aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/marvell (unfollow)
AgeCommit message (Collapse)AuthorFilesLines
2020-02-16net: ks8851-ml: Fix 16-bit IO operationMarek Vasut1-2/+2
The Micrel KSZ8851-16MLLI datasheet DS00002357B page 12 states that BE[3:0] signals are active high. This contradicts the measurements of the behavior of the actual chip, where these signals behave as active low. For example, to read the CIDER register, the bus must expose 0xc0c0 during the address phase, which means BE[3:0]=4'b1100. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: ks8851-ml: Fix 16-bit data accessMarek Vasut1-2/+2
The packet data written to and read from Micrel KSZ8851-16MLLI must be byte-swapped in 16-bit mode, add this byte-swapping. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: ks8851-ml: Remove 8-bit bus accessorsMarek Vasut1-40/+5
This driver is mixing 8-bit and 16-bit bus accessors for reasons unknown, however the speculation is that this was some sort of attempt to support the 8-bit bus mode. As per the KS8851-16MLL documentation, all two registers accessed via the 8-bit accessors are internally 16-bit registers, so reading them using 16-bit accessors is fine. The KS_CCR read can be converted to 16-bit read outright, as it is already a concatenation of two 8-bit reads of that register. The KS_RXQCR accesses are 8-bit only, however writing the top 8 bits of the register is OK as well, since the driver caches the entire 16-bit register value anyway. Finally, the driver is not used by any hardware in the kernel right now. The only hardware available to me is one with 16-bit bus, so I have no way to test the 8-bit bus mode, however it is unlikely this ever really worked anyway. If the 8-bit bus mode is ever required, it can be easily added by adjusting the 16-bit accessors to do 2 consecutive accesses, which is how this should have been done from the beginning. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16mptcp: select CRYPTOMatthieu Baerts1-0/+1
Without this modification and if CRYPTO is not selected, we have this warning: WARNING: unmet direct dependencies detected for CRYPTO_LIB_SHA256 Depends on [n]: CRYPTO [=n] Selected by [y]: - MPTCP [=y] && NET [=y] && INET [=y] MPTCP selects CRYPTO_LIB_SHA256 which seems to depend on CRYPTO. CRYPTO is now selected to avoid this issue. Even though the config system prints that warning, it looks like sha256.c is compiled and linked even without CONFIG_CRYPTO. Since MPTCP will end up needing CONFIG_CRYPTO anyway in future commits -- currently in preparation for net-next -- we propose to add it now to fix the warning. The dependency in the config system comes from the fact that CRYPTO_LIB_SHA256 is defined in "lib/crypto/Kconfig" which is sourced from "crypto/Kconfig" only if CRYPTO is selected. Fixes: 65492c5a6ab5 (mptcp: move from sha1 (v0) to sha256 (v1)) Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16bonding: fix lockdep warning in bond_get_stats()Taehee Yoo1-3/+50
In the "struct bonding", there is stats_lock. This lock protects "bond_stats" in the "struct bonding". bond_stats is updated in the bond_get_stats() and this function would be executed concurrently. So, the lock is needed. Bonding interfaces would be nested. So, either stats_lock should use dynamic lockdep class key or stats_lock should be used by spin_lock_nested(). In the current code, stats_lock is using a dynamic lockdep class key. But there is no updating stats_lock_key routine So, lockdep warning will occur. Test commands: ip link add bond0 type bond ip link add bond1 type bond ip link set bond0 master bond1 ip link set bond0 nomaster ip link set bond1 master bond0 Splat looks like: [ 38.420603][ T957] 5.5.0+ #394 Not tainted [ 38.421074][ T957] ------------------------------------------------------ [ 38.421837][ T957] ip/957 is trying to acquire lock: [ 38.422399][ T957] ffff888063262cd8 (&bond->stats_lock_key#2){+.+.}, at: bond_get_stats+0x90/0x4d0 [bonding] [ 38.423528][ T957] [ 38.423528][ T957] but task is already holding lock: [ 38.424526][ T957] ffff888065fd2cd8 (&bond->stats_lock_key){+.+.}, at: bond_get_stats+0x90/0x4d0 [bonding] [ 38.426075][ T957] [ 38.426075][ T957] which lock already depends on the new lock. [ 38.426075][ T957] [ 38.428536][ T957] [ 38.428536][ T957] the existing dependency chain (in reverse order) is: [ 38.429475][ T957] [ 38.429475][ T957] -> #1 (&bond->stats_lock_key){+.+.}: [ 38.430273][ T957] _raw_spin_lock+0x30/0x70 [ 38.430812][ T957] bond_get_stats+0x90/0x4d0 [bonding] [ 38.431451][ T957] dev_get_stats+0x1ec/0x270 [ 38.432088][ T957] bond_get_stats+0x1a5/0x4d0 [bonding] [ 38.432767][ T957] dev_get_stats+0x1ec/0x270 [ 38.433322][ T957] rtnl_fill_stats+0x44/0xbe0 [ 38.433866][ T957] rtnl_fill_ifinfo+0xeb2/0x3720 [ 38.434474][ T957] rtmsg_ifinfo_build_skb+0xca/0x170 [ 38.435081][ T957] rtmsg_ifinfo_event.part.33+0x1b/0xb0 [ 38.436848][ T957] rtnetlink_event+0xcd/0x120 [ 38.437455][ T957] notifier_call_chain+0x90/0x160 [ 38.438067][ T957] netdev_change_features+0x74/0xa0 [ 38.438708][ T957] bond_compute_features.isra.45+0x4e6/0x6f0 [bonding] [ 38.439522][ T957] bond_enslave+0x3639/0x47b0 [bonding] [ 38.440225][ T957] do_setlink+0xaab/0x2ef0 [ 38.440786][ T957] __rtnl_newlink+0x9c5/0x1270 [ 38.441463][ T957] rtnl_newlink+0x65/0x90 [ 38.442075][ T957] rtnetlink_rcv_msg+0x4a8/0x890 [ 38.442774][ T957] netlink_rcv_skb+0x121/0x350 [ 38.443451][ T957] netlink_unicast+0x42e/0x610 [ 38.444282][ T957] netlink_sendmsg+0x65a/0xb90 [ 38.444992][ T957] ____sys_sendmsg+0x5ce/0x7a0 [ 38.445679][ T957] ___sys_sendmsg+0x10f/0x1b0 [ 38.446365][ T957] __sys_sendmsg+0xc6/0x150 [ 38.447007][ T957] do_syscall_64+0x99/0x4f0 [ 38.447668][ T957] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 38.448538][ T957] [ 38.448538][ T957] -> #0 (&bond->stats_lock_key#2){+.+.}: [ 38.449554][ T957] __lock_acquire+0x2d8d/0x3de0 [ 38.450148][ T957] lock_acquire+0x164/0x3b0 [ 38.450711][ T957] _raw_spin_lock+0x30/0x70 [ 38.451292][ T957] bond_get_stats+0x90/0x4d0 [bonding] [ 38.451950][ T957] dev_get_stats+0x1ec/0x270 [ 38.452425][ T957] bond_get_stats+0x1a5/0x4d0 [bonding] [ 38.453362][ T957] dev_get_stats+0x1ec/0x270 [ 38.453825][ T957] rtnl_fill_stats+0x44/0xbe0 [ 38.454390][ T957] rtnl_fill_ifinfo+0xeb2/0x3720 [ 38.456257][ T957] rtmsg_ifinfo_build_skb+0xca/0x170 [ 38.456998][ T957] rtmsg_ifinfo_event.part.33+0x1b/0xb0 [ 38.459351][ T957] rtnetlink_event+0xcd/0x120 [ 38.460086][ T957] notifier_call_chain+0x90/0x160 [ 38.460829][ T957] netdev_change_features+0x74/0xa0 [ 38.461752][ T957] bond_compute_features.isra.45+0x4e6/0x6f0 [bonding] [ 38.462705][ T957] bond_enslave+0x3639/0x47b0 [bonding] [ 38.463476][ T957] do_setlink+0xaab/0x2ef0 [ 38.464141][ T957] __rtnl_newlink+0x9c5/0x1270 [ 38.464897][ T957] rtnl_newlink+0x65/0x90 [ 38.465522][ T957] rtnetlink_rcv_msg+0x4a8/0x890 [ 38.466215][ T957] netlink_rcv_skb+0x121/0x350 [ 38.466895][ T957] netlink_unicast+0x42e/0x610 [ 38.467583][ T957] netlink_sendmsg+0x65a/0xb90 [ 38.468285][ T957] ____sys_sendmsg+0x5ce/0x7a0 [ 38.469202][ T957] ___sys_sendmsg+0x10f/0x1b0 [ 38.469884][ T957] __sys_sendmsg+0xc6/0x150 [ 38.470587][ T957] do_syscall_64+0x99/0x4f0 [ 38.471245][ T957] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 38.472093][ T957] [ 38.472093][ T957] other info that might help us debug this: [ 38.472093][ T957] [ 38.473438][ T957] Possible unsafe locking scenario: [ 38.473438][ T957] [ 38.474898][ T957] CPU0 CPU1 [ 38.476234][ T957] ---- ---- [ 38.480171][ T957] lock(&bond->stats_lock_key); [ 38.480808][ T957] lock(&bond->stats_lock_key#2); [ 38.481791][ T957] lock(&bond->stats_lock_key); [ 38.482754][ T957] lock(&bond->stats_lock_key#2); [ 38.483416][ T957] [ 38.483416][ T957] *** DEADLOCK *** [ 38.483416][ T957] [ 38.484505][ T957] 3 locks held by ip/957: [ 38.485048][ T957] #0: ffffffffbccf6230 (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x457/0x890 [ 38.486198][ T957] #1: ffff888065fd2cd8 (&bond->stats_lock_key){+.+.}, at: bond_get_stats+0x90/0x4d0 [bonding] [ 38.487625][ T957] #2: ffffffffbc9254c0 (rcu_read_lock){....}, at: bond_get_stats+0x5/0x4d0 [bonding] [ 38.488897][ T957] [ 38.488897][ T957] stack backtrace: [ 38.489646][ T957] CPU: 1 PID: 957 Comm: ip Not tainted 5.5.0+ #394 [ 38.490497][ T957] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 38.492810][ T957] Call Trace: [ 38.493219][ T957] dump_stack+0x96/0xdb [ 38.493709][ T957] check_noncircular+0x371/0x450 [ 38.494344][ T957] ? lookup_address+0x60/0x60 [ 38.494923][ T957] ? print_circular_bug.isra.35+0x310/0x310 [ 38.495699][ T957] ? hlock_class+0x130/0x130 [ 38.496334][ T957] ? __lock_acquire+0x2d8d/0x3de0 [ 38.496979][ T957] __lock_acquire+0x2d8d/0x3de0 [ 38.497607][ T957] ? register_lock_class+0x14d0/0x14d0 [ 38.498333][ T957] ? check_chain_key+0x236/0x5d0 [ 38.499003][ T957] lock_acquire+0x164/0x3b0 [ 38.499800][ T957] ? bond_get_stats+0x90/0x4d0 [bonding] [ 38.500706][ T957] _raw_spin_lock+0x30/0x70 [ 38.501435][ T957] ? bond_get_stats+0x90/0x4d0 [bonding] [ 38.502311][ T957] bond_get_stats+0x90/0x4d0 [bonding] [ ... ] But, there is another problem. The dynamic lockdep class key is protected by RTNL, but bond_get_stats() would be called outside of RTNL. So, it would use an invalid dynamic lockdep class key. In order to fix this issue, stats_lock uses spin_lock_nested() instead of a dynamic lockdep key. The bond_get_stats() calls bond_get_lowest_level_rcu() to get the correct nest level value, which will be used by spin_lock_nested(). The "dev->lower_level" indicates lower nest level value, but this value is invalid outside of RTNL. So, bond_get_lowest_level_rcu() returns valid lower nest level value in the RCU critical section. bond_get_lowest_level_rcu() will be work only when LOCKDEP is enabled. Fixes: 089bca2caed0 ("bonding: use dynamic lockdep key instead of subclass") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: export netdev_next_lower_dev_rcu()Taehee Yoo2-7/+6
netdev_next_lower_dev_rcu() will be used to implement a function, which is to walk all lower interfaces. There are already functions that they walk their lower interface. (netdev_walk_all_lower_dev_rcu, netdev_walk_all_lower_dev()). But, there would be cases that couldn't be covered by given netdev_walk_all_lower_dev_{rcu}() function. So, some modules would want to implement own function, which is to walk all lower interfaces. In the next patch, netdev_next_lower_dev_rcu() will be used. In addition, this patch removes two unused prototypes in netdevice.h. Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16bonding: add missing netdev_update_lockdep_key()Taehee Yoo2-0/+4
After bond_release(), netdev_update_lockdep_key() should be called. But both ioctl path and attribute path don't call netdev_update_lockdep_key(). This patch adds missing netdev_update_lockdep_key(). Test commands: ip link add bond0 type bond ip link add bond1 type bond ifenslave bond0 bond1 ifenslave -d bond0 bond1 ifenslave bond1 bond0 Splat looks like: [ 29.501182][ T1046] WARNING: possible circular locking dependency detected [ 29.501945][ T1039] hardirqs last disabled at (1962): [<ffffffffac6c807f>] handle_mm_fault+0x13f/0x700 [ 29.503442][ T1046] 5.5.0+ #322 Not tainted [ 29.503447][ T1046] ------------------------------------------------------ [ 29.504277][ T1039] softirqs last enabled at (1180): [<ffffffffade00678>] __do_softirq+0x678/0x981 [ 29.505443][ T1046] ifenslave/1046 is trying to acquire lock: [ 29.505886][ T1039] softirqs last disabled at (1169): [<ffffffffac19c18a>] irq_exit+0x17a/0x1a0 [ 29.509997][ T1046] ffff88805d5da280 (&dev->addr_list_lock_key#3){+...}, at: dev_mc_sync_multiple+0x95/0x120 [ 29.511243][ T1046] [ 29.511243][ T1046] but task is already holding lock: [ 29.512192][ T1046] ffff8880460f2280 (&dev->addr_list_lock_key#4){+...}, at: bond_enslave+0x4482/0x47b0 [bonding] [ 29.514124][ T1046] [ 29.514124][ T1046] which lock already depends on the new lock. [ 29.514124][ T1046] [ 29.517297][ T1046] [ 29.517297][ T1046] the existing dependency chain (in reverse order) is: [ 29.518231][ T1046] [ 29.518231][ T1046] -> #1 (&dev->addr_list_lock_key#4){+...}: [ 29.519076][ T1046] _raw_spin_lock+0x30/0x70 [ 29.519588][ T1046] dev_mc_sync_multiple+0x95/0x120 [ 29.520208][ T1046] bond_enslave+0x448d/0x47b0 [bonding] [ 29.520862][ T1046] bond_option_slaves_set+0x1a3/0x370 [bonding] [ 29.521640][ T1046] __bond_opt_set+0x1ff/0xbb0 [bonding] [ 29.522438][ T1046] __bond_opt_set_notify+0x2b/0xf0 [bonding] [ 29.523251][ T1046] bond_opt_tryset_rtnl+0x92/0xf0 [bonding] [ 29.524082][ T1046] bonding_sysfs_store_option+0x8a/0xf0 [bonding] [ 29.524959][ T1046] kernfs_fop_write+0x276/0x410 [ 29.525620][ T1046] vfs_write+0x197/0x4a0 [ 29.526218][ T1046] ksys_write+0x141/0x1d0 [ 29.526818][ T1046] do_syscall_64+0x99/0x4f0 [ 29.527430][ T1046] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 29.528265][ T1046] [ 29.528265][ T1046] -> #0 (&dev->addr_list_lock_key#3){+...}: [ 29.529272][ T1046] __lock_acquire+0x2d8d/0x3de0 [ 29.529935][ T1046] lock_acquire+0x164/0x3b0 [ 29.530638][ T1046] _raw_spin_lock+0x30/0x70 [ 29.531187][ T1046] dev_mc_sync_multiple+0x95/0x120 [ 29.531790][ T1046] bond_enslave+0x448d/0x47b0 [bonding] [ 29.532451][ T1046] bond_option_slaves_set+0x1a3/0x370 [bonding] [ 29.533163][ T1046] __bond_opt_set+0x1ff/0xbb0 [bonding] [ 29.533789][ T1046] __bond_opt_set_notify+0x2b/0xf0 [bonding] [ 29.534595][ T1046] bond_opt_tryset_rtnl+0x92/0xf0 [bonding] [ 29.535500][ T1046] bonding_sysfs_store_option+0x8a/0xf0 [bonding] [ 29.536379][ T1046] kernfs_fop_write+0x276/0x410 [ 29.537057][ T1046] vfs_write+0x197/0x4a0 [ 29.537640][ T1046] ksys_write+0x141/0x1d0 [ 29.538251][ T1046] do_syscall_64+0x99/0x4f0 [ 29.538870][ T1046] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 29.539659][ T1046] [ 29.539659][ T1046] other info that might help us debug this: [ 29.539659][ T1046] [ 29.540953][ T1046] Possible unsafe locking scenario: [ 29.540953][ T1046] [ 29.541883][ T1046] CPU0 CPU1 [ 29.542540][ T1046] ---- ---- [ 29.543209][ T1046] lock(&dev->addr_list_lock_key#4); [ 29.543880][ T1046] lock(&dev->addr_list_lock_key#3); [ 29.544873][ T1046] lock(&dev->addr_list_lock_key#4); [ 29.545863][ T1046] lock(&dev->addr_list_lock_key#3); [ 29.546525][ T1046] [ 29.546525][ T1046] *** DEADLOCK *** [ 29.546525][ T1046] [ 29.547542][ T1046] 5 locks held by ifenslave/1046: [ 29.548196][ T1046] #0: ffff88806044c478 (sb_writers#5){.+.+}, at: vfs_write+0x3bb/0x4a0 [ 29.549248][ T1046] #1: ffff88805af00890 (&of->mutex){+.+.}, at: kernfs_fop_write+0x1cf/0x410 [ 29.550343][ T1046] #2: ffff88805b8b54b0 (kn->count#157){.+.+}, at: kernfs_fop_write+0x1f2/0x410 [ 29.551575][ T1046] #3: ffffffffaecf4cf0 (rtnl_mutex){+.+.}, at: bond_opt_tryset_rtnl+0x5f/0xf0 [bonding] [ 29.552819][ T1046] #4: ffff8880460f2280 (&dev->addr_list_lock_key#4){+...}, at: bond_enslave+0x4482/0x47b0 [bonding] [ 29.554175][ T1046] [ 29.554175][ T1046] stack backtrace: [ 29.554907][ T1046] CPU: 0 PID: 1046 Comm: ifenslave Not tainted 5.5.0+ #322 [ 29.555854][ T1046] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 29.557064][ T1046] Call Trace: [ 29.557504][ T1046] dump_stack+0x96/0xdb [ 29.558054][ T1046] check_noncircular+0x371/0x450 [ 29.558723][ T1046] ? print_circular_bug.isra.35+0x310/0x310 [ 29.559486][ T1046] ? hlock_class+0x130/0x130 [ 29.560100][ T1046] ? __lock_acquire+0x2d8d/0x3de0 [ 29.560761][ T1046] __lock_acquire+0x2d8d/0x3de0 [ 29.561366][ T1046] ? register_lock_class+0x14d0/0x14d0 [ 29.562045][ T1046] ? find_held_lock+0x39/0x1d0 [ 29.562641][ T1046] lock_acquire+0x164/0x3b0 [ 29.563199][ T1046] ? dev_mc_sync_multiple+0x95/0x120 [ 29.563872][ T1046] _raw_spin_lock+0x30/0x70 [ 29.564464][ T1046] ? dev_mc_sync_multiple+0x95/0x120 [ 29.565146][ T1046] dev_mc_sync_multiple+0x95/0x120 [ 29.565793][ T1046] bond_enslave+0x448d/0x47b0 [bonding] [ 29.566487][ T1046] ? bond_update_slave_arr+0x940/0x940 [bonding] [ 29.567279][ T1046] ? bstr_printf+0xc20/0xc20 [ 29.567857][ T1046] ? stack_trace_consume_entry+0x160/0x160 [ 29.568614][ T1046] ? deactivate_slab.isra.77+0x2c5/0x800 [ 29.569320][ T1046] ? check_chain_key+0x236/0x5d0 [ 29.569939][ T1046] ? sscanf+0x93/0xc0 [ 29.570442][ T1046] ? vsscanf+0x1e20/0x1e20 [ 29.571003][ T1046] bond_option_slaves_set+0x1a3/0x370 [bonding] [ ... ] Fixes: ab92d68fc22f ("net: core: add generic lockdep keys") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16NFC: pn544: Fix a typo in a debug messageChristophe JAILLET1-1/+1
The ending character of the string shoulb be \n, not \b. Fixes: 17936b43f0fd ("NFC: Standardize logging style") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16ethtool: fix application of verbose no_mask bitsetMichal Kubecek1-0/+3
A bitset without mask in a _SET request means we want exactly the bits in the bitset to be set. This works correctly for compact format but when verbose format is parsed, ethnl_update_bitset32_verbose() only sets the bits present in the request bitset but does not clear the rest. This can cause incorrect results like lion:~ # ethtool eth0 | grep Wake Supports Wake-on: pumbg Wake-on: g lion:~ # ethtool -s eth0 wol u lion:~ # ethtool eth0 | grep Wake Supports Wake-on: pumbg Wake-on: ug when the second ethtool command issues request ETHTOOL_MSG_WOL_SET ETHTOOL_A_WOL_HEADER ETHTOOL_A_HEADER_DEV_NAME = "eth0" ETHTOOL_A_WOL_MODES ETHTOOL_A_BITSET_NOMASK ETHTOOL_A_BITSET_BITS ETHTOOL_A_BITSET_BITS_BIT ETHTOOL_BITSET_BIT_INDEX = 1 Fix the logic by clearing the whole target bitmap before we start iterating through the request bits. Fixes: 10b518d4e6dd ("ethtool: netlink bitset handling") Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: dsa: b53: Ensure the default VID is untaggedFlorian Fainelli1-0/+3
We need to ensure that the default VID is untagged otherwise the switch will be sending tagged frames and the results can be problematic. This is especially true with b53 switches that use VID 0 as their default VLAN since VID 0 has a special meaning. Fixes: fea83353177a ("net: dsa: b53: Fix default VLAN ID") Fixes: 061f6a505ac3 ("net: dsa: Add ndo_vlan_rx_{add, kill}_vid implementation") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16wireguard: socket: remove extra call to synchronize_netJason A. Donenfeld1-1/+0
synchronize_net() is a wrapper around synchronize_rcu(), so there's no point in having synchronize_net and synchronize_rcu back to back, despite the documentation comment suggesting maybe it's somewhat useful, "Wait for packets currently being received to be done." This commit removes the extra call. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16wireguard: send: account for mtu=0 devicesJason A. Donenfeld2-8/+15
It turns out there's an easy way to get packets queued up while still having an MTU of zero, and that's via persistent keep alive. This commit makes sure that in whatever condition, we don't wind up dividing by zero. Note that an MTU of zero for a wireguard interface is something quasi-valid, so I don't think the correct fix is to limit it via min_mtu. This can be reproduced easily with: ip link add wg0 type wireguard ip link add wg1 type wireguard ip link set wg0 up mtu 0 ip link set wg1 up wg set wg0 private-key <(wg genkey) wg set wg1 listen-port 1 private-key <(wg genkey) peer $(wg show wg0 public-key) wg set wg0 peer $(wg show wg1 public-key) persistent-keepalive 1 endpoint 127.0.0.1:1 However, while min_mtu=0 seems fine, it makes sense to restrict the max_mtu. This commit also restricts the maximum MTU to the greatest number for which rounding up to the padding multiple won't overflow a signed integer. Packets this large were always rejected anyway eventually, due to checks deeper in, but it seems more sound not to even let the administrator configure something that won't work anyway. We use this opportunity to clean up this function a bit so that it's clear which paths we're expecting. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16wireguard: receive: reset last_under_load to zeroJason A. Donenfeld1-2/+5
This is a small optimization that prevents more expensive comparisons from happening when they are no longer necessary, by clearing the last_under_load variable whenever we wind up in a state where we were under load but we no longer are. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Suggested-by: Matt Dunwoodie <ncon@noconroy.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16wireguard: selftests: reduce complexity and fix make racesJason A. Donenfeld1-24/+14
This gives us fewer dependencies and shortens build time, fixes up some hash checking race conditions, and also fixes missing directory creation that caused issues on massively parallel builds. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16mptcp: Protect subflow socket options before connection completesMat Martineau1-29/+19
Userspace should not be able to directly manipulate subflow socket options before a connection is established since it is not yet known if it will be an MPTCP subflow or a TCP fallback subflow. TCP fallback subflows can be more directly controlled by userspace because they are regular TCP connections, while MPTCP subflow sockets need to be configured for the specific needs of MPTCP. Use the same logic as sendmsg/recvmsg to ensure that socket option calls are only passed through to known TCP fallback subflows. Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: phy: restore mdio regs in the iproc mdio driverArun Parameswaran1-0/+20
The mii management register in iproc mdio block does not have a retention register so it is lost on suspend. Save and restore value of register while resuming from suspend. Fixes: bb1a619735b4 ("net: phy: Initialize mdio clock at probe function") Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com> Signed-off-by: Scott Branden <scott.branden@broadcom.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: add strict checks in netdev_name_node_alt_destroy()Eric Dumazet1-0/+6
netdev_name_node_alt_destroy() does a lookup over all device names of a namespace. We need to make sure the name belongs to the device of interest, and that we do not destroy its primary name, since we rely on it being not deleted : dev->name_node would indeed point to freed memory. syzbot report was the following : BUG: KASAN: use-after-free in dev_net include/linux/netdevice.h:2206 [inline] BUG: KASAN: use-after-free in mld_force_mld_version net/ipv6/mcast.c:1172 [inline] BUG: KASAN: use-after-free in mld_in_v2_mode_only net/ipv6/mcast.c:1180 [inline] BUG: KASAN: use-after-free in mld_in_v1_mode+0x203/0x230 net/ipv6/mcast.c:1190 Read of size 8 at addr ffff88809886c588 by task swapper/1/0 CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.6.0-rc1-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x197/0x210 lib/dump_stack.c:118 print_address_description.constprop.0.cold+0xd4/0x30b mm/kasan/report.c:374 __kasan_report.cold+0x1b/0x32 mm/kasan/report.c:506 kasan_report+0x12/0x20 mm/kasan/common.c:641 __asan_report_load8_noabort+0x14/0x20 mm/kasan/generic_report.c:135 dev_net include/linux/netdevice.h:2206 [inline] mld_force_mld_version net/ipv6/mcast.c:1172 [inline] mld_in_v2_mode_only net/ipv6/mcast.c:1180 [inline] mld_in_v1_mode+0x203/0x230 net/ipv6/mcast.c:1190 mld_send_initial_cr net/ipv6/mcast.c:2083 [inline] mld_dad_timer_expire+0x24/0x230 net/ipv6/mcast.c:2118 call_timer_fn+0x1ac/0x780 kernel/time/timer.c:1404 expire_timers kernel/time/timer.c:1449 [inline] __run_timers kernel/time/timer.c:1773 [inline] __run_timers kernel/time/timer.c:1740 [inline] run_timer_softirq+0x6c3/0x1790 kernel/time/timer.c:1786 __do_softirq+0x262/0x98c kernel/softirq.c:292 invoke_softirq kernel/softirq.c:373 [inline] irq_exit+0x19b/0x1e0 kernel/softirq.c:413 exiting_irq arch/x86/include/asm/apic.h:546 [inline] smp_apic_timer_interrupt+0x1a3/0x610 arch/x86/kernel/apic/apic.c:1146 apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:829 </IRQ> RIP: 0010:native_safe_halt+0xe/0x10 arch/x86/include/asm/irqflags.h:61 Code: 68 73 c5 f9 eb 8a cc cc cc cc cc cc e9 07 00 00 00 0f 00 2d 94 be 59 00 f4 c3 66 90 e9 07 00 00 00 0f 00 2d 84 be 59 00 fb f4 <c3> cc 55 48 89 e5 41 57 41 56 41 55 41 54 53 e8 de 2a 74 f9 e8 09 RSP: 0018:ffffc90000d3fd68 EFLAGS: 00000282 ORIG_RAX: ffffffffffffff13 RAX: 1ffffffff136761a RBX: ffff8880a99fc340 RCX: 0000000000000000 RDX: dffffc0000000000 RSI: 0000000000000006 RDI: ffff8880a99fcbd4 RBP: ffffc90000d3fd98 R08: ffff8880a99fc340 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: dffffc0000000000 R13: ffffffff8aa5a1c0 R14: 0000000000000000 R15: 0000000000000001 arch_cpu_idle+0xa/0x10 arch/x86/kernel/process.c:686 default_idle_call+0x84/0xb0 kernel/sched/idle.c:94 cpuidle_idle_call kernel/sched/idle.c:154 [inline] do_idle+0x3c8/0x6e0 kernel/sched/idle.c:269 cpu_startup_entry+0x1b/0x20 kernel/sched/idle.c:361 start_secondary+0x2f4/0x410 arch/x86/kernel/smpboot.c:264 secondary_startup_64+0xa4/0xb0 arch/x86/kernel/head_64.S:242 Allocated by task 10229: save_stack+0x23/0x90 mm/kasan/common.c:72 set_track mm/kasan/common.c:80 [inline] __kasan_kmalloc mm/kasan/common.c:515 [inline] __kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:488 kasan_kmalloc+0x9/0x10 mm/kasan/common.c:529 __do_kmalloc_node mm/slab.c:3616 [inline] __kmalloc_node+0x4e/0x70 mm/slab.c:3623 kmalloc_node include/linux/slab.h:578 [inline] kvmalloc_node+0x68/0x100 mm/util.c:574 kvmalloc include/linux/mm.h:645 [inline] kvzalloc include/linux/mm.h:653 [inline] alloc_netdev_mqs+0x98/0xe40 net/core/dev.c:9797 rtnl_create_link+0x22d/0xaf0 net/core/rtnetlink.c:3047 __rtnl_newlink+0xf9f/0x1790 net/core/rtnetlink.c:3309 rtnl_newlink+0x69/0xa0 net/core/rtnetlink.c:3377 rtnetlink_rcv_msg+0x45e/0xaf0 net/core/rtnetlink.c:5438 netlink_rcv_skb+0x177/0x450 net/netlink/af_netlink.c:2477 rtnetlink_rcv+0x1d/0x30 net/core/rtnetlink.c:5456 netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline] netlink_unicast+0x59e/0x7e0 net/netlink/af_netlink.c:1328 netlink_sendmsg+0x91c/0xea0 net/netlink/af_netlink.c:1917 sock_sendmsg_nosec net/socket.c:652 [inline] sock_sendmsg+0xd7/0x130 net/socket.c:672 __sys_sendto+0x262/0x380 net/socket.c:1998 __do_compat_sys_socketcall net/compat.c:771 [inline] __se_compat_sys_socketcall net/compat.c:719 [inline] __ia32_compat_sys_socketcall+0x530/0x710 net/compat.c:719 do_syscall_32_irqs_on arch/x86/entry/common.c:337 [inline] do_fast_syscall_32+0x27b/0xe16 arch/x86/entry/common.c:408 entry_SYSENTER_compat+0x70/0x7f arch/x86/entry/entry_64_compat.S:139 Freed by task 10229: save_stack+0x23/0x90 mm/kasan/common.c:72 set_track mm/kasan/common.c:80 [inline] kasan_set_free_info mm/kasan/common.c:337 [inline] __kasan_slab_free+0x102/0x150 mm/kasan/common.c:476 kasan_slab_free+0xe/0x10 mm/kasan/common.c:485 __cache_free mm/slab.c:3426 [inline] kfree+0x10a/0x2c0 mm/slab.c:3757 __netdev_name_node_alt_destroy+0x1ff/0x2a0 net/core/dev.c:322 netdev_name_node_alt_destroy+0x57/0x80 net/core/dev.c:334 rtnl_alt_ifname net/core/rtnetlink.c:3518 [inline] rtnl_linkprop.isra.0+0x575/0x6f0 net/core/rtnetlink.c:3567 rtnl_dellinkprop+0x46/0x60 net/core/rtnetlink.c:3588 rtnetlink_rcv_msg+0x45e/0xaf0 net/core/rtnetlink.c:5438 netlink_rcv_skb+0x177/0x450 net/netlink/af_netlink.c:2477 rtnetlink_rcv+0x1d/0x30 net/core/rtnetlink.c:5456 netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline] netlink_unicast+0x59e/0x7e0 net/netlink/af_netlink.c:1328 netlink_sendmsg+0x91c/0xea0 net/netlink/af_netlink.c:1917 sock_sendmsg_nosec net/socket.c:652 [inline] sock_sendmsg+0xd7/0x130 net/socket.c:672 ____sys_sendmsg+0x753/0x880 net/socket.c:2343 ___sys_sendmsg+0x100/0x170 net/socket.c:2397 __sys_sendmsg+0x105/0x1d0 net/socket.c:2430 __compat_sys_sendmsg net/compat.c:642 [inline] __do_compat_sys_sendmsg net/compat.c:649 [inline] __se_compat_sys_sendmsg net/compat.c:646 [inline] __ia32_compat_sys_sendmsg+0x7a/0xb0 net/compat.c:646 do_syscall_32_irqs_on arch/x86/entry/common.c:337 [inline] do_fast_syscall_32+0x27b/0xe16 arch/x86/entry/common.c:408 entry_SYSENTER_compat+0x70/0x7f arch/x86/entry/entry_64_compat.S:139 The buggy address belongs to the object at ffff88809886c000 which belongs to the cache kmalloc-4k of size 4096 The buggy address is located 1416 bytes inside of 4096-byte region [ffff88809886c000, ffff88809886d000) The buggy address belongs to the page: page:ffffea0002621b00 refcount:1 mapcount:0 mapping:ffff8880aa402000 index:0x0 compound_mapcount: 0 flags: 0xfffe0000010200(slab|head) raw: 00fffe0000010200 ffffea0002610d08 ffffea0002607608 ffff8880aa402000 raw: 0000000000000000 ffff88809886c000 0000000100000001 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff88809886c480: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88809886c500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb >ffff88809886c580: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff88809886c600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88809886c680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb Fixes: 36fbf1e52bd3 ("net: rtnetlink: add linkprop commands to add and delete alternative ifnames") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: Jiri Pirko <jiri@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: atlantic: fix out of range usage of active_vlans arrayDmitry Bogdanov1-1/+1
fix static checker warning: drivers/net/ethernet/aquantia/atlantic/aq_filters.c:166 aq_check_approve_fvlan() error: passing untrusted data to 'test_bit()' Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: 7975d2aff5af: ("net: aquantia: add support of rx-vlan-filter offload") Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: atlantic: possible fault in transition to hibernationPavel Belous1-5/+8
during hibernation freeze, aq_nic_stop could be invoked on a stopped device. That may cause panic on access to not yet allocated vector/ring structures. Add a check to stop device if it is not yet stopped. Similiarly after freeze in hibernation thaw, aq_nic_start could be invoked on a not initialized net device. Result will be the same. Add a check to start device if it is initialized. In our case, this is the same as started. Fixes: 8aaa112a57c1 ("net: atlantic: refactoring pm logic") Signed-off-by: Pavel Belous <pbelous@marvell.com> Signed-off-by: Nikita Danilov <ndanilov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: atlantic: fix potential error handlingPavel Belous1-1/+3
Code inspection found that in case of mapping error we do return current 'ret' value. But beside error, it is used to count number of descriptors allocated for the packet. In that case map_skb function could return '1'. Changing it to return zero (number of mapped descriptors for skb) Fixes: 018423e90bee ("net: ethernet: aquantia: Add ring support code") Signed-off-by: Pavel Belous <pbelous@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: atlantic: fix use after free kasan warnPavel Belous2-6/+5
skb->len is used to calculate statistics after xmit invocation. Under a stress load it may happen that skb will be xmited, rx interrupt will come and skb will be freed, all before xmit function is even returned. Eventually, skb->len will access unallocated area. Moving stats calculation into tx_clean routine. Fixes: 018423e90bee ("net: ethernet: aquantia: Add ring support code") Reported-by: Christophe Vu-Brugier <cvubrugier@fastmail.fm> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Pavel Belous <pbelous@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: atlantic: better loopback mode handlingNikita Danilov2-5/+13
Add checks to not enable multiple loopback modes simultaneously, It was also discovered that for dma loopback to function correctly promisc mode should be enabled on device. Fixes: ea4b4d7fc106 ("net: atlantic: loopback tests via private flags") Signed-off-by: Nikita Danilov <ndanilov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: atlantic: ptp gpio adjustmentsEgor Pomozov3-1/+17
Clock adjustment data should be passed to FW as well, otherwise in some cases a drift was observed when using GPIO features. Signed-off-by: Egor Pomozov <epomozov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: atlantic: check rpc result and wait for rpc addressIgor Russkikh1-2/+17
Artificial HW reliability tests revealed a possible hangup in the driver. Normally, when device disappears from bus, all register reads returns 0xFFFFFFFF. At remote procedure invocation towards FW there is a logic where result is compared with -1 in a loop. That caused an infinite loop if hardware due to some issues disappears from bus. Add extra result checks to prevent this. Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: atlantic: checksum compat issueDmitry Bezrukov3-4/+7
Yet another checksum offload compatibility issue was found. The known issue is that AQC HW marks tcp packets with 0xFFFF checksum as invalid (1). This is workarounded in driver, passing all the suspicious packets up to the stack for further csum validation. Another HW problem (2) is that it hides invalid csum of LRO aggregated packets inside of the individual descriptors. That was workarounded by forced scan of all LRO descriptors for checksum errors. However the scan logic was joint for both LRO and multi-descriptor packets (jumbos). And this causes the issue. We have to drop LRO packets with the detected bad checksum because of (2), but we have to pass jumbo packets to stack because of (1). When using windows tcp partner with jumbo frames but with LSO disabled driver discards such frames as bad checksummed. But only LRO frames should be dropped, not jumbos. On such a configurations tcp stream have a chance of drops and stucks. (1) 76f254d4afe2 ("net: aquantia: tcp checksum 0xffff being handled incorrectly") (2) d08b9a0a3ebd ("net: aquantia: do not pass lro session with invalid tcp checksum") Fixes: d08b9a0a3ebd ("net: aquantia: do not pass lro session with invalid tcp checksum") Signed-off-by: Dmitry Bezrukov <dbezrukov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16selftests: forwarding: vxlan_bridge_1d: fix tos valueHangbin Liu1-3/+3
After commit 71130f29979c ("vxlan: fix tos value before xmit") we start strict vxlan xmit tos value by RT_TOS(), which limits the tos value less than 0x1E. With current value 0x40 the test will failed with "v1: Expected to capture 10 packets, got 0". So let's choose a smaller tos value for testing. Fixes: d417ecf533fe ("selftests: forwarding: vxlan_bridge_1d: Add a TOS test") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: rtnetlink: fix bugs in rtnl_alt_ifname()Eric Dumazet1-14/+12
Since IFLA_ALT_IFNAME is an NLA_STRING, we have no guarantee it is nul terminated. We should use nla_strdup() instead of kstrdup(), since this helper will make sure not accessing out-of-bounds data. BUG: KMSAN: uninit-value in strlen+0x5e/0xa0 lib/string.c:535 CPU: 1 PID: 19157 Comm: syz-executor.5 Not tainted 5.5.0-rc5-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x1c9/0x220 lib/dump_stack.c:118 kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:118 __msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215 strlen+0x5e/0xa0 lib/string.c:535 kstrdup+0x7f/0x1a0 mm/util.c:59 rtnl_alt_ifname net/core/rtnetlink.c:3495 [inline] rtnl_linkprop+0x85d/0xc00 net/core/rtnetlink.c:3553 rtnl_newlinkprop+0x9d/0xb0 net/core/rtnetlink.c:3568 rtnetlink_rcv_msg+0x1153/0x1570 net/core/rtnetlink.c:5424 netlink_rcv_skb+0x451/0x650 net/netlink/af_netlink.c:2477 rtnetlink_rcv+0x50/0x60 net/core/rtnetlink.c:5442 netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline] netlink_unicast+0xf9e/0x1100 net/netlink/af_netlink.c:1328 netlink_sendmsg+0x1248/0x14d0 net/netlink/af_netlink.c:1917 sock_sendmsg_nosec net/socket.c:639 [inline] sock_sendmsg net/socket.c:659 [inline] ____sys_sendmsg+0x12b6/0x1350 net/socket.c:2330 ___sys_sendmsg net/socket.c:2384 [inline] __sys_sendmsg+0x451/0x5f0 net/socket.c:2417 __do_sys_sendmsg net/socket.c:2426 [inline] __se_sys_sendmsg+0x97/0xb0 net/socket.c:2424 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2424 do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x45b3b9 Code: ad b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007ff1c7b1ac78 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00007ff1c7b1b6d4 RCX: 000000000045b3b9 RDX: 0000000000000000 RSI: 0000000020000040 RDI: 0000000000000003 RBP: 000000000075bf20 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff R13: 00000000000009cb R14: 00000000004cb3dd R15: 000000000075bf2c Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:144 [inline] kmsan_internal_poison_shadow+0x66/0xd0 mm/kmsan/kmsan.c:127 kmsan_slab_alloc+0x8a/0xe0 mm/kmsan/kmsan_hooks.c:82 slab_alloc_node mm/slub.c:2774 [inline] __kmalloc_node_track_caller+0xb40/0x1200 mm/slub.c:4382 __kmalloc_reserve net/core/skbuff.c:141 [inline] __alloc_skb+0x2fd/0xac0 net/core/skbuff.c:209 alloc_skb include/linux/skbuff.h:1049 [inline] netlink_alloc_large_skb net/netlink/af_netlink.c:1174 [inline] netlink_sendmsg+0x7d3/0x14d0 net/netlink/af_netlink.c:1892 sock_sendmsg_nosec net/socket.c:639 [inline] sock_sendmsg net/socket.c:659 [inline] ____sys_sendmsg+0x12b6/0x1350 net/socket.c:2330 ___sys_sendmsg net/socket.c:2384 [inline] __sys_sendmsg+0x451/0x5f0 net/socket.c:2417 __do_sys_sendmsg net/socket.c:2426 [inline] __se_sys_sendmsg+0x97/0xb0 net/socket.c:2424 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2424 do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: 36fbf1e52bd3 ("net: rtnetlink: add linkprop commands to add and delete alternative ifnames") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jiri Pirko <jiri@mellanox.com> Reported-by: syzbot <syzkaller@googlegroups.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: macb: ensure interface is not suspended on at91rm9200Alexandre Belloni1-1/+5
Because of autosuspend, at91ether_start is called with clocks disabled. Ensure that pm_runtime doesn't suspend the interface as soon as it is opened as there is no pm_runtime support is the other relevant parts of the platform support for at91rm9200. Fixes: d54f89af6cc4 ("net: macb: Add pm runtime support") Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: fib_rules: Correctly set table field when table number exceeds 8 bitsJethro Beekman1-1/+1
In 709772e6e06564ed94ba740de70185ac3d792773, RT_TABLE_COMPAT was added to allow legacy software to deal with routing table numbers >= 256, but the same change to FIB rule queries was overlooked. Signed-off-by: Jethro Beekman <jethro@fortanix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net/rds: Track user mapped pages through special APILeon Romanovsky1-12/+12
Convert net/rds to use the newly introduces pin_user_pages() API, which properly sets FOLL_PIN. Setting FOLL_PIN is now required for code that requires tracking of pinned pages. Note that this effectively changes the code's behavior: it now ultimately calls set_page_dirty_lock(), instead of set_page_dirty(). This is probably more accurate. As Christoph Hellwig put it, "set_page_dirty() is only safe if we are dealing with a file backed page where we have reference on the inode it hangs off." [1] [1] https://lore.kernel.org/r/20190723153640.GB720@lst.de Cc: Hans Westgaard Ry <hans.westgaard.ry@oracle.com> Cc: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: John Hubbard <jhubbard@nvidia.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16ipv6: Fix nlmsg_flags when splitting a multipath routeBenjamin Poirier1-0/+1
When splitting an RTA_MULTIPATH request into multiple routes and adding the second and later components, we must not simply remove NLM_F_REPLACE but instead replace it by NLM_F_CREATE. Otherwise, it may look like the netlink message was malformed. For example, ip route add 2001:db8::1/128 dev dummy0 ip route change 2001:db8::1/128 nexthop via fe80::30:1 dev dummy0 \ nexthop via fe80::30:2 dev dummy0 results in the following warnings: [ 1035.057019] IPv6: RTM_NEWROUTE with no NLM_F_CREATE or NLM_F_REPLACE [ 1035.057517] IPv6: NLM_F_CREATE should be set when creating new route This patch makes the nlmsg sequence look equivalent for __ip6_ins_rt() to what it would get if the multipath route had been added in multiple netlink operations: ip route add 2001:db8::1/128 dev dummy0 ip route change 2001:db8::1/128 nexthop via fe80::30:1 dev dummy0 ip route append 2001:db8::1/128 nexthop via fe80::30:2 dev dummy0 Fixes: 27596472473a ("ipv6: fix ECMP route replacement") Signed-off-by: Benjamin Poirier <bpoirier@cumulusnetworks.com> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16ipv6: Fix route replacement with dev-only routeBenjamin Poirier2-3/+10
After commit 27596472473a ("ipv6: fix ECMP route replacement") it is no longer possible to replace an ECMP-able route by a non ECMP-able route. For example, ip route add 2001:db8::1/128 via fe80::1 dev dummy0 ip route replace 2001:db8::1/128 dev dummy0 does not work as expected. Tweak the replacement logic so that point 3 in the log of the above commit becomes: 3. If the new route is not ECMP-able, and no matching non-ECMP-able route exists, replace matching ECMP-able route (if any) or add the new route. We can now summarize the entire replace semantics to: When doing a replace, prefer replacing a matching route of the same "ECMP-able-ness" as the replace argument. If there is no such candidate, fallback to the first route found. Fixes: 27596472473a ("ipv6: fix ECMP route replacement") Signed-off-by: Benjamin Poirier <bpoirier@cumulusnetworks.com> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16selftests: forwarding: use proto icmp for {gretap, ip6gretap}_mac testingHangbin Liu1-12/+13
For tc ip_proto filter, when we extract the flow via __skb_flow_dissect() without flag FLOW_DISSECTOR_F_STOP_AT_ENCAP, we will continue extract to the inner proto. So for GRE + ICMP messages, we should not track GRE proto, but inner ICMP proto. For test mirror_gre.sh, it may make user confused if we capture ICMP message on $h3(since the flow is GRE message). So I move the capture dev to h3-gt{4,6}, and only capture ICMP message. Before the fix: ]# ./mirror_gre.sh TEST: ingress mirror to gretap (skip_hw) [ OK ] TEST: egress mirror to gretap (skip_hw) [ OK ] TEST: ingress mirror to ip6gretap (skip_hw) [ OK ] TEST: egress mirror to ip6gretap (skip_hw) [ OK ] TEST: ingress mirror to gretap: envelope MAC (skip_hw) [FAIL] Expected to capture 10 packets, got 0. TEST: egress mirror to gretap: envelope MAC (skip_hw) [FAIL] Expected to capture 10 packets, got 0. TEST: ingress mirror to ip6gretap: envelope MAC (skip_hw) [FAIL] Expected to capture 10 packets, got 0. TEST: egress mirror to ip6gretap: envelope MAC (skip_hw) [FAIL] Expected to capture 10 packets, got 0. TEST: two simultaneously configured mirrors (skip_hw) [ OK ] WARN: Could not test offloaded functionality After fix: ]# ./mirror_gre.sh TEST: ingress mirror to gretap (skip_hw) [ OK ] TEST: egress mirror to gretap (skip_hw) [ OK ] TEST: ingress mirror to ip6gretap (skip_hw) [ OK ] TEST: egress mirror to ip6gretap (skip_hw) [ OK ] TEST: ingress mirror to gretap: envelope MAC (skip_hw) [ OK ] TEST: egress mirror to gretap: envelope MAC (skip_hw) [ OK ] TEST: ingress mirror to ip6gretap: envelope MAC (skip_hw) [ OK ] TEST: egress mirror to ip6gretap: envelope MAC (skip_hw) [ OK ] TEST: two simultaneously configured mirrors (skip_hw) [ OK ] WARN: Could not test offloaded functionality Fixes: ba8d39871a10 ("selftests: forwarding: Add test for mirror to gretap") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: Petr Machata <pmachata@gmail.com> Tested-by: Petr Machata <pmachata@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-14netdevice.h: fix all kernel-doc and Sphinx warningsRandy Dunlap1-1/+15
Eliminate all kernel-doc and Sphinx warnings in <linux/netdevice.h>. Fixes these warnings: ../include/linux/netdevice.h:2100: warning: Function parameter or member 'gso_partial_features' not described in 'net_device' ../include/linux/netdevice.h:2100: warning: Function parameter or member 'l3mdev_ops' not described in 'net_device' ../include/linux/netdevice.h:2100: warning: Function parameter or member 'xfrmdev_ops' not described in 'net_device' ../include/linux/netdevice.h:2100: warning: Function parameter or member 'tlsdev_ops' not described in 'net_device' ../include/linux/netdevice.h:2100: warning: Function parameter or member 'name_assign_type' not described in 'net_device' ../include/linux/netdevice.h:2100: warning: Function parameter or member 'ieee802154_ptr' not described in 'net_device' ../include/linux/netdevice.h:2100: warning: Function parameter or member 'mpls_ptr' not described in 'net_device' ../include/linux/netdevice.h:2100: warning: Function parameter or member 'xdp_prog' not described in 'net_device' ../include/linux/netdevice.h:2100: warning: Function parameter or member 'gro_flush_timeout' not described in 'net_device' ../include/linux/netdevice.h:2100: warning: Function parameter or member 'xdp_bulkq' not described in 'net_device' ../include/linux/netdevice.h:2100: warning: Function parameter or member 'xps_cpus_map' not described in 'net_device' ../include/linux/netdevice.h:2100: warning: Function parameter or member 'xps_rxqs_map' not described in 'net_device' ../include/linux/netdevice.h:2100: warning: Function parameter or member 'qdisc_hash' not described in 'net_device' ../include/linux/netdevice.h:3552: WARNING: Inline emphasis start-string without end-string. ../include/linux/netdevice.h:3552: WARNING: Inline emphasis start-string without end-string. Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-14net: dsa: tag_ar9331: Make sure there is headroom for tagPer Forlin1-1/+1
Passing tag size to skb_cow_head will make sure there is enough headroom for the tag data. This change does not introduce any overhead in case there is already available headroom for tag. Signed-off-by: Per Forlin <perfn@axis.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-14net: dsa: tag_qca: Make sure there is headroom for tagPer Forlin1-1/+1
Passing tag size to skb_cow_head will make sure there is enough headroom for the tag data. This change does not introduce any overhead in case there is already available headroom for tag. Signed-off-by: Per Forlin <perfn@axis.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-14net, ip6_tunnel: enhance tunnel locate with link checkWilliam Dauchy1-21/+47
With ipip, it is possible to create an extra interface explicitly attached to a given physical interface: # ip link show tunl0 4: tunl0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default qlen 1000 link/ipip 0.0.0.0 brd 0.0.0.0 # ip link add tunl1 type ipip dev eth0 # ip link show tunl1 6: tunl1@eth0: <NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default qlen 1000 link/ipip 0.0.0.0 brd 0.0.0.0 But it is not possible with ip6tnl: # ip link show ip6tnl0 5: ip6tnl0@NONE: <NOARP> mtu 1452 qdisc noop state DOWN mode DEFAULT group default qlen 1000 link/tunnel6 :: brd :: # ip link add ip6tnl1 type ip6tnl dev eth0 RTNETLINK answers: File exists This patch aims to make it possible by adding link comparaison in both tunnel locate and lookup functions; we also modify mtu calculation when attached to an interface with a lower mtu. This permits to make use of x-netns communication by moving the newly created tunnel in a given netns. Signed-off-by: William Dauchy <w.dauchy@criteo.com> Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-14net/smc: no peer ID in CLC decline for SMCDUrsula Braun1-1/+3
Just SMCR requires a CLC Peer ID, but not SMCD. The field should be zero for SMCD. Fixes: c758dfddc1b5 ("net/smc: add SMC-D support in CLC messages") Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-14net/smc: transfer fasync_list in case of fallbackUrsula Braun1-0/+2
SMC does not work together with FASTOPEN. If sendmsg() is called with flag MSG_FASTOPEN in SMC_INIT state, the SMC-socket switches to fallback mode. To handle the previous ioctl FIOASYNC call correctly in this case, it is necessary to transfer the socket wait queue fasync_list to the internal TCP socket. Reported-by: syzbot+4b1fe8105f8044a26162@syzkaller.appspotmail.com Fixes: ee9dfbef02d18 ("net/smc: handle sockopts forcing fallback") Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-14net: hns3: fix a copying IPv6 address error in hclge_fd_get_flow_tuples()Guangbin Huang1-6/+9
The IPv6 address defined in struct in6_addr is specified as big endian, but there is no specified endian in struct hclge_fd_rule_tuples, so it will cause a problem if directly use memcpy() to copy ipv6 address between these two structures since this field in struct hclge_fd_rule_tuples is little endian. This patch fixes this problem by using be32_to_cpu() to convert endian of IPv6 address of struct in6_addr before copying. Fixes: d93ed94fbeaf ("net: hns3: add aRFS support for PF") Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-14net: hns3: fix VF bandwidth does not take effect in some caseYonglong Liu1-1/+1
When enabling 4 TC after setting the bandwidth of VF, the bandwidth of VF will resume to default value, because of the qset resources changed in this case. This patch fixes it by using a fixed VF's qset resources according to HNAE3_MAX_TC macro. Fixes: ee9e44248f52 ("net: hns3: add support for configuring bandwidth of VF on the host") Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-14net: hns3: add management table after IMP resetYufeng Mo1-0/+7
In the current process, the management table is missing after the IMP reset. This patch adds the management table to the reset process. Fixes: f5aac71c0327 ("net: hns3: add manager table initialization for hardware") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-14mac80211: fix wrong 160/80+80 MHz settingShay Bar1-2/+14
Before this patch, STA's would set new width of 160/80+80 MHz based on AP capability only. This is wrong because STA may not support > 80MHz BW. Fix is to verify STA has 160/80+80 MHz capability before increasing its width to > 80MHz. The "support_80_80" and "support_160" setting is based on: "Table 9-272 — Setting of the Supported Channel Width Set subfield and Extended NSS BW Support subfield at a STA transmitting the VHT Capabilities Information field" From "Draft P802.11REVmd_D3.0.pdf" Signed-off-by: Aviad Brikman <aviad.brikman@celeno.com> Signed-off-by: Shay Bar <shay.bar@celeno.com> Link: https://lore.kernel.org/r/20200210130728.23674-1-shay.bar@celeno.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-02-14cfg80211: add missing policy for NL80211_ATTR_STATUS_CODESergey Matyukevich1-0/+1
The nl80211_policy is missing for NL80211_ATTR_STATUS_CODE attribute. As a result, for strictly validated commands, it's assumed to not be supported. Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com> Link: https://lore.kernel.org/r/20200213131608.10541-2-sergey.matyukevich.os@quantenna.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-02-13xfrm: interface: use icmp_ndo_send helperJason A. Donenfeld1-3/+3
Because xfrmi is calling icmp from network device context, it should use the ndo helper so that the rate limiting applies correctly. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Cc: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-13wireguard: device: use icmp_ndo_send helperJason A. Donenfeld2-2/+13
Because wireguard is calling icmp from network device context, it should use the ndo helper so that the rate limiting applies correctly. This commit adds a small test to the wireguard test suite to ensure that the new functions continue doing the right thing in the context of wireguard. It does this by setting up a condition that will definately evoke an icmp error message from the driver, but along a nat'd path. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-13sunvnet: use icmp_ndo_send helperJason A. Donenfeld1-19/+4
Because sunvnet is calling icmp from network device context, it should use the ndo helper so that the rate limiting applies correctly. While we're at it, doing the additional route lookup before calling icmp_ndo_send is superfluous, since this is the job of the icmp code in the first place. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Shannon Nelson <shannon.nelson@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-13gtp: use icmp_ndo_send helperJason A. Donenfeld1-2/+2
Because gtp is calling icmp from network device context, it should use the ndo helper so that the rate limiting applies correctly. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Harald Welte <laforge@gnumonks.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-13icmp: introduce helper for nat'd source address in network device contextJason A. Donenfeld4-0/+79
This introduces a helper function to be called only by network drivers that wraps calls to icmp[v6]_send in a conntrack transformation, in case NAT has been used. We don't want to pollute the non-driver path, though, so we introduce this as a helper to be called by places that actually make use of this, as suggested by Florian. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-13net/sched: flower: add missing validation of TCA_FLOWER_FLAGSDavide Caratti1-0/+1
unlike other classifiers that can be offloaded (i.e. users can set flags like 'skip_hw' and 'skip_sw'), 'cls_flower' doesn't validate the size of netlink attribute 'TCA_FLOWER_FLAGS' provided by user: add a proper entry to fl_policy. Fixes: 5b33f48842fa ("net/flower: Introduce hardware offload support") Signed-off-by: Davide Caratti <dcaratti@redhat.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.