Age | Commit message (Collapse) | Author | Files | Lines |
|
The debug prints of hardware status and operations will look better
if SPI device name is printed. The benefit of that is a possibility
to distinguish the actual hardware when more than one is installed
on the system.
Convert appropriate printk(KERN_DEBUG) to dev_print(KERN_DEBUG, &spi->dev).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of using open coded printk(KERN_<LEVEL>) switch the driver to use
dev_<level> macros.
Note, the device name will be printed in full, which is beneficial when
more than one card installed on the system.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use ether_addr_copy() instead of memcpy() to copy the mac address.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eliminate some boilerplate code by using module_spi_driver() instead of
->init() / ->exit(), moving the salient bits from ->init() into ->probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When dev_<level>() macros are used against SPI device, the driver's name
is printed as well. No need to duplicate this explicitly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace open coded netdev_<level>() macros.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ->probe() and ->remove() stages can be easily debugged with
initcall_debug or function tracer. There is no need to repeat the same
explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the DT-specific of_get_mac_address() function with
device_get_mac_address, which works on both DT and ACPI platforms.
This change makes it easier to add ACPI support.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix sparse warning:
drivers/net/ethernet/pasemi/pasemi_mac.c:1842:5: warning:
symbol 'pasemi_mac_init_module' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix sparse warning:
drivers/net/ethernet/hisilicon/hns3/hns3vf/hclgevf_main.c:407:6:
warning: symbol 'hclgevf_update_link_mode' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix sparse warning:
drivers/net/ethernet/ibm/ibmveth.c:96:21:
warning: symbol 'ibmveth_stats' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ibmvnic driver currently reports a fixed value for both speed and
duplex settings regardless of the actual backing device that is being
used. By adding support to the QUERY_PHYS_PARMS command defined by the
PAPR+ we can query the current physical port state and report the proper
values for these feilds.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Murilo Fossa Vicentini <muvic@linux.ibm.com>
Reviewed-by: Mauro S. M. Rodrigues <maurosr@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TCP/UDP checksum validity was propagated to skb
only if IP checksum is valid.
But for IPv6 there is no validity as there is no checksum in IPv6.
This patch propagates TCP/UDP checksum validity regardless of IP checksum.
Fixes: 018423e90bee ("net: ethernet: aquantia: Add ring support code")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bug that Stan reported is as follows. After a restart, a 16-bit NIC
may be incorrectly identified as a 32-bit NIC and stop working.
mac8390 slot.E: Memory length resource not found, probing
mac8390 slot.E: Farallon EtherMac II-C (type farallon)
mac8390 slot.E: MAC 00:00:c5:30:c2:99, IRQ 61, 32 KB shared memory at 0xfeed0000, 32-bit access.
The bug never arises after a cold start and only intermittently after a
warm start. (I didn't investigate why the bug is intermittent.)
It turns out that memcpy_toio() is deprecated and memcmp_withio() also
has issues. Replacing these calls with mmio accessors fixes the problem.
Reported-and-tested-by: Stan Johnson <userm57@yahoo.com>
Fixes: 2964db0f5904 ("m68k: Mac DP8390 update")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are several statements that contain extra spacing in
the indentation; clean this up by removing spaces. Also
add { } braces on if statement to keep to kernel coding
style.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a statement that is indented incorrectly; replace
spaces with a tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netdev_alloc_skb can fail and return a NULL pointer which is
dereferenced without a check. The patch avoids such a scenario.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When sending non-linear skbs with jumbo frames, we set up the non-paged
data and mark that as a last segment, although the paged fragments are
also prepared. This will stall the TX queue and trigger a watchdog warning
(a simple reproducer is to run an iperf client mode TCP test with a large
MTU - networking fails instantly).
Fix by checking if the skb is non-linear.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 0e80bdc9a72d ("stmmac: first frame prep at the end of xmit
routine") overlooked jumbo frames when re-ordering the code, and as a
result the own bit was not getting set anymore for the first jumbo frame
descriptor. Commit 487e2e22ab79 ("net: stmmac: Set OWN bit for jumbo
frames") tried to fix this, but now the bit is getting set too early and
the DMA may start while we are still setting up the remaining descriptors.
And with the chain mode the own bit remains still unset.
Fix by setting the own bit at the end of xmit also with jumbo frames.
Fixes: 0e80bdc9a72d ("stmmac: first frame prep at the end of xmit routine")
Fixes: 487e2e22ab79 ("net: stmmac: Set OWN bit for jumbo frames")
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
"More fixes in the queue:
1) Netfilter nat can erroneously register the device notifier twice,
fix from Florian Westphal.
2) Use after free in nf_tables, from Pablo Neira Ayuso.
3) Parallel update of steering rule fix in mlx5 river, from Eli
Britstein.
4) RX processing panic in lan743x, fix from Bryan Whitehead.
5) Use before initialization of TCP_SKB_CB, fix from Christoph Paasch.
6) Fix locking in SRIOV mode of mlx4 driver, from Jack Morgenstein.
7) Fix TX stalls in lan743x due to mishandling of interrupt ACKing
modes, from Bryan Whitehead.
8) Fix infoleak in l2tp_ip6_recvmsg(), from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
pptp: dst_release sk_dst_cache in pptp_sock_destruct
MAINTAINERS: GENET & SYSTEMPORT: Add internal Broadcom list
l2tp: fix infoleak in l2tp_ip6_recvmsg()
net/tls: Inform user space about send buffer availability
net_sched: return correct value for *notify* functions
lan743x: Fix TX Stall Issue
net/mlx4_core: Fix qp mtt size calculation
net/mlx4_core: Fix locking in SRIOV mode when switching between events and polling
net/mlx4_core: Fix reset flow when in command polling mode
mlxsw: minimal: Initialize base_mac
mlxsw: core: Prevent duplication during QSFP module initialization
net: dwmac-sun8i: fix a missing check of of_get_phy_mode
net: sh_eth: fix a missing check of of_get_phy_mode
net: 8390: fix potential NULL pointer dereferences
net: fujitsu: fix a potential NULL pointer dereference
net: qlogic: fix a potential NULL pointer dereference
isdn: hfcpci: fix potential NULL pointer dereference
Documentation: devicetree: add a new optional property for port mac address
net: rocker: fix a potential NULL pointer dereference
net: qlge: fix a potential NULL pointer dereference
...
|
|
It has been observed that tx queue may stall while downloading
from certain web sites (example www.speedtest.net)
The cause has been tracked down to a corner case where
the tx interrupt vector was disabled automatically, but
was not re enabled later.
The lan743x has two mechanisms to enable/disable individual
interrupts. Interrupts can be enabled/disabled by individual
source, and they can also be enabled/disabled by individual
vector which has been mapped to the source. Both must be
enabled for interrupts to work properly.
The TX code path, primarily uses the interrupt enable/disable of
the TX source bit, while leaving the vector enabled all the time.
However, while investigating this issue it was noticed that
the driver requested the use of the vector auto clear feature.
The test above revealed a case where the vector enable was
cleared unintentionally.
This patch fixes the issue by deleting the lines that request
the vector auto clear feature to be used.
Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Calculation of qp mtt size (in function mlx4_RST2INIT_wrapper)
ultimately depends on function roundup_pow_of_two.
If the amount of memory required by the QP is less than one page,
roundup_pow_of_two is called with argument zero. In this case, the
roundup_pow_of_two result is undefined.
Calling roundup_pow_of_two with a zero argument resulted in the
following stack trace:
UBSAN: Undefined behaviour in ./include/linux/log2.h:61:13
shift exponent 64 is too large for 64-bit type 'long unsigned int'
CPU: 4 PID: 26939 Comm: rping Tainted: G OE 4.19.0-rc1
Hardware name: Supermicro X9DR3-F/X9DR3-F, BIOS 3.2a 07/09/2015
Call Trace:
dump_stack+0x9a/0xeb
ubsan_epilogue+0x9/0x7c
__ubsan_handle_shift_out_of_bounds+0x254/0x29d
? __ubsan_handle_load_invalid_value+0x180/0x180
? debug_show_all_locks+0x310/0x310
? sched_clock+0x5/0x10
? sched_clock+0x5/0x10
? sched_clock_cpu+0x18/0x260
? find_held_lock+0x35/0x1e0
? mlx4_RST2INIT_QP_wrapper+0xfb1/0x1440 [mlx4_core]
mlx4_RST2INIT_QP_wrapper+0xfb1/0x1440 [mlx4_core]
Fix this by explicitly testing for zero, and returning one if the
argument is zero (assuming that the next higher power of 2 in this case
should be one).
Fixes: c82e9aa0a8bc ("mlx4_core: resource tracking for HCA resources used by guests")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In procedures mlx4_cmd_use_events() and mlx4_cmd_use_polling(), we need to
guarantee that there are no FW commands in progress on the comm channel
(for VFs) or wrapped FW commands (on the PF) when SRIOV is active.
We do this by also taking the slave_cmd_mutex when SRIOV is active.
This is especially important when switching from event to polling, since we
free the command-context array during the switch. If there are FW commands
in progress (e.g., waiting for a completion event), the completion event
handler will access freed memory.
Since the decision to use comm_wait or comm_poll is taken before grabbing
the event_sem/poll_sem in mlx4_comm_cmd_wait/poll, we must take the
slave_cmd_mutex as well (to guarantee that the decision to use events or
polling and the call to the appropriate cmd function are atomic).
Fixes: a7e1f04905e5 ("net/mlx4_core: Fix deadlock when switching between polling and event fw commands")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As part of unloading a device, the driver switches from
FW command event mode to FW command polling mode.
Part of switching over to polling mode is freeing the command context array
memory (unfortunately, currently, without NULLing the command context array
pointer).
The reset flow calls "complete" to complete all outstanding fw commands
(if we are in event mode). The check for event vs. polling mode here
is to test if the command context array pointer is NULL.
If the reset flow is activated after the switch to polling mode, it will
attempt (incorrectly) to complete all the commands in the context array --
because the pointer was not NULLed when the driver switched over to polling
mode.
As a result, we have a use-after-free situation, which results in a
kernel crash.
For example:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff876c4a8e>] __wake_up_common+0x2e/0x90
PGD 0
Oops: 0000 [#1] SMP
Modules linked in: netconsole nfsv3 nfs_acl nfs lockd grace ...
CPU: 2 PID: 940 Comm: kworker/2:3 Kdump: loaded Not tainted 3.10.0-862.el7.x86_64 #1
Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS 090006 04/28/2016
Workqueue: events hv_eject_device_work [pci_hyperv]
task: ffff8d1734ca0fd0 ti: ffff8d17354bc000 task.ti: ffff8d17354bc000
RIP: 0010:[<ffffffff876c4a8e>] [<ffffffff876c4a8e>] __wake_up_common+0x2e/0x90
RSP: 0018:ffff8d17354bfa38 EFLAGS: 00010082
RAX: 0000000000000000 RBX: ffff8d17362d42c8 RCX: 0000000000000000
RDX: 0000000000000001 RSI: 0000000000000003 RDI: ffff8d17362d42c8
RBP: ffff8d17354bfa70 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000298 R11: ffff8d173610e000 R12: ffff8d17362d42d0
R13: 0000000000000246 R14: 0000000000000000 R15: 0000000000000003
FS: 0000000000000000(0000) GS:ffff8d1802680000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 00000000f16d8000 CR4: 00000000001406e0
Call Trace:
[<ffffffff876c7adc>] complete+0x3c/0x50
[<ffffffffc04242f0>] mlx4_cmd_wake_completions+0x70/0x90 [mlx4_core]
[<ffffffffc041e7b1>] mlx4_enter_error_state+0xe1/0x380 [mlx4_core]
[<ffffffffc041fa4b>] mlx4_comm_cmd+0x29b/0x360 [mlx4_core]
[<ffffffffc041ff51>] __mlx4_cmd+0x441/0x920 [mlx4_core]
[<ffffffff877f62b1>] ? __slab_free+0x81/0x2f0
[<ffffffff87951384>] ? __radix_tree_lookup+0x84/0xf0
[<ffffffffc043a8eb>] mlx4_free_mtt_range+0x5b/0xb0 [mlx4_core]
[<ffffffffc043a957>] mlx4_mtt_cleanup+0x17/0x20 [mlx4_core]
[<ffffffffc04272c7>] mlx4_free_eq+0xa7/0x1c0 [mlx4_core]
[<ffffffffc042803e>] mlx4_cleanup_eq_table+0xde/0x130 [mlx4_core]
[<ffffffffc0433e08>] mlx4_unload_one+0x118/0x300 [mlx4_core]
[<ffffffffc0434191>] mlx4_remove_one+0x91/0x1f0 [mlx4_core]
The fix is to set the command context array pointer to NULL after freeing
the array.
Fixes: f5aef5aa3506 ("net/mlx4_core: Activate reset flow upon fatal command cases")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently base_mac is not initialized which causes wrong reporting of
zeroed parent_id to userspace. Fix this by initializing base_mac
properly.
Fixes: c100e47caa8e ("mlxsw: minimal: Add ethtool support")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Verify during thermal initialization if QSFP module's entry is already
configured in order to prevent duplication.
Such scenario could happen in case two switch drivers (PCI and I2C
based) coexist and if after boot, splitting configuration is applied
for some ports and then I2C based driver is re-probed.
In such case after reboot same QSFP module, associated with split will
be discovered by I2C based driver few times, and it will cause a crash.
It could happen for example on system equipped with BMC (Baseboard
Management Controller), running I2C based driver, when the next steps
are performed:
- System boot
- Host side configures port spilt.
- BMC side is rebooted.
Fixes: 6a79507cfe94 ("mlxsw: core: Extend thermal module with per QSFP module thermal zones")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
of_get_phy_mode may fail and return a negative error code;
the fix checks the return value of of_get_phy_mode and
returns -EINVAL of it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
of_get_phy_mode may fail and return a negative error code;
the fix checks the return value of of_get_phy_mode and
returns NULL of it fails.
Fixes: b356e978e92f ("sh_eth: add device tree support")
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case ioremap fails, the fix releases resources and returns
to avoid NULL pointer dereferences.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case ioremap fails, the fix releases the pcmcia window and
returns -ENOMEM to avoid the NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case create_singlethread_workqueue fails, the fix returns
-ENOMEM to avoid NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-03-11
For -stable v5.0:
('net/mlx5e: Fix access to non-existing receive queue')
('net/mlx5e: Properly get the PF number phys port name ndo')
('net/mlx5: Fix multiple updates of steering rules in parallel')
('net/mlx5: Avoid panic when setting vport mac, getting vport config')
('net/mlx5: Avoid panic when setting vport rate')
('net/mlx5e: IPoIB, Fix RX checksum statistics update')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case kzalloc fails, the fix releases resources and returns
NOTIFY_BAD to avoid NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case alloc_ordered_workqueue fails, the fix returns
-ENOMEM to avoid NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case alloc_ordered_workqueue fails, the fix reports the error
and returns -ENOMEM.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case octeon_alloc_soft_command fails, the fix reports the
error and returns to avoid NULL pointer dereferences.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It has been noticed that running the speed test at
www.speedtest.net occasionally causes a kernel panic.
Investigation revealed that under this test RX buffer allocation
sometimes fails and returns NULL. But the lan743x driver did
not handle this case.
This patch fixes this issue by attempting to allocate a buffer
before sending the new rx packet to the OS. If the allocation
fails then the new rx packet is dropped and the existing buffer
is reused in the DMA ring.
Updates for v2:
Additional 2 locations where allocation was not checked,
has been changed to reuse existing buffer.
Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case octeon_alloc_soft_command fails, the fix reports the
error and returns to avoid NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we try to set VFs rate on a VF (not PF) net device, the kernel
will be crash. The commands are show as below:
$ echo 2 > /sys/class/net/$MLX_PF0/device/sriov_numvfs
$ ip link set $MLX_VF0 vf 0 max_tx_rate 2 min_tx_rate 1
If not applied the first patch ("net/mlx5: Avoid panic when setting
vport mac, getting vport config"), the command:
$ ip link set $MLX_VF0 vf 0 rate 100
can also crash the kernel.
[ 1650.006388] RIP: 0010:mlx5_eswitch_set_vport_rate+0x1f/0x260 [mlx5_core]
[ 1650.007092] do_setlink+0x982/0xd20
[ 1650.007129] __rtnl_newlink+0x528/0x7d0
[ 1650.007374] rtnl_newlink+0x43/0x60
[ 1650.007407] rtnetlink_rcv_msg+0x2a2/0x320
[ 1650.007484] netlink_rcv_skb+0xcb/0x100
[ 1650.007519] netlink_unicast+0x17f/0x230
[ 1650.007554] netlink_sendmsg+0x2d2/0x3d0
[ 1650.007592] sock_sendmsg+0x36/0x50
[ 1650.007625] ___sys_sendmsg+0x280/0x2a0
[ 1650.007963] __sys_sendmsg+0x58/0xa0
[ 1650.007998] do_syscall_64+0x5b/0x180
[ 1650.009438] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: c9497c98901c ("net/mlx5: Add support for setting VF min rate")
Cc: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
If we try to set VFs mac address on a VF (not PF) net device,
the kernel will be crash. The commands are show as below:
$ echo 2 > /sys/class/net/$MLX_PF0/device/sriov_numvfs
$ ip link set $MLX_VF0 vf 0 mac 00:11:22:33:44:00
[exception RIP: mlx5_eswitch_set_vport_mac+41]
[ffffb8b7079e3688] do_setlink at ffffffff8f67f85b
[ffffb8b7079e37a8] __rtnl_newlink at ffffffff8f683778
[ffffb8b7079e3b68] rtnl_newlink at ffffffff8f683a63
[ffffb8b7079e3b90] rtnetlink_rcv_msg at ffffffff8f67d812
[ffffb8b7079e3c10] netlink_rcv_skb at ffffffff8f6b88ab
[ffffb8b7079e3c60] netlink_unicast at ffffffff8f6b808f
[ffffb8b7079e3ca0] netlink_sendmsg at ffffffff8f6b8412
[ffffb8b7079e3d18] sock_sendmsg at ffffffff8f6452f6
[ffffb8b7079e3d30] ___sys_sendmsg at ffffffff8f645860
[ffffb8b7079e3eb0] __sys_sendmsg at ffffffff8f647a38
[ffffb8b7079e3f38] do_syscall_64 at ffffffff8f00401b
[ffffb8b7079e3f50] entry_SYSCALL_64_after_hwframe at ffffffff8f80008c
and
[exception RIP: mlx5_eswitch_get_vport_config+12]
[ffffa70607e57678] mlx5e_get_vf_config at ffffffffc03c7f8f [mlx5_core]
[ffffa70607e57688] do_setlink at ffffffffbc67fa59
[ffffa70607e577a8] __rtnl_newlink at ffffffffbc683778
[ffffa70607e57b68] rtnl_newlink at ffffffffbc683a63
[ffffa70607e57b90] rtnetlink_rcv_msg at ffffffffbc67d812
[ffffa70607e57c10] netlink_rcv_skb at ffffffffbc6b88ab
[ffffa70607e57c60] netlink_unicast at ffffffffbc6b808f
[ffffa70607e57ca0] netlink_sendmsg at ffffffffbc6b8412
[ffffa70607e57d18] sock_sendmsg at ffffffffbc6452f6
[ffffa70607e57d30] ___sys_sendmsg at ffffffffbc645860
[ffffa70607e57eb0] __sys_sendmsg at ffffffffbc647a38
[ffffa70607e57f38] do_syscall_64 at ffffffffbc00401b
[ffffa70607e57f50] entry_SYSCALL_64_after_hwframe at ffffffffbc80008c
Fixes: a8d70a054a718 ("net/mlx5: E-Switch, Disallow vlan/spoofcheck setup if not being esw manager")
Cc: Eli Cohen <eli@mellanox.com>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In case number of channels is changed while interface is down,
RSS indirection table is mistakenly not modified accordingly,
causing access to out-of-range non-existing object.
Fix by updating the RSS indireciton table also in the early
return flow of interface down.
Fixes: fb35c534b788 ("net/mlx5e: Fix NULL pointer derefernce in set channels error flow")
Fixes: bbeb53b8b2c9 ("net/mlx5e: Move RSS params to a dedicated struct")
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Tested-by: Maria Pasechnik <mariap@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Update the RX checksum only if the feature is enabled.
Fixes: 9d6bd752c63c ("net/mlx5e: IPoIB, RX handler")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The function is not being used.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently, we fail to retrieve the PF number in some cases (e.g
single ported cards, lag capability), this further results in a
call trace issued by the rtnetlink code, since the error value
is not -EOPNOTSUPP. Change the implementation to be independent
from the lag code and function properly on both two ports and
single ported cards.
Call Trace:
[ 194.525057] mlx5_core 0000:82:00.0: mlx5_lag_get_pf_num:605:(pid 837): no lag device, can't get pf num
[ 194.525804] WARNING: CPU: 7 PID: 837 at net/core/rtnetlink.c:3457 rtmsg_ifinfo_build_skb+0x131/0x160
[ 194.529952] CPU: 7 PID: 837 Comm: kworker/7:3 Tainted: G W O 5.0.0-rc7+ #3
[ 194.531307] Workqueue: events linkwatch_event
[ 194.531697] RIP: 0010:rtmsg_ifinfo_build_skb+0x131/0x160
[ 194.545007] Call Trace:
[ 194.545406] rtmsg_ifinfo_event.part.29+0x1b/0xb0
[ 194.545810] rtmsg_ifinfo+0x51/0x80
[ 194.546209] netdev_state_change+0xc7/0x110
[ 194.546608] ? dev_valid_name+0x1b0/0x1b0
[ 194.547010] ? __local_bh_enable_ip+0xef/0x1d0
[ 194.547411] ? lockdep_hardirqs_on+0x3ea/0x560
[ 194.547811] ? linkwatch_do_dev+0x9b/0x100
[ 194.548207] linkwatch_do_dev+0x9b/0x100
[ 194.548605] __linkwatch_run_queue+0x244/0x430
[ 194.549014] ? linkwatch_schedule_work+0x100/0x100
[ 194.549412] ? lock_acquire+0x10f/0x2d0
[ 194.549816] linkwatch_event+0x3f/0x50
[ 194.550212] process_one_work+0x7d3/0x1460
Fixes: c12ecc230564 ("net/mlx5e: Move to use common phys port names for vport representors")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
With commit a18e879d4e45 ("net/mlx5e: Annul encap action ordering
requirement") and a use-case of e-switch remote mirroring, the
incremental/stepped FTE removal process done by the fs core got us to
illegal transient states and FW errors:
SET_FLOW_TABLE_ENTRY(0x936) op_mod(0x0) failed, status bad
parameter(0x3), syndrome (0x9c2e40)
To avoid that and improve FTE removal performance, aggregate the FTE's
updates that should be applied. Remove the FTE if it is empty, or apply
one FW update command with the aggregated updates.
Fixes: a18e879d4e45 ("net/mlx5e: Annul encap action ordering requirement")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add a locked flag to the node removal functions to signal if the
parent is already locked from the caller function or not as a pre-step
towards outside lock. Currently always use false with no functional
change.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add modify FTE helper function and use it when deleting a rule, as a
pre-step towards consolidated FTE modification, with no functional
change.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
There might be a condition where the fte found is not active yet. In
this case we should not use it, but continue to search for another, or
allocate a new one.
Fixes: bd71b08ec2ee ("net/mlx5: Support multiple updates of steering rules in parallel")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Pull networking fixes from David Miller:
"First batch of fixes in the new merge window:
1) Double dst_cache free in act_tunnel_key, from Wenxu.
2) Avoid NULL deref in IN_DEV_MFORWARD() by failing early in the
ip_route_input_rcu() path, from Paolo Abeni.
3) Fix appletalk compile regression, from Arnd Bergmann.
4) If SLAB objects reach the TCP sendpage method we are in serious
trouble, so put a debugging check there. From Vasily Averin.
5) Memory leak in hsr layer, from Mao Wenan.
6) Only test GSO type on GSO packets, from Willem de Bruijn.
7) Fix crash in xsk_diag_put_umem(), from Eric Dumazet.
8) Fix VNIC mailbox length in nfp, from Dirk van der Merwe.
9) Fix race in ipv4 route exception handling, from Xin Long.
10) Missing DMA memory barrier in hns3 driver, from Jian Shen.
11) Use after free in __tcf_chain_put(), from Vlad Buslov.
12) Handle inet_csk_reqsk_queue_add() failures, from Guillaume Nault.
13) Return value correction when ip_mc_may_pull() fails, from Eric
Dumazet.
14) Use after free in x25_device_event(), also from Eric"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (72 commits)
gro_cells: make sure device is up in gro_cells_receive()
vxlan: test dev->flags & IFF_UP before calling gro_cells_receive()
net/x25: fix use-after-free in x25_device_event()
isdn: mISDNinfineon: fix potential NULL pointer dereference
net: hns3: fix to stop multiple HNS reset due to the AER changes
ip: fix ip_mc_may_pull() return value
net: keep refcount warning in reqsk_free()
net: stmmac: Avoid one more sometimes uninitialized Clang warning
net: dsa: mv88e6xxx: Set correct interface mode for CPU/DSA ports
rxrpc: Fix client call queueing, waiting for channel
tcp: handle inet_csk_reqsk_queue_add() failures
net: ethernet: sun: Zero initialize class in default case in niu_add_ethtool_tcam_entry
8139too : Add support for U.S. Robotics USR997901A 10/100 Cardbus NIC
fou, fou6: avoid uninit-value in gue_err() and gue6_err()
net: sched: fix potential use-after-free in __tcf_chain_put()
vhost: silence an unused-variable warning
vsock/virtio: fix kernel panic from virtio_transport_reset_no_sock
connector: fix unsafe usage of ->real_parent
vxlan: do not need BH again in vxlan_cleanup()
net: hns3: add dma_rmb() for rx description
...
|