aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet
AgeCommit message (Collapse)AuthorFilesLines
2020-09-11net: hns: use IRQ_NOAUTOEN to avoid irq is enabled due to request_irqBarry Song1-1/+2
Rather than doing request_irq and then disabling the irq immediately, it should be safer to use IRQ_NOAUTOEN flag for the irq. It removes any gap between request_irq() and disable_irq(). Cc: Salil Mehta <salil.mehta@huawei.com> Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Barry Song <song.bao.hua@hisilicon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11net: ethernet: ti: cpsw_new: fix suspend/resumeGrygorii Strashko1-0/+53
Add missed suspend/resume callbacks to properly restore networking after suspend/resume cycle. Fixes: ed3525eda4c4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac") Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11net: ethernet: ti: ale: add support for multi port k3 cpsw versionsGrygorii Strashko1-0/+14
The TI J721E (CPSW9g) ALE version is similar, in general, to Sitara AM3/4/5 CPSW ALE, but has more extended functions and different ALE VLAN entry format. This patch adds support for for multi port TI J721E (CPSW9g) ALE variant. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11net: ethernet: ti: ale: switch to use tables for vlan entry descriptionGrygorii Strashko2-54/+188
The ALE VLAN entries are too much differ between different TI CPSW ALE versions. So, handling them using flags, defines and get/set functions became over-complicated. This patch introduces tables to describe the ALE VLAN entries fields, which are different between TI CPSW ALE versions, and new get/set access functions. It also allows to detect incorrect access to not available ALL entry fields. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11net: ethernet: ti: am65-cpsw: enable hw auto ageingGrygorii Strashko4-6/+70
The AM65x ALE supports HW auto-ageing which can be enabled by programming ageing interval in ALE_AGING_TIMER register. For this CPSW fck_clk frequency has to be know by ALE. This patch extends cpsw_ale_params with bus_freq field and enables ALE HW auto ageing for AM65x CPSW2G ALE version. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11net: ethernet: ti: ale: make usage of ale dev_id mandatoryGrygorii Strashko2-17/+14
Hence all existing driver updated to use ALE dev_id the usage of ale dev_id can be made mandatory and cpsw_ale_create() can be updated to use "features" property from ALE static configuration. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11net: ethernet: ti: am65-cpsw: use dev_id for ale configurationGrygorii Strashko1-2/+1
The previous patch has introduced possibility to select CPSW ALE by using ALE dev_id identifier. Switch TI TI AM65x/J721E CPSW NUSS driver to use dev_id. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11net: netcp: ethss: use dev_id for ale configurationGrygorii Strashko1-10/+8
The previous patch has introduced possibility to select CPSW ALE by using ALE dev_id identifier. Switch TI Keystone 2 NETCP driver to use dev_id and perform clean up by removing "ale_entries" configuration code. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11net: ethernet: ti: cpsw: use dev_id for ale configurationGrygorii Strashko4-10/+1
The previous patch has introduced possibility to select CPSW ALE by using ALE dev_id identifier. Switch TI cpsw driver to use dev_id="cpsw" and perform clean up by removing "ale_entries" configuration code. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11net: ethernet: ti: ale: add static configurationGrygorii Strashko2-0/+83
As existing, as newly introduced CPSW ALE versions have differences in supported features and ALE table formats. Especially it's actual for the recent AM65x/J721E/J7200 SoC and feature AM64x, which supports features like: auto-aging, classifiers, Link aggregation, additional hw filtering, etc. Existing ALE configuration interface is not practical in terms of adding new features and requires consumers to program a lot static parameters. Any attempt to add new options will case endless adding and maintaining different combination of flags and options. Hence CPSW ALE configuration is static and fixed for SoC (or set of SoC) It is reasonable to add support for static ALE configurations inside ALE module. This patch adds static ALE configuration table for different ALE versions and provides option for consumers to select required ALE configuration by providing ALE const char *dev_id identifier. This feature is not enabled by default until existing CPSW drivers will be modified by follow up patches. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11net: ethernet: ti: ale: add cpsw_ale_get_num_entries apiGrygorii Strashko4-5/+14
Add cpsw_ale_get_num_entries() API to return number of ALE table entries and update existing drivers to use it. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11crypto/chcr: move nic TLS functionality to drivers/netRohit Maheshwari13-58/+2434
This patch moves complete nic tls offload (kTLS) code from crypto directory to drivers/net/ethernet/chelsio/inline_crypto/ch_ktls directory. nic TLS is made a separate ULD of cxgb4. Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11hinic: fix rewaking txq after netif_tx_disableLuo bin2-16/+28
When calling hinic_close in hinic_set_channels, all queues are stopped after netif_tx_disable, but some queue may be rewaken in free_tx_poll by mistake while drv is handling tx irq. If one queue is rewaken core may call hinic_xmit_frame to send pkt after netif_tx_disable within a short time which may results in accessing memory that has been already freed in hinic_close. So we call napi_disable before netif_tx_disable in hinic_close to fix this bug. Fixes: 2eed5a8b614b ("hinic: add set_channels ethtool_ops support") Signed-off-by: Luo bin <luobin9@huawei.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queueDavid S. Miller3-18/+43
Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2020-09-09 This series contains updates to i40e and igc drivers. Stefan Assmann changes num_vlans to u16 to fix may be used uninitialized error and propagates error in i40_set_vsi_promisc() for i40e. Vinicius corrects timestamping latency values for i225 devices and accounts for TX timestamping delay for igc. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11sfc: advertise encapsulated offloads on EF10Edward Cree4-0/+104
Necessitates an .ndo_features_check, as the EF10 datapath has several limitations on what it can handle. Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11sfc: implement encapsulated TSO on EF10Edward Cree2-14/+46
>From the 8000 series onwards, EF10 NICs with suitable firmware are able to perform TSO within VXLAN or NVGRE encapsulation. Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11sfc: de-indirect TSO handlingEdward Cree9-37/+46
Remove the tx_queue->handle_tso function pointer, and just use tx_queue->tso_version to decide which function to call, thus removing an indirect call from the fast path. Instead of passing a tso_v2 flag to efx_mcdi_tx_init(), set the desired tx_queue->tso_version before calling it. In efx_mcdi_tx_init(), report back failure to obtain a TSOv2 context by setting tx_queue->tso_version to 0, which will cause the TX path to use the GSO-based fallback. Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11sfc: select inner-csum-offload TX queues for skbs that need itEdward Cree3-2/+29
Won't actually be exercised until we start advertising the corresponding offload features. Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11sfc: create inner-csum queues on EF10 if supportedEdward Cree2-11/+28
If the MC reports the VXLAN_NVGRE datapath capability, then these queues can be used for checksum offload of encapsulated packets. Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11sfc: define inner/outer csum offload TXQ typesEdward Cree7-11/+13
Nothing yet creates inner csum TXQs; just change all references to EFX_TXQ_TYPE_OFFLOAD to the new EFX_TXQ_TYPE_OUTER_CSUM. Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11sfc: decouple TXQ type from labelEdward Cree11-43/+64
Make it possible to have an arbitrary mapping from types to labels, because when we add inner-csum-offload TXQs there will no longer be a convenient nesting hierarchy of NIC types (EF10 will have inner-csum TXQs, while Siena will have HIGHPRI). Correct a misleading comment on efx_hard_start_xmit(). Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11octeontx2-af: Constify npc_kpu_profile_{action,cam}Rikard Falkeborn3-39/+39
These are never modified, so constify them to allow the compiler to place them in read-only memory. This moves about 25kB to read-only memory as seen by the output of the size command. Before: text data bss dec hex filename 296203 65464 1248 362915 589a3 drivers/net/ethernet/marvell/octeontx2/af/octeontx2_af.ko After: text data bss dec hex filename 321003 40664 1248 362915 589a3 drivers/net/ethernet/marvell/octeontx2/af/octeontx2_af.ko Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11sfc: cleanups around efx_alloc_channelEdward Cree2-5/+2
The old_channel argument is never used, so remove it. The function is only called from elsewhere in efx_channels.c, so make it static and remove the declaration from the header file. Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11sfc: remove spurious unreachable return statementEdward Cree1-1/+0
The statement above it already returns, so there is no way to get here. Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11sfc: remove duplicate call to efx_init_channels from EF100 probeEdward Cree1-4/+0
efx_init_struct already calls this, we don't need to do it again. Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11enetc: Fix mdio bus removal on PF probe bailoutClaudiu Manoil1-1/+1
This is the correct resolution for the conflict from merging the "net" tree fix: commit 26cb7085c898 ("enetc: Remove the mdio bus on PF probe bailout") with the "net-next" new work: commit 07095c025ac2 ("net: enetc: Use DT protocol information to set up the ports") that moved mdio bus allocation to an ealier stage of the PF probing routine. Fixes: a57066b1a019 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net") Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11net: ag71xx: add flow control supportOleksij Rempel1-1/+12
Add flow control support. The functionality was tested on AR9331 SoC and confirmed by iperf3 results and HW counters exported over ethtool. Following test configurations was used: iMX6S receiver <--- TL-SG1005D switch <---- AR9331 sender The switch is supporting symmytric flow control: Settings for eth0: Supported ports: [ MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Advertised pause frame use: Symmetric Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Link partner advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full --->> Link partner advertised pause frame use: Symmetric Link partner advertised auto-negotiation: Yes Link partner advertised FEC modes: Not reported Speed: 100Mb/s Duplex: Full Auto-negotiation: on Port: MII PHYAD: 4 Transceiver: external Link detected: yes The iMX6S system was configured to 10Mbit, to let the switch use flow control: - ethtool -s eth0 speed 10 With flow control disabled on AR9331: - ethtool -A eth0 rx off tx off - iperf3 -u -c 172.17.0.1 -b100M -l1472 -t10 [ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams [ 5] 0.00-10.00 sec 66.2 MBytes 55.5 Mbits/sec 0.000 ms 0/47155 (0%) sender [ 5] 0.00-10.04 sec 11.5 MBytes 9.57 Mbits/sec 1.309 ms 38986/47146 (83%) receiver With flow control enabled on AR9331: - ethtool -A eth0 rx on tx on - iperf3 -u -c 172.17.0.1 -b100M -l1472 -t10 [ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams [ 5] 0.00-10.00 sec 15.1 MBytes 12.6 Mbits/sec 0.000 ms 0/10727 (0%) sender [ 5] 0.00-10.05 sec 11.5 MBytes 9.57 Mbits/sec 1.371 ms 2525/10689 (24%) receiver Similar results are get in opposite direction by introducing extra CPU load on AR9331: - chrt 40 dd if=/dev/zero of=/dev/null & Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11net: ag71xx: add ethtool supportOleksij Rempel1-0/+147
Add basic ethtool support. The functionality was tested on AR9331 SoC. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11net: stmmac: set get_rx_header_len() as void for it didn't have any error code to returnLuo Jiaxing4-8/+6
We found the following warning when using W=1 to build kernel: drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:3634:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable] int ret, coe = priv->hw->rx_csum; When digging stmmac_get_rx_header_len(), dwmac4_get_rx_header_len() and dwxgmac2_get_rx_header_len() return 0 only, without any error code to report. Therefore, it's better to define get_rx_header_len() as void. Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11gve: Enable Link Speed Reporting in the driver.David Awogbemila4-1/+56
This change allows the driver to report the device link speed when the ethtool command: ethtool <nic name> is run. Getting the link speed is done via a new admin queue command: ReportLinkSpeed. Reviewed-by: Yangchun Fu <yangchun@google.com> Signed-off-by: David Awogbemila <awogbemila@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11gve: Use link status register to report link statusPatricio Noyola1-3/+21
This makes the driver better aware of the connectivity status of the device. Based on the device's status register, the driver can call netif_carrier_{on,off}. Reviewed-by: Yangchun Fu <yangchun@google.com> Signed-off-by: Patricio Noyola <patricion@google.com> Signed-off-by: David Awogbemila <awogbemila@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11gve: Batch AQ commands for creating and destroying queues.Sagi Shahar3-81/+211
Adds support for batching AQ commands and uses it for creating and destroying queues. Reviewed-by: Yangchun Fu <yangchun@google.com> Signed-off-by: Sagi Shahar <sagis@google.com> Signed-off-by: David Awogbemila <awogbemila@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11gve: NIC stats for report-stats and for ethtoolDavid Awogbemila4-3/+94
This adds per queue NIC stats to ethtool stats and to report-stats. These stats are always exposed to guest whether or not the report-stats flag is turned on. Signed-off-by: David Awogbemila <awogbemila@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11gve: Add Gvnic stats AQ command and ethtool show/set-priv-flags.Kuo Zhao6-31/+368
This adds functionality to report driver stats to Hypervisor. (Users may want to turn this feature off as a matter of privacy so a "report-stats" flag is added as an ethtool priv option. It is also disabled by default.) The hypervisor would trigger a stats report in case "too many" packets dropped; the stats would be useful in debugging stuck queues. A "stats_report_trigger_cnt" stat is added to count the number of times the hypervisor attempts to trigger stats report. A timer is also added so that when report-stats is enabled, stat are updated once every 20 seconds. Reviewed-by: Yangchun Fu <yangchun@google.com> Signed-off-by: Kuo Zhao <kuozhao@google.com> Signed-off-by: David Awogbemila <awogbemila@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11gve: Use dev_info/err instead of netif_info/err.Catherine Sullivan2-14/+11
Update the driver to use dev_info/err instead of netif_info/err. Reviewed-by: Yangchun Fu <yangchun@google.com> Signed-off-by: Catherine Sullivan <csully@google.com> Signed-off-by: David Awogbemila <awogbemila@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11gve: Add stats for gve.Kuo Zhao5-48/+245
Sample output of "ethtool -S <interface-name>" with 1 RX queue and 1 TX queue: NIC statistics: rx_packets: 1039 tx_packets: 37 rx_bytes: 822071 tx_bytes: 4100 rx_dropped: 0 tx_dropped: 0 tx_timeouts: 0 rx_skb_alloc_fail: 0 rx_buf_alloc_fail: 0 rx_desc_err_dropped_pkt: 0 interface_up_cnt: 1 interface_down_cnt: 0 reset_cnt: 0 page_alloc_fail: 0 dma_mapping_error: 0 rx_posted_desc[0]: 1365 rx_completed_desc[0]: 341 rx_bytes[0]: 215094 rx_dropped_pkt[0]: 0 rx_copybreak_pkt[0]: 3 rx_copied_pkt[0]: 3 tx_posted_desc[0]: 6 tx_completed_desc[0]: 6 tx_bytes[0]: 420 tx_wake[0]: 0 tx_stop[0]: 0 tx_event_counter[0]: 6 adminq_prod_cnt: 34 adminq_cmd_fail: 0 adminq_timeouts: 0 adminq_describe_device_cnt: 1 adminq_cfg_device_resources_cnt: 1 adminq_register_page_list_cnt: 16 adminq_unregister_page_list_cnt: 0 adminq_create_tx_queue_cnt: 8 adminq_create_rx_queue_cnt: 8 adminq_destroy_tx_queue_cnt: 0 adminq_destroy_rx_queue_cnt: 0 adminq_dcfg_device_resources_cnt: 0 adminq_set_driver_parameter_cnt: 0 Reviewed-by: Yangchun Fu <yangchun@google.com> Signed-off-by: Kuo Zhao <kuozhao@google.com> Signed-off-by: David Awogbemila <awogbemila@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11gve: Get and set Rx copybreak via ethtoolKuo Zhao1-0/+34
This adds support for getting and setting the RX copybreak value via ethtool. Reviewed-by: Yangchun Fu <yangchun@google.com> Signed-off-by: Kuo Zhao <kuozhao@google.com> Signed-off-by: David Awogbemila <awogbemila@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-11qede: Notify qedr when mtu has changedMichal Kalderon2-1/+20
MTU change on ethtool is currently not supported for iWARP. Notify qedr driver so that appropriate logging can take place. Link: https://lore.kernel.org/r/20200902165741.8355-6-michal.kalderon@marvell.com Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
2020-09-11RDMA/qedr: Remove fbo and zbva from the MRJason Gunthorpe1-10/+2
zbva is always false, so fbo is never read. A 'zero-based-virtual-address' is simply IOVA == 0, and the driver already supports this. Link: https://lore.kernel.org/r/16-v2-270386b7e60b+28f4-umem_1_jgg@nvidia.com Acked-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
2020-09-10net: smc91x: Remove set but not used variable 'status' in smc_phy_configure()Luo Jiaxing1-2/+1
Fixes the following warning when using W=1 to build kernel: drivers/net/ethernet/smsc/smc91x.c: In function ‘smc_phy_configure’: drivers/net/ethernet/smsc/smc91x.c:1039:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable] int status; Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10net: dec: de2104x: Increase receive ring size for TulipLucy Yan1-1/+1
Increase Rx ring size to address issue where hardware is reaching the receive work limit. Before: [ 102.223342] de2104x 0000:17:00.0 eth0: rx work limit reached [ 102.245695] de2104x 0000:17:00.0 eth0: rx work limit reached [ 102.251387] de2104x 0000:17:00.0 eth0: rx work limit reached [ 102.267444] de2104x 0000:17:00.0 eth0: rx work limit reached Signed-off-by: Lucy Yan <lucyyan@google.com> Reviewed-by: Moritz Fischer <mdf@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10net: hns: Fix a kernel-doc warning in hinic_hw_eqs.cWang Hai1-1/+1
Fixes the following W=1 kernel build warning(s): drivers/net/ethernet/huawei/hinic/hinic_hw_eqs.c:115: warning: Excess function parameter 'hw_handler' description in 'hinic_aeq_register_hw_cb' Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10net: hns: Fix a kernel-doc warning in hinic_hw_api_cmd.cWang Hai1-1/+1
Fixes the following W=1 kernel build warning(s): drivers/net/ethernet/huawei/hinic/hinic_hw_api_cmd.c:382: warning: Excess function parameter 'size' description in 'api_cmd' Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10net: hns: Fix some kernel-doc warnings in hns_enet.cWang Hai1-2/+1
Fixes the following W=1 kernel build warning(s): drivers/net/ethernet/hisilicon/hns/hns_enet.c:1841: warning: Excess function parameter 'netdev' description in 'hns_set_multicast_list' drivers/net/ethernet/hisilicon/hns/hns_enet.c:1841: warning: Excess function parameter 'p' description in 'hns_set_multicast_list' Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10net: hns: Fix some kernel-doc warnings in hns_dsaf_xgmac.cWang Hai1-2/+1
Fixes the following W=1 kernel build warning(s): drivers/net/ethernet/hisilicon/hns/hns_dsaf_xgmac.c:137: warning: Excess function parameter 'drv' description in 'hns_xgmac_enable' drivers/net/ethernet/hisilicon/hns/hns_dsaf_xgmac.c:497: warning: Excess function parameter 'cmd' description in 'hns_xgmac_get_regs' Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10net: hns: fix 'cdev' kernel-doc warning in hnae_ae_unregister()Wang Hai1-1/+1
Rename cdev to hdev. Fixes the following W=1 kernel build warning(s): drivers/net/ethernet/hisilicon/hns/hnae.c:444: warning: Excess function parameter 'cdev' description in 'hnae_ae_unregister' Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10hinic: Fix some kernel-doc warnings in hinic_hw_io.cWang Hai1-2/+2
Fixes the following W=1 kernel build warning(s): drivers/net/ethernet/huawei/hinic/hinic_hw_io.c:373: warning: Excess function parameter 'sq_msix_entry' description in 'hinic_io_create_qps' drivers/net/ethernet/huawei/hinic/hinic_hw_io.c:373: warning: Excess function parameter 'rq_msix_entry' description in 'hinic_io_create_qps' Rename these wrong names. Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10net: mvpp2: ptp: Fix unused variablesAlex Dewar1-4/+2
In the functions mvpp2_isr_handle_xlg() and mvpp2_isr_handle_gmac_internal(), the bool variable link is assigned a true value in the case that a given bit of val is set. However, if the bit is unset, no value is assigned to link and it is then passed to mvpp2_isr_handle_link() without being initialised. Fix by assigning to link the value of the bit test. Build-tested on x86. Fixes: 36cfd3a6e52b ("net: mvpp2: restructure "link status" interrupt handling") Signed-off-by: Alex Dewar <alex.dewar90@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10net: cxgb3: Fix some kernel-doc warningsWang Hai1-2/+2
Fixes the following W=1 kernel build warning(s): drivers/net/ethernet/chelsio/cxgb3/t3_hw.c:2209: warning: Excess function parameter 'adapter' description in 'clear_sge_ctxt' drivers/net/ethernet/chelsio/cxgb3/t3_hw.c:2975: warning: Excess function parameter 'adapter' description in 't3_set_proto_sram' Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-10net: ena: xdp: add queue counters for xdp actionsSameeh Jubran3-3/+28
When using XDP every ingress packet is passed to an eBPF (xdp) program which returns an action for this packet. This patch adds counters for the number of times each such action was received. It also counts all the invalid actions received from the eBPF program. Signed-off-by: Shay Agroskin <shayagr@amazon.com> Signed-off-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Copyright © 1996 – 2026 Jason A. Donenfeld. All Rights Reverse Engineered.