| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Move the Freescale drivers into drivers/net/ethernet/freescale/ and
make the necessary Kconfig and Makefile changes.
CC: Sandeep Gopalpet <sandeep.kumar@freescale.com>
CC: Andy Fleming <afleming@freescale.com>
CC: Shlomi Gridish <gridish@freescale.com>
CC: Li Yang <leoli@freescale.com>
CC: Pantelis Antoniou <pantelis.antoniou@gmail.com>
CC: Vitaly Bordug <vbordug@ru.mvista.com>
CC: Dan Malek <dmalek@jlc.net>
CC: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
|
In commit 58933c64(ucc_geth: Fix the wrong the Rx/Tx FIFO size),
the UCC_GETH_UTFTT_INIT is set to 512 based on the recommendation
of the QE Reference Manual. But that will sometimes cause tx halt
while working in half duplex mode.
According to errata draft QE_GENERAL-A003(High Tx Virtual FIFO
threshold size can cause UCC to halt), setting UTFTT less than
[(UTFS x (M - 8)/M) - 128] will prevent this from happening
(M is the minimum buffer size).
The patch changes UTFTT back to 256.
Signed-off-by: Li Yang <leoli@freescale.com>
Cc: Jean-Denis Boyer <jdboyer@media5corp.com>
Cc: Andreas Schmitz <Andreas.Schmitz@riedel.net>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cleanup patch.
Use new __packed annotation in drivers/net/
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
current the Rx/Tx FIFO size settings cause problem
when four UEC ethernets work simultaneously.
eg: GETH1, UEM-J15, GETH2, UEC-J5 on 8569MDS board
$ ifconfig eth0 10.193.20.166
$ ifconfig eth1 10.193.20.167
$ ifconfig eth2 10.193.20.168
then
$ ifconfig eth3 10.193.20.169
The fourth ethernet will cause all of interface broken,
you cann't ping successfully any more.
The patch fix this issue for MPC8569 Rev1.0 and Rev2.0
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
That is "success", "unknown", "through", "performance", "[re|un]mapping"
, "access", "default", "reasonable", "[con]currently", "temperature"
, "channel", "[un]used", "application", "example","hierarchy", "therefore"
, "[over|under]flow", "contiguous", "threshold", "enough" and others.
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch implements suspend/resume and WOL support for UCC Ethernet
driver.
We support two wake up events: wake on PHY/link changes and wake
on magic packet.
In some CPUs (like MPC8569) QE shuts down during sleep, so magic packet
detection is unusable, and also on resume we should fully reinitialize
UCC structures.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can reclaim transmitted skbs to use in the receive path, so-called
skb recycling support.
Also reorder ucc_geth_poll() steps, so that we'll clean tx ring firstly,
thus maybe reclaim some skbs for rx.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (55 commits)
netxen: fix tx ring accounting
netxen: fix detection of cut-thru firmware mode
forcedeth: fix dma api mismatches
atm: sk_wmem_alloc initial value is one
net: correct off-by-one write allocations reports
via-velocity : fix no link detection on boot
Net / e100: Fix suspend of devices that cannot be power managed
TI DaVinci EMAC : Fix rmmod error
net: group address list and its count
ipv4: Fix fib_trie rebalancing, part 2
pkt_sched: Update drops stats in act_police
sky2: version 1.23
sky2: add GRO support
sky2: skb recycling
sky2: reduce default transmit ring
sky2: receive counter update
sky2: fix shutdown synchronization
sky2: PCI irq issues
sky2: more receive shutdown
sky2: turn off pause during shutdown
...
Manually fix trivial conflict in net/core/skbuff.c due to kmemcheck
|
|
-- derived from reverted commit 047584ce94108012288554a5f84585d792cc7f8f
-- reworked by Grant Likely to play nice with commit:
"net: Rework ucc_geth driver to use of_mdio infrastructure"
(0b9da337dca972e7a4144e298ec3adb8f244d4a4)
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 047584ce94108012288554a5f84585d792cc7f8f.
This patch meshes badly with "net: Rework ucc_geth driver to use
of_mdio infrastructure" (0b9da337dca972e7a4144e298ec3adb8f244d4a4).
Since most of the patch needs to be reworked, it is clearer to revert
the patch and then apply the corrected version
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1244 commits)
pkt_sched: Rename PSCHED_US2NS and PSCHED_NS2US
ipv4: Fix fib_trie rebalancing
Bluetooth: Fix issue with uninitialized nsh.type in DTL-1 driver
Bluetooth: Fix Kconfig issue with RFKILL integration
PIM-SM: namespace changes
ipv4: update ARPD help text
net: use a deferred timer in rt_check_expire
ieee802154: fix kconfig bool/tristate muckup
bonding: initialization rework
bonding: use is_zero_ether_addr
bonding: network device names are case sensative
bonding: elminate bad refcount code
bonding: fix style issues
bonding: fix destructor
bonding: remove bonding read/write semaphore
bonding: initialize before registration
bonding: bond_create always called with default parameters
x_tables: Convert printk to pr_err
netfilter: conntrack: optional reliable conntrack event delivery
list_nulls: add hlist_nulls_add_head and hlist_nulls_del
...
|
|
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the definition of riscTx and riscRx to unsigned integer instead of
enum, and change their values to support 4 risc allocation if the qe has
4 RISC engines.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This patch simplifies the driver by making use of more common code.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This will make the system alot more responsive while ping flooding the
ucc_geth ethernet interface.
Also set NAPI weight to 64 as this is a common value.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver should pass a device that actually specifies internal DMA
ops, but currently it passes netdev's device, which is wrong and that
causes following oops:
Kernel BUG at c01c4df8 [verbose debug info unavailable]
Oops: Exception in kernel mode, sig: 5 [#1]
[...]
NIP [c01c4df8] get_new_skb+0x7c/0xf8
LR [c01c4da4] get_new_skb+0x28/0xf8
Call Trace:
[ef82be00] [c01c4da4] get_new_skb+0x28/0xf8 (unreliable)
[ef82be20] [c01c4eb8] rx_bd_buffer_set+0x44/0x98
[ef82be40] [c01c62bc] ucc_geth_startup+0x11b0/0x147c
[ef82be80] [c01c6674] ucc_geth_open+0xec/0x2a4
[ef82bea0] [c02288a4] dev_open+0xc0/0x11c
[...]
Fix this by passing of_device's device that specifies DMA ops in its
archdata.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that the driver is exclusively an of_platform driver we no longer
use the structs and #defines in fsl_devices.h
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ucc_geth.c
|
|
commit b1c4a9dddf09fe99b8f88252718ac5b357363dc4 ("ucc_geth: Change
uec phy id to the same format as gianfar's") introduced a regression
in the ucc_geth driver that causes this oops when fixed-link is used:
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc0151270
Oops: Kernel access of bad area, sig: 11 [#1]
TMCUTU
NIP: c0151270 LR: c0151270 CTR: c0017760
REGS: cf81fa60 TRAP: 0300 Not tainted (2.6.29-rc8)
MSR: 00009032 <EE,ME,IR,DR> CR: 24024042 XER: 20000000
DAR: 00000000, DSISR: 20000000
TASK = cf81cba0[1] 'swapper' THREAD: cf81e000
GPR00: c0151270 cf81fb10 cf81cba0 00000000 c0272e20 c025f354 00001e80
cf86b08c
GPR08: d1068200 cffffb74 06000000 d106c200 42024042 10085148 0fffd000
0ffc81a0
GPR16: 00000001 00000001 00000000 007ffeb0 00000000 0000c000 cf83f36c
cf83f000
GPR24: 00000030 cf83f360 cf81fb20 00000000 d106c200 20000000 00001e80
cf83f360
NIP [c0151270] ucc_geth_open+0x330/0x1efc
LR [c0151270] ucc_geth_open+0x330/0x1efc
Call Trace:
[cf81fb10] [c0151270] ucc_geth_open+0x330/0x1efc (unreliable)
[cf81fba0] [c0187638] dev_open+0xbc/0x12c
[cf81fbc0] [c0187e38] dev_change_flags+0x8c/0x1b0
This patch fixes the issue by removing offending (and somewhat
duplicate) code from init_phy() routine, and changes _probe()
function to use uec_mdio_bus_name().
Also, since we fully construct phy_bus_id in the _probe() routine,
we no longer need ->phy_address and ->mdio_bus fields in
ucc_geth_info structure.
I wish the patch would be a bit shorter, but it seems like the only
way to fix the issue in a sane way. Luckily, the patch has been
tested with real PHYs and fixed-link, so no further regressions
expected.
Reported-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Tested-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MDIO bus drivers for the UCC and gianfar ethernet controllers are
essentially the same. There's no reason to duplicate that much code.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit b31a1d8b41513b96e9c7ec2f68c5734cef0b26a4 ("gianfar: Convert
gianfar to an of_platform_driver") changes the gianfar's phy id to the
format like "mdio@xxxx:xx", but uec still uses the old format like
"xxxxxxxx:xx". For the board whose UEC uses gianfar-mdio like
MPC8568MDS, the phy can not be attached because of the incompatible
phy id format. This patch changes uec's phy id to the same format as
gianfar's.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The UCC Event Register (UCCE) already has unambigous macro definitions in qe.h,
so we should not be defining our own in the UCC Ethernet driver.
Removed unused local variable 'dev' from ucc_geth_poll(), which fixes
a warning caused by commit 908a7a16b852ffd618a9127be8d62432182d81b4
("net: Remove unused netdev arg from some NAPI interfaces.").
Replaced in_be/out_be pairs with setbits32 or clrbits32, where applicable.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The timeout handling code is currently broken in several ways:
- It calls stop() (which frees all the memory and IRQ), and then
calls startup() (which won't re-request IRQ, neither it will
re-init the Fast UCC structure).
- It calls these routines from the softirq context, which is wrong,
since stop() calls free_irq() (which might sleep) and startup()
allocates things with GFP_KERNEL.
- It won't soft-reset the PHY. We need the PHY reset for at least
MPC8360E-MDS boards with Marvell 88E1111 PHY, the PHY won't recover
from timeouts w/o the reset.
So the patch fixes these problems by implementing the workqueue for the
timeout handling, and there we fully re-open the device via close() and
open() calls. The close/open paths do the right things, and I can see
that the driver actually survive the timeouts.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ucc_geth didn't have anything marked as __iomem. It was also inconsistent
with its use of in/out accessors (using them sometimes, not using them other
times). Cleaning this up cuts the warnings down from hundreds to just over a
dozen.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Having the id field be an int was making more complex bus topologies
excessively difficult. For now, just convert it to a string, and
change all instances of "bus->id = val" to
snprintf(id, MII_BUS_ID_LEN, "%x", val).
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (408 commits)
[POWERPC] Add memchr() to the bootwrapper
[POWERPC] Implement logging of unhandled signals
[POWERPC] Add legacy serial support for OPB with flattened device tree
[POWERPC] Use 1TB segments
[POWERPC] XilinxFB: Allow fixed framebuffer base address
[POWERPC] XilinxFB: Add support for custom screen resolution
[POWERPC] XilinxFB: Use pdata to pass around framebuffer parameters
[POWERPC] PCI: Add 64-bit physical address support to setup_indirect_pci
[POWERPC] 4xx: Kilauea defconfig file
[POWERPC] 4xx: Kilauea DTS
[POWERPC] 4xx: Add AMCC Kilauea eval board support to platforms/40x
[POWERPC] 4xx: Add AMCC 405EX support to cputable.c
[POWERPC] Adjust TASK_SIZE on ppc32 systems to 3GB that are capable
[POWERPC] Use PAGE_OFFSET to tell if an address is user/kernel in SW TLB handlers
[POWERPC] 85xx: Enable FP emulation in MPC8560 ADS defconfig
[POWERPC] 85xx: Killed <asm/mpc85xx.h>
[POWERPC] 85xx: Add cpm nodes for 8541/8555 CDS
[POWERPC] 85xx: Convert mpc8560ads to the new CPM binding.
[POWERPC] mpc8272ads: Remove muram from the CPM reg property.
[POWERPC] Make clockevents work on PPC601 processors
...
Fixed up conflict in Documentation/powerpc/booting-without-of.txt manually.
|
|
We now have struct net_device_stats embedded in struct net_device,
and the default ->get_stats() hook does the obvious thing for us.
Run through drivers/net/* and remove the driver-local storage of
statistics, and driver-local ->get_stats() hook where applicable.
This was just the low-hanging fruit in drivers/net; plenty more drivers
remain to be updated.
[ Resolved conflicts with napi_struct changes and fix sunqe build
regression... -DaveM ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several devices have multiple independant RX queues per net
device, and some have a single interrupt doorbell for several
queues.
In either case, it's easier to support layouts like that if the
structure representing the poll is independant from the net
device itself.
The signature of the ->poll() call back goes from:
int foo_poll(struct net_device *dev, int *budget)
to
int foo_poll(struct napi_struct *napi, int budget)
The caller is returned the number of RX packets processed (or
the number of "NAPI credits" consumed if you want to get
abstract). The callee no longer messes around bumping
dev->quota, *budget, etc. because that is all handled in the
caller upon return.
The napi_struct is to be embedded in the device driver private data
structures.
Furthermore, it is the driver's responsibility to disable all NAPI
instances in it's ->stop() device close handler. Since the
napi_struct is privatized into the driver's private data structures,
only the driver knows how to get at all of the napi_struct instances
it may have per-device.
With lots of help and suggestions from Rusty Russell, Roland Dreier,
Michael Chan, Jeff Garzik, and Jamal Hadi Salim.
Bug fixes from Thomas Graf, Roland Dreier, Peter Zijlstra,
Joseph Fannin, Scott Wood, Hans J. Koch, and Michael Chan.
[ Ported to current tree and all drivers converted. Integrated
Stephen's follow-on kerneldoc additions, and restored poll_list
handling to the old style to fix mutual exclusion issues. -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes numerous miscellaneous code improvements to the QE library.
1. Remove struct ucc_common and merge ucc_init_guemr() into ucc_set_type()
(every caller of ucc_init_guemr() also calls ucc_set_type()). Modify all
callers of ucc_set_type() accordingly.
2. Remove the unused enum ucc_pram_initial_offset.
3. Refactor qe_setbrg(), also implement work-around for errata QE_General4.
4. Several printk() calls were missing the terminating \n.
5. Add __iomem where needed, and change u16 to __be16 and u32 to __be32 where
appropriate.
6. In ucc_slow_init() the RBASE and TBASE registers in the PRAM were programmed
with the wrong value.
7. Add the protocol type to struct us_info and updated ucc_slow_init() to
use it, instead of always programming QE_CR_PROTOCOL_UNSPECIFIED.
8. Rename ucc_slow_restart_x() to ucc_slow_restart_tx()
9. Add several macros in qe.h (mostly for slow UCC support, but also to
standardize some naming convention) and remove several unused macros.
10. Update ucc_geth.c to use the new macros.
11. Add ucc_slow_info.protocol to specify which QE_CR_PROTOCOL_xxx protcol
to use when initializing the UCC in ucc_slow_init().
12. Rename ucc_slow_pram.rfcr to rbmr and ucc_slow_pram.tfcr to tbmr, since
these are the real names of the registers.
13. Use the setbits, clrbits, and clrsetbits where appropriate.
14. Refactor ucc_set_qe_mux_rxtx().
15. Remove all instances of 'volatile'.
16. Simplify get_cmxucr_reg();
17. Replace qe_mux.cmxucrX with qe_mux.cmxucr[].
18. Updated struct ucc_geth because struct ucc_fast is not padded any more.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The patch enables statistics in ucc_geth and adds ethtool support to
ucc_geth driver.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The rx interrupt coalescing table alignment was "guessed" to be 4,
but should be 64. The size should be 8 * number of queues + 4.
Verified in the MPC8323E manual.
Signed-off-by: Michael Barkowski <Michael.Barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Based partly on the gianfar driver, this patch fixes several
bugs which were causing NAPI to be completely unusable.
* An IRQ is still needed in NAPI, to kick off NAPI task,
and for Tx processing. Request the IRQ.
* If rx_work_limit = 0 we are not complete.
* While running Rx NAPI processing we must mask Rx events,
including Rx busy.
* ucc_geth_rx function does not need a lock.
Could lead to deadlock in NAPI case.
* There's no need to loop reading ucce multiple times in the ISR,
so while adding the call to schedule NAPI which was not there,
simplify the event processing into if-else format.
* Rx Busy now kicks off NAPI processing, while still
being counted as an error.
Signed-off-by: Michael Reiss <michael.f.reiss@freescale.com>
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
migrate ucc_geth to use the common phylib code.
There are several side effects from doing this:
o deprecate 'interface' property specification present
in some old device tree source files in
favour of a split 'max-speed' and 'interface-type'
description to appropriately match definitions
in include/linux/phy.h. Note that 'interface' property
is still honoured if max-speed or interface-type
are not present (backward compatible).
o compile-time CONFIG_UGETH_HAS_GIGA is eliminated
in favour of probe time speed derivation logic.
o adjust_link streamlined to only operate on maccfg2
and upsmr.r10m, instead of reapplying static initial
values related to the interface-type.
o Addition of UEC MDIO of_platform driver requires
platform code add 'mdio' type to id list
prior to calling of_platform_bus_probe (separate patch).
o ucc_struct_init introduced to reduce ucc_geth_startup
complexity.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
changes due to qe_lib changes include:
o removed inclusion of platform header file
o removed platform_device code, replaced with of_device
o removed typedefs
o uint -> u32 conversions
o removed following defines:
QE_SIZEOF_BD, BD_BUFFER_ARG, BD_BUFFER_CLEAR, BD_BUFFER,
BD_STATUS_AND_LENGTH_SET, BD_STATUS_AND_LENGTH, and BD_BUFFER_SET
because they hid sizeof/in_be32/out_be32 operations from the reader.
o removed irrelevant comments, added others to resemble removed BD_ defines
o const'd and uncasted all get_property() assignments
bugfixes, courtesy of Scott Wood, include:
- Read phy_address as a u32, not u8.
- Match on type == "network" as well as compatible == "ucc_geth", as
device_is_compatible() will only compare up to the length of the
test string, allowing "ucc_geth_phy" to match as well.
- fixes the MAC setting code in ucc_geth.c. The old code was overwriting and dereferencing random stack contents.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
QE(QUICC Engine) is a new generation communication coprocessor, which can
be found on some of the latest Freescale PowerQUICC CPUs(e.g. MPC8360).
The UCC(Unified Communications Controller) module of QE can work as gigabit
Ethernet device. This patch provides driver for the device.
Signed-off-by: Shlomi Gridish <gridish@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
Jeff Kirsher
Lucas De Marchi
Yang Li
Eric Dumazet
Dave Liu
André Goddard Rosa
Anton Vorontsov
Linus Torvalds
Haiying Wang
Grant Likely
Joakim Tjernlund
Kumar Gala
David S. Miller
Andy Fleming
Timur Tabi
Linus Torvalds
Jeff Garzik
Stephen Hemminger
Michael Barkowski
Michael Reiss
Kim Phillips