| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hostap_80211_rx() function is supposed to set up the mac addresses
for four possible cases, based on two bits of input data. For
some reason, gcc decides that it's possible that none of the these
four cases apply and the addresses remain uninitialized:
drivers/net/wireless/intersil/hostap/hostap_80211_rx.c: In function ‘hostap_80211_rx’:
arch/x86/include/asm/string_32.h:77:14: warning: ‘src’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/net/wireless/intel/ipw2x00/libipw_rx.c: In function ‘libipw_rx’:
arch/x86/include/asm/string_32.h:77:14: error: ‘dst’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
arch/x86/include/asm/string_32.h:78:22: error: ‘*((void *)&dst+4)’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
This warning is clearly nonsense, but changing the last case into
'default' makes it obvious to the compiler too, which avoids the
warning and probably leads to better object code too.
The same code is duplicated several times in the kernel, so this
patch uses the same workaround for all copies. The exact configuration
was hit only very rarely in randconfig builds and I only saw it
in three drivers, but I assume that all of them are potentially
affected, and it's better to keep the code consistent.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
SDIO ID 0271:0418
Signed-off-by: Alan Cox <alan@linux.intel.com>
Bugzilla-ID: https://bugzilla.kernel.org/show_bug.cgi?id=67921
Reviewed-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
When power is removed from the device, all of the SDIO settings
return to default. Fix that by reconfiguring after power is
applied.
Signed-off-by: James Minor <james.minor@ni.com>
Reviewed-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This allows the hardware to be restarted, as it will cause the
sg to be reinitialized.
Signed-off-by: James Minor <james.minor@ni.com>
Reviewed-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
To reuse the busreqs in case of hardware restart, they must be
properly reinitialized. If the scat_req pointer isn't reset to
0, __ath6kl_sdio_write_async() will assume there is sg work to be
done (causing a kernel OOPS).
Signed-off-by: James Minor <james.minor@ni.com>
Reviewed-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
When building with W=1, we got one warning as belows:
drivers/net/wireless/ath/ath6kl/wmi.c:3509:6: warning: variable ‘ret’
set but not used [-Wunused-but-set-variable]
At the end of ath6kl_wmi_set_pvb_cmd, it is returned by 0 regardless of
return value of ath6kl_wmi_cmd_send.
This patch fixes return value from 0 to ret that has result of
ath6kl_wmi_cmd_send execution.
Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The ath6kl driver attempts to get the txpower value from the radio by first
clearing the existing stored value and then watching the value to become
non-zero.
APs allow setting client power to values from -127..127, but this radio
is not capable of setting values less then 0 and so will report txpower
as 0dbm for both negative and 0 client power values.
When the radio has txpower set to 0dbm txpower (equivalent to 1mw) the
ath6kl_cfg80211_get_txpower() function will remain in the
wait_event_interruptible_timeout() loop waiting for the value to be
non-zero, and will eventually timeout. This results in a 5 second delay in
response. However, the correct value of zero is eventually returned.
The 6004 defaults to 63dbm which is then limited by regulatory and
hardware limits with max of 18dbm (6003 max is 16dbm), therefore we can
use values larger then these to be able to determine when the value has
been updated.
To correct the issue, set the value to a nonsensical value (255) and wait
for it to change to the valid value.
Tested on both 6003 and 6004 based radios. Return value of zero is
correctly returned in an expected amount of time (similar to when
returning non-zero values) when AP client power is set to both 0 and
negative values.
Signed-off-by: Eric Bentley <eric.bentley@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The firmware crash dumps on the 6004 are the same as the 6003. Remove the
statement guarding it from dumping on the 6004. Renamed the
REG_DUMP_COUNT_AR6003 to reflect support on both chips.
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
Reviewed-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The use of config_enabled() against config options is ambiguous. In
practical terms, config_enabled() is equivalent to IS_BUILTIN(), but the
author might have used it for the meaning of IS_ENABLED(). Using
IS_ENABLED(), IS_BUILTIN(), IS_MODULE() etc. makes the intention
clearer.
This commit replaces config_enabled() with IS_ENABLED() where possible.
This commit is only touching bool config options.
I noticed two cases where config_enabled() is used against a tristate
option:
- config_enabled(CONFIG_HWMON)
[ drivers/net/wireless/ath/ath10k/thermal.c ]
- config_enabled(CONFIG_BACKLIGHT_CLASS_DEVICE)
[ drivers/gpu/drm/gma500/opregion.c ]
I did not touch them because they should be converted to IS_BUILTIN()
in order to keep the logic, but I was not sure it was the authors'
intention.
Link: http://lkml.kernel.org/r/1465215656-20569-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Stas Sergeev <stsp@list.ru>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: "Dmitry V. Levin" <ldv@altlinux.org>
Cc: yu-cheng yu <yu-cheng.yu@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Will Drewry <wad@chromium.org>
Cc: Nikolay Martynov <mar.kolya@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: James Cowgill <James.Cowgill@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Tony Wu <tung7970@gmail.com>
Cc: Huaitong Han <huaitong.han@intel.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: "Maciej W. Rozycki" <macro@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When an NL80211_DISCONNECT is sent to cfg80211, the driver's cfg80211
disconnect function sets the sme_state to SME_DISCONNECTED before receiving
a WMI_DISCONNECT_EVENT from the firmware. This caused cfg80211 to not know
that the connection is disconnected because the driver fails to notify
cfg80211 upon receiving WMI_DISCONNECT_EVENT from the firmware believing
it is already disconnected.
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
When disabling tethering after having enabled it, the ath6kl driver does
not set the IFF_LOWER_UP flag to 0 (carrier off) on the wlan interface.
The upper layers (eg. connman) are not notified of the tethering mode
status change. So, tethering can not be activated anymore.
This patch adds a netif_carrier_off() call when stopping AP mode to fix
the problem.
Signed-off-by: Pierre Le Magourou <plemagourou@aldebaran.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
One minute after a successful connection, the kernel checks if the
frequency and the channel width are well configured for the country we
are in. (regulatory domain)
ath6kl driver was setting the NL80211_CHAN_HT20 channel without checking
for the HT capabilities. (we should have NL80211_CHAN_NO_HT in our
case because the firmware did not support HT)
This patch adds a check on ht_cap.ht_supported in order to create the
channel corresponding to the firmware capabilities.
Signed-off-by: Pierre Le Magourou <plemagourou@aldebaran.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
When enabling WLAN tethering, a new AP is visible and a STA could
connect to it. When the STA tries to authenticate to the newly created
AP, the WPA authentication mechanism is stuck in the 1/4 msg of 4-Way
Handshake.
In ath6kl_rx(), the ath6kl_find_sta() function is looking for the
h_source field of the Ethernet frame header received by the STA. The
datap pointer that points to the Ethernet frame header is incorrect,
and was pointing at the wrong offset in the buffer.
This commit adds a pad_before_data_start offset to set the datap pointer
to the Ethernet frame header. datap->h_source parameter is now really
pointing to the source ethernet address and the authentication process
can continue.
Signed-off-by: Pierre Le Magourou <plemagourou@aldebaran.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Beacon report radio measurement requires reporting observed BSSs
on the channels specified in the beacon request. If the measurement
mode is set to passive or active, it requires actually performing a
scan (passive or active, accordingly), and reporting the time that
the scan was started and the time each beacon/probe was received
(both in terms of TSF of the BSS of the requesting AP). If the
request mode is table, this information is optional.
In addition, the radio measurement request specifies the channel
dwell time for the measurement.
In order to use scan for beacon report when the mode is active or
passive, add a parameter to scan request that specifies the
channel dwell time, and add scan start time and beacon received time
to scan results information.
Supporting beacon report is required for Multi Band Operation (MBO).
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
x <= 7 implies x < 8.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
firmare -> firmware
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
It's useful to permit the customization of the debug uart baud rate. Enable
this and send down the value to the chip if we're enabling debug.
Signed-off-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
For some reason, the 6004 HW 3.0 definition was missing the value for the
uarttx_pin (used for firmware debug). This corrects this situation.
Signed-off-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Certain 6004 firmware releases redefine the WMI_TXE_NOTIFY_EVENTID event
number and sends the new event frequently. However it doesn't have the
tx-err-notify feature and thus this firmware capability flag isn't set on
the firmware package. By guarding the processing of this event by the same
method we guard the sending of the WMI_SET_TXE_NOTIFY_CMDID command, we
can ignore the spurious event that we don't know how to process.
Without this change we call cfg80211_cqm_txe_notify() with possibly bad
data.
Signed-off-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This gives a user a chance to know why a firmware load
is failing.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
My previous patch incorrectly reported the antenna
for 2x2 devices. It should be a mask instead of
a numeric count. This patch fixes that.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
An error message ath6kl_htc_rxmsg_pending_handler isn't appropate for when
the error is ECANCELED. This could be the result of a perfectly appropriate
RX cancel due to shutdown or suspend. This allows the right cleanup to
continue, but without an alarming error message in this particular case.
Signed-off-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
|
|
This supports a way to get target stats through normal
ethtool stats API.
For instance:
# ethtool -S wlan1
NIC statistics:
tx_pkts_nic: 353
tx_bytes_nic: 25142
rx_pkts_nic: 6
rx_bytes_nic: 996
d_tx_ucast_pkts: 89
d_tx_bcast_pkts: 264
d_tx_ucast_bytes: 3020
d_tx_bcast_bytes: 22122
...
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This will allow us to call it from elsewhere when implementing
ethtool stats.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Improper use of strlcpy caused garbage to be appended to the
firmware version string. Fix this by paying attention to the
ie_lenth.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
It can take a user a while to understand why their
NIC that advertises 802.11n support cannot actually
do 802.11n. Print out a warning in the logs to save
the next poor person to use this NIC some trouble.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This lets 'iw phy phy0 info' report antennas for
the radio device:
...
Available Antennas: TX 0x2 RX 0x2
Configured Antennas: TX 0x2 RX 0x2
...
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Kalle Valo says:
====================
here's a bigger pull request for 4.4. The diffstat looks scary as we
created a new directory realtek for all realtek drivers. In the future
I'm planning to create similar directories for all vendors, currently we
just have ath, mediatek and realtek. This change has been in linux-next
for a couple of weeks so it should be safe, but of course you never
know.
There's also a new driver rtl8xxxu for few realtek USB devices. This
just made it to the last linux-next build.
Otherwise there's nothing really special, more info below. If time
permits, and it's ok for you, I'm hoping to send you a one more pull
request this week.
brcmfmac
* using netdev carrier state
* add and rework some cfg80211 callbacks mainly for AP mode
* use devcoredump when triggered by firmware event
realtek
* create new directory drivers/net/wireless/realtek/ for all realtek
drivers, not visible to users (no kconfig changes etc)
* add rtl8xxxu, a new mac80211 driver for RTL8723AU, RTL8188CU,
RTL8188RU, RTL8191CU, RTL8192CU and hopefully more in the future
ath10k
* add board 2 API support for automatically choosing correct board file
* data path optimisations
* disable PCI power save for qca988x and QCA99x0 due to interop reasons
wil6210
* BlockAckReq support
* firmware crashdump using devcoredump
* capture all frames with sniffer
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
for_each_compatible_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression e;
local idexpression n;
@@
for_each_compatible_node(n,...) {
... when != of_node_put(n)
when != e = n
(
return n;
|
+ of_node_put(n);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the option to configure multiple 'scan plans' for scheduled scan.
Each 'scan plan' defines the number of scan cycles and the interval
between scans. The scan plans are executed in the order they were
configured. The last scan plan will always run infinitely and thus
defines only the interval between scans.
The maximum number of scan plans supported by the device and the
maximum number of iterations in a single scan plan are advertised
to userspace so it can configure the scan plans appropriately.
When scheduled scan results are received there is no way to know which
scan plan is being currently executed, so there is no way to know when
the next scan iteration will start. This is not a problem, however.
The scan start timestamp is only used for flushing old scan results,
and there is no difference between flushing all results received until
the end of the previous iteration or the start of the current one,
since no results will be received in between.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
WARN_ON() already contain an unlikely compiler flag. Drop it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The check for send_pkt being NULL is redundant before the call
to htc_reclaim_txctrl_buf, therefore it should be removed. This was
detected by static analysis by cppcheck.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Pull networking updates from David Miller:
"Another merge window, another set of networking changes. I've heard
rumblings that the lightweight tunnels infrastructure has been voted
networking change of the year. But what do I know?
1) Add conntrack support to openvswitch, from Joe Stringer.
2) Initial support for VRF (Virtual Routing and Forwarding), which
allows the segmentation of routing paths without using multiple
devices. There are some semantic kinks to work out still, but
this is a reasonably strong foundation. From David Ahern.
3) Remove spinlock fro act_bpf fast path, from Alexei Starovoitov.
4) Ignore route nexthops with a link down state in ipv6, just like
ipv4. From Andy Gospodarek.
5) Remove spinlock from fast path of act_gact and act_mirred, from
Eric Dumazet.
6) Document the DSA layer, from Florian Fainelli.
7) Add netconsole support to bcmgenet, systemport, and DSA. Also
from Florian Fainelli.
8) Add Mellanox Switch Driver and core infrastructure, from Jiri
Pirko.
9) Add support for "light weight tunnels", which allow for
encapsulation and decapsulation without bearing the overhead of a
full blown netdevice. From Thomas Graf, Jiri Benc, and a cast of
others.
10) Add Identifier Locator Addressing support for ipv6, from Tom
Herbert.
11) Support fragmented SKBs in iwlwifi, from Johannes Berg.
12) Allow perf PMUs to be accessed from eBPF programs, from Kaixu Xia.
13) Add BQL support to 3c59x driver, from Loganaden Velvindron.
14) Stop using a zero TX queue length to mean that a device shouldn't
have a qdisc attached, use an explicit flag instead. From Phil
Sutter.
15) Use generic geneve netdevice infrastructure in openvswitch, from
Pravin B Shelar.
16) Add infrastructure to avoid re-forwarding a packet in software
that was already forwarded by a hardware switch. From Scott
Feldman.
17) Allow AF_PACKET fanout function to be implemented in a bpf
program, from Willem de Bruijn"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1458 commits)
netfilter: nf_conntrack: make nf_ct_zone_dflt built-in
netfilter: nf_dup{4, 6}: fix build error when nf_conntrack disabled
net: fec: clear receive interrupts before processing a packet
ipv6: fix exthdrs offload registration in out_rt path
xen-netback: add support for multicast control
bgmac: Update fixed_phy_register()
sock, diag: fix panic in sock_diag_put_filterinfo
flow_dissector: Use 'const' where possible.
flow_dissector: Fix function argument ordering dependency
ixgbe: Resolve "initialized field overwritten" warnings
ixgbe: Remove bimodal SR-IOV disabling
ixgbe: Add support for reporting 2.5G link speed
ixgbe: fix bounds checking in ixgbe_setup_tc for 82598
ixgbe: support for ethtool set_rxfh
ixgbe: Avoid needless PHY access on copper phys
ixgbe: cleanup to use cached mask value
ixgbe: Remove second instance of lan_id variable
ixgbe: use kzalloc for allocating one thing
flow: Move __get_hash_from_flowi{4,6} into flow_dissector.c
ixgbe: Remove unused PCI bus types
...
|
|
Looks like the word "contiguous" is often mistyped.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
This fixes two misspellings of "distribution" in a comment.
Signed-off-by: Nik Nyby <nikolas@gnu.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Major changes:
wil6210:
* add modparam for bcast ring size
* support hidden SSID
* add per-MCS Rx stats
|
|
When one client is associated and connected to an ar6003 hw version
2.0 with firmware 3.1.1.149, and another client tries to connect, the
first client's MAC address is lost in the station list because the
"aid" is always "1". The structure "wmi_connect_event" has the "aid"
as the second byte in the message, but it should be the first byte.
This patch has been tested with linux-3.10.40
Signed-off-by: Brent Taylor <motobud@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
When we disconnect from the AP, drivers call cfg80211_disconnect().
This doesn't know whether the disconnection was initiated locally
or by the AP though, which can cause problems with the supplicant,
for example with WPS. This issue obviously doesn't show up with any
mac80211 based driver since mac80211 doesn't call this function.
Fix this by requiring drivers to indicate whether the disconnect is
locally generated or not. I've tried to update the drivers, but may
not have gotten the values correct, and some drivers may currently
not be able to report correct values. In case of doubt I left it at
false, which is the current behaviour.
For libertas, make adjustments as indicated by Dan Williams.
Reported-by: Matthieu Mauger <matthieux.mauger@intel.com>
Tested-by: Matthieu Mauger <matthieux.mauger@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Johannes Berg says:
====================
Lots of updates for net-next; along with the usual flurry
of small fixes, cleanups and internal features we have:
* VHT support for TDLS and IBSS (conditional on drivers though)
* first TX performance improvements (the biggest will come later)
* many suspend/resume (race) fixes
* name_assign_type support from Tom Gundersen
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This will expose in /sys whether the ifname of a device is set by
userspace or generated by the kernel. The latter kind (wlanX, etc)
is not deterministic, so userspace needs to rename these devices
to names that are guaranteed to stay the same between reboots. The
former, however should never be renamed, so userspace needs to be
able to reliably tell the difference.
Similar functionality was introduced for the rtnetlink core in
commit 5517750f058e ("net: rtnetlink - make create_link take name_assign_type")
Signed-off-by: Tom Gundersen <teg@jklm.no>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Cc: Hante Meuleman <meuleman@broadcom.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
[reformat changelog to fit 72 cols]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Use the built-in function instead of memset.
Miscellanea:
Add #include <linux/etherdevice.h> where appropriate
Use ETH_ALEN instead of 6
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
802.11ad adds new a network type (PBSS) and changes the capability
field interpretation for the DMG (60G) band.
The same 2 bits that were interpreted as "ESS" and "IBSS" before are
re-used as a 2-bit field with 3 valid values (and 1 reserved). Valid
values are: "IBSS", "PBSS" (new) and "AP".
In order to get the BSS struct for the new PBSS networks, change the
cfg80211_get_bss() function to take a new enum ieee80211_bss_type
argument with the valid network types, as "capa_mask" and "capa_val"
no longer work correctly (the search must be band-aware now.)
The remaining bits in "capa_mask" and "capa_val" are used only for
privacy matching so replace those two with a privacy enum as well.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
[rewrite commit log, tiny fixes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
For some reason, we made the bandwidth separate flags, which
is rather confusing - a single rate cannot have different
bandwidths at the same time.
Change this to no longer be flags but use a separate field
for the bandwidth ('bw') instead.
While at it, add support for 5 and 10 MHz rates - these are
reported as regular legacy rates with their real bitrate,
but tagged as 5/10 now to make it easier to distinguish them.
In the nl80211 API, the flags are preserved, but the code
now can also clearly only set a single one of the flags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This is really just duplicating the list of information that's
already available in the nl80211 attribute, so remove the list.
Two small changes are needed:
* remove STATION_INFO_ASSOC_REQ_IES complete, but the length
(assoc_req_ies_len) can be used instead
* add NL80211_STA_INFO_RX_DROP_MISC which exists internally
but not in nl80211 yet
This gets rid of the duplicate maintenance of the two lists.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Kalle Valo <kvalo@qca.qualcomm.com> says:
"One ath6kl patch and rest for ath10k, but nothing really major which
stands out. Most notable:
o fix resume (Bartosz)
o firmware restart is now faster and more reliable (Michal)
o it's now possible to test hardware restart functionality without
crashing the firmware using hw-restart parameter with
simulate_fw_crash debugfs file (Michal)"
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Johannes Berg <johannes@sipsolutions.net> says:
"This relatively large batch of changes is comprised of the
following:
* large mac80211-hwsim changes from Ben, Jukka and a bit myself
* OCB/WAVE/11p support from Rostislav on behalf of the Czech Technical
University in Prague and Volkswagen Group Research
* minstrel VHT work from Karl
* more CSA work from Luca
* WMM admission control support in mac80211 (myself)
* various smaller fixes, spelling corrections, and minor API additions"
Conflicts:
drivers/net/wireless/ath/wil6210/cfg80211.c
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Existing implementation of reset_resume handler just calls
ath6kl_usb_remove() that deallocates all resources.
It can lead to double free, etc. on disconnect.
The patch removes reset_resume handler,
so usb core could conservatively reset the driver.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
David S. Miller
Arnd Bergmann
Adam Williamson
James Minor
Chaehyun Lim
Eric Bentley
Dan Kephart
Masahiro Yamada
Pierre Le Magourou
Avraham Stern
Heinrich Schuchardt
Julia Lawall
Steve deRosier
Johannes Berg
Ben Greear
Geliang Tang
Colin Ian King
Linus Torvalds
Nik Nyby
Kalle Valo
Brent Taylor
Tom Gundersen
Joe Perches
Dedy Lansky
John W. Linville
Alexey Khoroshilov