Age | Commit message (Collapse) | Author | Files | Lines |
|
Since commit b45f64d16d45 ("mlxsw: spectrum_router: Use FIB notifications
instead of switchdev calls") we reflect to the device the entire FIB
table and not only FIBs that point to netdevs created by the driver.
During module removal, FIBs of the second type are removed following
NETDEV_UNREGISTER events sent. The other FIBs are still present in both
the driver's cache and the device's table.
Fix this by iterating over all the FIB tables in the device and flush
them. There's no need to take locks, as we're the only writer.
Fixes: b45f64d16d45 ("mlxsw: spectrum_router: Use FIB notifications instead of switchdev calls")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device's neighbour table is periodically dumped in order to update
the kernel about active neighbours. A single dump session may span
multiple queries, until the response carries less records than requested
or when a record (can contain up to four neighbour entries) is not full.
Current code stops the session when the number of returned records is
zero, which can result in infinite loop in case of high packet rate.
Fix this by stopping the session according to the above logic.
Fixes: c723c735fa6b ("mlxsw: spectrum_router: Periodically update the kernel's neigh table")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When binding port to a newly created span entry, its refcount is
initialized to zero even though it has a bound port. That leads
to unexpected behaviour when the user tries to delete that port
from the span entry.
Fix this by initializing the reference count to 1.
Also add a warning to put function.
Fixes: 763b4b70afcd ("mlxsw: spectrum: Add support in matchall mirror TC offloading")
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since now, the table with same id in multiple netnamespaces were squashed
to a single virtual router. That is not only incorrect, it also causes
error messages when trying to use RALUE register to do double remove
of FIB entries, like this one:
mlxsw_spectrum 0000:03:00.0: EMAD reg access failed (tid=facb831c00007b20,reg_id=8013(ralue),type=write,status=7(bad parameter))
Since we don't allow ports to change namespaces (NETIF_F_NETNS_LOCAL),
and the infrastructure is not yet prepared to handle netnamespaces, just
ignore FIB notification events for non-init namespaces. That is clear to
do since we don't need to offload them.
Fixes: b45f64d16d45 ("mlxsw: spectrum_router: Use FIB notifications instead of switchdev calls")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__neigh_create function works in a different way than assumed.
It passes "n" as a parameter to ndo_neigh_construct. But this "n" might
be destroyed right away before __neigh_create() returns in case there is
already another neighbour struct in the hashtable with the same dev and
primary key. That is not expected by mlxsw_sp_router_neigh_construct()
and the stored "n" points to freed memory, eventually leading to crash.
Fix this by doing tight 1:1 coupling between neighbour struct and
internal driver neigh_entry. That allows to narrow down the key in
internal driver hashtable to do lookups by "n" only.
Fixes: 6cf3c971dc84 ("mlxsw: spectrum_router: Add private neigh table")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 9d2afba058722d40cc02f430229c91611c0e8d16.
The original issue would possibly exist if an external module
tried calling our "ethtool_ops" without checking if it still
exists.
The right way of solving it is by simply doing the check in
the caller side.
Currently, no action is required as there's no such use case.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When prof_sel is invalid, mlx5_core_warn is called but the
mlx5_core_dev is not initialized yet. Solution is moving the prof_sel code
after dev->pdev assignment
Fixes: 2974ab6e8bd8 ('net/mlx5: Improve driver log messages')
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As for the current generation of the mlx5 HW (CX4/CX4-Lx) per flow vlan
push/pop actions are emulated, we must not program them to the firmware.
Fixes: f5f82476090f ('net/mlx5: E-Switch, Support VLAN actions in the offloads mode')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We ignored the vlan priority in offloaded TC rules matching part,
fix that.
Fixes: 095b6cfd69ce ('net/mlx5e: Add TC vlan match parsing')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VF reps should be altogether on the same NS as they were created.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In mlx5e_open_channel CQs must be created before napi is enabled.
Here we move the XDP CQ creation to satisfy that fact.
mlx5e_close_channel is already working according to the right order.
Fixes: b5503b994ed5 ("net/mlx5e: XDP TX forwarding support")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of mlx5e_open_rq fails the error handling will jump to
label err_close_xdp_sq and will try to close the xdp_sq unconditionally.
xdp_sq is valid only in case of XDP use cases, i.e priv->xdp_prog is
not null.
To fix this in this patch we test xdp_sq validity prior to closing it.
In addition we now close the xdp_sq.cq as well.
Fixes: b5503b994ed5 ("net/mlx5e: XDP TX forwarding support")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'create_root_ns()' does not return an error pointer, so the test can be
simplified to be more consistent.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the device, a MID entry represents a group of local ports, which can
later be bound to a MDB entry.
The lookup of an existing MID entry is currently done using the provided
MC MAC address and VID, from the Linux bridge. However, this can result
in an incorrect reuse of the same MID index in different VLAN-unaware
bridges (same IP MC group and VID 0).
Fix this by performing the lookup based on FID instead of VID, which is
unique across different bridges.
Fixes: 3a49b4fde2a1 ("mlxsw: Adding layer 2 multicast support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Following the previous patch, as an optimization, the slave will
not even bother sending the DUMP_ETH_STATS command over the
comm channel.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mlx4_en_DUMP_ETH_STATS took the *counter mutex* and then
called the FW command, with WRAPPED attribute. As a result, the fw command
is wrapped on the Hypervisor when it calls mlx4_en_DUMP_ETH_STATS.
The FW command wrapper flow on the hypervisor takes the *slave_cmd_mutex*
during processing.
At the same time, a VF could be in the process of coming up, and could
call mlx4_QUERY_FUNC_CAP. On the hypervisor, the command flow takes the
*slave_cmd_mutex*, then executes mlx4_QUERY_FUNC_CAP_wrapper.
mlx4_QUERY_FUNC_CAP wrapper calls mlx4_get_default_counter_index(),
which takes the *counter mutex*. DEADLOCK.
The fix is that the DUMP_ETH_STATS fw command should be called with
the NATIVE attribute, so that on the hypervisor, this command does not
enter the wrapper flow.
Since the Hypervisor no longer goes through the wrapper code, we also
simply return 0 in mlx4_DUMP_ETH_STATS_wrapper (i.e.the function succeeds,
but the returned data will be all zeroes).
No need to test if it is the Hypervisor going through the wrapper.
Fixes: f9baff509f8a ("mlx4_core: Add "native" argument to mlx4_cmd ...")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently interrupt test that is part of ethtool selftest runs the
check over all interrupt vectors of the device.
In mlx4_en package part of interrupt vectors are uninitialized since
mlx4_ib doesn't exist. This causes NOP FW command to time out.
Change logic to test current port interrupt vectors only.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the Hypervisor, there are several FW commands which are invoked
before the comm channel is initialized (in mlx4_multi_func_init).
These include MOD_STAT_CONFIG, QUERY_DEV_CAP, INIT_HCA, and others.
If any of these commands fails, say with a timeout, the Hypervisor
driver enters the internal error reset flow. In this flow, the driver
attempts to notify all slaves via the comm channel that an internal error
has occurred.
Since the comm channel has not yet been initialized (i.e., mapped via
ioremap), this will cause dereferencing a NULL pointer.
To fix this, do not access the comm channel in the internal error flow
if it has not yet been initialized.
Fixes: 55ad359225b2 ("net/mlx4_core: Enable device recovery flow with SRIOV")
Fixes: ab9c17a009ee ("mlx4_core: Modify driver initialization flow to accommodate SRIOV for Ethernet")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a kernel panic that occurs as a result of an asynchronous event
handled in roce_gid_mgmt:
mlx4_en_get_drvinfo is called and accesses freed resources.
This happens in a shutdown flow only, since pci device is destroyed
while netdevice is still alive.
Fixes: c27a02cd94d6 ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC")
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently there is a race between incoming traffic and
initialization flow. HW is able to receive the packets
after INIT_PORT is done and unicast steering is configured.
Before we set priv->port_up NAPI is not scheduled and
receive queues become full. Therefore we never get
new interrupts about the completions.
This issue could happen if running heavy traffic during
bringing port up.
The resolution is to schedule NAPI once port_up is set.
If receive queues were full this will process all cqes
and release them.
Fixes: c27a02cd94d6 ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When doing roundup_pow_of_two for large enough number with
bit 31, an overflow will occur and a value equal to 1 will
be returned. In this case 1 will be subtracted from the return
value and division by zero will be reached.
Fixes: 31c128b66e5b ("net/mlx4_en: Choose time-stamping shift value according to HW frequency")
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the default status of quality of service back to disabled,
as it hurts performance in some cases.
Fixes: 38438f7c7e8c ("net/mlx4: Set enhanced QoS support by default when ...")
Signed-off-by: Moshe Lazer <moshel@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When only one port type is supported, it should be read only.
We reject changing requests, even to the auto sense mode.
Fixes: 27bf91d6a0d5 ("mlx4_core: Add link type autosensing")
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The resource type enum in the resource tracker was incorrect.
RES_EQ was put in the position of RES_NPORT_ID (a FC resource).
Since the remaining resources maintain their current values,
and RES_EQ is not passed from slaves to the hypervisor in any
FW command, this change affects only the hypervisor.
Therefore, there is no backwards-compatibility issue.
Fixes: 623ed84b1f95 ("mlx4_core: initial header-file changes for SRIOV support")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is an old warning about mlx4_SW2HW_EQ_wrapper on x86:
ethernet/mellanox/mlx4/resource_tracker.c: In function ‘mlx4_SW2HW_EQ_wrapper’:
ethernet/mellanox/mlx4/resource_tracker.c:3071:10: error: ‘eq’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
The problem here is that gcc won't track the state of the variable
across a spin_unlock. Moving the assignment out of the lock is
safe here and avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the firmware can't work with a page with dma address 0.
Passing such an address to the firmware will cause the give_pages
command to fail.
To avoid this, in case we get a 0 dma address of a page from the
dma engine, we avoid passing it to FW by remapping to get an address
other than 0.
Fixes: bf0bf77f6519 ('mlx5: Support communicating arbitrary host...')
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case that the kernel PCI error handlers are not called, we will
trigger our own recovery flow.
The health work will give priority to the kernel pci error handlers to
recover the PCI by waiting for a small period, if the pci error handlers
are not triggered the manual recovery flow will be executed.
We don't save pci state in case of manual recovery because it will ruin the
pci configuration space and we will lose dma sync.
Fixes: 89d44f0a6c73 ('net/mlx5_core: Add pci error handlers to mlx5_core driver')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently there is a race between the health care work and the kernel
pci error handlers because both of them detect the error, the first one
to be called will do the error handling.
There is a chance that health care will disable the pci after resuming
pci slot.
Also create a separate WQ because now we will have two types of health
works, one for the error detection and one for the recovery.
Fixes: 89d44f0a6c73 ('net/mlx5_core: Add pci error handlers to mlx5_core driver')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The health sick status should be cleared when we start the health poll.
This is crucial for driver reload (unload + load) in order to behave
right in case of health issue.
Fixes: fd76ee4da55a ('net/mlx5_core: Fix internal error detection conditions')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Ingress/Egress ACL enable function may fail and it should return
status to its caller to avoid NULL pointer dereference.
Fixes: f942380c1239 ('net/mlx5: E-Switch, Vport ingress/egress ACLs rules for spoofchk')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Detaching the netdev before unregistering it cause some netdev cleanup
ndos to fail because they check presence of the netdev, so we need to
unregister the netdev first.
Fixes: 26e59d8077a3 ('net/mlx5e: Implement mlx5e interface attach/detach callbacks')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of predicting the index of the wanted LRO timeout value from
hardware capabilities, look for the nearest LRO timeout value.
Fixes: 5c50368f3831 ('net/mlx5e: Light-weight netdev open/stop')
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, last use timestamp is initialized to zero.
This is not the expected value by higher layers such as
when we do TC action offloading. To fix that, set it to
the current time, e.g when the counter/rule is offloaded.
This is the same behaviour of non-offloaded TC actions.
Fixes: 43a335e055bb ('mlx5_core: Flow counters infrastructure')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Autogroups groups num is increased when creating a new flow group,
but is never decreased.
Now decreasing it when deleting a flow group.
Fixes: f0d22d187473 ('net/mlx5_core: Introduce flow steering autogrouped flow table')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Finding a new autogroup range is done by going over a group list
sorted by each group start index. The search is stopped after finding
the first free range. Adding the newly created group to the list is
wrongly added to the end of the list regardless of its start index as
the parameter of where to insert it is ignored.
This commit makes sure to use that unused parameter to insert
it where requested.
Fixes: f0d22d187473 ('net/mlx5_core: Introduce flow steering autogrouped flow table')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Always query the HCA caps after setting them to update the capablities
data structures. Not doing so results in incorrect capabilities being
reported including max_dc, max_qp and several others.
Fixes: 59211bd3b632 ("net/mlx5: Split the load/unload flow into hardware
and software flows")
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ARM 64B cache line systems have L1_CACHE_BYTES set to 128.
cache_line_size() will return the correct size.
Fixes: cf50b5efa2fe('net/mlx5_core/ib: New device capabilities
handling.')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only trees which are in use should be compared to requested prefix usage.
Fixes: 53342023eed9 ("mlxsw: spectrum_router: Implement LPM trees management")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the prefix bitlist is not saved for LPM trees, causing the
compare to always fail which causes the tree to be destroyed and created
for every inserted and removed FIB entry. So fix this by saving
the bitlist as it should have been done from the very beginning.
Fixes: 53342023eed9 ("mlxsw: spectrum_router: Implement LPM trees management")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SwitchX2 firmware does not implement reset done yet. Moreover, when
busy-polled for ready magic, that slows down firmware and reset takes
longer than the defined timeout, causing initialization to fail.
So restore the previous behaviour and just sleep in this case.
Fixes: 233fa44bd67a ("mlxsw: pci: Implement reset done check")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When creating an ethernet port fails, we must move the port to disable,
otherwise putting the port in switch partition 0 (ETH) or 1 (IB) will
always fails.
Fixes: 31557f0f9755 ("mlxsw: Introduce Mellanox SwitchX-2 ASIC support")
Signed-off-by: Elad Raz <eladr@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function return value is not checked anywhere. Also, the warning
causes huge slowdown when removing large number of FIB entries which
were not offloaded, because of ordering issue. Ido's preparing
a patchset to fix the ordering issue, but that is definitelly not
net tree material.
Fixes: b45f64d16d45 ("mlxsw: spectrum_router: Use FIB notifications instead of switchdev calls")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By a mistake, there is tree index 0 passed to RALTB. Should be
MLXSW_SP_LPM_TREE_MIN.
Fixes: b45f64d16d45 ("mlxsw: spectrum_router: Use FIB notifications instead of switchdev calls")
Reported-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In cases where the number of tx rings is not a multiple of the number of
rx rings, the tx completion event will be handled on a different core
from the transmit and population of the ring. Races on the ring will
lead to a double-free of the page, and possibly other corruption.
The rings are initialized by default with a valid multiple of rings,
based on the number of cpus, therefore an invalid configuration requires
ethtool to change the ring layout. For instance 'ethtool -L eth0 rx 9 tx
8' will cause packets received on rx0, and XDP_TX'd to tx48, to be
completed on cpu3 (48 % 9 == 3).
Resolve this discrepancy by shifting the irq for the xdp tx queues to
start again from 0, modulo rx_ring_num.
Fixes: 9ecc2d86171a ("net/mlx4_en: add xdp forwarding and data write support")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I am hitting this in mlx5:
drivers/net/ethernet/mellanox/mlx5/core/pagealloc.c: In function
reclaim_pages_cmd.clone.0:
drivers/net/ethernet/mellanox/mlx5/core/pagealloc.c:346: error: call
to __compiletime_assert_346 declared with attribute error:
BUILD_BUG_ON failed: __mlx5_bit_off(manage_pages_out, pas[i]) % 64
drivers/net/ethernet/mellanox/mlx5/core/pagealloc.c: In function give_pages:
drivers/net/ethernet/mellanox/mlx5/core/pagealloc.c:291: error: call
to __compiletime_assert_291 declared with attribute error:
BUILD_BUG_ON failed: __mlx5_bit_off(manage_pages_in, pas[i]) % 64
Problem is that this is doing a BUILD_BUG_ON on a non-constant
expression because of trying to take offset of pas[i] in the
structure.
Fix is to create MLX5_ARRAY_SET64 that takes an additional argument
that is the field index to separate between BUILD_BUG_ON on the array
constant field and the indexed field to assign the value to.
There are two callers of MLX5_SET64 that are trying to get a variable
offset, change those to call MLX5_ARRAY_SET64 passing 'pas' and 'i'
as the arguments to use in the offset check and the indexed value
assignment.
Fixes: a533ed5e179cd ("net/mlx5: Pages management commands via mlx5 ifc")
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull main rdma updates from Doug Ledford:
"This is the main pull request for the rdma stack this release. The
code has been through 0day and I had it tagged for linux-next testing
for a couple days.
Summary:
- updates to mlx5
- updates to mlx4 (two conflicts, both minor and easily resolved)
- updates to iw_cxgb4 (one conflict, not so obvious to resolve,
proper resolution is to keep the code in cxgb4_main.c as it is in
Linus' tree as attach_uld was refactored and moved into
cxgb4_uld.c)
- improvements to uAPI (moved vendor specific API elements to uAPI
area)
- add hns-roce driver and hns and hns-roce ACPI reset support
- conversion of all rdma code away from deprecated
create_singlethread_workqueue
- security improvement: remove unsafe ib_get_dma_mr (breaks lustre in
staging)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (75 commits)
staging/lustre: Disable InfiniBand support
iw_cxgb4: add fast-path for small REG_MR operations
cxgb4: advertise support for FR_NSMR_TPTE_WR
IB/core: correctly handle rdma_rw_init_mrs() failure
IB/srp: Fix infinite loop when FMR sg[0].offset != 0
IB/srp: Remove an unused argument
IB/core: Improve ib_map_mr_sg() documentation
IB/mlx4: Fix possible vl/sl field mismatch in LRH header in QP1 packets
IB/mthca: Move user vendor structures
IB/nes: Move user vendor structures
IB/ocrdma: Move user vendor structures
IB/mlx4: Move user vendor structures
IB/cxgb4: Move user vendor structures
IB/cxgb3: Move user vendor structures
IB/mlx5: Move and decouple user vendor structures
IB/{core,hw}: Add constant for node_desc
ipoib: Make ipoib_warn ratelimited
IB/mlx4/alias_GUID: Remove deprecated create_singlethread_workqueue
IB/ipoib_verbs: Remove deprecated create_singlethread_workqueue
IB/ipoib: Remove deprecated create_singlethread_workqueue
...
|
|
In MLX qp packets, the LRH (built by the driver) has both a VL field
and an SL field. When building a QP1 packet, the VL field should
reflect the SLtoVL mapping and not arbitrarily contain zero (as is
done now). This bug causes credit problems in IB switches at
high rates of QP1 packets.
The fix is to cache the SL to VL mapping in the driver, and look up
the VL mapped to the SL provided in the send request when sending
QP1 packets.
For FW versions which support generating a port_management_config_change
event with subtype sl-to-vl-table-change, the driver uses that event
to update its sl-to-vl mapping cache. Otherwise, the driver snoops
incoming SMP mads to update the cache.
There remains the case where the FW is running in secure-host mode
(so no QP0 packets are delivered to the driver), and the FW does not
generate the sl2vl mapping change event. To support this case, the
driver updates (via querying the FW) its sl2vl mapping cache when
running in secure-host mode when it receives either a Port Up event
or a client-reregister event (where the port is still up, but there
may have been an opensm failover).
OpenSM modifies the sl2vl mapping before Port Up and Client-reregister
events occur, so if there is a mapping change the driver's cache will
be properly updated.
Fixes: 225c7b1feef1 ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
In order to specify that the mlxsw switchx2 driver needs additional
headroom for packets, there have been use of the hard_header_len field of
the netdevice struct.
This commit changes that to use needed_headroom instead, as this is the
correct way to do that.
Fixes: 31557f0f9755 ("mlxsw: Introduce Mellanox SwitchX-2 ASIC support")
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to specify that the mlxsw spectrum driver needs additional
headroom for packets, there have been use of the hard_header_len field of
the netdevice struct.
This commit changes that to use needed_headroom instead, as this is the
correct way to do that.
Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If fi->fib_nhs is zero, the router interface pointer is uninitialized, as shown by
this warning:
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c: In function 'mlxsw_sp_router_fib_event':
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:1674:21: error: 'r' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:1643:23: note: 'r' was declared here
This changes the loop so we handle the case the same way as finding no router
interface pointer attached to one of the nexthops to ensure we always
trap here instead of using uninitialized data.
Fixes: b45f64d16d45 ("mlxsw: spectrum_router: Use FIB notifications instead of switchdev calls")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|