| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The KSZ8795 PHY ID is in fact used by KSZ8794/KSZ8795/KSZ8765 switches.
Update the PHY ID and name to reflect that, as this family of switches
is commonly refered to as KSZ87xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The KSZ8051 PHY and the KSZ8794/KSZ8795/KSZ8765 switch share exactly the
same PHY ID. Since KSZ8051 is higher in the ksphy_driver[] list of PHYs
in the micrel PHY driver, it is used even with the KSZ87xx switch. This
is wrong, since the KSZ8051 configures registers of the PHY which are
not present on the simplified KSZ87xx switch PHYs and misconfigures
other registers of the KSZ87xx switch PHYs.
Fortunatelly, it is possible to tell apart the KSZ8051 PHY from the
KSZ87xx switch by checking the Basic Status register Bit 0, which is
read-only and indicates presence of the Extended Capability Registers.
The KSZ8051 PHY has those registers while the KSZ87xx switch does not.
This patch implements simple check for the presence of this bit for
both the KSZ8051 PHY and KSZ87xx switch, to let both use the correct
PHY driver instance.
Fixes: 9d162ed69f51 ("net: phy: micrel: add support for KSZ8795")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Micrel KSZ9031 PHY may fail to establish a link when the Asymmetric
Pause capability is set. This issue is described in a Silicon Errata
(DS80000691D or DS80000692D), which advises to always disable the
capability.
Micrel KSZ9021 has no errata, but has the same issue with Asymmetric Pause.
This patch apply the same workaround as the one for KSZ9031.
Fixes: 3aed3e2a143c ("net: phy: micrel: add Asym Pause workaround")
Signed-off-by: Hans Andersson <hans.andersson@cellavision.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The KSZ8081 PHY has a factory test mode which is set at the de-assertion
of the reset line based on the RXER (KSZ8081RNA/RND) or TXC
(KSZ8081MNX/RNB) pin. If a pull-down is missing, or if the pin has a
pull-up, the factory test mode should be cleared by manually writing a 0
(according to the datasheet). This patch makes sure this factory test
bit is cleared in config_init().
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Micrel KSZ9031 PHY may fail to establish a link when the Asymmetric
Pause capability is set. This issue is described in a Silicon Errata
(DS80000691D or DS80000692D), which advises to always disable the
capability. This patch implements the workaround by defining a KSZ9031
specific get_feature callback to force the Asymmetric Pause capability
bit to be cleared.
This fixes issues where the link would not come up at boot time, or when
the Asym Pause bit was set later on.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recently genphy_read_abilities() has been added that dynamically detects
clause 22 PHY abilities. I *think* this detection should work with all
supported PHY's, at least for the ones with basic features sets, i.e.
PHY_BASIC_FEATURES and PHY_GBIT_FEATURES. So let's remove setting these
features explicitly and rely on phylib feature detection.
I don't have access to most of these PHY's, therefore I'd appreciate
regression testing.
v2:
- make the feature constant a comment so that readers know which
features are supported by the respective PHY
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
With Micrel KSZ8061 PHY, the link may occasionally not come up after
Ethernet cable connect. The vendor's (Microchip, former Micrel) errata
sheet 80000688A.pdf descripes the problem and possible workarounds in
detail, see below.
The batch implements workaround 1, which permanently fixes the issue.
DESCRIPTION
Link-up may not occur properly when the Ethernet cable is initially
connected. This issue occurs more commonly when the cable is connected
slowly, but it may occur any time a cable is connected. This issue occurs
in the auto-negotiation circuit, and will not occur if auto-negotiation
is disabled (which requires that the two link partners be set to the
same speed and duplex).
END USER IMPLICATIONS
When this issue occurs, link is not established. Subsequent cable
plug/unplaug cycle will not correct the issue.
WORk AROUND
There are four approaches to work around this issue:
1. This issue can be prevented by setting bit 15 in MMD device address 1,
register 2, prior to connecting the cable or prior to setting the
Restart Auto-negotiation bit in register 0h. The MMD registers are
accessed via the indirect access registers Dh and Eh, or via the Micrel
EthUtil utility as shown here:
. if using the EthUtil utility (usually with a Micrel KSZ8061
Evaluation Board), type the following commands:
> address 1
> mmd 1
> iw 2 b61a
. Alternatively, write the following registers to write to the
indirect MMD register:
Write register Dh, data 0001h
Write register Eh, data 0002h
Write register Dh, data 4001h
Write register Eh, data B61Ah
2. The issue can be avoided by disabling auto-negotiation in the KSZ8061,
either by the strapping option, or by clearing bit 12 in register 0h.
Care must be taken to ensure that the KSZ8061 and the link partner
will link with the same speed and duplex. Note that the KSZ8061
defaults to full-duplex when auto-negotiation is off, but other
devices may default to half-duplex in the event of failed
auto-negotiation.
3. The issue can be avoided by connecting the cable prior to powering-up
or resetting the KSZ8061, and leaving it plugged in thereafter.
4. If the above measures are not taken and the problem occurs, link can
be recovered by setting the Restart Auto-Negotiation bit in
register 0h, or by resetting or power cycling the device. Reset may
be either hardware reset or software reset (register 0h, bit 15).
PLAN
This errata will not be corrected in the future revision.
Fixes: 7ab59dc15e2f ("drivers/net/phy/micrel_phy: Add support for new PHYs")
Signed-off-by: Alexander Onnasch <alexander.onnasch@landisgyr.com>
Signed-off-by: Rajasingh Thavamani <T.Rajasingh@landisgyr.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Where the license text and the MODULE_LICENSE() value agree, convert
to using an SPDX header, removing the license text.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Completely minor snmp doc conflict.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver implements open-coded versions of phy_read_mmd() and
phy_write_mmd() for KSZ9031. That's not needed, let's use the
phylib functions directly.
This is compile-tested only because I have no such hardware.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bcm87xx and micrel driver has PHYs which are missing the .features
value. Add them. The bcm87xx is a 10G FEC only PHY. Add the needed
features definition of this PHY.
Fixes: 719655a14971 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Reported-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So far genphy_soft_reset was used automatically if the PHY driver
didn't implement the soft_reset callback. This changed with the
mentioned commit and broke KSZ9031. To fix this configure the
KSZ9031 PHY driver to use genphy_soft_reset.
Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that flag PHY_HAS_INTERRUPT has been replaced with a check for
callbacks config_intr and ack_interrupt, we can remove setting this
flag from all driver configs.
Last but not least remove flag PHY_HAS_INTERRUPT completely.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for Microchip Technology KSZ9131 10/100/1000 Ethernet PHY
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
S390 bpf_jit.S is removed in net-next and had changes in 'net',
since that code isn't used any more take the removal.
TLS data structures split the TX and RX components in 'net-next',
put the new struct members from the bug fix in 'net' into the RX
part.
The 'net-next' tree had some reworking of how the ERSPAN code works in
the GRE tunneling code, overlapping with a one-line headroom
calculation fix in 'net'.
Overlapping changes in __sock_map_ctx_update_elem(), keep the bits
that read the prog members via READ_ONCE() into local variables
before using them.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The micrel KSZ9031 phy has a optional clock pin (CLK125_NDO) which can be
used as reference clock for the MAC unit. The clock signal must meet the
RGMII requirements to ensure the correct data transmission between the
MAC and the PHY. The KSZ9031 phy does not fulfill the duty cycle
requirement if the phy is configured as slave. For a complete
describtion look at the errata sheets: DS80000691D or DS80000692D.
The errata sheet recommends to force the phy into master mode whenever
there is a 1000Base-T link-up as work around. Only set the
"micrel,force-master" property if you use the phy reference clock provided
by CLK125_NDO pin as MAC reference clock in your application.
Attenation, this workaround is only usable if the link partner can
be configured to slave mode for 1000Base-T.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
[m.felsch@pengutronix.de: fix dt-binding documentation]
[m.felsch@pengutronix.de: use already existing result var for read/write]
[m.felsch@pengutronix.de: add error handling]
[m.felsch@pengutronix.de: add more comments]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
U64_MAX is well defined now while the UINT64_MAX is not, so we fall
back to drivers' own definition as below:
#ifndef UINT64_MAX
#define UINT64_MAX (u64)(~((u64)0))
#endif
I believe this is in one phy driver then copied and pasted to other phy
drivers.
Replace the UINT64_MAX with U64_MAX to clean up the source code.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new general dummy stubs for MMD register access were introduced.
Use that for the codes reuse.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Our statistics strings are allocated at initialization without being
bound to a specific size, yet, we would copy ETH_GSTRING_LEN bytes using
memcpy() which would create out of bounds accesses, this was flagged by
KASAN. Replace this with strlcpy() to make sure we are bound the source
buffer size and we also always NUL-terminate strings.
Fixes: 2b2427d06426 ("phy: micrel: Add ethtool statistics counters")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net/ipv6/ip6_gre.c is a case of parallel adds.
include/trace/events/tcp.h is a little bit more tricky. The removal
of in-trace-macro ifdefs in 'net' paralleled with moving
show_tcp_state_name and friends over to include/trace/events/sock.h
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under some circumstances driver will perform PHY reset in
ksz9031_read_status() to fix autoneg failure case (idle error count =
0xFF). When this happens ksz9031 will not detect link status change any
more when connecting to Netgear 1G switch (link can be recovered sometimes by
restarting netdevice "ifconfig down up"). Reproduced with TI am572x board
equipped with ksz9031 PHY while connecting to Netgear 1G switch.
Fix the issue by reconfiguring autonegotiation after PHY reset in
ksz9031_read_status().
Fixes: d2fd719bcb0e ("net/phy: micrel: Add workaround for bad autoneg")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Small overlapping change conflict ('net' changed a line,
'net-next' added a line right afterwards) in flexcan.c
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove generic settings for callbacks config_aneg and read_status
from drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix obvious typo that first return value is set but not checked.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A set of overlapping changes in macvlan and the rocker
driver, nothing serious.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit ("net/phy: micrel: Add workaround for bad autoneg") fixes an
autoneg failure case by resetting the hardware. This turns off
intterupts. Things will work themselves out if the phy polls, as it will
figure out it's state during a poll. However if the phy uses only
intterupts, the phy will stall, since interrupts are off. This patch
fixes the issue by calling config_intr after resetting the phy.
Fixes: d2fd719bcb0e ("net/phy: micrel: Add workaround for bad autoneg ")
Signed-off-by: Zach Brown <zach.brown@ni.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just some simple overlapping changes in marvell PHY driver
and the DSA core code.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These bits seem to be lost after a suspend/resume cycle so just set them
again. Do this by splitting the handling of these bits into a function
that is also called on resume.
This patch fixes ethernet suspend/resume on imx6ul-14x14-evk boards.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding Microchip 9477 Phy included in KSZ9477 Switch.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit fa8cddaf903c ("net phylib: Remove unnecessary condition check in phy")
removed the only place where the PHY flag PHY_HAS_MAGICANEG was
checked. But it left the flag being set in the drivers. Remove the flag.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 99f81afc139c6edd14d77a91ee91685a414a1c66.
It was papering over the real problem, which is fixed by commit
f555f34fdc58 ("net: phy: fix auto-negotiation stall due to unavailable
interrupt")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A function in kernel/bpf/syscall.c which got a bug fix in 'net'
was moved to kernel/bpf/verifier.c in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now the command:
ethtool --phy-statistics eth0
will cause system crash with meassage "Unable to handle kernel NULL pointer
dereference at virtual address 00000010" from:
(kszphy_get_stats) from [<c069f1d8>] (ethtool_get_phy_stats+0xd8/0x210)
(ethtool_get_phy_stats) from [<c06a0738>] (dev_ethtool+0x5b8/0x228c)
(dev_ethtool) from [<c06b5484>] (dev_ioctl+0x3fc/0x964)
(dev_ioctl) from [<c0679f7c>] (sock_ioctl+0x170/0x2c0)
(sock_ioctl) from [<c02419d4>] (do_vfs_ioctl+0xa8/0x95c)
(do_vfs_ioctl) from [<c02422c4>] (SyS_ioctl+0x3c/0x64)
(SyS_ioctl) from [<c0107d60>] (ret_fast_syscall+0x0/0x44)
The reason: phy_driver structure for KSZ9031 phy has no .probe() callback
defined. As result, struct phy_device *phydev->priv pointer will not be
initializes (null).
This issue will affect also following phys:
KSZ8795, KSZ886X, KSZ8873MLL, KSZ9031, KSZ9021, KSZ8061, KS8737
Fix it by:
- adding .probe() = kszphy_probe() callback to KSZ9031, KSZ9021
phys. The kszphy_probe() can be re-used as it doesn't do any phy specific
settings.
- removing statistic callbacks from other phys (KSZ8795, KSZ886X,
KSZ8873MLL, KSZ8061, KS8737) as they doesn't have corresponding
statistic counters.
Fixes: 2b2427d06426 ("phy: micrel: Add ethtool statistics counters")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert micrel to the new read_mmd/write_mmd driver methods. This
Clause 22 PHY does not support any MMD access method.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As pr commit "net: phy: phy drivers should not set SUPPORTED_[Asym_]Pause"
this phy driver should not set these feature bits.
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Fixes: 9d162ed69f51 ("net: phy: micrel: add support for KSZ8795")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is adds support for the PHYs in the KSZ8795 5port managed switch.
It will allow to detect the link between the switch and the soc
and uses the same read_status functions as the KSZ8873MLL switch.
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of having individual PHY drivers set the SUPPORTED_Pause and
SUPPORTED_Asym_Pause flags, phylib itself should set those flags,
unless there is a hardware erratum or other special case. During
autonegotiation, the PHYs will determine whether to enable pause
frame support.
Pause frames are a feature that is supported by the MAC. It is the MAC
that generates the frames and that processes them. The PHY can only be
configured to allow them to pass through.
This commit also effectively reverts the recently applied c7a61319
("net: phy: dp83848: Support ethernet pause frames").
So the new process is:
1) Unless the PHY driver overrides it, phylib sets the SUPPORTED_Pause
and SUPPORTED_AsymPause bits in phydev->supported. This indicates that
the PHY supports pause frames.
2) The MAC driver checks phydev->supported before it calls phy_start().
If (SUPPORTED_Pause | SUPPORTED_AsymPause) is set, then the MAC driver
sets those bits in phydev->advertising, if it wants to enable pause
frame support.
3) When the link state changes, the MAC driver checks phydev->pause and
phydev->asym_pause, If the bits are set, then it enables the corresponding
features in the MAC. The algorithm is:
if (phydev->pause)
The MAC should be programmed to receive and honor
pause frames it receives, i.e. enable receive flow control.
if (phydev->pause != phydev->asym_pause)
The MAC should be programmed to transmit pause
frames when needed, i.e. enable transmit flow control.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix setting of SUPPORTED_FIBRE bit as it was not present in features
of KSZ8041.
Signed-off-by: Kirill Esipov <yesipov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set bit 0 in register 1C.23 to enable the EDPD feature of the
KSZ9031 PHY. This reduces power consumption when the link is
down.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Like the ksz8081, the ksz9031 has the behavior where it will clear the
interrupt enable bits when leaving power down. This takes advantage of the
solution provided by f5aba91.
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Disable all interrupts when suspend, they will be enabled
when resume. Otherwise, the suspend/resume process will be
blocked occasionally.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are KSZ8721 PHYs with phy_id 0x00221619. In order to detect them
as PHY_ID_KSZ8001 compatible while staying different to PHY_ID_KSZ9021
ignore the last two bits when matching PHY_ID
Signed-off-by: Alexander Stein <alexanders83@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can't detect the FXEN (fiber mode) bootstrap pin, so configure
it via a boolean device tree property "micrel,fiber-mode".
If it is enabled, auto-negotiation is not supported.
The only available modes are 100base-fx (full duplex and half duplex).
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the hardcoded mask 0x00fffff0 with MICREL_PHY_ID_MASK for
better readability.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Disable auto negotiation on init to properly detect an already plugged
cable at boot.
At boot, when the phy is started, it is in the PHY_UP state.
However, if a cable is plugged at boot, because auto negociation is already
enabled at the time we get the first interrupt, the phy is already running.
But the state machine then switches from PHY_UP to PHY_AN and calls
phy_start_aneg(). phy_start_aneg() will not do anything because aneg is
already enabled on the phy. It will then wait for a interrupt before going
further. This interrupt will never happen unless the cable is unplugged and
then replugged.
It was working properly before 321beec5047a (net: phy: Use interrupts when
available in NOLINK state) because switching to NOLINK meant starting
polling the phy, even if IRQ were enabled.
Fixes: 321beec5047a (net: phy: Use interrupts when available in NOLINK state)
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At least on ksz8081, when getting back from power down, interrupts are
disabled. ensure they are reenabled if they were previously enabled.
This fixes resuming which is failing on the xplained boards from atmel
since 321beec5047a (net: phy: Use interrupts when available in NOLINK
state)
Fixes: 321beec5047a (net: phy: Use interrupts when available in NOLINK state)
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Marek Vasut
Hans Andersson
Antoine Tenart
Heiner Kallweit
David S. Miller
Rajasingh Thavamani
Andrew Lunn
Yuiko Oshino
Markus Niebel
Jisheng Zhang
Kevin Hao
Florian Fainelli
Grygorii Strashko
Max Uvarov
Zach Brown
Leonard Crestez
Woojung Huh
Russell King
Sean Nyekjaer
Timur Tabi
Kirill Esipov
Mike Looijmans
Xander Huff
Wenyou Yang
Alexander Stein
Philipp Zabel
Fabio Estevam
Alexandre Belloni