| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Remove unnecessary CONFIG_PCI_IOV wrapping in ice_set_pf_caps. None
of the data structures accessed within the block are wrapped with
this flag. When CONFIG_PCI_IOV is undefined, pf->num_vfs_supported
will be 0 anyway.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
ice_dev_onetime_setup contains driver workarounds needed for
firmware limitations. These issues have now been resolved in newer
NVMs so remove the function.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently we compare the value we are about to write to the Rx tail
register with the previous value of next_to_use. The problem with this
is we only write tail on 8 descriptor boundaries, but next_to_use is
updated whenever we clean Rx descriptors. Fix this by comparing the
value we are about to write to tail with the previously written tail
value. This will prevent duplicate Rx tail bumps.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Display all of the supported and advertised link modes based on the PHY
capability with media.
Displaying all supported modes is more informative then only displaying
the current link mode.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When switching between FW and SW LLDP mode, the
number of configured TLV apps in the driver's
DCB configuration is getting out of synch with
what lldpad thinks is configured. This is causing
a problem when shutting down lldpad. The cleanup
is trying to delete TLV apps that are not defined
in the kernel.
Since the driver is keeping an accurate account
of the apps defined, use the drivers number of
apps to determine if there is an app to delete.
If the number of apps is <= 1, then do not
attempt to delete.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The function ice_dcb_rebuild had some logic
flaws in it, and also didn't differentiate
between FW and SW modes needs.
For FW flow, the willing setting was being
forced to OFF and left that way. Unwilling
in DCB FW mode is not a supported model.
Leave the config alone and use the return value
from the set command to determine if setting the
config was successful.
The SW DCB flow does not need to need to register
for MIB change events (as they are not used in
SW mode).
Use !is_sw_lldp checks to only perform FW specific
task while in FW mode.
Also adding a reapplication of the current DCB
config after a link event. Some NVMs are not
maintaining their DCB configs across link events.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This allows you to specify the type of rgmii-id that will enable phy
internal delay in ethernet phy-mode.
This adds all RGMII cases to all of get_pinmode() except LD11, because LD11
SoC doesn't support RGMII due to the constraint of the hardware. When RGMII
phy mode is specified in the devicetree for LD11, the driver will abort
with an error.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent months, our customer reported several kernel crashes all
preceding with following message:
NETDEV WATCHDOG: eth2 (enic): transmit queue 0 timed out
Error message of one of those crashes:
BUG: unable to handle kernel paging request at ffffffffa007e090
After analyzing severl vmcores, I found that most of crashes are
caused by memory corruption. And all the corrupted memory areas
are overwritten by data of network packets. Moreover, I also found
that the tx queues were enabled over watchdog reset.
After going through the source code, I found that in enic_stop(),
the tx queues stopped by netif_tx_disable() could be woken up over
a small time window between netif_tx_disable() and the
napi_disable() by the following code path:
napi_poll->
enic_poll_msix_wq->
vnic_cq_service->
enic_wq_service->
netif_wake_subqueue(enic->netdev, q_number)->
test_and_clear_bit(__QUEUE_STATE_DRV_XOFF, &txq->state)
In turn, upper netowrk stack could queue skb to ENIC NIC though
enic_hard_start_xmit(). And this might introduce some race condition.
Our customer comfirmed that this kind of kernel crash doesn't occur over
90 days since they applied this patch.
Signed-off-by: Firo Yang <firo.yang@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
comp_ctx can be NULL in a very rare case when an admin command is executed
during the execution of ena_remove().
The bug scenario is as follows:
* ena_destroy_device() sets the comp_ctx to be NULL
* An admin command is executed before executing unregister_netdev(),
this can still happen because our device can still receive callbacks
from the netdev infrastructure such as ethtool commands.
* When attempting to access the comp_ctx, the bug occurs since it's set
to NULL
Fix:
Added a check that comp_ctx is not NULL
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Up till kernel 4.11 there was no enum defined for crc32 hash in ethtool,
thus the xor enum was used for supporting crc32.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As the name suggests ETH_RSS_HASH_NO_CHANGE is received upon changing
the key or indirection table using ethtool while keeping the same hash
function.
Also add a function for retrieving the current hash function from
the ena-com layer.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Saeed Bshara <saeedb@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function ena_com_ind_tbl_convert_from_device() has an overflow
bug as explained below. Either way, this function is not needed at
all since we don't retrieve the indirection table from the device
at any point which means that this conversion is not needed.
The bug:
The for loop iterates over all io_sq_queues, when passing the actual
number of used queues the io_sq_queues[i].idx equals 0 since they are
uninitialized which results in the following code to be executed till
the end of the loop:
dev_idx_to_host_tbl[0] = i;
This results dev_idx_to_host_tbl[0] in being equal to
ENA_TOTAL_NUM_QUEUES - 1.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The indirection table has the indices of the Rx queues. When we store it
during set indirection operation, we convert the indices to our internal
representation of the indices.
Our internal representation of the indices is: even indices for Tx and
uneven indices for Rx, where every Tx/Rx pair are in a consecutive order
starting from 0. For example if the driver has 3 queues (3 for Tx and 3
for Rx) then the indices are as follows:
0 1 2 3 4 5
Tx Rx Tx Rx Tx Rx
The BUG:
The issue is that when we satisfy a get request for the indirection
table, we don't convert the indices back to the original representation.
The FIX:
Simply apply the inverse function for the indices of the indirection
table after we set it.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device receives, stores and retrieves the hash function value as bits
and not as their enum value.
The bug:
* In ena_com_set_hash_function() we set
cmd.u.flow_hash_func.selected_func to the bit value of rss->hash_func.
(1 << rss->hash_func)
* In ena_com_get_hash_function() we retrieve the hash function and store
it's bit value in rss->hash_func. (Now the bit value of rss->hash_func
is stored in rss->hash_func instead of it's enum value)
The fix:
This commit fixes the issue by converting the retrieved hash function
values from the device to the matching enum value of the set bit using
ffs(). ffs() finds the first set bit's index in a word. Since the function
returns 1 for the LSB's index, we need to subtract 1 from the returned
value (note that BIT(0) is 1).
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On old hardware, getting / setting the hash function is not supported while
gettting / setting the indirection table is.
This commit enables us to still show the indirection table on older
hardwares by setting the hash function and key to NULL.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently we allocate the key whether the device supports setting the
key or not. This commit adds a check to the allocation function and
handles the error accordingly.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bug description:
When running "ethtool -x <if_name>" the key shows up as all zeros.
When we use "ethtool -X <if_name> hfunc toeplitz hkey <some:random:key>" to
set the key and then try to retrieve it using "ethtool -x <if_name>" then
we return the correct key because we return the one we saved.
Bug cause:
We don't fetch the key from the device but instead return the key
that we have saved internally which is by default set to zero upon
allocation.
Fix:
This commit fixes the issue by initializing the key to a random value
using netdev_rss_key_fill().
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current implementation of the driver calls skb_tx_timestamp()to add a
software tx timestamp to the skb, however the software-transmit capability
is not reported in ethtool -T.
This commit updates the ethtool structure to report the software-transmit
capability in ethtool -T using the standard ethtool_op_get_ts_info().
This function reports all software timestamping capabilities (tx and rx),
as well as setting phc_index = -1. phc_index is the index of the PTP
hardware clock device that will be used for hardware timestamps. Since we
don't have such a device in ENA, using the default -1 value is the correct
setting.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Ezequiel Lara Gomez <ezegomez@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
>From the documentation of round_jiffies():
"Rounds a time delta in the future (in jiffies) up or down to
(approximately) full seconds. This is useful for timers for which
the exact time they fire does not matter too much, as long as
they fire approximately every X seconds.
By rounding these timers to whole seconds, all such timers will fire
at the same time, rather than at various times spread out. The goal
of this is to have the CPU wake up less, which saves power."
There are 2 parts to this patch:
================================
Part 1:
-------
In our case we need timer_service to be called approximately every
X=1 seconds, and the exact time does not matter, so using round_jiffies()
is the right way to go.
Therefore we add round_jiffies() to the mod_timer() in ena_timer_service().
Part 2:
-------
round_jiffies() is used in check_for_missing_keep_alive() when
getting the jiffies of the expiration of the keep_alive timeout. Here it
is actually a mistake to use round_jiffies() because we want the exact
time when keep_alive should expire and not an approximate rounded time,
which can cause early, false positive, timeouts.
Therefore we remove round_jiffies() in the calculation of
keep_alive_expired() in check_for_missing_keep_alive().
Fixes: 82ef30f13be0 ("net: ena: add hardware hints capability to the driver")
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When ethtool -X is called without an hkey, ena_com_fill_hash_function()
is called with key=NULL, which is passed to memcpy causing a crash.
This commit fixes this issue by checking key is not NULL.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit d9d6a9aed3f6 ("i40e: Fix virtchnl_queue_select bitmap
validation") introduced a necessary change for verifying how queue
bitmaps from the iavf driver get validated. Unfortunately, the
conditional was reversed. Fix this.
Fixes: d9d6a9aed3f6 ("i40e: Fix virtchnl_queue_select bitmap validation")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Unbalanced locking in mwifiex_process_country_ie, from Brian Norris.
2) Fix thermal zone registration in iwlwifi, from Andrei
Otcheretianski.
3) Fix double free_irq in sgi ioc3 eth, from Thomas Bogendoerfer.
4) Use after free in mptcp, from Florian Westphal.
5) Use after free in wireguard's root_remove_peer_lists, from Eric
Dumazet.
6) Properly access packets heads in bonding alb code, from Eric
Dumazet.
7) Fix data race in skb_queue_len(), from Qian Cai.
8) Fix regression in r8169 on some chips, from Heiner Kallweit.
9) Fix XDP program ref counting in hv_netvsc, from Haiyang Zhang.
10) Certain kinds of set link netlink operations can cause a NULL deref
in the ipv6 addrconf code. Fix from Eric Dumazet.
11) Don't cancel uninitialized work queue in drop monitor, from Ido
Schimmel.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
net: thunderx: use proper interface type for RGMII
mt76: mt7615: fix max_nss in mt7615_eeprom_parse_hw_cap
bpf: Improve bucket_log calculation logic
selftests/bpf: Test freeing sockmap/sockhash with a socket in it
bpf, sockhash: Synchronize_rcu before free'ing map
bpf, sockmap: Don't sleep while holding RCU lock on tear-down
bpftool: Don't crash on missing xlated program instructions
bpf, sockmap: Check update requirements after locking
drop_monitor: Do not cancel uninitialized work item
mlxsw: spectrum_dpipe: Add missing error path
mlxsw: core: Add validation of hardware device types for MGPIR register
mlxsw: spectrum_router: Clear offload indication from IPv6 nexthops on abort
selftests: mlxsw: Add test cases for local table route replacement
mlxsw: spectrum_router: Prevent incorrect replacement of local table routes
net: dsa: microchip: enable module autoprobe
ipv6/addrconf: fix potential NULL deref in inet6_set_link_af()
dpaa_eth: support all modes with rate adapting PHYs
net: stmmac: update pci platform data to use phy_interface
net: stmmac: xgmac: fix missing IFF_MULTICAST checki in dwxgmac2_set_filter
net: stmmac: fix missing IFF_MULTICAST check in dwmac4_set_filter
...
|
|
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
|
|
The configuration of the OCTEONTX XCV_DLL_CTL register via
xcv_init_hw() is such that the RGMII RX delay is bypassed
leaving the RGMII TX delay enabled in the MAC:
/* Configure DLL - enable or bypass
* TX no bypass, RX bypass
*/
cfg = readq_relaxed(xcv->reg_base + XCV_DLL_CTL);
cfg &= ~0xFF03;
cfg |= CLKRX_BYP;
writeq_relaxed(cfg, xcv->reg_base + XCV_DLL_CTL);
This would coorespond to a interface type of PHY_INTERFACE_MODE_RGMII_RXID
and not PHY_INTERFACE_MODE_RGMII.
Fixing this allows RGMII PHY drivers to do the right thing (enable
RX delay in the PHY) instead of erroneously enabling both delays in the
PHY.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2020-02-07
The following pull-request contains BPF updates for your *net* tree.
We've added 15 non-merge commits during the last 10 day(s) which contain
a total of 12 files changed, 114 insertions(+), 31 deletions(-).
The main changes are:
1) Various BPF sockmap fixes related to RCU handling in the map's tear-
down code, from Jakub Sitnicki.
2) Fix macro state explosion in BPF sk_storage map when calculating its
bucket_log on allocation, from Martin KaFai Lau.
3) Fix potential BPF sockmap update race by rechecking socket's established
state under lock, from Lorenz Bauer.
4) Fix crash in bpftool on missing xlated instructions when kptr_restrict
sysctl is set, from Toke Høiland-Jørgensen.
5) Fix i40e's XSK wakeup code to return proper error in busy state and
various misc fixes in xdpsock BPF sample code, from Maciej Fijalkowski.
6) Fix the way modifiers are skipped in BTF in the verifier while walking
pointers to avoid program rejection, from Alexei Starovoitov.
7) Fix Makefile for runqslower BPF tool to i) rebuild on libbpf changes and
ii) to fix undefined reference linker errors for older gcc version due to
order of passed gcc parameters, from Yulia Kartseva and Song Liu.
8) Fix a trampoline_count BPF kselftest warning about missing braces around
initializer, from Andrii Nakryiko.
9) Fix up redundant "HAVE" prefix from large INSN limit kernel probe in
bpftool, from Michal Rostecki.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case devlink_dpipe_entry_ctx_prepare() failed, release RTNL that was
previously taken and free the memory allocated by
mlxsw_sp_erif_entry_prepare().
Fixes: 2ba5999f009d ("mlxsw: spectrum: Add Support for erif table entries access")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When reading the number of gearboxes from the hardware, the driver does
not validate the returned 'device type' field. The driver can therefore
wrongly assume that the queried devices are gearboxes.
On Spectrum-3 systems that support different types of devices, this can
prevent the driver from loading, as it will try to query the
temperature sensors from devices which it assumes are gearboxes and in
fact are not.
For example:
[ 218.129230] mlxsw_minimal 2-0048: Reg cmd access status failed (status=7(bad parameter))
[ 218.138282] mlxsw_minimal 2-0048: Reg cmd access failed (reg_id=900a(mtmp),type=write)
[ 218.147131] mlxsw_minimal 2-0048: Failed to setup temp sensor number 256
[ 218.534480] mlxsw_minimal 2-0048: Fail to register core bus
[ 218.540714] mlxsw_minimal: probe of 2-0048 failed with error -5
Fix this by validating the 'device type' field.
Fixes: 2e265a8b6c094 ("mlxsw: core: Extend hwmon interface with inter-connect temperature attributes")
Fixes: f14f4e621b1b4 ("mlxsw: core: Extend thermal core with per inter-connect device thermal zones")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unlike IPv4, in IPv6 there is no unique structure to represent the
nexthop and both the route and nexthop information are squashed to the
same structure ('struct fib6_info'). In order to improve resource
utilization the driver consolidates identical nexthop groups to the same
internal representation of a nexthop group.
Therefore, when the offload indication of a nexthop changes, the driver
needs to iterate over all the linked fib6_info and toggle their offload
flag accordingly.
During abort, all the routes are removed from the device and unlinked
from their nexthop group. The offload indication is cleared just before
the group is destroyed, but by that time no fib6_info is linked to the
group and the offload indication remains set.
Fix this by clearing the offload indication just before dropping the
reference from the nexthop.
Fixes: ee5a0448e72b ("mlxsw: spectrum_router: Set hardware flags for routes")
Reported-by: Alex Kushnarov <alexanderk@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Alex Kushnarov <alexanderk@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver uses the same table to represent both the main and local
routing tables. Prevent routes in the main table from replacing routes
in the local table to reflect the fact that the local table is consulted
first during lookup.
Fixes: b6a1d871d37a ("mlxsw: spectrum_router: Start using new IPv4 route notifications")
Fixes: dacad7b34b59 ("mlxsw: spectrum_router: Start using new IPv6 route notifications")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stop removing modes that are not supported on the system interface
when the connected PHY is capable of rate adaptation. This addresses
an issue with the LS1046ARDB board 10G interface no longer working
with an 1G link partner after autonegotiation support was added
for the Aquantia PHY on board in
commit 09c4c57f7bc4 ("net: phy: aquantia: add support for auto-negotiation configuration")
Before this commit the values advertised by the PHY were not
influenced by the dpaa_eth driver removal of system-side unsupported
modes as the aqr_config_aneg() was basically a no-op. After this
commit, the modes removed by the dpaa_eth driver were no longer
advertised thus autonegotiation with 1G link partners failed.
Reported-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The recent patch to support passive mode converter did not take care the
phy interface configuration in PCI platform data. Hence, converting all
the PCI platform data from plat->interface to plat->phy_interface as the
default mode is meant for PHY.
Fixes: 0060c8783330 ("net: stmmac: implement support for passive mode converters via dt")
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Tested-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without checking for IFF_MULTICAST flag, it is wrong to assume multicast
filtering is always enabled. By checking against IFF_MULTICAST, now
the driver behaves correctly when the multicast support is toggled by below
command:-
ip link set <devname> multicast off|on
Fixes: 0efedbf11f07a ("net: stmmac: xgmac: Fix XGMAC selftests")
Signed-off-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without checking for IFF_MULTICAST flag, it is wrong to assume multicast
filtering is always enabled. By checking against IFF_MULTICAST, now
the driver behaves correctly when the multicast support is toggled by below
command:-
ip link set <devname> multicast off|on
Fixes: 477286b53f55 ("stmmac: add GMAC4 core support")
Signed-off-by: Verma, Aashish <aashishx.verma@intel.com>
Tested-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should always do a read of current value of XGMAC_VLAN_TAG instead of
directly overwriting the register value.
Fixes: 3cd1cfcba26e2 ("net: stmmac: Implement VLAN Hash Filtering in XGMAC")
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It should always do a read of current value of GMAC_VLAN_TAG instead of
directly overwriting the register value.
Fixes: c1be0022df0d ("net: stmmac: Add VLAN HASH filtering support in GMAC4+")
Signed-off-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It forgot to reduce the value of the variable retry in a while loop
in the ethqos_configure() function. It may cause an endless loop and
without timeout.
Fixes: a7c30e62d4b8 ("net: stmmac: Add driver for Qualcomm ethqos")
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Deprecate the generic TLS cap bit, use the new TX-specific
TLS cap bit instead.
Fixes: a12ff35e0fb7 ("net/mlx5: Introduce TLS TX offload hardware bits and structures")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
For a cyclic work queue, when not requesting a completion per WQE,
a single CQE might indicate the completion of several WQEs.
However, in case some WQE in the batch causes an error, then an error
completion is issued, breaking the batch, and pointing to the offending
WQE in the wqe_counter field.
Hence, WQE-specific error CQE handling (like printing, breaking, etc...)
should be performed only for the last WQE in batch.
Fixes: 130c7b46c93d ("net/mlx5e: TX, Dump WQs wqe descriptors on CQE with error events")
Fixes: fd9b4be8002c ("net/mlx5e: RX, Support multiple outstanding UMR posts")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
SA context is allocated at mlx5_fpga_ipsec_create_sa_ctx,
however the counterpart mlx5_fpga_ipsec_delete_sa_ctx function
nullifies sa_ctx pointer without freeing the memory allocated,
hence the memory leak.
Fix by free SA context when the SA is released.
Fixes: d6c4f0298cec ("net/mlx5: Refactor accel IPSec code")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The function mlx5_fpga_esp_validate_xfrm_attrs is wrongly used
with negative negation as zero value indicates success but it
used as failure return value instead.
Fix by remove the unary not negation operator.
Fixes: 05564d0ae075 ("net/mlx5: Add flow-steering commands for FPGA IPSec implementation")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
free_match_list could be called when the flow table is already
locked. We need to pass this notation to tree_put_node.
It fixes the following lockdep warnning:
[ 1797.268537] ============================================
[ 1797.276837] WARNING: possible recursive locking detected
[ 1797.285101] 5.5.0-rc5+ #10 Not tainted
[ 1797.291641] --------------------------------------------
[ 1797.299917] handler10/9296 is trying to acquire lock:
[ 1797.307885] ffff889ad399a0a0 (&node->lock){++++}, at:
tree_put_node+0x1d5/0x210 [mlx5_core]
[ 1797.319694]
[ 1797.319694] but task is already holding lock:
[ 1797.330904] ffff889ad399a0a0 (&node->lock){++++}, at:
nested_down_write_ref_node.part.33+0x1a/0x60 [mlx5_core]
[ 1797.344707]
[ 1797.344707] other info that might help us debug this:
[ 1797.356952] Possible unsafe locking scenario:
[ 1797.356952]
[ 1797.368333] CPU0
[ 1797.373357] ----
[ 1797.378364] lock(&node->lock);
[ 1797.384222] lock(&node->lock);
[ 1797.390031]
[ 1797.390031] *** DEADLOCK ***
[ 1797.390031]
[ 1797.403003] May be due to missing lock nesting notation
[ 1797.403003]
[ 1797.414691] 3 locks held by handler10/9296:
[ 1797.421465] #0: ffff889cf2c5a110 (&block->cb_lock){++++}, at:
tc_setup_cb_add+0x70/0x250
[ 1797.432810] #1: ffff88a030081490 (&comp->sem){++++}, at:
mlx5_devcom_get_peer_data+0x4c/0xb0 [mlx5_core]
[ 1797.445829] #2: ffff889ad399a0a0 (&node->lock){++++}, at:
nested_down_write_ref_node.part.33+0x1a/0x60 [mlx5_core]
[ 1797.459913]
[ 1797.459913] stack backtrace:
[ 1797.469436] CPU: 1 PID: 9296 Comm: handler10 Kdump: loaded Not
tainted 5.5.0-rc5+ #10
[ 1797.480643] Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS
2.4.3 01/17/2017
[ 1797.491480] Call Trace:
[ 1797.496701] dump_stack+0x96/0xe0
[ 1797.502864] __lock_acquire.cold.63+0xf8/0x212
[ 1797.510301] ? lockdep_hardirqs_on+0x250/0x250
[ 1797.517701] ? mark_held_locks+0x55/0xa0
[ 1797.524547] ? quarantine_put+0xb7/0x160
[ 1797.531422] ? lockdep_hardirqs_on+0x17d/0x250
[ 1797.538913] lock_acquire+0xd6/0x1f0
[ 1797.545529] ? tree_put_node+0x1d5/0x210 [mlx5_core]
[ 1797.553701] down_write+0x94/0x140
[ 1797.560206] ? tree_put_node+0x1d5/0x210 [mlx5_core]
[ 1797.568464] ? down_write_killable_nested+0x170/0x170
[ 1797.576925] ? del_hw_flow_group+0xde/0x1f0 [mlx5_core]
[ 1797.585629] tree_put_node+0x1d5/0x210 [mlx5_core]
[ 1797.593891] ? free_match_list.part.25+0x147/0x170 [mlx5_core]
[ 1797.603389] free_match_list.part.25+0xe0/0x170 [mlx5_core]
[ 1797.612654] _mlx5_add_flow_rules+0x17e2/0x20b0 [mlx5_core]
[ 1797.621838] ? lock_acquire+0xd6/0x1f0
[ 1797.629028] ? esw_get_prio_table+0xb0/0x3e0 [mlx5_core]
[ 1797.637981] ? alloc_insert_flow_group+0x420/0x420 [mlx5_core]
[ 1797.647459] ? try_to_wake_up+0x4c7/0xc70
[ 1797.654881] ? lock_downgrade+0x350/0x350
[ 1797.662271] ? __mutex_unlock_slowpath+0xb1/0x3f0
[ 1797.670396] ? find_held_lock+0xac/0xd0
[ 1797.677540] ? mlx5_add_flow_rules+0xdc/0x360 [mlx5_core]
[ 1797.686467] mlx5_add_flow_rules+0xdc/0x360 [mlx5_core]
[ 1797.695134] ? _mlx5_add_flow_rules+0x20b0/0x20b0 [mlx5_core]
[ 1797.704270] ? irq_exit+0xa5/0x170
[ 1797.710764] ? retint_kernel+0x10/0x10
[ 1797.717698] ? mlx5_eswitch_set_rule_source_port.isra.9+0x122/0x230
[mlx5_core]
[ 1797.728708] mlx5_eswitch_add_offloaded_rule+0x465/0x6d0 [mlx5_core]
[ 1797.738713] ? mlx5_eswitch_get_prio_range+0x30/0x30 [mlx5_core]
[ 1797.748384] ? mlx5_fc_stats_work+0x670/0x670 [mlx5_core]
[ 1797.757400] mlx5e_tc_offload_fdb_rules.isra.27+0x24/0x90 [mlx5_core]
[ 1797.767665] mlx5e_tc_add_fdb_flow+0xaf8/0xd40 [mlx5_core]
[ 1797.776886] ? mlx5e_encap_put+0xd0/0xd0 [mlx5_core]
[ 1797.785562] ? mlx5e_alloc_flow.isra.43+0x18c/0x1c0 [mlx5_core]
[ 1797.795353] __mlx5e_add_fdb_flow+0x2e2/0x440 [mlx5_core]
[ 1797.804558] ? mlx5e_tc_update_neigh_used_value+0x8c0/0x8c0
[mlx5_core]
[ 1797.815093] ? wait_for_completion+0x260/0x260
[ 1797.823272] mlx5e_configure_flower+0xe94/0x1620 [mlx5_core]
[ 1797.832792] ? __mlx5e_add_fdb_flow+0x440/0x440 [mlx5_core]
[ 1797.842096] ? down_read+0x11a/0x2e0
[ 1797.849090] ? down_write+0x140/0x140
[ 1797.856142] ? mlx5e_rep_indr_setup_block_cb+0xc0/0xc0 [mlx5_core]
[ 1797.866027] tc_setup_cb_add+0x11a/0x250
[ 1797.873339] fl_hw_replace_filter+0x25e/0x320 [cls_flower]
[ 1797.882385] ? fl_hw_destroy_filter+0x1c0/0x1c0 [cls_flower]
[ 1797.891607] fl_change+0x1d54/0x1fb6 [cls_flower]
[ 1797.899772] ? __rhashtable_insert_fast.constprop.50+0x9f0/0x9f0
[cls_flower]
[ 1797.910728] ? lock_downgrade+0x350/0x350
[ 1797.918187] ? __radix_tree_lookup+0xa5/0x130
[ 1797.926046] ? fl_set_key+0x1590/0x1590 [cls_flower]
[ 1797.934611] ? __rhashtable_insert_fast.constprop.50+0x9f0/0x9f0
[cls_flower]
[ 1797.945673] tc_new_tfilter+0xcd1/0x1240
[ 1797.953138] ? tc_del_tfilter+0xb10/0xb10
[ 1797.960688] ? avc_has_perm_noaudit+0x92/0x320
[ 1797.968721] ? avc_has_perm_noaudit+0x1df/0x320
[ 1797.976816] ? avc_has_extended_perms+0x990/0x990
[ 1797.985090] ? mark_lock+0xaa/0x9e0
[ 1797.991988] ? match_held_lock+0x1b/0x240
[ 1797.999457] ? match_held_lock+0x1b/0x240
[ 1798.006859] ? find_held_lock+0xac/0xd0
[ 1798.014045] ? symbol_put_addr+0x40/0x40
[ 1798.021317] ? rcu_read_lock_sched_held+0xd0/0xd0
[ 1798.029460] ? tc_del_tfilter+0xb10/0xb10
[ 1798.036810] rtnetlink_rcv_msg+0x4d5/0x620
[ 1798.044236] ? rtnl_bridge_getlink+0x460/0x460
[ 1798.052034] ? lockdep_hardirqs_on+0x250/0x250
[ 1798.059837] ? match_held_lock+0x1b/0x240
[ 1798.067146] ? find_held_lock+0xac/0xd0
[ 1798.074246] netlink_rcv_skb+0xc6/0x1f0
[ 1798.081339] ? rtnl_bridge_getlink+0x460/0x460
[ 1798.089104] ? netlink_ack+0x440/0x440
[ 1798.096061] netlink_unicast+0x2d4/0x3b0
[ 1798.103189] ? netlink_attachskb+0x3f0/0x3f0
[ 1798.110724] ? _copy_from_iter_full+0xda/0x370
[ 1798.118415] netlink_sendmsg+0x3ba/0x6a0
[ 1798.125478] ? netlink_unicast+0x3b0/0x3b0
[ 1798.132705] ? netlink_unicast+0x3b0/0x3b0
[ 1798.139880] sock_sendmsg+0x94/0xa0
[ 1798.146332] ____sys_sendmsg+0x36c/0x3f0
[ 1798.153251] ? copy_msghdr_from_user+0x165/0x230
[ 1798.160941] ? kernel_sendmsg+0x30/0x30
[ 1798.167738] ___sys_sendmsg+0xeb/0x150
[ 1798.174411] ? sendmsg_copy_msghdr+0x30/0x30
[ 1798.181649] ? lock_downgrade+0x350/0x350
[ 1798.188559] ? rcu_read_lock_sched_held+0xd0/0xd0
[ 1798.196239] ? __fget+0x21d/0x320
[ 1798.202335] ? do_dup2+0x2a0/0x2a0
[ 1798.208499] ? lock_downgrade+0x350/0x350
[ 1798.215366] ? __fget_light+0xd6/0xf0
[ 1798.221808] ? syscall_trace_enter+0x369/0x5d0
[ 1798.229112] __sys_sendmsg+0xd3/0x160
[ 1798.235511] ? __sys_sendmsg_sock+0x60/0x60
[ 1798.242478] ? syscall_trace_enter+0x233/0x5d0
[ 1798.249721] ? syscall_slow_exit_work+0x280/0x280
[ 1798.257211] ? do_syscall_64+0x1e/0x2e0
[ 1798.263680] do_syscall_64+0x72/0x2e0
[ 1798.269950] entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fixes: bd71b08ec2ee ("net/mlx5: Support multiple updates of steering rules in parallel")
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
After a number of suspend and resume cycles, it is possible for the RBUF
to be stuck in Wake-on-LAN mode, despite the MPD enable bit being
cleared which instructed the RBUF to exit that mode.
Avoid creating that problematic condition by clearing the RX_EN and
TX_EN bits in the UniMAC prior to disable the Magic Packet Detector
logic which is guaranteed to make the RBUF exit Wake-on-LAN mode.
Fixes: 83e82f4c706b ("net: systemport: add Wake-on-LAN support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It turned out that on low performance systems the original change can
cause lower tx performance. On a N3450-based mini-PC tx performance
in iperf3 was reduced from 950Mbps to ~900Mbps. Therefore effectively
revert the original change, just use pcie_set_readrq() now instead of
changing the PCIe capability register directly.
Fixes: 2df49d365498 ("r8169: remove fiddling with the PCIe max read request size")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move rx_dropped and rx_errors counters in mvneta_pcpu_stats in order to
avoid possible races updating statistics
Fixes: 562e2f467e71 ("net: mvneta: Improve the buffer allocation method for SWBM")
Fixes: dc35a10f68d3 ("net: mvneta: bm: add support for hardware buffer management")
Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added debugfs entry to show the tls stats.
Signed-off-by: Devulapally Shiva Krishna <shiva@chelsio.com>
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Return -EAGAIN instead of -ENETDOWN to provide a slightly milder
information to user space so that an application will know to retry the
syscall when __I40E_CONFIG_BUSY bit is set on pf->state.
Fixes: b3873a5be757 ("net/i40e: Fix concurrency issues between config flow and XSK")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Link: https://lore.kernel.org/bpf/20200205045834.56795-2-maciej.fijalkowski@intel.com
|
|
commit cedeac9df4b8 ("qed: Add support for Timestamping the unicast
PTP packets.") handles the timestamping of L4 ptp packets only.
This patch adds driver changes to detect/timestamp both L2/L4 unicast
PTP packets.
Fixes: cedeac9df4b8 ("qed: Add support for Timestamping the unicast PTP packets.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
GEM_MAX_TX_LEN currently resolves to 0x3FF8 for any IP version supporting
TSO with full 14bits of length field in payload descriptor. But an IP
errata causes false amba_error (bit 6 of ISR) when length in payload
descriptors is specified above 16387. The error occurs because the DMA
falsely concludes that there is not enough space in SRAM for incoming
payload. These errors were observed continuously under stress of large
packets using iperf on a version where SRAM was 16K for each queue. This
errata will be documented shortly and affects all versions since TSO
functionality was added. Hence limit the max length to 0x3FC0 (rounded).
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IP TSO implementation does NOT require the length to be a
multiple of 8. That is only a requirement for UFO as per IP
documentation. Hence, exit macb_features_check function in the
beginning if the protocol is not UDP. Only when it is UDP,
proceed further to the alignment checks. Update comments to
reflect the same. Also remove dead code checking for protocol
TCP when calculating header length.
Fixes: 1629dd4f763c ("cadence: Add LSO support.")
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The receive frame length calculation uses a wrong mask to calculate the
length of the received frames.
Per spec table 4-1 the length is contained in the FL (Frame Length)
field in bits 30:16.
This didn't show up as an issue so far since frames were limited to
1500 bytes which falls within the 11 bit window.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Anirudh Venkataramanan
Brett Creeley
Paul Greenwalt
Dave Ertman
Kunihiko Hayashi
Firo Yang
Arthur Kiyanovski
Sameeh Jubran
Linus Torvalds
Tim Harvey
David S. Miller
Ido Schimmel
Vadim Pasternak
Madalin Bucur
Voon Weifeng
Tan, Tee Min
Verma, Aashish
Ong Boon Leong
Dejin Zheng
Tariq Toukan
Raed Salem
Maor Gottlieb
Florian Fainelli
Heiner Kallweit
Lorenzo Bianconi
Devulapally Shiva Krishna
Maciej Fijalkowski
Sudarsana Reddy Kalluru
Harini Katakam
Moritz Fischer