Age | Commit message (Collapse) | Author | Files | Lines |
|
Thomas found that some forwarded packets would be stuck
in FQ packet scheduler because their skb->tstamp contained
timestamps far in the future.
We thought we addressed this point in commit 8203e2d844d3
("net: clear skb->tstamp in forwarding paths") but there
is still an issue when/if a packet needs to be fragmented.
In order to meet EDT requirements, we have to make sure all
fragments get the original skb->tstamp.
Note that this original skb->tstamp should be zero in
forwarding path, but might have a non zero value in
output path if user decided so.
Fixes: fb420d5d91c1 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Thomas Bartschies <Thomas.Bartschies@cvk.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The EPHY integrated into the 40nm Set-Top Box devices can falsely
detect energy when connected to a disabled peer interface. When the
peer interface is enabled the EPHY will detect and report the link
as active, but on occasion may get into a state where it is not
able to exchange data with the connected GENET MAC. This issue has
not been observed when the link parameters are auto-negotiated;
however, it has been observed with a manually configured link.
It has been empirically determined that issuing a soft reset to the
EPHY when energy is detected prevents it from getting into this bad
state.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It turns out that the "Workaround for putting the PHY in IDDQ mode"
used by the internal EPHYs on 40nm Set-Top Box chips when powering
down puts the interface to the GENET MAC in a state that can cause
subsequent MAC resets to be incomplete.
Rather than restore the forced soft reset when powering up internal
PHYs, this commit moves the invocation of phy_init_hw earlier in
the MAC initialization sequence to just before the MAC reset in the
open and resume functions. This allows the interface to be stable
and allows the MAC resets to be successful.
The bcmgenet_mii_probe() function is split in two to accommodate
this. The new function bcmgenet_mii_connect() handles the first
half of the functionality before the MAC initialization, and the
bcmgenet_mii_config() function is extended to provide the remaining
PHY configuration following the MAC initialization.
Fixes: 484bfa1507bf ("Revert "net: bcmgenet: Software reset EPHY after power on"")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The internal 40nm EPHYs use a "Workaround for putting the PHY in
IDDQ mode." These PHYs require a soft reset to restore functionality
after they are powered back up.
This commit defines the soft_reset function to use genphy_soft_reset
during phy_init_hw to accommodate this.
Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When commit 28b2e0d2cd13 ("net: phy: remove parameter new_link from
phy_mac_interrupt()") removed the new_link parameter it set the
phydev->link state from the MAC before invoking phy_mac_interrupt().
However, once commit 88d6272acaaa ("net: phy: avoid unneeded MDIO
reads in genphy_read_status") was added this initialization prevents
the proper determination of the connection parameters by the function
genphy_read_status().
This commit removes that initialization to restore the proper
functionality.
Fixes: 88d6272acaaa ("net: phy: avoid unneeded MDIO reads in genphy_read_status")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The increase_address_space() function has to check the PM_LEVEL_SIZE()
condition again under the domain->lock to avoid a false trigger of the
WARN_ON_ONCE() and to avoid that the address space is increase more
often than necessary.
Reported-by: Qian Cai <cai@lca.pw>
Fixes: 754265bcab78 ("iommu/amd: Fix race in increase_address_space()")
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
In the current code, the nvme is using a fixed 4k PRP entry size,
but if the kernel use a page size which is more than 4k, we should
consider the situation that the bv_offset may be larger than the
dev->ctrl.page_size. Otherwise we may miss setting the prp2 and then
cause the command can't be executed correctly.
Fixes: dff824b2aadb ("nvme-pci: optimize mapping of small single segment requests")
Cc: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
When building with "EXTRA_CFLAGS=-Wall" gcc warns:
arch/x86/boot/compressed/acpi.c:29:30: warning: get_cmdline_acpi_rsdp defined but not used [-Wunused-function]
get_cmdline_acpi_rsdp() is only used when CONFIG_RANDOMIZE_BASE and
CONFIG_MEMORY_HOTREMOVE are both enabled, so any build where one of these
config options is disabled has this issue.
Move the function under the same ifdef guard as the call site.
[ tglx: Add context to the changelog so it becomes useful ]
Fixes: 41fa1ee9c6d6 ("acpi: Ignore acpi_rsdp kernel param when the kernel has been locked down")
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/1569719633-32164-1-git-send-email-zhenzhong.duan@oracle.com
|
|
Michael reported that the x86/hyperv initialization code prints the
following dmesg when running in a VM on Hyper-V:
[ 0.000738] Booting paravirtualized kernel on bare hardware
Let the x86/hyperv initialization code set pv_info.name to "Hyper-V" so
dmesg reports correctly:
[ 0.000172] Booting paravirtualized kernel on Hyper-V
[ tglx: Folded build fix provided by Yue ]
Reported-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Andrea Parri <parri.andrea@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Cc: YueHaibing <yuehaibing@huawei.com>
Link: https://lkml.kernel.org/r/20191015103502.13156-1-parri.andrea@gmail.com
|
|
When enabling KASAN and DEBUG_TEST_DRIVER_REMOVE, I find this KASAN
warning:
[ 20.872057] BUG: KASAN: use-after-free in pcc_data_alloc+0x40/0xb8
[ 20.878226] Read of size 4 at addr ffff00236cdeb684 by task swapper/0/1
[ 20.884826]
[ 20.886309] CPU: 19 PID: 1 Comm: swapper/0 Not tainted 5.4.0-rc1-00009-ge7f7df3db5bf-dirty #289
[ 20.894994] Hardware name: Huawei D06 /D06, BIOS Hisilicon D06 UEFI RC0 - V1.16.01 03/15/2019
[ 20.903505] Call trace:
[ 20.905942] dump_backtrace+0x0/0x200
[ 20.909593] show_stack+0x14/0x20
[ 20.912899] dump_stack+0xd4/0x130
[ 20.916291] print_address_description.isra.9+0x6c/0x3b8
[ 20.921592] __kasan_report+0x12c/0x23c
[ 20.925417] kasan_report+0xc/0x18
[ 20.928808] __asan_load4+0x94/0xb8
[ 20.932286] pcc_data_alloc+0x40/0xb8
[ 20.935938] acpi_cppc_processor_probe+0x4e8/0xb08
[ 20.940717] __acpi_processor_start+0x48/0xb0
[ 20.945062] acpi_processor_start+0x40/0x60
[ 20.949235] really_probe+0x118/0x548
[ 20.952887] driver_probe_device+0x7c/0x148
[ 20.957059] device_driver_attach+0x94/0xa0
[ 20.961231] __driver_attach+0xa4/0x110
[ 20.965055] bus_for_each_dev+0xe8/0x158
[ 20.968966] driver_attach+0x30/0x40
[ 20.972531] bus_add_driver+0x234/0x2f0
[ 20.976356] driver_register+0xbc/0x1d0
[ 20.980182] acpi_processor_driver_init+0x40/0xe4
[ 20.984875] do_one_initcall+0xb4/0x254
[ 20.988700] kernel_init_freeable+0x24c/0x2f8
[ 20.993047] kernel_init+0x10/0x118
[ 20.996524] ret_from_fork+0x10/0x18
[ 21.000087]
[ 21.001567] Allocated by task 1:
[ 21.004785] save_stack+0x28/0xc8
[ 21.008089] __kasan_kmalloc.isra.9+0xbc/0xd8
[ 21.012435] kasan_kmalloc+0xc/0x18
[ 21.015913] pcc_data_alloc+0x94/0xb8
[ 21.019564] acpi_cppc_processor_probe+0x4e8/0xb08
[ 21.024343] __acpi_processor_start+0x48/0xb0
[ 21.028689] acpi_processor_start+0x40/0x60
[ 21.032860] really_probe+0x118/0x548
[ 21.036512] driver_probe_device+0x7c/0x148
[ 21.040684] device_driver_attach+0x94/0xa0
[ 21.044855] __driver_attach+0xa4/0x110
[ 21.048680] bus_for_each_dev+0xe8/0x158
[ 21.052591] driver_attach+0x30/0x40
[ 21.056155] bus_add_driver+0x234/0x2f0
[ 21.059980] driver_register+0xbc/0x1d0
[ 21.063805] acpi_processor_driver_init+0x40/0xe4
[ 21.068497] do_one_initcall+0xb4/0x254
[ 21.072322] kernel_init_freeable+0x24c/0x2f8
[ 21.076667] kernel_init+0x10/0x118
[ 21.080144] ret_from_fork+0x10/0x18
[ 21.083707]
[ 21.085186] Freed by task 1:
[ 21.088056] save_stack+0x28/0xc8
[ 21.091360] __kasan_slab_free+0x118/0x180
[ 21.095445] kasan_slab_free+0x10/0x18
[ 21.099183] kfree+0x80/0x268
[ 21.102139] acpi_cppc_processor_exit+0x1a8/0x1b8
[ 21.106832] acpi_processor_stop+0x70/0x80
[ 21.110917] really_probe+0x174/0x548
[ 21.114568] driver_probe_device+0x7c/0x148
[ 21.118740] device_driver_attach+0x94/0xa0
[ 21.122912] __driver_attach+0xa4/0x110
[ 21.126736] bus_for_each_dev+0xe8/0x158
[ 21.130648] driver_attach+0x30/0x40
[ 21.134212] bus_add_driver+0x234/0x2f0
[ 21.0x10/0x18
[ 21.161764]
[ 21.163244] The buggy address belongs to the object at ffff00236cdeb600
[ 21.163244] which belongs to the cache kmalloc-256 of size 256
[ 21.175750] The buggy address is located 132 bytes inside of
[ 21.175750] 256-byte region [ffff00236cdeb600, ffff00236cdeb700)
[ 21.187473] The buggy address belongs to the page:
[ 21.192254] page:fffffe008d937a00 refcount:1 mapcount:0 mapping:ffff002370c0fa00 index:0x0 compound_mapcount: 0
[ 21.202331] flags: 0x1ffff00000010200(slab|head)
[ 21.206940] raw: 1ffff00000010200 dead000000000100 dead000000000122 ffff002370c0fa00
[ 21.214671] raw: 0000000000000000 00000000802a002a 00000001ffffffff 0000000000000000
[ 21.222400] page dumped because: kasan: bad access detected
[ 21.227959]
[ 21.229438] Memory state around the buggy address:
[ 21.234218] ffff00236cdeb580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 21.241427] ffff00236cdeb600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 21.248637] >ffff00236cdeb680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 21.255845] ^
[ 21.259062] ffff00236cdeb700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 21.266272] ffff00236cdeb780: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 21.273480] ==================================================================
It seems that global pcc_data[pcc_ss_id] can be freed in
acpi_cppc_processor_exit(), but we may later reference this value, so
NULLify it when freed.
Also remove the useless setting of data "pcc_channel_acquired", which
we're about to free.
Fixes: 85b1407bf6d2 ("ACPI / CPPC: Make CPPC ACPI driver aware of PCC subspace IDs")
Signed-off-by: John Garry <john.garry@huawei.com>
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Update maintainers for MediaTek ethernet driver with Mark Lee.
He is familiar with MediaTek mt762x series ethernet devices and
will keep following maintenance from the vendor side.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Lee <Mark-MC.Lee@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jesse and Ido reported the following race condition:
<CPU A, t0> - Received packet A is forwarded and cached dst entry is
taken from the nexthop ('nhc->nhc_rth_input'). Calls skb_dst_set()
<t1> - Given Jesse has busy routers ("ingesting full BGP routing tables
from multiple ISPs"), route is added / deleted and rt_cache_flush() is
called
<CPU B, t2> - Received packet B tries to use the same cached dst entry
from t0, but rt_cache_valid() is no longer true and it is replaced in
rt_cache_route() by the newer one. This calls dst_dev_put() on the
original dst entry which assigns the blackhole netdev to 'dst->dev'
<CPU A, t3> - dst_input(skb) is called on packet A and it is dropped due
to 'dst->dev' being the blackhole netdev
There are 2 issues in the v4 routing code:
1. A per-netns counter is used to do the validation of the route. That
means whenever a route is changed in the netns, users of all routes in
the netns needs to redo lookup. v6 has an implementation of only
updating fn_sernum for routes that are affected.
2. When rt_cache_valid() returns false, rt_cache_route() is called to
throw away the current cache, and create a new one. This seems
unnecessary because as long as this route does not change, the route
cache does not need to be recreated.
To fully solve the above 2 issues, it probably needs quite some code
changes and requires careful testing, and does not suite for net branch.
So this patch only tries to add the deleted cached rt into the uncached
list, so user could still be able to use it to receive packets until
it's done.
Fixes: 95c47f9cf5e0 ("ipv4: call dst_dev_put() properly")
Signed-off-by: Wei Wang <weiwan@google.com>
Reported-by: Ido Schimmel <idosch@idosch.org>
Reported-by: Jesse Hathaway <jesse@mbuki-mvuki.org>
Tested-by: Jesse Hathaway <jesse@mbuki-mvuki.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Cc: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
...instead of -EINVAL. An issue was found with older kernel versions
while unplugging a NFS client with pending RPCs, and the wrong error
code here prevented it from recovering once link is back up with a
configured address.
Incidentally, this is not an issue anymore since commit 4f8943f80883
("SUNRPC: Replace direct task wakeups from softirq context"), included
in 5.2-rc7, had the effect of decoupling the forwarding of this error
by using SO_ERROR in xs_wake_error(), as pointed out by Benjamin
Coddington.
To the best of my knowledge, this isn't currently causing any further
issue, but the error code doesn't look appropriate anyway, and we
might hit this in other paths as well.
In detail, as analysed by Gonzalo Siero, once the route is deleted
because the interface is down, and can't be resolved and we return
-EINVAL here, this ends up, courtesy of inet_sk_rebuild_header(),
as the socket error seen by tcp_write_err(), called by
tcp_retransmit_timer().
In turn, tcp_write_err() indirectly calls xs_error_report(), which
wakes up the RPC pending tasks with a status of -EINVAL. This is then
seen by call_status() in the SUN RPC implementation, which aborts the
RPC call calling rpc_exit(), instead of handling this as a
potentially temporary condition, i.e. as a timeout.
Return -EINVAL only if the input parameters passed to
ip_route_output_key_hash_rcu() are actually invalid (this is the case
if the specified source address is multicast, limited broadcast or
all zeroes), but return -ENETUNREACH in all cases where, at the given
moment, the given source address doesn't allow resolving the route.
While at it, drop the initialisation of err to -ENETUNREACH, which
was added to __ip_route_output_key() back then by commit
0315e3827048 ("net: Fix behaviour of unreachable, blackhole and
prohibit routes"), but actually had no effect, as it was, and is,
overwritten by the fib_lookup() return code assignment, and anyway
ignored in all other branches, including the if (fl4->saddr) one:
I find this rather confusing, as it would look like -ENETUNREACH is
the "default" error, while that statement has no effect.
Also note that after commit fc75fc8339e7 ("ipv4: dont create routes
on down devices"), we would get -ENETUNREACH if the device is down,
but -EINVAL if the source address is specified and we can't resolve
the route, and this appears to be rather inconsistent.
Reported-by: Stefan Walter <walteste@inf.ethz.ch>
Analysed-by: Benjamin Coddington <bcodding@redhat.com>
Analysed-by: Gonzalo Siero <gsierohu@redhat.com>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The KSZ8795 PHY ID is in fact used by KSZ8794/KSZ8795/KSZ8765 switches.
Update the PHY ID and name to reflect that, as this family of switches
is commonly refered to as KSZ87xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The KSZ8051 PHY and the KSZ8794/KSZ8795/KSZ8765 switch share exactly the
same PHY ID. Since KSZ8051 is higher in the ksphy_driver[] list of PHYs
in the micrel PHY driver, it is used even with the KSZ87xx switch. This
is wrong, since the KSZ8051 configures registers of the PHY which are
not present on the simplified KSZ87xx switch PHYs and misconfigures
other registers of the KSZ87xx switch PHYs.
Fortunatelly, it is possible to tell apart the KSZ8051 PHY from the
KSZ87xx switch by checking the Basic Status register Bit 0, which is
read-only and indicates presence of the Extended Capability Registers.
The KSZ8051 PHY has those registers while the KSZ87xx switch does not.
This patch implements simple check for the presence of this bit for
both the KSZ8051 PHY and KSZ87xx switch, to let both use the correct
PHY driver instance.
Fixes: 9d162ed69f51 ("net: phy: micrel: add support for KSZ8795")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If ctx->cached_sq_head < nxt_sq_head, we should add UINT_MAX to tmp, not
tmp_nxt.
Fixes: 5da0fb1ab34c ("io_uring: consider the overflow of sequence for timeout req")
Signed-off-by: yangerkun <yangerkun@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We've got two issues with the non-regular file handling for non-blocking
IO:
1) We don't want to re-do a short read in full for a non-regular file,
as we can't just read the data again.
2) For non-regular files that don't support non-blocking IO attempts,
we need to punt to async context even if the file is opened as
non-blocking. Otherwise the caller always gets -EAGAIN.
Add two new request flags to handle these cases. One is just a cache
of the inode S_ISREG() status, the other tells io_uring that we always
need to punt this request to async context, even if REQ_F_NOWAIT is set.
Cc: stable@vger.kernel.org
Reported-by: Hrvoje Zeba <zeba.hrvoje@gmail.com>
Tested-by: Hrvoje Zeba <zeba.hrvoje@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The KSZ driver uses one regmap per register width (8/16/32), each with
it's own lock, but accessing the same set of registers. In theory, it
is possible to create a race condition between these regmaps, although
the underlying bus (SPI or I2C) locking should assure nothing bad will
really happen and the accesses would be correct.
To make the driver do the right thing, add one single shared mutex for
all the regmaps used by the driver instead. This assures that even if
some future hardware is on a bus which does not serialize the accesses
the same way SPI or I2C does, nothing bad will happen.
Note that the status_mutex was unused and only initied, hence it was
renamed and repurposed as the regmap mutex.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The KSZ87xx driver calls mutex_init() on mutexes already inited in
ksz_common.c ksz_switch_register(). Do not do it twice, drop the
reinitialization.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The stmmac_pcs_ctrl_ane() expects a register address as
argument 1, but for some reason the mac_device_info is
being passed.
Fix the warning (and possible bug) from sparse:
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2613:17: warning: incorrect type in argument 1 (different address spaces)
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2613:17: expected void [noderef] <asn:2> *ioaddr
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2613:17: got struct mac_device_info *hw
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Depending on when MC connects the DPNI to a MAC, Tx FQIDs may
not be available during probe time.
Read the FQIDs each time the link goes up to avoid using invalid
values. In case an error occurs or an invalid value is retrieved,
fall back to QDID-based enqueueing.
Fixes: 1fa0f68c9255 ("dpaa2-eth: Use FQ-based DPIO enqueue API")
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IRQ for the DPNI endpoint change event, resolving the issue
when a dynamically created DPNI gets a randomly generated hw address
when the endpoint is a DPMAC object.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The serial state information must not be embedded into another
data structure, as this interferes with cache handling for DMA
on architectures without cache coherence..
That would result in data corruption on some architectures
Allocating it separately.
v2: fix syntax error
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While it is useful for new drivers to use devm_platform_ioremap_resource,
this script is currently used to spam maintainers, often updating very
old drivers. The net benefit is the removal of 2 lines of code in the
driver but the review load for the maintainers is huge. As of now, more
that 560 patches have been sent, some of them obviously broken, as in:
https://lore.kernel.org/lkml/9bbcce19c777583815c92ce3c2ff2586@www.loen.fr/
Remove the script to reduce the spam.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Przemysław Kopa reports that since commit b516ea586d71 ("PCI: Enable
NVIDIA HDA controllers"), the discrete GPU Nvidia GeForce GT 540M on his
2011 Samsung laptop refuses to runtime suspend, resulting in a power
regression and excessive heat.
Rivera Valdez witnesses the same issue with a GeForce GT 525M (GF108M)
of the same era, as does another Arch Linux user named "R0AR" with a
more recent GeForce GTX 1050 Ti (GP107M).
The commit exposes the discrete GPU's HDA controller and all four codecs
on the controller do not set the CLKSTOP and EPSS bits in the Supported
Power States Response. They also do not set the PS-ClkStopOk bit in the
Get Power State Response. hda_codec_runtime_suspend() therefore does
not call snd_hdac_codec_link_down(), which prevents each codec and the
PCI device from runtime suspending.
The same issue is present on some AMD discrete GPUs and we addressed it
by forcing runtime PM despite the bits not being set, see commit
57cb54e53bdd ("ALSA: hda - Force to link down at runtime suspend on
ATI/AMD HDMI").
Do the same for Nvidia HDMI codecs.
Fixes: b516ea586d71 ("PCI: Enable NVIDIA HDA controllers")
Link: https://bbs.archlinux.org/viewtopic.php?pid=1865512
Link: https://bugs.freedesktop.org/show_bug.cgi?id=75985#c81
Reported-by: Przemysław Kopa <prymoo@gmail.com>
Reported-by: Rivera Valdez <riveravaldez@ysinembargo.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Daniel Drake <dan@reactivated.net>
Cc: stable@vger.kernel.org # v5.3+
Link: https://lore.kernel.org/r/3086bc75135c1e3567c5bc4f3cc4ff5cbf7a56c2.1571324194.git.lukas@wunner.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
GFP_NOWAIT allocation can fail anytime - it doesn't wait for memory being
available and it fails if the mempool is exhausted and there is not enough
memory.
If we go down this path:
map_bio -> mg_start -> alloc_migration -> mempool_alloc(GFP_NOWAIT)
we can see that map_bio() doesn't check the return value of mg_start(),
and the bio is leaked.
If we go down this path:
map_bio -> mg_start -> mg_lock_writes -> alloc_prison_cell ->
dm_bio_prison_alloc_cell_v2 -> mempool_alloc(GFP_NOWAIT) ->
mg_lock_writes -> mg_complete
the bio is ended with an error - it is unacceptable because it could
cause filesystem corruption if the machine ran out of memory
temporarily.
Change GFP_NOWAIT to GFP_NOIO, so that the mempool code will properly
wait until memory becomes available. mempool_alloc with GFP_NOIO can't
fail, so remove the code paths that deal with allocation failure.
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Both multi_cpu_stop() and set_state() access multi_stop_data::state
racily using plain accesses. These are subject to compiler
transformations which could break the intended behaviour of the code,
and this situation is detected by KCSAN on both arm64 and x86 (splats
below).
Improve matters by using READ_ONCE() and WRITE_ONCE() to ensure that the
compiler cannot elide, replay, or tear loads and stores.
In multi_cpu_stop() the two loads of multi_stop_data::state are expected to
be a consistent value, so snapshot the value into a temporary variable to
ensure this.
The state transitions are serialized by atomic manipulation of
multi_stop_data::num_threads, and other fields in multi_stop_data are not
modified while subject to concurrent reads.
KCSAN splat on arm64:
| BUG: KCSAN: data-race in multi_cpu_stop+0xa8/0x198 and set_state+0x80/0xb0
|
| write to 0xffff00001003bd00 of 4 bytes by task 24 on cpu 3:
| set_state+0x80/0xb0
| multi_cpu_stop+0x16c/0x198
| cpu_stopper_thread+0x170/0x298
| smpboot_thread_fn+0x40c/0x560
| kthread+0x1a8/0x1b0
| ret_from_fork+0x10/0x18
|
| read to 0xffff00001003bd00 of 4 bytes by task 14 on cpu 1:
| multi_cpu_stop+0xa8/0x198
| cpu_stopper_thread+0x170/0x298
| smpboot_thread_fn+0x40c/0x560
| kthread+0x1a8/0x1b0
| ret_from_fork+0x10/0x18
|
| Reported by Kernel Concurrency Sanitizer on:
| CPU: 1 PID: 14 Comm: migration/1 Not tainted 5.3.0-00007-g67ab35a199f4-dirty #3
| Hardware name: linux,dummy-virt (DT)
KCSAN splat on x86:
| write to 0xffffb0bac0013e18 of 4 bytes by task 19 on cpu 2:
| set_state kernel/stop_machine.c:170 [inline]
| ack_state kernel/stop_machine.c:177 [inline]
| multi_cpu_stop+0x1a4/0x220 kernel/stop_machine.c:227
| cpu_stopper_thread+0x19e/0x280 kernel/stop_machine.c:516
| smpboot_thread_fn+0x1a8/0x300 kernel/smpboot.c:165
| kthread+0x1b5/0x200 kernel/kthread.c:255
| ret_from_fork+0x35/0x40 arch/x86/entry/entry_64.S:352
|
| read to 0xffffb0bac0013e18 of 4 bytes by task 44 on cpu 7:
| multi_cpu_stop+0xb4/0x220 kernel/stop_machine.c:213
| cpu_stopper_thread+0x19e/0x280 kernel/stop_machine.c:516
| smpboot_thread_fn+0x1a8/0x300 kernel/smpboot.c:165
| kthread+0x1b5/0x200 kernel/kthread.c:255
| ret_from_fork+0x35/0x40 arch/x86/entry/entry_64.S:352
|
| Reported by Kernel Concurrency Sanitizer on:
| CPU: 7 PID: 44 Comm: migration/7 Not tainted 5.3.0+ #1
| Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marco Elver <elver@google.com>
Link: https://lkml.kernel.org/r/20191007104536.27276-1-mark.rutland@arm.com
|
|
On Asus MJ401TA (with Realtek ALC256), the headset mic is connected to
pin 0x19, with default configuration value 0x411111f0 (indicating no
physical connection).
Enable this by quirking the pin. Mic jack detection was also tested and
found to be working.
This enables use of the headset mic on this product.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191017081501.17135-1-drake@endlessm.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
BOSS Katana amplifiers cannot be used for recording or playback if quirks
are applied
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=195223
Signed-off-by: Szabolcs Szőke <szszoke.code@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191011171937.8013-1-szszoke.code@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The option --sort=ORDER was only introduced in tar 1.28 (2014), which
is rather new and might not be available in some setups.
This patch tries to replicate the previous behaviour as closely as
possible to fix the kheaders build for older environments. It does
not produce identical archives compared to the previous version due
to minor sorting differences but produces reproducible results itself
in my tests.
Reported-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Dmitry Goldin <dgoldin+lkml@protonmail.ch>
Tested-by: Andreas Schwab <schwab@suse.de>
Tested-by: Quentin Perret <qperret@google.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
disable ptp_ref_clk in suspend flow, and enable it in resume flow.
Fixes: f573c0b9c4e0 ("stmmac: move stmmac_clk, pclk, clk_ptp_ref and stmmac_rst to platform structure")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some drivers just call phy_ethtool_ksettings_set() to set the
links, for those phy drivers that use genphy_read_status(), if
autoneg is on, and the link is up, than execute "ethtool -s
ethx autoneg on" will cause "link partner" information disappear.
The call trace is phy_ethtool_ksettings_set()->phy_start_aneg()
->linkmode_zero(phydev->lp_advertising)->genphy_read_status(),
the link didn't change, so genphy_read_status() just return, and
phydev->lp_advertising is zero now.
This patch moves the clear operation of lp_advertising from
phy_start_aneg() to genphy_read_lpa()/genphy_c45_read_lpa(), and
if autoneg on and autoneg not complete, just clear what the
generic functions care about.
Fixes: 88d6272acaaa ("net: phy: avoid unneeded MDIO reads in genphy_read_status")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to extend the rcu_read_lock() section in rxrpc_error_report()
and use rcu_dereference_sk_user_data() instead of plain access
to sk->sk_user_data to make sure all rules are respected.
The compiler wont reload sk->sk_user_data at will, and RCU rules
prevent memory beeing freed too soon.
Fixes: f0308fb07080 ("rxrpc: Fix possible NULL pointer access in ICMP handling")
Fixes: 17926a79320a ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As preempt-to-busy leaves the request on the HW as the resubmission is
processed, that request may complete in the background and even cause a
second virtual request to enter queue. This second virtual request
breaks our "single request in the virtual pipeline" assumptions.
Furthermore, as the virtual request may be completed and retired, we
lose the reference the virtual engine assumes is held. Normally, just
removing the request from the scheduler queue removes it from the
engine, but the virtual engine keeps track of its singleton request via
its ve->request. This pointer needs protecting with a reference.
v2: Drop unnecessary motion of rq->engine = owner
Fixes: 22b7a426bbe1 ("drm/i915/execlists: Preempt-to-busy")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190923152844.8914-1-chris@chris-wilson.co.uk
(cherry picked from commit b647c7df01b75761b4c0b1cb6f4841088c0b1121)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Daniel Vetter uncovered a nasty cycle in using the mmu-notifiers to
invalidate userptr objects which also happen to be pulled into GGTT
mmaps. That is when we unbind the userptr object (on mmu invalidation),
we revoke all CPU mmaps, which may then recurse into mmu invalidation.
We looked for ways of breaking the cycle, but the revocation on
invalidation is required and cannot be avoided. The only solution we
could see was to not allow such GGTT bindings of userptr objects in the
first place. In practice, no one really wants to use a GGTT mmapping of
a CPU pointer...
Just before Daniel's explosive lockdep patches land in v5.4-rc1, we got
a genuine blip from CI:
<4>[ 246.793958] ======================================================
<4>[ 246.793972] WARNING: possible circular locking dependency detected
<4>[ 246.793989] 5.3.0-gbd6c56f50d15-drmtip_372+ #1 Tainted: G U
<4>[ 246.794003] ------------------------------------------------------
<4>[ 246.794017] kswapd0/145 is trying to acquire lock:
<4>[ 246.794030] 000000003f565be6 (&dev->struct_mutex/1){+.+.}, at: userptr_mn_invalidate_range_start+0x18f/0x220 [i915]
<4>[ 246.794250]
but task is already holding lock:
<4>[ 246.794263] 000000001799cef9 (&anon_vma->rwsem){++++}, at: page_lock_anon_vma_read+0xe6/0x2a0
<4>[ 246.794291]
which lock already depends on the new lock.
<4>[ 246.794307]
the existing dependency chain (in reverse order) is:
<4>[ 246.794322]
-> #3 (&anon_vma->rwsem){++++}:
<4>[ 246.794344] down_write+0x33/0x70
<4>[ 246.794357] __vma_adjust+0x3d9/0x7b0
<4>[ 246.794370] __split_vma+0x16a/0x180
<4>[ 246.794385] mprotect_fixup+0x2a5/0x320
<4>[ 246.794399] do_mprotect_pkey+0x208/0x2e0
<4>[ 246.794413] __x64_sys_mprotect+0x16/0x20
<4>[ 246.794429] do_syscall_64+0x55/0x1c0
<4>[ 246.794443] entry_SYSCALL_64_after_hwframe+0x49/0xbe
<4>[ 246.794456]
-> #2 (&mapping->i_mmap_rwsem){++++}:
<4>[ 246.794478] down_write+0x33/0x70
<4>[ 246.794493] unmap_mapping_pages+0x48/0x130
<4>[ 246.794519] i915_vma_revoke_mmap+0x81/0x1b0 [i915]
<4>[ 246.794519] i915_vma_unbind+0x11d/0x4a0 [i915]
<4>[ 246.794519] i915_vma_destroy+0x31/0x300 [i915]
<4>[ 246.794519] __i915_gem_free_objects+0xb8/0x4b0 [i915]
<4>[ 246.794519] drm_file_free.part.0+0x1e6/0x290
<4>[ 246.794519] drm_release+0xa6/0xe0
<4>[ 246.794519] __fput+0xc2/0x250
<4>[ 246.794519] task_work_run+0x82/0xb0
<4>[ 246.794519] do_exit+0x35b/0xdb0
<4>[ 246.794519] do_group_exit+0x34/0xb0
<4>[ 246.794519] __x64_sys_exit_group+0xf/0x10
<4>[ 246.794519] do_syscall_64+0x55/0x1c0
<4>[ 246.794519] entry_SYSCALL_64_after_hwframe+0x49/0xbe
<4>[ 246.794519]
-> #1 (&vm->mutex){+.+.}:
<4>[ 246.794519] i915_gem_shrinker_taints_mutex+0x6d/0xe0 [i915]
<4>[ 246.794519] i915_address_space_init+0x9f/0x160 [i915]
<4>[ 246.794519] i915_ggtt_init_hw+0x55/0x170 [i915]
<4>[ 246.794519] i915_driver_probe+0xc9f/0x1620 [i915]
<4>[ 246.794519] i915_pci_probe+0x43/0x1b0 [i915]
<4>[ 246.794519] pci_device_probe+0x9e/0x120
<4>[ 246.794519] really_probe+0xea/0x3d0
<4>[ 246.794519] driver_probe_device+0x10b/0x120
<4>[ 246.794519] device_driver_attach+0x4a/0x50
<4>[ 246.794519] __driver_attach+0x97/0x130
<4>[ 246.794519] bus_for_each_dev+0x74/0xc0
<4>[ 246.794519] bus_add_driver+0x13f/0x210
<4>[ 246.794519] driver_register+0x56/0xe0
<4>[ 246.794519] do_one_initcall+0x58/0x300
<4>[ 246.794519] do_init_module+0x56/0x1f6
<4>[ 246.794519] load_module+0x25bd/0x2a40
<4>[ 246.794519] __se_sys_finit_module+0xd3/0xf0
<4>[ 246.794519] do_syscall_64+0x55/0x1c0
<4>[ 246.794519] entry_SYSCALL_64_after_hwframe+0x49/0xbe
<4>[ 246.794519]
-> #0 (&dev->struct_mutex/1){+.+.}:
<4>[ 246.794519] __lock_acquire+0x15d8/0x1e90
<4>[ 246.794519] lock_acquire+0xa6/0x1c0
<4>[ 246.794519] __mutex_lock+0x9d/0x9b0
<4>[ 246.794519] userptr_mn_invalidate_range_start+0x18f/0x220 [i915]
<4>[ 246.794519] __mmu_notifier_invalidate_range_start+0x85/0x110
<4>[ 246.794519] try_to_unmap_one+0x76b/0x860
<4>[ 246.794519] rmap_walk_anon+0x104/0x280
<4>[ 246.794519] try_to_unmap+0xc0/0xf0
<4>[ 246.794519] shrink_page_list+0x561/0xc10
<4>[ 246.794519] shrink_inactive_list+0x220/0x440
<4>[ 246.794519] shrink_node_memcg+0x36e/0x740
<4>[ 246.794519] shrink_node+0xcb/0x490
<4>[ 246.794519] balance_pgdat+0x241/0x580
<4>[ 246.794519] kswapd+0x16c/0x530
<4>[ 246.794519] kthread+0x119/0x130
<4>[ 246.794519] ret_from_fork+0x24/0x50
<4>[ 246.794519]
other info that might help us debug this:
<4>[ 246.794519] Chain exists of:
&dev->struct_mutex/1 --> &mapping->i_mmap_rwsem --> &anon_vma->rwsem
<4>[ 246.794519] Possible unsafe locking scenario:
<4>[ 246.794519] CPU0 CPU1
<4>[ 246.794519] ---- ----
<4>[ 246.794519] lock(&anon_vma->rwsem);
<4>[ 246.794519] lock(&mapping->i_mmap_rwsem);
<4>[ 246.794519] lock(&anon_vma->rwsem);
<4>[ 246.794519] lock(&dev->struct_mutex/1);
<4>[ 246.794519]
*** DEADLOCK ***
v2: Say no to mmap_ioctl
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111744
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111870
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190928082546.3473-1-chris@chris-wilson.co.uk
(cherry picked from commit a4311745bba9763e3c965643d4531bd5765b0513)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
The first come first served apporoach to handling the VBT
child device AUX ch conflicts has backfired. We have machines
in the wild where the VBT specifies both port A eDP and
port E DP (in that order) with port E being the real one.
So let's try to flip the preference around and let the last
child device win once again.
Cc: stable@vger.kernel.org
Cc: Jani Nikula <jani.nikula@intel.com>
Tested-by: Masami Ichikawa <masami256@gmail.com>
Tested-by: Torsten <freedesktop201910@liggy.de>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111966
Fixes: 36a0f92020dc ("drm/i915/bios: make child device order the priority order")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191011202030.8829-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 41e35ffb380bde1379e4030bb5b2ac824d5139cf)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Pull setting -EIO on the hung requests into its own utility function.
Having allowed ourselves to short-circuit submission of completed
requests, we can now do the mark_eio() prior to submission and avoid
some redundant operations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190923110056.15176-4-chris@chris-wilson.co.uk
(cherry picked from commit 0d7cf7bc15e75bf79f2f65d61d19f896609f816a)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
This reverts commit b0818f80c8c1bc215bba276bd61c216014fab23b.
Started seeing weird behavior after this patch especially in
the IPv6 code path. Haven't root caused it, but since this was
applied to net branch, taking a precautionary measure to revert
it and look / analyze those failures
Revert this now and I'll send a better fix after analysing / fixing
the weirdness observed.
CC: Eric Dumazet <edumazet@google.com>
CC: Wei Wang <weiwan@google.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sign-extending TTBR1 addresses when converting to an untagged address
breaks the documented POSIX semantics for mlock() in some obscure error
cases where we end up returning -EINVAL instead of -ENOMEM as a direct
result of rewriting the upper address bits.
Rework the untagged_addr() macro to preserve the upper address bits for
TTBR1 addresses and only clear the tag bits for user addresses. This
matches the behaviour of the 'clear_address_tag' assembly macro, so
rename that and align the implementations at the same time so that they
use the same instruction sequences for the tag manipulation.
Link: https://lore.kernel.org/stable/20191014162651.GF19200@arrakis.emea.arm.com/
Reported-by: Jan Stancek <jstancek@redhat.com>
Tested-by: Jan Stancek <jstancek@redhat.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
When detecting a spurious EL1 translation fault, we have the CPU retry
the translation using an AT S1E1R instruction, and inspect PAR_EL1 to
determine if the fault was spurious.
When PAR_EL1.F == 0, the AT instruction successfully translated the
address without a fault, which implies the original fault was spurious.
However, in this case we return false and treat the original fault as if
it was not spurious.
Invert the return value so that we treat such a case as spurious.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Fixes: 42f91093b043 ("arm64: mm: Ignore spurious translation faults taken from the kernel")
Tested-by: James Morse <james.morse@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The 'F' field of the PAR_EL1 register lives in bit 0, not bit 1.
Fix the broken definition in 'sysreg.h'.
Fixes: e8620cff9994 ("arm64: sysreg: Add some field definitions for PAR_EL1")
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Preempting from IRQ-return means that the task has its PSTATE saved
on the stack, which will get restored when the task is resumed and does
the actual IRQ return.
However, enabling some CPU features requires modifying the PSTATE. This
means that, if a task was scheduled out during an IRQ-return before all
CPU features are enabled, the task might restore a PSTATE that does not
include the feature enablement changes once scheduled back in.
* Task 1:
PAN == 0 ---| |---------------
| |<- return from IRQ, PSTATE.PAN = 0
| <- IRQ |
+--------+ <- preempt() +--
^
|
reschedule Task 1, PSTATE.PAN == 1
* Init:
--------------------+------------------------
^
|
enable_cpu_features
set PSTATE.PAN on all CPUs
Worse than this, since PSTATE is untouched when task switching is done,
a task missing the new bits in PSTATE might affect another task, if both
do direct calls to schedule() (outside of IRQ/exception contexts).
Fix this by preventing preemption on IRQ-return until features are
enabled on all CPUs.
This way the only PSTATE values that are saved on the stack are from
synchronous exceptions. These are expected to be fatal this early, the
exception is BRK for WARN_ON(), but as this uses do_debug_exception()
which keeps IRQs masked, it shouldn't call schedule().
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
[james: Replaced a really cool hack, with an even simpler static key in C.
expanded commit message with Julien's cover-letter ascii art]
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The message should match the parameter, i.e. raid0.default_layout.
Fixes: c84a1372df92 ("md/raid0: avoid RAID0 data corruption due to layout confusion.")
Cc: NeilBrown <neilb@suse.de>
Reported-by: Ivan Topolsky <doktor.yak@gmail.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
|
|
The __kthread_queue_delayed_work is not exported so
make it static, to avoid the following sparse warning:
kernel/kthread.c:869:6: warning: symbol '__kthread_queue_delayed_work' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
For the new Spreadtrum pin controller, it expands 6bits to describe the
pin sleep mode with adding one CM4_SLEEP mode, which means the pin sleep
related configuration will be loaded automatically by hardware when the
CM4 system goes into deep sleep mode.
Signed-off-by: Bruce Chen <bruce.chen@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/8ae52263b0625c416461821c457e6789b67170b6.1571228451.git.baolin.wang@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|