| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When lag is active, which is controlled by the bonded mlx5e netdev, mlx5
interface unregestering must happen in the reverse order where rdma is
unregistered (unloaded) first, to guarantee all references to the lag
context in hardware is removed, then remove mlx5e netdev interface which
will cleanup the lag context from hardware.
Without this fix during destroy of LAG interface, we observed following
errors:
* mlx5_cmd_check:752:(pid 12556): DESTROY_LAG(0x843) op_mod(0x0) failed,
status bad parameter(0x3), syndrome (0xe4ac33)
* mlx5_cmd_check:752:(pid 12556): DESTROY_LAG(0x843) op_mod(0x0) failed,
status bad parameter(0x3), syndrome (0xa5aee8).
Fixes: a31208b1e11d ("net/mlx5_core: New init and exit flow for mlx5_core")
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Mark Zhang <markz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Misc updates from mlx5-next branch:
1) Add the required HW definitions and structures for upcoming TLS
support.
2) Add support for MCQI and MCQS hardware registers for fw version query.
3) Added hardware bits and structures definitions for sub-functions
4) Small code cleanup and improvement for PF pci driver.
5) Bluefield (ECPF) updates and refactoring for better E-Switch
management on ECPF embedded CPU NIC:
5.1) Consolidate querying eswitch number of VFs
5.2) Register event handler at the correct E-Switch init stage
5.3) Setup PF's inline mode and vlan pop when the ECPF is the
E-Swtich manager ( the host PF is basically a VF ).
5.4) Handle Vport UC address changes in switchdev mode.
6) Cleanup the rep and netdev reference when unloading IB rep.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
i# All conflicts fixed but you are still merging.
|
|
As mlx5_get_next_phys_dev is used only for PCI PF devices use case,
limit it to search only for PCI devices.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Prior to reloading a device we must first verify that it was not already
removed. Otherwise, the attempt to remove the device will do nothing, and
in that case we will end up proceeding with adding an new device that no
one was expecting to remove, leaving behind used resources such as EQs that
causes a failure to destroy comp EQs and syndrome (0x30f433).
Fix that by making sure that we try to remove and add a device (based on a
protocol) only if the device is already added.
Fixes: c5447c70594b ("net/mlx5: E-Switch, Reload IB interface when switching devlink modes")
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This isn't used anywhere across the mlx5 driver stack,
remove it.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The mlx5_interface->event callback is not used by mlx5e/mlx5_ib anymore.
We totally remove the delayed events logic work around, since with
the dynamic notifier registration API it is not needed anymore, mlx5_ib
can register its notifier and start receiving events exactly at the moment
it is ready to handle them.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This to allow seamless migration to the new notifier chain API, and to
eventually deprecate interfaces dev->event callback.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Use the new generic EQ API to move all ODP RDMA data structures and logic
form mlx5 core driver into mlx5_ib driver.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
|
|
Currently, mlx5_attach_interface does not check for error
after calling intf->attach or intf->add. When these two calls
fails, the client is not initialized and will cause issues such as
kernel panic on invalid address in the teardown path (mlx5_detach_interface)
Fixes: 737a234bb638 ("net/mlx5: Introduce attach/detach to interface API")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The PCI BDF is not unique. PCI domain must also be considered when
searching for the next physical device during lag setup. Example below:
mlx5_core 0000:01:00.0: MLX5E: StrdRq(1) RqSz(8) StrdSz(128) RxCqeCmprss(0)
mlx5_core 0000:01:00.1: MLX5E: StrdRq(1) RqSz(8) StrdSz(128) RxCqeCmprss(0)
mlx5_core 0001:01:00.0: MLX5E: StrdRq(1) RqSz(8) StrdSz(128) RxCqeCmprss(0)
mlx5_core 0001:01:00.1: MLX5E: StrdRq(1) RqSz(8) StrdSz(128) RxCqeCmprss(0)
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Up until this point it wasn't possible to activate IB representors
when switching to switchdev mode, remove this limitation.
We trigger reload of the PF IB interface in order to make sure that
already allocated resources are invalid and new resources will be opened
correctly with all the limitations of switchdev mode applied (only raw
packet capabilities, without RoCE). We also move the remove/add to a
place where the E-Switch mode is set/unset to better control when to
trigger this action, this will allow the IB side to start in the correct
mode.
For better code reuse, create a function which reloads an interface and
export it.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
list_splice_init initializing waiting_events_list after splicing it to
temp list, therefore we should loop over temp list to fire the events.
Fixes: 4ca637a20a52 ("net/mlx5: Delay events till mlx5 interface's add complete for pci resume")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
mlx5_ib_add is called during mlx5_pci_resume after a pci error.
Before mlx5_ib_add completes, there are multiple events which trigger
function mlx5_ib_event. This cause kernel panic because mlx5_ib_event
accesses unitialized resources.
The fix is to extend Erez Shitrit's patch <97834eba7c19>
("net/mlx5: Delay events till ib registration ends") to cover
the pci resume code path.
Trace:
mlx5_core 0001:01:00.6: mlx5_pci_resume was called
mlx5_core 0001:01:00.6: firmware version: 16.20.1011
mlx5_core 0001:01:00.6: mlx5_attach_interface:164:(pid 779):
mlx5_ib_event:2996:(pid 34777): warning: event on port 1
mlx5_ib_event:2996:(pid 34782): warning: event on port 1
Unable to handle kernel paging request for data at address 0x0001c104
Faulting instruction address: 0xd000000008f411fc
Oops: Kernel access of bad area, sig: 11 [#1]
...
...
Call Trace:
[c000000fff77bb70] [d000000008f4119c] mlx5_ib_event+0x64/0x470 [mlx5_ib] (unreliable)
[c000000fff77bc60] [d000000008e67130] mlx5_core_event+0xb8/0x210 [mlx5_core]
[c000000fff77bd10] [d000000008e4bd00] mlx5_eq_int+0x528/0x860[mlx5_core]
Fixes: 97834eba7c19 ("net/mlx5: Delay events till ib registration ends")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When mlx5_ib registers itself to mlx5_core as an interface, it will
call mlx5_add_device which will call mlx5_ib interface add callback,
in case the latter successfully returns, only then mlx5_core will add
it to the interface list and async events will be forwarded to mlx5_ib.
Between mlx5_ib interface add callback and mlx5_core adding the mlx5_ib
interface to its devices list, arriving mlx5_core events can be missed
by the new mlx5_ib registering interface.
In other words:
thread 1: mlx5_ib: mlx5_register_interface(dev)
thread 1: mlx5_core: mlx5_add_device(dev)
thread 1: mlx5_core: ctx = dev->add => (mlx5_ib)->mlx5_ib_add
thread 2: mlx5_core_event: **new event arrives, forward to dev_list
thread 1: mlx5_core: add_ctx_to_dev_list(ctx)
/* previous event was missed by the new interface.*/
It is ok to miss events before dev->add (mlx5_ib)->mlx5_ib_add_device
but not after.
We fix this race by accumulating the events that come between the
ib_register_device (inside mlx5_add_device->(dev->add)) till the adding
to the list completes and fire them to the new registering interface
after that.
Fixes: f1ee87fe55c8 ("net/mlx5: Organize device list API in one place")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
* Update page fault event according to last specification.
* Separate code path for page fault EQ, completion EQ and async EQ.
* Move page fault handling work queue from mlx5_ib static variable
into mlx5_core page fault EQ.
* Allocate memory to store ODP event dynamically as the
events arrive, since in atomic context - use mempool.
* Make mlx5_ib page fault handler run in process context.
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hide the exposed (external) mlx5_dev_list and mlx5_intf_mutex and expose
an organized modular API to manage and manipulate mlx5 devices list.
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Mark Zhang
Saeed Mahameed
Parav Pandit
Alaa Hleihel
Or Gerlitz
Huy Nguyen
Daniel Jurgens
Mark Bloch
Erez Shitrit
Artemy Kovalyov
Mohamad Haj Yahia