3529:5: warning: no previous prototype for 'mvneta_ethtool_set_link_ksettings' [-Wmissing-prototypes]
In fact, these two functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: netdev@vger.kernel.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160818125731.27256-9-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The ethtool api {get|set}_settings is deprecated.
We move the mvneta driver to new api {get|set}_link_ksettings.
We use the generic function phy_ethtool_get_link_ksettings,
and update old mvneta_ethtool_set_settings to the new api.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy_dev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit aebea2ba0f74 ("net: mvneta: fix Tx interrupt delay") intended to
set coalescing threshold to a value guaranteeing interrupt generation
per each sent packet, so that buffers can be released with no delay.
In fact setting threshold to '1' was wrong, because it causes interrupt
every two packets. According to the documentation a reason behind it is
following - interrupt occurs once sent buffers counter reaches a value,
which is higher than one specified in MVNETA_TXQ_SIZE_REG(q). This
behavior was confirmed during tests. Also when testing the SoC working
as a NAS device, better performance was observed with int-per-packet,
as it strongly depends on the fact that all transmitted packets are
released immediately.
This commit enables NETA controller work in interrupt per sent packet mode
by setting coalescing threshold to 0.
Signed-off-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: <stable@vger.kernel.org> # v3.10+
Fixes aebea2ba0f74 ("net: mvneta: fix Tx interrupt delay")
Acked-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If mvneta_mdio_probe() fails, a kernel warning is triggered due to
missing cleanup in the error path. Add the necessary cleanup.
------------[ cut here ]------------
WARNING: CPU: 1 PID: 281 at kernel/irq/manage.c:1814 __free_percpu_irq+0xfc/0x130
percpu IRQ 38 still enabled on CPU0!
Modules linked in: bnep bluetooth xhci_plat_hcd xhci_hcd marvell_cesa armada_thermal des_generic ehci_orion mcp3021 spi_orion sfp mdio_i2c evbug fuse
CPU: 1 PID: 281 Comm: connmand Not tainted 4.7.0-rc2+ #53
Hardware name: Marvell Armada 380/385 (Device Tree)
Backtrace:
[<c0013488>] (dump_backtrace) from [<c00137d0>] (show_stack+0x18/0x1c)
r6:60010093 r5:ffffffff r4:00000000 r3:dc8ba500
[<c00137b8>] (show_stack) from [<c02c6fe0>] (dump_stack+0xa4/0xdc)
[<c02c6f3c>] (dump_stack) from [<c002d4ec>] (__warn+0xd8/0x104)
r6:c081e6a0 r5:00000000 r4:edfe5d50 r3:dc8ba500
[<c002d414>] (__warn) from [<c002d5d0>] (warn_slowpath_fmt+0x40/0x48)
r10:a0010013 r8:c09356f8 r7:00000026 r6:ef11a260 r5:edd7b980 r4:ef11a200
[<c002d594>] (warn_slowpath_fmt) from [<c008c8e0>] (__free_percpu_irq+0xfc/0x130)
r3:00000026 r2:c081e7ac
[<c008c7e4>] (__free_percpu_irq) from [<c008c95c>] (free_percpu_irq+0x48/0x74)
r10:00008914 r8:00000000 r7:ffffffed r6:c09356f8 r5:00000026 r4:ef11a200
[<c008c914>] (free_percpu_irq) from [<c043dd70>] (mvneta_open+0x118/0x134)
r6:ffffffed r5:ef01e640 r4:ef01e000 r3:ef01e000
[<c043dc58>] (mvneta_open) from [<c055f5b4>] (__dev_open+0xa4/0x108)
r7:ef01e030 r6:c06ff3d8 r5:ffff9003 r4:ef01e000
[<c055f510>] (__dev_open) from [<c055f844>] (__dev_change_flags+0x94/0x150)
r7:00001002 r6:00000001 r5:ffff9003 r4:ef01e000
[<c055f7b0>] (__dev_change_flags) from [<c055f938>] (dev_change_flags+0x20/0x50)
r8:00000000 r7:c09334c8 r6:00001002 r5:00000148 r4:ef01e000 r3:00008914
[<c055f918>] (dev_change_flags) from [<c05de044>] (devinet_ioctl+0x6f4/0x7e0)
r8:00000000 r7:c09334c8 r6:00000000 r5:ee87200c r4:00000000 r3:00008914
[<c05dd950>] (devinet_ioctl) from [<c05e0168>] (inet_ioctl+0x1b8/0x1c8)
r10:beb4499c r9:edfe4000 r8:ecf13280 r7:c096cf00 r6:beb4499c r5:eef7c240
r4:00008914
[<c05dffb0>] (inet_ioctl) from [<c053c898>] (sock_ioctl+0x78/0x300)
[<c053c820>] (sock_ioctl) from [<c0155ecc>] (do_vfs_ioctl+0x98/0xa60)
r7:00000011 r6:00008914 r5:00000011 r4:c01568d0
[<c0155e34>] (do_vfs_ioctl) from [<c01568d0>] (SyS_ioctl+0x3c/0x60)
r10:00000000 r9:edfe4000 r8:beb4499c r7:00000011 r6:00008914 r5:ecf13280
r4:ecf13280
[<c0156894>] (SyS_ioctl) from [<c000fe60>] (ret_fast_syscall+0x0/0x1c)
r8:c0010004 r7:00000036 r6:00000011 r5:000a2978 r4:00000000 r3:00009003
---[ end trace 711f625d5b04b3a7 ]---
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 3b9d6da67e11 ("cpu/hotplug: Fix rollback during error-out
in __cpu_disable()") it is ensured that callbacks of CPU_ONLINE and
CPU_DOWN_PREPARE are processed on the hotplugged CPU. Due to this SMP
function calls are no longer required.
Replace smp_call_function_single() with a direct call to
mvneta_percpu_enable() or mvneta_percpu_disable(). The functions do
not require to be called with interrupts disabled, therefore the
smp_call_function_single() calling convention is not preserved.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After enabling per-cpu processing it appeared that under heavy load
changing MTU can result in blocking all port's interrupts and
transmitting data is not possible after the change.
This commit fixes above issue by disabling percpu interrupts for the
time, when TXQs and RXQs are reconfigured.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
L1_CACHE_BYTES may not be the real cacheline size, use cache_line_size
to determine the cacheline size in runtime.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Suggested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mvneta is also used in some Marvell berlin family SoCs which may
have 64bytes cacheline size. Replace the MVNETA_CPU_D_CACHE_LINE_SIZE
usage with L1_CACHE_BYTES.
And since dma_alloc_coherent() is always cacheline size aligned, so
remove the align checks.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some literal values are actually already defined by macros, so let's use
them.
[gregory.clement@free-electrons.com: split intial commit in two
individual changes]
Signed-off-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit corrects error printing when shutting down the port.
[gregory.clement@free-electrons.com: split initial commit in two
individual changes]
Signed-off-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Function eth_prepare_mac_addr_change() is called as part of MAC
address change. This function check if interface is running.
To enable change MAC address when interface is running:
IFF_LIVE_ADDR_CHANGE flag must be set to dev->priv_flags field
Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP
network unit")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the previous patch, the spinlock was not initialized. While it didn't
cause any trouble yet it could be a problem to use it uninitialized.
The most annoying part was the critical section protected by the spinlock
in mvneta_stop(). Some of the functions could sleep as pointed when
activated CONFIG_DEBUG_ATOMIC_SLEEP. Actually, in mvneta_stop() we only
need to protect the is_stopped flagged, indeed the code of the notifier
for CPU online is protected by the same spinlock, so when we get the
lock, the notifer work is done.
Reported-by: Patrick Uiterwijk <patrick@puiterwijk.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mvneta_percpu_notifier() hotplug callback lacks handling of the
CPU_DOWN_FAILED case. That means, if CPU_DOWN_PREPARE failes, the
driver is not well configured on the CPU.
Add handling for CPU_DOWN_FAILED[_FROZEN] hotplug notifier transition
to setup the driver.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that the hardware buffer management framework had been introduced,
let's use it.
Tested-by: Sebastian Careba <nitroshift@yahoo.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Buffer manager (BM) is a dedicated hardware unit that can be used by all
ethernet ports of Armada XP and 38x SoC's. It allows to offload CPU on RX
path by sparing DRAM access on refilling buffer pool, hardware-based
filling of descriptor ring data and better memory utilization due to HW
arbitration for using 'short' pools for small packets.
Tests performed with A388 SoC working as a network bridge between two
packet generators showed increase of maximum processed 64B packets by
~20k (~555k packets with BM enabled vs ~535 packets without BM). Also
when pushing 1500B-packets with a line rate achieved, CPU load decreased
from around 25% without BM to 20% with BM.
BM comprise up to 4 buffer pointers' (BP) rings kept in DRAM, which
are called external BP pools - BPPE. Allocating and releasing buffer
pointers (BP) to/from BPPE is performed indirectly by write/read access
to a dedicated internal SRAM, where internal BP pools (BPPI) are placed.
BM hardware controls status of BPPE automatically, as well as assigning
proper buffers to RX descriptors. For more details please refer to
Functional Specification of Armada XP or 38x SoC.
In order to enable support for a separate hardware block, common for all
ports, a new driver has to be implemented ('mvneta_bm'). It provides
initialization sequence of address space, clocks, registers, SRAM,
empty pools' structures and also obtaining optional configuration
from DT (please refer to device tree binding documentation). mvneta_bm
exposes also a necessary API to mvneta driver, as well as a dedicated
structure with BM information (bm_priv), whose presence is used as a
flag notifying of BM usage by port. It has to be ensured that mvneta_bm
probe is executed prior to the ones in ports' driver. In case BM is not
used or its probe fails, mvneta falls back to use software buffer
management.
A sequence executed in mvneta_probe function is modified in order to have
an access to needed resources before possible port's BM initialization is
done. According to port-pools mapping provided by DT appropriate registers
are configured and the buffer pools are filled. RX path is modified
accordingly. Becaues the hardware allows a wide variety of configuration
options, following assumptions are made:
* using BM mechanisms can be selectively disabled/enabled basing
on DT configuration among the ports
* 'long' pool's single buffer size is tied to port's MTU
* using 'long' pool by port is obligatory and it cannot be shared
* using 'short' pool for smaller packets is optional
* one 'short' pool can be shared among all ports
This commit enables hardware buffer management operation cooperating with
existing mvneta driver. New device tree binding documentation is added and
the one of mvneta is updated accordingly.
[gregory.clement@free-electrons.com: removed the suspend/resume part]
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When stopping the port, the CPU notifier are still there whereas the
mvneta_stop_dev function calls mvneta_percpu_disable() on each CPUs.
It was possible to have a new CPU coming at this point which could be
racy.
This patch adds a flag preventing executing the code notifier for a new
CPU when the port is stopping. It also uses the spinlock introduces
previously. To avoid the deadlock, the lock has been moved outside the
mvneta_percpu_elect function.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Electing a CPU must be done in an atomic way: it should be done after or
before the removal/insertion of a CPU and this function is not reentrant.
During the loop of mvneta_percpu_elect we associates the queues to the
CPUs, if there is a topology change during this loop, then the mapping
between the CPUs and the queues could be wrong. During this loop the
interrupt mask is also updating for each CPUs, It should not be changed
in the same time by other part of the driver.
This patch adds spinlock to create the needed critical sections.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the MVNETA_INTR_* registers, the queues related fields are per cpu,
according to the datasheet (comment in [] are added by me):
"In a multi-CPU system, bits of RX[or TX] queues for which the access by
the reading[or writing] CPU is disabled are read as 0, and cannot be
cleared[or written]."
That means that each time we want to manipulate these bits we had to do
it on each cpu and not only on the current cpu.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the commit 2dcf75e2793c ("net: mvneta: Associate RX queues with
each CPU") all the percpu irq are used and disabled at initialization, so
there is no point to disable them first.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of using a for_each_* loop in which we just call the
smp_call_function_single macro, it is more simple to directly use the
on_each_cpu macro. Moreover, this macro ensures that the calls will be
done all at once.
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When passing to the management of multiple RX queue, the
mvneta_percpu_elect function was broken. The use of the modulo can lead
to elect the wrong cpu. For example with rxq_def=2, if the CPU 2 goes
offline and then online, we ended with the third RX queue activated in
the same time on CPU 0 and CPU2, which lead to a kernel crash.
With this fix, we don't try to get "the closer" CPU if the default CPU is
gone, now we just use CPU 0 which always be there. Thanks to this, the
code becomes more readable, easier to maintain and more predicable.
Cc: stable@vger.kernel.org
Fixes: 2dcf75e2793c ("net: mvneta: Associate RX queues with each CPU")
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch convert the for_each_present in on_each_cpu, instead of
applying on the present cpus it will be applied only on the online cpus.
This fix a bug reported on
http://thread.gmane.org/gmane.linux.ports.arm.kernel/468173.
Using the macro on_each_cpu (instead of a for_each_* loop) also ensures
that all the calls will be done all at once.
Fixes: f86428854480 ("net: mvneta: Statically assign queues to CPUs")
Reported-by: Stefan Roese <stefan.roese@gmail.com>
Suggested-by: Jisheng Zhang <jszhang@marvell.com>
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some platforms may provide more than one clk for the mvneta IP, for
example Marvell BG4CT provides one clk for the mac core, and one
clk for the AXI bus logic. Obviously this bus clk also need to
be enabled. This patch adds this optional "bus" clk support.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some platforms may provide more than one clk for the mvneta IP, for
example Marvell BG4CT provides one clk for the mac core, and one
clk for the AXI bus logic.
To support for more than one clock, we'll need to distinguish between
the clock by name. Change clock probing to first try to get "core"
clock before falling back to unnamed clock.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sorting the headers in alphabetic order will help to reduce the conflict
when adding new headers in the future.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When s->type is T_REG_64, the high 32bits are lost in val. This patch
fixes this trivial issue.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Fixes: 9b0cdefa4cd5 ("net: mvneta: add ethtool statistics")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With this patch each CPU is associated with its own set of TX queues.
It also setup the XPS with an initial configuration which set the
affinity matching the hardware configuration.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the support for the RSS related ethtool
function. Currently it only uses one entry in the indirection table which
allows associating an mvneta interface to a given CPU.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We enable the percpu interrupt for all the CPU and we just associate a
CPU to a few queue at the neta level. The mapping between the CPUs and
the queues is static. The queues are associated to the CPU module the
number of CPUs. However currently we only use on RX queue for a given
Ethernet port.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of using the same default queue for all the port. Move it in the
port struct. It will allow have a different default queue for each port.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/renesas/ravb_main.c
kernel/bpf/syscall.c
net/ipv4/ipmr.c
All three conflicts were cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch allows to do
ethtool -s eth0 autoneg off
ethtool -s eth0 autoneg on
to disable or enable autonegotiation at run-time.
Without that functionality, the only way to control the autonegotiation
is to modify the device tree.
This is needed if you plan to use the same kernel with
different ethernet switches, the ones that support the in-band
status and the ones that not.
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Stas Sergeev <stsp@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This moves autoneg-related bit manipulations to the single place.
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Stas Sergeev <stsp@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since Armada 38x SoC can support IP checksum for jumbo frames only on
a single port, it means that this feature should be enabled per-port,
rather than for the whole SoC.
This patch enables setting custom TX IP checksum limit by adding new
optional property to the mvneta device tree node. If not used, by
default 1600B is set for "marvell,armada-370-neta" and 9800B for other
strings, which ensures backward compatibility. Binding documentation
is updated accordingly.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the actual RX processing, there is same error path for both descriptor
ring refilling and building skb fails. This is not correct, because after
successful refill, the ring is already updated with newly allocated
buffer. Then, in case of build_skb() fail, hitherto code left the original
buffer unmapped.
This patch fixes above situation by swapping error check of skb build with
DMA-unmap of original buffer.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: <stable@vger.kernel.org> # v4.2+
Fixes a84e32894191 ("net: mvneta: fix refilling for Rx DMA buffers")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A value originally defined in the driver was inappropriate. Even though
the ingress was somehow working, writing MVNETA_RXQ_INTR_ENABLE_ALL_MASK
to MVNETA_INTR_ENABLE didn't make any effect, because the bits [31:16]
are reserved and read-only.
This commit updates MVNETA_RXQ_INTR_ENABLE_ALL_MASK to be compliant with
the controller's documentation.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network
unit")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MVNETA_RXQ_HW_BUF_ALLOC bit which controls enabling hardware buffer
allocation was mistakenly set as BIT(1). This commit fixes the assignment.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network
unit")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit adds missing configuration of MBUS windows access protection
in mvneta_conf_mbus_windows function - a dedicated variable for that
purpose remained there unused since v3.8 initial mvneta support. Because
of that the register contents were inherited from the bootloader.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network
unit")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After changing an interface's MTU, then bringing the interface down and
back up again, I immediately saw tons of kernel messages like below.
The reason for this bad behavior is mvneta_rxq_drop_pkts(), which calls
dma_unmap_single() on already-freed memory. So we need to switch the
order of those two operations.
[ 152.388518] BUG: Bad page state in process ifconfig pfn:1b518
[ 152.388526] page:dff3dbc0 count:0 mapcount:0 mapping: (null) index:0x0
[ 152.395178] flags: 0x200(arch_1)
[ 152.398441] page dumped because: PAGE_FLAGS_CHECK_AT_PREP flag set
[ 152.398446] bad because of flags:
[ 152.398450] flags: 0x200(arch_1)
[ 152.401716] Modules linked in:
[ 152.401728] CPU: 0 PID: 1453 Comm: ifconfig Tainted: P B O 4.1.12.armada.1 #1
[ 152.401733] Hardware name: Marvell Armada 370/XP (Device Tree)
[ 152.401749] [<c0015b1c>] (unwind_backtrace) from [<c0011d8c>] (show_stack+0x10/0x14)
[ 152.401762] [<c0011d8c>] (show_stack) from [<c06aa68c>] (dump_stack+0x74/0x90)
[ 152.401772] [<c06aa68c>] (dump_stack) from [<c0096c08>] (bad_page+0xc4/0x124)
[ 152.401783] [<c0096c08>] (bad_page) from [<c0099378>] (get_page_from_freelist+0x4e4/0x644)
[ 152.401794] [<c0099378>] (get_page_from_freelist) from [<c0099620>] (__alloc_pages_nodemask+0x148/0x784)
[ 152.401805] [<c0099620>] (__alloc_pages_nodemask) from [<c00ac658>] (kmalloc_order+0x10/0x20)
[ 152.401818] [<c00ac658>] (kmalloc_order) from [<c04c6f44>] (mvneta_rx_refill+0xc4/0xe8)
[ 152.401830] [<c04c6f44>] (mvneta_rx_refill) from [<c04c96c0>] (mvneta_setup_rxqs+0x298/0x39c)
[ 152.401842] [<c04c96c0>] (mvneta_setup_rxqs) from [<c04c9904>] (mvneta_open+0x3c/0x150)
[ 152.401853] [<c04c9904>] (mvneta_open) from [<c0597764>] (__dev_open+0xac/0x124)
[ 152.401864] [<c0597764>] (__dev_open) from [<c05979e4>] (__dev_change_flags+0x8c/0x148)
[ 152.401875] [<c05979e4>] (__dev_change_flags) from [<c0597ac0>] (dev_change_flags+0x18/0x48)
[ 152.401886] [<c0597ac0>] (dev_change_flags) from [<c060d308>] (devinet_ioctl+0x620/0x6d0)
[ 152.401897] [<c060d308>] (devinet_ioctl) from [<c057d810>] (sock_ioctl+0x64/0x288)
[ 152.401908] [<c057d810>] (sock_ioctl) from [<c00dcb7c>] (do_vfs_ioctl+0x78/0x608)
[ 152.401918] [<c00dcb7c>] (do_vfs_ioctl) from [<c00dd170>] (SyS_ioctl+0x64/0x74)
[ 152.401930] [<c00dd170>] (SyS_ioctl) from [<c000f3a0>] (ret_fast_syscall+0x0/0x3c)
Signed-off-by: Justin Maggard <jmaggard@netgear.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The existing function to clear the MIB statatistics was using the
wrong address for the registers. Also, the counters would of been
cleared when the interface was brought up, not during the
probe. Fix both of these.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the ethtool statistic interface, returning the full set
of statistics which both Armada 370, 38x and Armada XP can support.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the switch to per-CPU interrupts, we lost the ability to set which
CPU was going to receive our RX interrupt, which was now only the CPU on
which the mvneta_open function was run.
We can now assign our queues to their respective CPUs, and make sure only
this CPU is going to handle our traffic.
This also paves the road to be able to change that at runtime, and later on
to support RSS.
[gregory.clement@free-electrons.com]: hardened the CPU hotplug support.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mvneta driver allows to change the default RX queue trough the rxq_def
kernel parameter.
However, the current code doesn't allow to have any value but 0. It is
actively checked for in the driver's probe because the drivers makes a
number of assumption and takes a number of shortcuts in order to just use
that RX queue.
Remove these limitations in order to be able to specify any available
queue.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that our interrupt controller is allowing us to use per-CPU interrupts,
actually use it in the mvneta driver.
This involves obviously reworking the driver to have a CPU-local NAPI
structure, and report for incoming packet using that structure.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CPU_MAP register is duplicated for each CPUs at different addresses,
each instance being at a different address.
However, the code so far was using CONFIG_NR_CPUS to initialise the CPU_MAP
registers for each registers, while the SoCs embed at most 4 CPUs.
This is especially an issue with multi_v7_defconfig, where CONFIG_NR_CPUS
is currently set to 16, resulting in writes to registers that are not
CPU_MAP.
Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Linus Torvalds
Baoyou Xie
Sebastian Andrzej Siewior
Philippe Reynes
Peter Chen
Dmitri Epshtein
Russell King - ARM Linux
Anna-Maria Gleixner
Marcin Wojtas
Jisheng Zhang
Gregory CLEMENT
Andrew Lunn
David S. Miller
Stas Sergeev
Justin Maggard
Russell King
Maxime Ripard