| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Saeed Mahameed says:
====================
mlx5-updates-2019-08-22
Misc updates for mlx5e net device driver
1) Maxim and Tariq add the support for LAG TX port affinity distribution
When VF LAG is enabled, VFs netdevs will round-robin the TX affinity
of their tx queues among the different LAG ports.
2) Aya adds the support for ip-in-ip RSS.
3) Marina adds the support for ip-in-ip TX TSO and checksum offloads.
4) Moshe adds a device internal drop counter to mlx5 ethtool stats.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On Spectrum-1, timestamped PTP packets and the corresponding timestamps need to
be kept in caches until both are available, at which point they are matched up
and packets forwarded as appropriate. However, not all packets will ever see
their timestamp, and not all timestamps will ever see their packet. It is
necessary to dispose of such abandoned entries, so a garbage collector was
introduced in commit 5d23e4159772 ("mlxsw: spectrum: PTP: Garbage-collect
unmatched entries").
If these GC events happen often, it is a sign of a problem. However because this
whole mechanism is taking place behind the scenes, there is no direct way to
determine whether garbage collection took place.
Therefore to fix this, on Spectrum-1 only, expose four artificial ethtool
counters for the GC events: GCd timestamps and packets, in TX and RX directions.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new version supports extended error reporting from firmware via a
new TLV in the EMAD packet. Similar to netlink extended ack.
It also fixes an issue in the PCI code that can result in false AER
errors under high Tx rate.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After 50G-1-lane and 100G-2-lanes link modes were introduced, the driver
is facing situations in which the hardware auto negotiates not only on
speed and type, but also on number of lanes.
Prevent auto negotiation on number of lanes by allowing only port speeds
that can be supported on a given port according to its width.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 275e928f1911 ("mlxsw: spectrum: Prevent force of 56G") prevented
the driver from setting a speed of 56G when auto-negotiation is off.
This is the only speed supported by mlxsw that cannot be set when
auto-negotiation is off, which makes it difficult to write generic
tests.
Further, the speed is not supported by newer ASICs such as Spectrum-2
and to the best of our knowledge it is not used by current users.
Therefore, remove 56G support from mlxsw.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tunnels
Add TX offloads support for IP-in-IP tunneled packets by reporting
the needed netdev features.
Signed-off-by: Marina Varshaver <marinav@mellanox.com>
Signed-off-by: Avihu Hagag <avihuh@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Use generic function for checking tunnel stateless offload capability
instead of separate macros.
Signed-off-by: Marina Varshaver <marinav@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add support for inner header RSS on IP-in-IP and IPv6 tunneled packets.
Add rules to the steering table regarding outer IP header, with
IPv4/6->IP-in-IP. Tunneled packets with protocol numbers: 0x4 (IP-in-IP)
and 0x29 (IPv6) are RSS-ed on the inner IP header.
Separate FW dependencies between flow table inner IP capabilities and
GRE offload support. Allowing this feature even if GRE offload is not
supported. Tested with multi stream TCP traffic tunneled with IPnIP.
Verified that:
Without this patch, only a single RX ring was processing the traffic.
With this patch, multiple RX rings were processing the traffic.
Verified with and without GRE offload support.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Move function which indicates whether tunnel inner flow table is
supported from en.h to en_fs.c. It fits better right after tunnel
protocol rules definitions.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Added the following packets drop counter:
Device out of buffer - counts packets which were dropped due to full
device internal receive queue.
This counter will be shown on ethtool as a new counter called
dev_out_of_buffer.
The counter is read from FW by command QUERY_VNIC_ENV.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When the VF LAG is in use, round-robin the TX affinity of channels among
the different ports, if supported by the firmware. Create a set of TISes
per port, while doing round-robin of the channels over the different
sets. Let all SQs of a channel share the same set of TISes.
If lag_tx_port_affinity HCA cap bit is supported, num_lag_ports > 1 and
we aren't the LACP owner (PF in the regular use), assign the affinities,
otherwise use tx_affinity == 0 in TIS context to let the FW assign the
affinities itself. The TISes of the LACP owner are mapped only to the
native physical port.
For VFs, the starting port for round-robin is determined by its vhca_id,
because a VF may have only one channel if attached to a single-core VM.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
For better modularity and code sharing.
Function internal change to be introduced in the next patches.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Fix a typo in 'mlx5e_refomrat_wol_mode_mlx5_to_linux' and
'mlx5e_refomrat_wol_mode_linux_to_mlx5' function names:
"refomrat" -> "reformat".
Fixes: 928cfe8745a6 ("net/mlx5e: Wake On LAN support")
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
mlx5 HW spec and bits updates:
1) Aya exposes IP-in-IP capability in mlx5_core.
2) Maxim exposes lag tx port affinity capabilities.
3) Moshe adds VNIC_ENV internal rq counter bits.
4) ODP capabilities for DC transport
Misc updates:
5) Saeed, two compiler warnings cleanups
6) Add XRQ legacy commands opcodes
7) Use refcount_t for refcount
8) fix a -Wstringop-truncation warning
|
|
In mlx5_core initialization, query max ODP capabilities for DC transport
from FW and set as current capabilities.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
|
|
In file included from ./arch/powerpc/include/asm/paca.h:15,
from ./arch/powerpc/include/asm/current.h:13,
from ./include/linux/thread_info.h:21,
from ./include/asm-generic/preempt.h:5,
from ./arch/powerpc/include/generated/asm/preempt.h:1,
from ./include/linux/preempt.h:78,
from ./include/linux/spinlock.h:51,
from ./include/linux/wait.h:9,
from ./include/linux/completion.h:12,
from ./include/linux/mlx5/driver.h:37,
from
drivers/net/ethernet/mellanox/mlx5/core/lib/eq.h:6,
from
drivers/net/ethernet/mellanox/mlx5/core/diag/fw_tracer.c:33:
In function 'strncpy',
inlined from 'mlx5_fw_tracer_save_trace' at
drivers/net/ethernet/mellanox/mlx5/core/diag/fw_tracer.c:549:2,
inlined from 'mlx5_tracer_print_trace' at
drivers/net/ethernet/mellanox/mlx5/core/diag/fw_tracer.c:574:2:
./include/linux/string.h:305:9: warning: '__builtin_strncpy' output may
be truncated copying 256 bytes from a string of length 511
[-Wstringop-truncation]
return __builtin_strncpy(p, q, size);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix it by using the new strscpy_pad() since the commit 458a3bf82df4
("lib/string: Add strscpy_pad() function") which will always
NUL-terminate the string, and avoid possibly leak data through the ring
buffer where non-admin account might enable these events through perf.
Fixes: fd1483fe1f9f ("net/mlx5: Add support for FW reporter dump")
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Minor conflict in r8169, bug fix had two versions in net
and net-next, take the net-next hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend struct flow_block_offload with "unlocked_driver_cb" flag to allow
registering and unregistering block hardware offload callbacks that do not
require caller to hold rtnl lock. Extend tcf_block with additional
lockeddevcnt counter that is incremented for each non-unlocked driver
callback attached to device. This counter is necessary to conditionally
obtain rtnl lock before calling hardware callbacks in following patches.
Register mlx5 tc block offload callbacks as "unlocked".
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Return code value could be non deterministic in case of wrong size read.
With this patch, if such error occurs, set rc to be -EIO.
In addition, mlx5_hv_config_common() supports reading of
HV_CONFIG_BLOCK_SIZE_MAX bytes only, fix to early return error with
bad input.
Fixes: 913d14e86657 ("net/mlx5: Add wrappers for HyperV PCIe operations")
Reported-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dump WQE shall not include Ethernet segment. Define mlx5e_dump_wqe to be
used for "Dump WQEs" instead of sharing it with the general mlx5e_tx_wqe
layout.
Fixes: d2ead1f360e8 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
For TLS WQEs, metadata info did not include num_bytes. Due to this issue,
tx_tls_dump_bytes counter did not increment.
Modify tx_fill_wi() to fill num bytes. When it is called for non-traffic
WQE, zero is expected.
Fixes: d2ead1f360e8 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When fw fatal error occurs, poll health() first detects and reports on a
fw error. Afterwards, it detects and reports on the fw fatal error
itself.
That can cause a long delay in fw fatal error handling which waits in a
queue for the fw error handling to be finished. The fw error handle will
try asking for fw core dump command while fw in fatal state may not
respond and driver will wait for command timeout.
Changing the flow to detect and handle first fw fatal errors and only if
no fatal error detected look for a fw error to handle.
Fixes: d1bf0e2cc4a6 ("net/mlx5: Report devlink health on FW issues")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Crdump repeats itself every chunk of 256bytes.
That is due to bug of missing progressing offset while copying the data
from buffer to devlink_fmsg.
Fixes: 9b1f29823605 ("net/mlx5: Add support for FW fatal reporter dump")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
HV VHCA stats agent is responsible on running a preiodic rx/tx
packets/bytes stats update. Currently the supported format is version
MLX5_HV_VHCA_STATS_VERSION. Block ID 1 is dedicated for statistics data
transfer from the VF to the PF.
The reporter fetch the statistics data from all opened channels, fill it
in a buffer and send it to mlx5_hv_vhca_write_agent.
As the stats layer should include some metadata per block (sequence and
offset), the HV VHCA layer shall modify the buffer before actually send it
over block 1.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Control agent is responsible over of the control block (ID 0). It should
update the PF via this block about every capability change. In addition,
upon block 0 invalidate, it should activate all other supported agents
with data requests from the PF.
Upon agent create/destroy, the invalidate callback of the control agent
is being called in order to update the PF driver about this change.
The control agent is an integral part of HV VHCA and will be created
and destroy as part of the HV VHCA init/cleanup flow.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HV VHCA is a layer which provides PF to VF communication channel based on
HyperV PCI config channel. It implements Mellanox's Inter VHCA control
communication protocol. The protocol contains control block in order to
pass messages between the PF and VF drivers, and data blocks in order to
pass actual data.
The infrastructure is agent based. Each agent will be responsible of
contiguous buffer blocks in the VHCA config space. This infrastructure will
bind agents to their blocks, and those agents can only access read/write
the buffer blocks assigned to them. Each agent will provide three
callbacks (control, invalidate, cleanup). Control will be invoked when
block-0 is invalidated with a command that concerns this agent. Invalidate
callback will be invoked if one of the blocks assigned to this agent was
invalidated. Cleanup will be invoked before the agent is being freed in
order to clean all of its open resources or deferred works.
Block-0 serves as the control block. All execution commands from the PF
will be written by the PF over this block. VF will ack on those by
writing on block-0 as well. Its format is described by struct
mlx5_hv_vhca_control_block layout.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add wrapper functions for HyperV PCIe read / write /
block_invalidate_register operations. This will be used as an
infrastructure in the downstream patch for software communication.
This will be enabled by default if CONFIG_PCI_HYPERV_INTERFACE is set.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow tracing neigh state during neigh update task that is executed on
workqueue and is scheduled by neigh state change event.
Usage example:
># cd /sys/kernel/debug/tracing
># echo mlx5:mlx5e_rep_neigh_update >> set_event
># cat trace
...
kworker/u48:7-2221 [009] ...1 1475.387435: mlx5e_rep_neigh_update:
netdev: ens1f0 MAC: 24:8a:07:9a:17:9a IPv4: 1.1.1.10 IPv6: ::ffff:1.1.1.10 neigh_connected=1
Added corresponding documentation in
Documentation/networking/device-driver/mellanox/mlx5.rst
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Dmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Allow tracing result of neigh used value update task that is executed
periodically on workqueue.
Usage example:
># cd /sys/kernel/debug/tracing
># echo mlx5:mlx5e_tc_update_neigh_used_value >> set_event
># cat trace
...
kworker/u48:4-8806 [009] ...1 55117.882428: mlx5e_tc_update_neigh_used_value:
netdev: ens1f0 IPv4: 1.1.1.10 IPv6: ::ffff:1.1.1.10 neigh_used=1
Added corresponding documentation in
Documentation/networking/device-driver/mellanox/mlx5.rst
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Dmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Implemented following tracepoints:
1. Configure flower (mlx5e_configure_flower)
2. Delete flower (mlx5e_delete_flower)
3. Stats flower (mlx5e_stats_flower)
Usage example:
># cd /sys/kernel/debug/tracing
># echo mlx5:mlx5e_configure_flower >> set_event
># cat trace
...
tc-6535 [019] ...1 2672.404466: mlx5e_configure_flower: cookie=0000000067874a55 actions= REDIRECT
Added corresponding documentation in
Documentation/networking/device-driver/mellanox/mlx5.rst
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
To remove dependency on rtnl lock and prevent neigh update code from
accessing uninitialized flows when executing concurrently with tc, extend
mlx5e_tc_flow with 'init_done' completion. Modify helper
mlx5e_take_all_encap_flows() to wait for flow completion after obtaining
reference to it. Modify mlx5e_tc_encap_flows_del() and
mlx5e_tc_encap_flows_add() to skip flows that don't have OFFLOADED flag
set, which can happen if concurrent flow initialization failed.
This commit finishes neigh update refactoring for concurrent execution
started in previous change in this series.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In order to remove dependency on rtnl lock and allow neigh update workqueue
task to execute concurrently with tc, refactor mlx5e_rep_neigh_update() for
concurrent execution:
- Lock encap table when accessing encap entry to prevent concurrent
changes. To do this properly, the initial encap state check is moved from
mlx5e_rep_neigh_update() into mlx5e_rep_update_flows() to be performed
under encap_tbl_lock protection.
- Wait for encap to be fully initialized before accessing it by means of
'res_ready' completion.
- Add mlx5e_take_all_encap_flows() helper which is used to construct a
temporary list of flows and efi indexes that is used to access current
encap data in flow which can be attached to multiple encaps
simultaneously. Release the flows from temporary list after
encap_tbl_lock critical section. This is necessary because
mlx5e_flow_put() can't be called while holding encap_tbl_lock.
- Modify mlx5e_tc_encap_flows_add() and mlx5e_tc_encap_flows_del() to work
with user-provided list of flows built by mlx5e_take_all_encap_flows(),
instead of traversing encap flow list directly.
This is first step in complex neigh update refactoring, which is finished
by following commit in this series.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In order to remove dependency on rtnl lock and allow neigh used value
update workqueue task to execute concurrently with tc, refactor
mlx5e_tc_update_neigh_used_value() for concurrent execution:
- Lock encap table when accessing encap entry to prevent concurrent
changes.
- Save offloaded encap flows to temporary list and release them after encap
entry is updated. Add mlx5e_put_encap_flow_list() helper which is
intended to be shared with neigh update code in following patch in this
series. This is necessary because mlx5e_flow_put() can't be called while
holding encap_tbl_lock.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Rcu-ify mlx5e_neigh_hash_entry->encap_list by changing operations on encap
list to their rcu counterparts and extending encap structure with rcu_head
to free the encap instances after rcu grace period. Use rcu read lock when
traversing encap list. Implement helper mlx5e_get_next_valid_encap()
function that is used by mlx5e_tc_update_neigh_used_value() to safely
iterate over valid entries of nhe->encap_list.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
To remove dependency on rtnl lock, always take neigh update encap lock when
modifying neigh update hash table and list. Originally, this lock was only
used to synchronize with netevent handler function, which is called from bh
context and cannot use rtnl lock for synchronization. Take lock in encap
entry attach function to prevent concurrent modifications of neigh update
hash table and list.
Taking the encap lock when creating new nhe introduces a problem that we
need to allocate new entry with sleeping GFP_KERNEL flag while holding a
spinlock. However, since previous patch in this series has already
converted lookup in netevent handler function to user rcu read lock instead
of encap lock, we can safely convert the lock type to mutex.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
To remove dependency on rtnl lock and to allow unlocked iteration over list
of neigh hash entries, extend nhe with rcu. Change operations on neigh list
to their rcu counterparts and free neigh hash entry with rcu timeout.
Introduce mlx5e_get_next_nhe() helper that is used to iterate over rcu
neigh list with reference to nhe taken.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Neigh entry has reference counter, however it is only used when scheduling
neigh update event. In all other cases reference to neigh entry is not
taken while working with it. Neigh code relies on synchronization provided
by rtnl lock and uses encap list size as implicit reference counter.
To remove dependency on rtnl lock, always take reference to neigh entry
while using it. Remove neigh entry from hash table and delete it only when
reference counter reaches zero. This can result spurious neigh update
events, when there is an event on entry that has zero encaps attached.
However, such events are rare and properly handled by neigh update handler.
Extend encap entry with reference to neigh hash entry in order to be able
to directly release it when encap is detached, instead of lookup nhe by key
through hash table. Extend nhe with reference to device priv structure to
guarantee correctness when nhe is used with stack devices, bond setup, in
which case it is non-trivial to determine correct device when releasing the
nhe.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
As a preparation for following refactoring that removes rtnl lock
dependency from neigh hash entry handlers, extract code that enqueues neigh
update work into standalone function. This commit doesn't change
functionality.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Register supported packet traps (layer 2 drops only, currently) and
associated trap group with devlink during driver initialization.
The amount of traffic generated by these packet drop traps is capped at
10Kpps to ensure the CPU is not overwhelmed by incoming packets.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Discard trap groups are defined in a different enum so that they could
all share the same policer ID: MLXSW_REG_HTGT_TRAP_GROUP_MAX + 1.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the trap IDs used to report layer 2 drops.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Subsequent patches will add discard traps support in mlxsw. The driver
cannot configure such traps with a normal trap action, but needs to use
exception trap action, which also increments an error counter.
On the other hand, when these traps are initialized or set to drop
action, they should use the default drop action set by the firmware.
This guarantees that when the feature is disabled we get the exact same
behavior as before the feature was introduced.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Up until now the action of a trap was never changed during its lifetime.
This is going to change by subsequent patches that will allow devlink to
control the action of certain traps.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use different namespaces for bypass and switchdev loopback because they
have different priorities and default table miss action requirement:
1. bypass: with multiple priorities support, and
MLX5_FLOW_TABLE_MISS_ACTION_DEF as the default table miss action;
2. switchdev loopback: with single priority support, and
MLX5_FLOW_TABLE_MISS_ACTION_SWITCH_DOMAIN as the default table miss
action.
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
|
|
Currently all the namespaces under the same steering domain share the same
default table miss action, however in some situations (e.g., RDMA RX)
different actions are required. This patch adds a per-namespace default
table miss action instead of using the miss action of the steering domain.
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
|
|
Fix documentation of mlx5_eq_enable/disable to cleanup compiler warnings.
drivers/net/ethernet/mellanox/mlx5/core//eq.c:334:
warning: Function parameter or member 'dev' not described in 'mlx5_eq_enable'
warning: Function parameter or member 'eq' not described in 'mlx5_eq_enable'
warning: Function parameter or member 'nb' not described in 'mlx5_eq_enable'
drivers/net/ethernet/mellanox/mlx5/core//eq.c:355:
warning: Function parameter or member 'dev' not described in 'mlx5_eq_disable'
warning: Function parameter or member 'eq' not described in 'mlx5_eq_disable'
warning: Function parameter or member 'nb' not described in 'mlx5_eq_disable'
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add missing include file to avoid compiler warnings:
drivers/net/ethernet/mellanox/mlx5/core//lib/crypto.c:6:5:
warning: no previous prototype for ‘mlx5_create_encryption_key’
6 | int mlx5_create_encryption_key(struct mlx5_core_dev *mdev,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/mellanox/mlx5/core//lib/crypto.c:60:6:
warning: no previous prototype for ‘mlx5_destroy_encryption_key’
60 | void mlx5_destroy_encryption_key(struct mlx5_core_dev *mdev, ...
Fixes: 45d3b55dc665 ("net/mlx5: Add crypto library to support create/destroy encryption key")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Previously, mlx5_cleanup_fc_stats() would cleanup the flow counter
pool beofre releasing all the counters to it, which would result in
flow counter bulks not getting freed. Resolve this by changing the
order in which elements of fc_stats are cleaned up, so that the flow
counter pool is cleaned up after all the counters are released.
Also move cleanup actions for freeing the bulk query memory and
destroying the idr to the end of mlx5_cleanup_fc_stats().
Signed-off-by: Gavi Teitz <gavi@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Recent rtnl lock dependency refactoring changed encap entry attach code to
insert encap entry to hash table before it was fully initialized in order
to allow concurrent tc users to wait on completion for encap entry to
finish initialization. That change required all the users of encap entry to
obtain reference to it first and for caller that creates encap to put
reference to it on error, instead of freeing the entry memory directly.
However, releasing reference to such encap entry that wasn't fully
initialized causes NULL pointer dereference in
mlx5e_rep_encap_entry_detach() which expects e->out_dev to be set and encap
to be attached to nhe:
[ 1092.454517] BUG: unable to handle page fault for address: 00000000000420e8
[ 1092.454571] #PF: supervisor read access in kernel mode
[ 1092.454602] #PF: error_code(0x0000) - not-present page
[ 1092.454632] PGD 800000083032c067 P4D 800000083032c067 PUD 84107d067 PMD 0
[ 1092.454673] Oops: 0000 [#1] SMP PTI
[ 1092.454697] CPU: 20 PID: 22393 Comm: tc Not tainted 5.3.0-rc3+ #589
[ 1092.454733] Hardware name: Supermicro SYS-2028TP-DECR/X10DRT-P, BIOS 2.0b 03/30/2017
[ 1092.454806] RIP: 0010:mlx5e_rep_encap_entry_detach+0x1c/0x630 [mlx5_core]
[ 1092.454845] Code: be f4 ff ff ff e9 11 ff ff ff 0f 1f 40 00 0f 1f 44 00 00 55 48 89 e5 41 57 41 56 41 55 41 54 49 89 fc 53 48 89 f3 48 83 ec 30 <48> 8b 87 28 16 04 00 48 89 f7 48 05 d0 03 00 00 48 89
45 c8 e8 cb
[ 1092.454942] RSP: 0018:ffffb6f08421f5a0 EFLAGS: 00010286
[ 1092.454974] RAX: 0000000000000000 RBX: ffff8ab668644e00 RCX: ffffb6f08421f56c
[ 1092.455013] RDX: ffff8ab668644e40 RSI: ffff8ab668644e00 RDI: 0000000000000ac0
[ 1092.455053] RBP: ffffb6f08421f5f8 R08: 0000000000000001 R09: 0000000000000000
[ 1092.455092] R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000ac0
[ 1092.455131] R13: 00000000ffffff9b R14: ffff8ab63f200ac0 R15: ffff8ab668644e40
[ 1092.455171] FS: 00007fa195bdc480(0000) GS:ffff8ab66fa00000(0000) knlGS:0000000000000000
[ 1092.455216] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1092.455249] CR2: 00000000000420e8 CR3: 0000000867522001 CR4: 00000000001606e0
[ 1092.455288] Call Trace:
[ 1092.455315] ? __mutex_unlock_slowpath+0x4d/0x2a0
[ 1092.455365] mlx5e_encap_dealloc.isra.0+0x31/0x60 [mlx5_core]
[ 1092.455424] mlx5e_tc_add_fdb_flow+0x596/0x750 [mlx5_core]
[ 1092.455484] __mlx5e_add_fdb_flow+0x152/0x210 [mlx5_core]
[ 1092.455534] mlx5e_configure_flower+0x4d5/0xe30 [mlx5_core]
[ 1092.455574] tc_setup_cb_call+0x67/0xb0
[ 1092.455601] fl_hw_replace_filter+0x142/0x300 [cls_flower]
[ 1092.455639] fl_change+0xd24/0x1bdb [cls_flower]
[ 1092.455675] tc_new_tfilter+0x3e0/0x970
[ 1092.455709] ? tc_del_tfilter+0x720/0x720
[ 1092.455735] rtnetlink_rcv_msg+0x389/0x4b0
[ 1092.455763] ? netlink_deliver_tap+0x95/0x400
[ 1092.455791] ? rtnl_dellink+0x2d0/0x2d0
[ 1092.455817] netlink_rcv_skb+0x49/0x110
[ 1092.455844] netlink_unicast+0x171/0x200
[ 1092.455872] netlink_sendmsg+0x224/0x3f0
[ 1092.455901] sock_sendmsg+0x5e/0x60
[ 1092.455924] ___sys_sendmsg+0x2ae/0x330
[ 1092.455950] ? task_work_add+0x43/0x50
[ 1092.455976] ? fput_many+0x45/0x80
[ 1092.456004] ? __lock_acquire+0x248/0x18e0
[ 1092.456033] ? find_held_lock+0x2b/0x80
[ 1092.456058] ? task_work_run+0x7b/0xd0
[ 1092.456085] __sys_sendmsg+0x59/0xa0
[ 1092.457013] do_syscall_64+0x5c/0xb0
[ 1092.457924] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 1092.458842] RIP: 0033:0x7fa195da27b8
[ 1092.459918] Code: 89 02 48 c7 c0 ff ff ff ff eb bb 0f 1f 80 00 00 00 00 f3 0f 1e fa 48 8d 05 65 8f 0c 00 8b 00 85 c0 75 17 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 58 c3 0f 1f 80 00 00 00 00 48 83
ec 28 89 54
[ 1092.462634] RSP: 002b:00007fff94409298 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
[ 1092.464011] RAX: ffffffffffffffda RBX: 000000005d515b0e RCX: 00007fa195da27b8
[ 1092.465391] RDX: 0000000000000000 RSI: 00007fff94409300 RDI: 0000000000000003
[ 1092.466761] RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000006
[ 1092.468121] R10: 0000000000404ec2 R11: 0000000000000246 R12: 0000000000000001
[ 1092.469456] R13: 0000000000480640 R14: 0000000000000016 R15: 0000000000000001
[ 1092.470766] Modules linked in: act_mirred act_tunnel_key cls_flower dummy vxlan ip6_udp_tunnel udp_tunnel sch_ingress nfsv3 nfs_acl nfs lockd grace fscache tun bridge stp llc sunrpc rdma_ucm rdma_cm
iw_cm ib_cm mlx5_ib ib_uverbs ib_core intel_rapl_msr intel_rapl_common sb_edac x86_pkg_temp_thermal intel_powerclamp coretemp mlx5_core kvm_intel kvm irqbypass crct10dif_pclmul mei_me crc32_pclmul crc32
c_intel igb iTCO_wdt ghash_clmulni_intel ses mlxfw intel_cstate iTCO_vendor_support ptp intel_uncore lpc_ich pps_core mei i2c_i801 joydev intel_rapl_perf ioatdma enclosure ipmi_ssif pcspkr dca wmi ipmi_
si ipmi_devintf ipmi_msghandler acpi_pad acpi_power_meter ast i2c_algo_bit drm_vram_helper ttm drm_kms_helper drm mpt3sas raid_class scsi_transport_sas
[ 1092.479618] CR2: 00000000000420e8
[ 1092.481214] ---[ end trace ce2e0f4d9a67f604 ]---
To fix the issue, set e->compl_result to positive value after encap was
initialized successfully. Check e->compl_result value in
mlx5e_encap_dealloc() and only detach and dealloc encap if the value is
positive.
Fixes: d589e785baf5 ("net/mlx5e: Allow concurrent creation of encap entries")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add support for report and recovery from error on completion on RQ by
setting the queue back to ready state. Handle only errors with a
syndrome indicating the RQ might enter error state and could be
recovered.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
David S. Miller
Petr Machata
Ido Schimmel
Shalom Toledo
Amit Cohen
Marina Varshaver
Aya Levin
Moshe Shemesh
Maxim Mikityanskiy
Tariq Toukan
Erez Alfasi
Saeed Mahameed
Michael Guralnik
Qian Cai
Vlad Buslov
Eran Ben Elisha
Dmytro Linkin
Mark Zhang
Gavi Teitz