| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The classification operations that are used for RSS make use of several
lookup tables. Having hit counters for these tables is really helpful
to determine what flows were matched by ingress traffic, and see the
path of packets among all the classifier tables.
This commit adds hit counters for the 3 tables used at the moment :
- The decoding table (also called lookup_id table), that links flows
identified by the Header Parser to the flow table.
There's one entry per flow, located at :
.../mvpp2/<controller>/flows/XX/dec_hits
Note that there are 21 flows in the decoding table, whereas there are
52 flows in the Header Parser. That's because there are several kind
of traffic that will match a given flow. Reading the hit counter from
one sub-flow will clear all hit counter that have the same flow_id.
This also applies to the flow_hits.
- The flow table, that contains all the different lookups to be
performed by the classifier for each packet of a given flow. The match
is done on the first entry of the flow sequence.
- The C2 engine entries, that are used to assign the default rx queue,
and enable or disable RSS for a given port.
There's one entry per flow, located at:
.../mvpp2/<controller>/flows/XX/flow_hits
There is one C2 entry per port, so the c2 hit counter is located at :
.../mvpp2/<controller>/ethX/c2_hits
All hit counter values are 16-bits clear-on-read values.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The classifier configuration for RSS is quite complex, with several
lookup tables being used. This commit adds useful info in debugfs to
see how the different tables are configured :
Added 2 new entries in the per-port directory :
- .../eth0/default_rxq : The default rx queue on that port
- .../eth0/rss_enable : Indicates if RSS is enabled in the C2 entry
Added the 'flows' directory :
It contains one entry per sub-flow. a 'sub-flow' is a unique path from
Header Parser to the flow table. Multiple sub-flows can point to the
same 'flow' (each flow has an id from 8 to 29, which is its index in the
Lookup Id table) :
- .../flows/00/...
/01/...
...
/51/id : The flow id. There are 21 unique flows. There's one
flow per combination of the following parameters :
- L4 protocol (TCP, UDP, none)
- L3 protocol (IPv4, IPv6)
- L3 parameters (Fragmented or not)
- L2 parameters (Vlan tag presence or not)
.../type : The flow type. This is an even higher level flow,
that we manipulate with ethtool. It can be :
"udp4" "tcp4" "udp6" "tcp6" "ipv4" "ipv6" "other".
.../eth0/...
.../eth1/engine : The hash generation engine used for this
flow on the given port
.../hash_opts : The hash generation options indicating on
what data we base the hash (vlan tag, src
IP, src port, etc.)
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One helpful feature to help debug the Header Parser TCAM filter in PPv2
is to be able to see if the entries did match something when a packet
comes in. This can be done by using the built-in hit counter for TCAM
entries.
This commit implements reading the counter, and exposing its value on
debugfs for each filter entry.
The counter is a 16-bits clear-on-read value, located at:
.../mvpp2/<controller>/parser/XXX/hits
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marvell PPv2 Packer Header Parser has a TCAM based filter, that is not
trivial to configure and debug. Being able to dump TCAM entries from
userspace can be really helpful to help development of new features
and debug existing ones.
This commit adds a basic debugfs interface for the PPv2 driver, focusing
on TCAM related features.
<mnt>/mvpp2/ --- f2000000.ethernet
\- f4000000.ethernet --- parser --- 000 ...
| \- 001
| \- ...
| \- 255 --- ai
| \- header_data
| \- lookup_id
| \- sram
| \- valid
\- eth1 ...
\- eth2 --- mac_filter
\- parser_entries
\- vid_filter
There's one directory per PPv2 instance, named after pdev->name to make
sure names are uniques. In each of these directories, there's :
- one directory per interface on the controller, each containing :
- "mac_filter", which lists all filtered addresses for this port
(based on TCAM, not on the kernel's uc / mc lists)
- "parser_entries", which lists the indices of all valid TCAM
entries that have this port in their port map
- "vid_filter", which lists the vids allowed on this port, based on
TCAM
- one "parser" directory (the parser is common to all ports), containing :
- one directory per TCAM entry (256 of them, from 0 to 255), each
containing :
- "ai" : Contains the 1 byte Additional Info field from TCAM, and
- "header_data" : Contains the 8 bytes Header Data extracted from
the packet
- "lookup_id" : Contains the 4 bits LU_ID
- "sram" : contains the raw SRAM data, which is the result of the TCAM
lookup. This readonly at the moment.
- "valid" : Indicates if the entry is valid of not.
All entries are read-only, and everything is output in hex form.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the appropriate SPDX license identifiers and drop the license text.
This patch is only cosmetic.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PPv2 Controller has a classifier, that can perform multiple lookup
operations for each packet, using different engines.
One of these engines is the C2 engine, which performs TCAM based lookups
on data extracted from the packet header. When a packet matches an
entry, the engine sets various attributes, used to perform
classification operations.
One of these attributes is the rx queue in which the packet should be sent.
The current code uses the lookup_id table (also called decoding table)
to assign the rx queue. However, this only works if we use one entry per
port in the decoding table, which won't be the case once we add RSS
lookups.
This patch uses the C2 engine to assign the rx queue to each packet.
The C2 engine is used through the flow table, which dictates what
classification operations are done for a given flow.
Right now, we have one flow per port, which contains every ingress
packet for this port.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the RSS indirection table support, allowing to use the
ethtool -x and -X options to dump and set this table.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
[Maxime: Small warning fixes, use one table per port]
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no RSS_TABLE register in PPv2 Controller. The register 0x1510
which was specified is actually named "RSS_HASH_SEL", but isn't used by
this driver at all.
Based on how this register was used, it should have been the
RXQ2RSS_TABLE register, which allows to select the RSS table that will
be used for the incoming packet.
The RSS_TABLE_POINTER is actually a field of this RXQ2RSS_TABLE
register.
Since RSS tables are actually not used by the driver for now, this
commit does not fix a runtime bug.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The number of receive queue per port is :
- MVPP2_DEFAULT_RXQ if in single queue mode
- MVPP2_DEFAULT_RXQ * num_possible_cpus if in multi queue mode
with MVPP2_DEFAULT_RXQ = 4.
However, we don't use the extra rx queues at the moment, we really only
need one per port per CPU, until some more advanced classification rules
are implemented.
Suggested-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The size of the the RSS indirection tables should be defined in mvpp2.h,
so that we can use it in all files of the PPv2 driver.
This commit moves the define in mvpp2.h, and adds the missing #include
in mvpp2_cls.h.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Marvell PPv2 driver uses interrupts and tasklet but does not
explicitly include linux/interrupt.h, relying on implicit includes. This
one particularly is included by chance after a long unlogical chain of
inclusions. Fix this so we do not get future build breaks.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PPv2's Header Parser use some large TCAM and SRAM entries, that are
duplicated in software so that we can write them to hardware only when
we are done modifying them.
Currently, PPv2 uses a union containing arrays of u32 and u8 to represent
these entries, to facilitate byte per byte access. This representation is
broken when we want to support big endian, and this makes the code
confusing to read.
This patch drops the union, and simply stores the TCAM and SRAM entries
as u32 arrays, each entry corresponding to a 32-bit register.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PPv2 controller always expect descriptors to be in little endian. We
must therefore force descriptors to use that format, and convert to the
host endianness when necessary.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As the mvpp2 driver is growing, move this driver to a dedicated
directory and split it into several files.
Since this driver has a lot of register defines and structure
definitions, it can benefit from having all of this into a dedicated
header file, named mvpp2.h.
A good chunk of the mvpp2 code is dedicated to Header Parser handling, so
we introduce mvpp2_prs.h where all Header Parser definitions are located,
and mvpp2_prs.c containing the related code.
In the same way, mvpp2_cls.h and mvpp2_cls.c are created to contain
Classifier and RSS related code.
The former 'mvpp2.c' file is renamed 'mvpp2_main.c' so that we can keep
the driver binary named 'mvpp2'.
This commit is only about spliting the driver into multiple files and
doesn't introduce any new function, feature or fix besides removing
'static' keywords when needed.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Maxime Chevallier
Antoine Tenart