| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The driver version string is obviously not meant to be changed at run
time, so mark it `const'.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the temporary data buffer used when tapping into the SMT Tx queue
from the outer function level into the conditional block it's actually
used in and its containing skb is also declared, making the structure of
code better.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SPDX annotation for this driver does not match the license text,
which specifies GNU GPL 2 or later. Make the two match by correcting
the SPDX tag.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DEC FDDIcontroller 700 (DEFZA) uses a Tx/Rx queue pair to communicate
SMT frames with adapter's firmware. Any SMT frame received from the RMC
via the Rx queue is queued back by the driver to the SMT Rx queue for
the firmware to process. Similarly the firmware uses the SMT Tx queue
to supply the driver with SMT frames which are queued back to the Tx
queue for the RMC to send to the ring.
When a network tap is attached to an FDDI interface handled by `defza'
any incoming SMT frames captured are queued to our usual processing of
network data received, which in turn delivers them to any listening
taps.
However the outgoing SMT frames produced by the firmware bypass our
network protocol stack and are therefore not delivered to taps. This in
turn means that taps are missing a part of network traffic sent by the
adapter, which may make it more difficult to track down network problems
or do general traffic analysis.
Call `dev_queue_xmit_nit' then in the SMT Tx path, having checked that
a network tap is attached, with a newly-created `dev_nit_active' helper
wrapping the usual condition used in the transmit path.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the DEC FDDIcontroller 700 (DEFZA), Digital Equipment
Corporation's first-generation FDDI network interface adapter, made for
TURBOchannel and based on a discrete version of what eventually became
Motorola's widely used CAMEL chipset.
The CAMEL chipset is present for example in the DEC FDDIcontroller
TURBOchannel, EISA and PCI adapters (DEFTA/DEFEA/DEFPA) that we support
with the `defxx' driver, however the host bus interface logic and the
firmware API are different in the DEFZA and hence a separate driver is
required.
There isn't much to say about the driver except that it works, but there
is one peculiarity to mention. The adapter implements two Tx/Rx queue
pairs.
Of these one pair is the usual network Tx/Rx queue pair, in this case
used by the adapter to exchange frames with the ring, via the RMC (Ring
Memory Controller) chip. The Tx queue is handled directly by the RMC
chip and resides in onboard packet memory. The Rx queue is maintained
via DMA in host memory by adapter's firmware copying received data
stored by the RMC in onboard packet memory.
The other pair is used to communicate SMT frames with adapter's
firmware. Any SMT frame received from the RMC via the Rx queue must be
queued back by the driver to the SMT Rx queue for the firmware to
process. Similarly the firmware uses the SMT Tx queue to supply the
driver with SMT frames that must be queued back to the Tx queue for the
RMC to send to the ring.
This solution was chosen because the designers ran out of PCB space and
could not squeeze in more logic onto the board that would be required to
handle this SMT frame traffic without the need to involve the driver, as
with the later DEFTA/DEFEA/DEFPA adapters.
Finally the driver does some Frame Control byte decoding, so to avoid
magic numbers some macros are added to <linux/if_fddi.h>.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Maciej W. Rozycki