| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The codes add ethtool functions to set RX flows for HW LRO. Because the
HW LRO hardware can only recognize the destination IP of TCP/IP RX flows,
the ethtool command to add HW LRO flow is as below:
ethtool -N [devname] flow-type tcp4 dst-ip [ip_addr] loc [0~1]
Otherwise, cause the hardware can set total four destination IPs, each
GMAC (GMAC1/GMAC2) can set two IPs separately at most.
Signed-off-by: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The codes add the large receive offload (LRO) functions by hardware as below:
1) PDMA has total four RX rings that one is the normal ring, and others can
be configured as LRO rings.
2) Only TCP/IP RX flows can be offloaded. The hardware can set four IP
addresses at most, if the destination IP of the RX flow matches one of
them, it has the chance to be offloaded.
3) There three RX flows can be offloaded at most, and one flow is mapped to
one RX ring.
4) If there are more than three candidate RX flows, the hardware can
choose three of them by throughput comparison results.
Signed-off-by: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device table is required to load modules based on
modaliases. After adding MODULE_DEVICE_TABLE, below entries
for example will be added to modules.alias:
alias of:N*T*Cmediatek,mt7623-ethC* mtk_eth_soc
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
add the protection of the race condition between
the reset process and hardware access happening
on the related callbacks.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
struct mtk_eth has already contained struct regmap ethsys pointer
to the address range of the internal circuit reset, so we reuse it
to reset more internal blocks on ethernet hardware such as packet
processing engine (PPE) and frame engine (FE) instead of rstc which
deals with FE only.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1) original driver only resets DMA used by descriptor rings
which can't guarantee it can recover all various kinds of fatal
errors, so the patch tries to reset the underlying hardware
resource from scratch on Mediatek SoC required for ethernet
running, including power, pin mux control, clock and internal
circuits on the ethernet in order to restore into the initial
state which the rebooted machine gives.
2) add state variable inside structure mtk_eth to help distinguish
mtk_hw_init is called between the initialization during boot time
or re-initialization during the reset process.
3) add ge_mode variable inside structure mtk_mac for restoring
the interface mode of the current setup for the target MAC.
4) remove __init attribute from mtk_hw_init definition
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
introduce power domain control which the digital circuit of
the ethernet belongs to inside the flow of hardware initialization
and deinitialization which helps the entire ethernet hardware block
could restart cleanly and completely as being back to the initial
state when the whole machine reboot.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This cleans up the error path inside mtk_hw_init call, causing it able
to exit appropriately when something fails and also includes refactoring
mtk_cleanup call to make the partial logic reusable on the error path.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
grouping things related to the deinitialization of what
mtk_hw_init call does that help to be reused by the reset
process and the error path handling.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
the existing mtk_hw_init includes hardware and software
initialization inside so that it is slightly hard to reuse
them for the process of the reset recovery, so some splitting
is made here for keeping hardware initializing relevant thing
and the else such as IRQ registration and MDIO initialization
what are all about to the interface of core driver moved to the
other proper place because they have no needs to register IRQ and
re-initialize structure again during the reset process.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch adds support for aggregating more SKBs feed into NAPI in
order to get more benefits from generic receive offload (GRO) by
peeking at the RX ring status and moving more packets right before
returning from NAPI RX polling handler if NAPI budgets are still
available and some packets already present in hardware.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch makes move wmb() to outside the loop that could help
RX path handling more faster although that RX descriptors aren't
freed for DMA to use as soon as possible, but based on my experiment
and the result shows it still can reach about 943Mbpis without
performance drop that is tested based on the setup with one port
using Giga PHY and 256 RX descriptors for DMA to move.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Return -ENODEV if the MDIO bus is disabled in the device tree.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
a lot of parts in the driver uses devm_* APIs to gain benefits from the
device resource management, so devm_mdiobus_alloc is also used instead
of mdiobus_alloc to have more elegant code flow.
Using common code provided by the devm_* helps to
1) have simplified the code flow as [1] says
2) decrease the risk of incorrect error handling by human
3) only a few drivers used it since it was proposed on linux 3.16,
so just hope to promote for this.
Ref:
[1] https://patchwork.ozlabs.org/patch/344093/
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the missing of_node_put() after finishing the usage
of of_get_child_by_name.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mtk_stop() must be called to stop for freeing DMA
resources acquired and restoring state changed by mtk_open()
firstly when module removal.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
original mdio_cleanup is not in the symmetric place against where
mdio_init is, so relocate mdio_cleanup to the right one.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
these irqs are not used for shared irq and disabled during ethernet stops.
irq requested by devm_request_irq is safe to be freed automatically on
driver detach.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
use skb_free_frag() instead of legacy put_page()
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1) If the return value of devm_clk_get is EPROBE_DEFER, we should
defer probing the driver. The change is verified and works based
on 4.8-rc1 staying with the latest clk-next code for MT7623.
2) Changing with the usage of loops to work out if all clocks
required are fine
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
which net device the SKB is complete for depends on the forward port
on txd4 on the corresponding TX descriptor, but the information isn't
set up well in case of SKB fragments that would lead to watchdog timeout
from the upper layer, so fix it up.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops. These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };
@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;
@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct ethtool_ops i = { ... };
// </smpl>
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Because we change to use the PDMA as the Ethernet RX DMA engine,
the patch modifies to set GDM to send packets to PDMA for RX.
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Because the PDMA has richer features than the QDMA for Ethernet RX
(such as multiple RX rings, HW LRO, etc.),
the patch modifies to use the PDMA to handle Ethernet RX.
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor overlapping changes for both merge conflicts.
Resolution work done by Stephen Rothwell was used
as a reference.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Runtime warning occurs if DMA-API debug feature is enabled that would be
raised by pointers passed to DMA API as arguments to inconsistent struct
device objects, so that the patch makes them usage aligned between DMA
operations such as dma_map_*() and dma_unmap_*() to eliminate the warning.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 08ef55c6f257acf3bdc6940813f80e8f0f5d90ec
("net-next: mediatek: fix gigabit and flow control advertisement")
had supported proper flow control settings for GMAC1. But for GMAC0,
1.GMAC0 shares the common logic with GMAC1 inside mtk_phy_link_adjust()
to adapt various settings for the target phy.
2.GMAC0 uses fixed-phy to connect to a builtin gigabit switch with
fixed link speed as commit 0c72c50f6f93b0c3daa9ea35d89ab3a933c7b5a0
("net-next: mediatek: add fixed-phy support") describes.
3.However, fixed-phy doesn't enable SUPPORTED_Pause & SUPPORTED_Asym_Pause
supported flag on default that would cause mtk_phy_link_adjust() not to
enable flow control setting on GMAC0 properly and cause packet dropped
when high traffic.
Due to these reasons, the patch adds SUPPORTED_Pause & SUPPORTED_Asym_Pause
supported flags on fixed-phy used by the driver to have proper handling on
the both GMAC with the shared common logic.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch fixes up the incorrect setup of reduced MII (RMII) on GMAC
and adds the supplement for the setup of reverse MII (REVMII) on GMAC
, and rearranges the error handling for invalid PHY argument.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the missing of_node_put() after finishing the usage
of of_parse_phandle() or of_node_get() used by fixed_phy.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To fix runtime warning with lockdep is enabled due that u64_stats_sync
is not initialized well, so add it.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since these critical sections protected by page_lock are all entered
from the user context or bottom half context, they can be replaced
with the spin_lock() or spin_lock_bh instead of spin_lock_irqsave().
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes the following sparse warnings:
drivers/net/ethernet/mediatek/mtk_eth_soc.c:79:5: warning:
symbol '_mtk_mdio_write' was not declared. Should it be static?
drivers/net/ethernet/mediatek/mtk_eth_soc.c:98:5: warning:
symbol '_mtk_mdio_read' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove .owner field since calls to module_platform_driver() will
set it automatically.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 8067302973a1 ("net-next: mediatek: add support for IRQ grouping")
adds handling for irq 1 and 2 to the uninit function but did not remove
irq 0 which is not used since irq grouping was introduced. Fix this by
removing the superfluous call to free_irq().
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: John Crispin <john@phrozen.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 8067302973a1 ("net-next: mediatek: add support for IRQ grouping")
failed to properly update the irq handling inside mtk_poll_controller()
causing compile errors if netconsole was enabled. Fix this by updating
the code to use the new separated irq handler function for RX.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ethernet core has 3 IRQs. Using the IRQ grouping registers we are able
to separate TX and RX IRQs, which allows us to service them on separate
cores. This patch splits the IRQ handler into 2 separate functions, one for
TX and another for RX. The TX housekeeping is split out into its own NAPI
handler.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code that enables and disables IRQs is missing proper locking. After
adding the IRQ grouping patch and routing the RX and TX IRQs to different
cores we experienced IRQ stalls. Fix this by adding proper locking.
We use a dedicated lock to reduce the latency if the IRQ code.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code currently uses variables to store and never modify the bit masks
of interrupts. This is legacy code from an early version of the driver
that supported MIPS based SoCs where the IRQ bits depended on the actual
SoC. As the bits are the same for all ARM based SoCs using this driver we
can remove the intermediate variables.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver was originally written for MIPS based SoC. These required the
IRQ mask register to be read after writing it to ensure that the content
was actually applied. As this version only works on ARM based SoCs, we can
safely remove the 2 reads as they are no longer required.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code checks if the queue should be stopped because we are below the
threshold of free descriptors only to check if it should be started again.
If we do end up in a state where we are at the threshold limit, it makes
more sense to just stop the queue and wait for the next IRQ to trigger the
TX housekeeping again. There is no rush in enqueuing the next packet, it
needs to wait for all the others in the queue to be dispatched first
anyway.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current code unconditionally wakes up the queue at the end of each
tx_poll action. Change the code to only wake up the queues if any of
them have actually been stopped before.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TX ring setup has an off by one error causing it to not utilise all
descriptors. This has the side effect that we need to reset the next
pointer at runtime to make it work. Fix the off by one and remove the
code fixing the ring at runtime.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During stress testing, after reducing the threshold value, we have seen
TX timeouts that were caused by the watchdog_timeo value being too low.
Increase the value to 5 * HZ which is a value commonly used by many other
drivers.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The logic to calculate the threshold value for stopping the TX queue is
bad. Currently it will always use 1/2 of the rings size, which is way too
much. Set the threshold to MAX_SKB_FRAGS. This makes sure that the queue
is stopped when there is not enough room to accept an additional segment.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current code only disables those IRQs that we will later use. To
ensure that we have a predefined state, we really want to disable all IRQs.
Change the code to disable all IRQs to achieve this.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The QDMA engine can fail to update the register pointing to the next TX
descriptor if this bit does not get set in the QDMA configuration register.
Not setting this bit can result in invalid values inside the TX rings
registers which will causes TX stalls.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two places inside mtk_poll_rx where rx_dropped is not being
incremented properly. Fix this by adding the missing code to increment
the counter.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The lookup of the tx_buffer in the error path inside mtk_tx_map() uses the
wrong descriptor pointer. This looks like a copy & paste error. Change the
code to use the correct pointer.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Nelson Chang
Sean Wang
David S. Miller
Julia Lawall
Wei Yongjun
Wei Yongjun
John Crispin