| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The LAN8740, like the 8720, also requires a reset after enabling clock.
The datasheet [1] 3.8.5.1 says:
"During a Hardware reset, an external clock must be supplied
to the XTAL1/CLKIN signal."
I have observed this issue on a custom i.MX6 based board with
the LAN8740A.
[1] http://ww1.microchip.com/downloads/en/DeviceDoc/8740a.pdf
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recently genphy_read_abilities() has been added that dynamically detects
clause 22 PHY abilities. I *think* this detection should work with all
supported PHY's, at least for the ones with basic features sets, i.e.
PHY_BASIC_FEATURES and PHY_GBIT_FEATURES. So let's remove setting these
features explicitly and rely on phylib feature detection.
I don't have access to most of these PHY's, therefore I'd appreciate
regression testing.
v2:
- make the feature constant a comment so that readers know which
features are supported by the respective PHY
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Where the license text and the MODULE_LICENSE() value agree, convert
to using an SPDX header, removing the license text.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that flag PHY_HAS_INTERRUPT has been replaced with a check for
callbacks config_intr and ack_interrupt, we can remove setting this
flag from all driver configs.
Last but not least remove flag PHY_HAS_INTERRUPT completely.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
U64_MAX is well defined now while the UINT64_MAX is not, so we fall
back to drivers' own definition as below:
#ifndef UINT64_MAX
#define UINT64_MAX (u64)(~((u64)0))
#endif
I believe this is in one phy driver then copied and pasted to other phy
drivers.
Replace the UINT64_MAX with U64_MAX to clean up the source code.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Microchip/SMSC LAN8710/LAN8720 PHYs need (according to their
datasheet [1]) a continuous REF_CLK when configured to "REF_CLK In Mode".
Therefore set the PHY_RST_AFTER_CLK_EN flag for those PHYs to let the
ETH driver reset them after the REF_CLK is enabled.
[1] http://ww1.microchip.com/downloads/en/DeviceDoc/00002165B.pdf
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove generic settings for callbacks config_aneg and read_status
from drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The memcpy annotation triggers for a fixed-length buffer copy:
In file included from /git/arm-soc/arch/arm64/include/asm/processor.h:30:0,
from /git/arm-soc/arch/arm64/include/asm/spinlock.h:21,
from /git/arm-soc/include/linux/spinlock.h:87,
from /git/arm-soc/include/linux/seqlock.h:35,
from /git/arm-soc/include/linux/time.h:5,
from /git/arm-soc/include/linux/stat.h:21,
from /git/arm-soc/include/linux/module.h:10,
from /git/arm-soc/drivers/net/phy/smsc.c:20:
In function 'memcpy',
inlined from 'smsc_get_strings' at /git/arm-soc/drivers/net/phy/smsc.c:166:3:
/git/arm-soc/include/linux/string.h:309:4: error: call to '__read_overflow2' declared with attribute error: detected read beyond size of object passed as 2nd parameter
Using strncpy instead of memcpy should do the right thing here.
Fixes: 030a89028db0 ("net: phy: smsc: Implement PHY statistics")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of the PHYs supported by the SMSC driver have a counter of symbol
errors. This is 16 bit wide and wraps around when it reaches its
maximum value.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-By: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit fa8cddaf903c ("net phylib: Remove unnecessary condition check in phy")
removed the only place where the PHY flag PHY_HAS_MAGICANEG was
checked. But it left the flag being set in the drivers. Remove the flag.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is an include loop between netdevice.h, dsa.h, devlink.h because
of NETDEV_ALIGN, making it impossible to use devlink structures in
dsa.h.
Break this loop by taking dsa.h out of netdevice.h, add a forward
declaration of dsa_switch_tree and netdev_set_default_ethtool_ops()
function, which is what netdevice.h requires.
No longer having dsa.h in netdevice.h means the includes in dsa.h no
longer get included. This breaks a few other files which depend on
these includes. Add these directly in the affected file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of having individual PHY drivers set the SUPPORTED_Pause and
SUPPORTED_Asym_Pause flags, phylib itself should set those flags,
unless there is a hardware erratum or other special case. During
autonegotiation, the PHYs will determine whether to enable pause
frame support.
Pause frames are a feature that is supported by the MAC. It is the MAC
that generates the frames and that processes them. The PHY can only be
configured to allow them to pass through.
This commit also effectively reverts the recently applied c7a61319
("net: phy: dp83848: Support ethernet pause frames").
So the new process is:
1) Unless the PHY driver overrides it, phylib sets the SUPPORTED_Pause
and SUPPORTED_AsymPause bits in phydev->supported. This indicates that
the PHY supports pause frames.
2) The MAC driver checks phydev->supported before it calls phy_start().
If (SUPPORTED_Pause | SUPPORTED_AsymPause) is set, then the MAC driver
sets those bits in phydev->advertising, if it wants to enable pause
frame support.
3) When the link state changes, the MAC driver checks phydev->pause and
phydev->asym_pause, If the bits are set, then it enables the corresponding
features in the MAC. The algorithm is:
if (phydev->pause)
The MAC should be programmed to receive and honor
pause frames it receives, i.e. enable receive flow control.
if (phydev->pause != phydev->asym_pause)
The MAC should be programmed to transmit pause
frames when needed, i.e. enable transmit flow control.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We detected some problems using the smsc lan8720a in combination with
i.MX28 and tracked this down to commit 21009686662f ("net: phy: smsc: move
smsc_phy_config_init reset part in a soft_reset function")
With 2100968666 the generic soft reset is replaced by a specific function
which handles power down state correctly. But additionally the soft reset
itself got conditional and is therefore also only performed if the phy is
in power down state.
This patch keeps the conditional wake up from power down, but
re-introduces the unconditional soft reset using the generic soft reset
function.
It was tested on linux-4.1.25 and linux-4.7.0-rc2.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@ginzinger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the lan87xx_read_status function is getting called the
energy detect mode is enabled again even if it has been
disabled by device tree.
Added private struct to check the energy detect status.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
LAN8740 has a different phy_id than LAN8710/LAN8720.
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rather than have each driver set the driver owner field, do it once in
the core code. This will also help with later changes, when the device
structure will move.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some boards the energy enable detect mode leads in
trouble with some switches, so make the enabling of
this mode configurable through DT.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/phy/smsc.c:127:3-4: Unneeded semicolon
Remove unneeded semicolon.
Generated by: scripts/coccinelle/misc/semicolon.cocci
CC: Igor Plyatov <plyatov@gmail.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* Due to HW bug, LAN8700 sometimes does not detect presence of energy in the
Ethernet cable in Energy Detect Power-Down mode (e.g while EDPWRDOWN bit is
set, the ENERGYON bit does not asserted sometimes). This is a common bug of
LAN87xx family of PHY chips.
* The lan87xx_read_status() was improved to acquire ENERGYON bit. Its previous
algorythm still not reliable on 100 % and sometimes skip cable plugging.
Signed-off-by: Igor Plyatov <plyatov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace module init/exit which only calls phy_drivers_register with
module_phy_driver macro.
Tested using Micrel driver, and otherwise compile-tested only.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On the one hand, phy_device.c provides a generic reset function if the phy
driver does not provide a soft_reset pointer. This generic reset does not take
into account the state of the phy, with a potential failure if the phy is in
powerdown mode. On the other hand, smsc driver provides a function with both
correct reset behaviour and configuration.
This patch moves the reset part into a new smsc_phy_reset function and provides
the soft_reset pointer to have a correct reset behaviour by default.
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This was caught when using a spatch (aka. coccinelle) script
written by Joe Perches.
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Correct a mistake made in the previous commit due to reckless
copy-and-pasting.
Signed-off-by: Patrick Trantham <patrick.trantham@fuel7.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A SMSC PHY in power down mode can't be used.
If a SMSC PHY is in this mode in the config_init
stage, the mode "all capable" is set. So the PHY
could then be used.
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch re-enables Energy Detect Power Down (EDPD) mode for the
LAN8710/LAN8720. EDPD mode was disabled in a previous commit,
(b629820d18fa65cc598390e4b9712fd5f83ee693), because it was causing the
PHY to not be able to detect a link when cold started without a cable
connected.
The LAN8710/LAN8720 requires a minimum of 2 link pulses within 64ms of
each other in order to set the ENERGYON bit and exit EDPD mode. If a
link partner does send the pulses within this interval, the PHY will
remained powered down.
This workaround will manually toggle the PHY on/off upon calls to
read_status in order to generate link test pulses if the link is down.
If a link partner is present, it will respond to the pulses, which will
cause the ENERGYON bit to be set and will cause the EDPD mode to be
exited.
Signed-off-by: Patrick Trantham <patrick.trantham@fuel7.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The LAN8710/LAN8720 chips do have broken the "FlexPWR" smart power-saving
capability. Enabling it leads to the PHY not being able to detect Link when
cold-started without cable connected. Thus, make sure this is disabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christian Hohnstaedt <chohnstaedt@innominate.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull trivial tree from Jiri Kosina:
"Trivial updates all over the place as usual."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (29 commits)
Fix typo in include/linux/clk.h .
pci: hotplug: Fix typo in pci
iommu: Fix typo in iommu
video: Fix typo in drivers/video
Documentation: Add newline at end-of-file to files lacking one
arm,unicore32: Remove obsolete "select MISC_DEVICES"
module.c: spelling s/postition/position/g
cpufreq: Fix typo in cpufreq driver
trivial: typo in comment in mksysmap
mach-omap2: Fix typo in debug message and comment
scsi: aha152x: Fix sparse warning and make printing pointer address more portable.
Change email address for Steve Glendinning
Btrfs: fix typo in convert_extent_bit
via: Remove bogus if check
netprio_cgroup.c: fix comment typo
backlight: fix memory leak on obscure error path
Documentation: asus-laptop.txt references an obsolete Kconfig item
Documentation: ManagementStyle: fixed typo
mm/vmscan: cleanup comment error in balance_pgdat
mm: cleanup on the comments of zone_reclaim_stat
...
|
|
I no longer have a mailbox at smsc.com, and I've had two reports
that that email address now bounces from people trying to
contact me. This patch updates all references to that invalid
address to one that I can be contacted on more permanently.
This patch also updates the maintainer status to reflect
the fact I'm no longer directly paid to maintain these drivers.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
If registering of one of them fails, all already registered drivers
of this module will be unregistered.
Use the new register/unregister functions in all drivers
registering more than one driver.
amd.c, realtek.c: Simplify: directly return registration result.
Tested with broadcom.c
All others compile-tested.
Signed-off-by: Christian Hohnstaedt <chohnstaedt@innominate.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SMSC generation 4 LAN chips integrate an IEEE 802.3 ethernet physical layer.
The ethernet driver for this family of devices needs to access the SMSC PHY
registers and bit-fields.
So, this patch moves these constants to a place where it can be used for both
the PHY and LAN drivers.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MODULE_DEVICE_TABLE only expands to something if it's compiled
for a module. So when building-in support for the phys, the
mdio_device_id tables are unused. Marking them with __maybe_unused
fixes the following warnings:
drivers/net/phy/bcm63xx.c:134: warning: 'bcm63xx_tbl' defined but not used
drivers/net/phy/broadcom.c:933: warning: 'broadcom_tbl' defined but not used
drivers/net/phy/cicada.c:162: warning: 'cicada_tbl' defined but not used
drivers/net/phy/davicom.c:222: warning: 'davicom_tbl' defined but not used
drivers/net/phy/et1011c.c:114: warning: 'et1011c_tbl' defined but not used
drivers/net/phy/icplus.c:137: warning: 'icplus_tbl' defined but not used
drivers/net/phy/lxt.c:226: warning: 'lxt_tbl' defined but not used
drivers/net/phy/marvell.c:724: warning: 'marvell_tbl' defined but not used
drivers/net/phy/micrel.c:234: warning: 'micrel_tbl' defined but not used
drivers/net/phy/national.c:154: warning: 'ns_tbl' defined but not used
drivers/net/phy/qsemi.c:141: warning: 'qs6612_tbl' defined but not used
drivers/net/phy/realtek.c:82: warning: 'realtek_tbl' defined but not used
drivers/net/phy/smsc.c:257: warning: 'smsc_tbl' defined but not used
drivers/net/phy/ste10Xp.c:135: warning: 'ste10Xp_tbl' defined but not used
drivers/net/phy/vitesse.c:195: warning: 'vitesse_tbl' defined but not used
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SMSC Ethernet Transceivers (LAN88710, LAN8710, LAN8720, LAN8187,
LAN8700, LAN83C185) provide a mechanism to conserve power when
the device is not connected to an active link partner
(Energy Detect Mode).
So this patch enables the Energy Detect power-down mode
for these Transceivers.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
LAN8710 and LAN8720 are two new 10/100 ethernet PHY models. The two
share the same phy id, this patch adds it to the smsc phy driver.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All supported SMSC PHYs implement the standard "power down" bit 11 of
BMCR, so this patch adds support using the generic genphy_{suspend,resume}
functions.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Attached is a driver for SMSC's LAN911x and LAN921x families of embedded
ethernet controllers.
There is an existing smc911x driver in the tree; this is intended to
replace it. Dustin McIntire (the author of the smc911x driver) has
expressed his support for switching to this driver.
This driver contains workarounds for all known hardware issues, and has
been tested on all flavours of the chip on multiple architectures.
This driver now uses phylib, so this patch also adds support for the
device's internal phy
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Bahadir Balban <Bahadir.Balban@arm.com>
Signed-off-by: Dustin Mcintire <dustin@sensoria.com>
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Add support for two additional SMSC PHY models with identical interrupt
source and mask registers to the LAN83C185
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Several models of SMSC PHY have the same interrupt status and mask
registers as the LAN83C185, so these functions can service multiple
different PHY drivers.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
config.h is automatically included by kbuild these days.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
new SMSC LAN83C185 10BaseT/100BaseTX PHY driver for the PHY subsystem
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
Martin Fuzzey
Heiner Kallweit
Andrew Lunn
Jisheng Zhang
Richard Leitner
Arnd Bergmann
Timur Tabi
Manfred Schlaegl
Teresa Remmet
Joshua Henderson
Heiko Schocher
kbuild test robot
Igor Plyatov
Johan Hovold
Gwenhael Goavec-Merou
Shruti Kanetkar
Patrick Trantham
trem
Marek Vasut
Linus Torvalds
Steve Glendinning
Christian Hohnstaedt
Javier Martinez Canillas
Uwe Kleine-König
David Woodhouse
Giuseppe Cavallaro
Steve Glendinning
Dave Jones
Herbert Valerio Riedel