aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/ath
AgeCommit message (Collapse)AuthorFilesLines
2014-11-11ath9k_htc: remove return of value in empty definintion of ath9k_htc_deinit_debugJohn W. Linville1-1/+3
Cc: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-11ath9k_htc: add spectral scan debug interfaceOleksij Rempel3-0/+9
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-11ath9k_htc: process rx spectral packetsOleksij Rempel1-0/+14
use code provided by Ashish Patro <patro@cs.wisc.edu> Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-11ath9k_htc: trigger spectral scan on set_channelOleksij Rempel1-0/+4
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-11ath9k_htc: set initial spec_config valuesOleksij Rempel1-0/+8
use values provided by Ashish Patro <patro@cs.wisc.edu> Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-11ath9k_htc: add struct ath_spec_scan_priv to ath9k_htc_privOleksij Rempel1-0/+1
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-11ath9k_htc: add ath_ps_ops bindingsOleksij Rempel1-0/+16
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-11ath9k_htc: fix rs_datalen conversationOleksij Rempel1-1/+1
For some reason it didn't coused obvious problems. Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-11ath9k: For AR9271 chipsets, set count = 0 for endless samples.Oleksij Rempel1-3/+6
not sure why. Initially provided by Ashish Patro <patro@cs.wisc.edu> Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-11ath9k: move spectral.* to common-spectral.*Oleksij Rempel8-25/+31
and rename exports from ath9k_spectral_* to ath9k_cmn_spectral_* Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-11ath9k: move ath9k_spectral_scan_ from main.c to spectral.cOleksij Rempel2-70/+70
Now we should be ready to make this code common. Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-11ath9k: make ath9k_spectral_scan_ do not depend on ath_softcOleksij Rempel4-20/+22
last preparation before moving ath9k_spectral_scan_ to spectral.c Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-11ath9k: use ath_common instead of ieee80211_hw in ath9k_spectral_scan_Oleksij Rempel4-15/+13
we don't have here any ieee80211_hw dependencies any way. Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-11ath9k: use ath_ps_ops in ath9k_spectral_scan_Oleksij Rempel1-4/+4
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-11ath9k: add ath_ps_ops bindingsOleksij Rempel1-0/+16
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-11ath: add struct ath_ps_opsOleksij Rempel1-0/+11
we will need it to make common code Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-11ath9k: remove all struct ath_softc dependencies from spectral codeOleksij Rempel4-50/+51
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-11ath9k: add ath_hw to ath_spec_scan_privOleksij Rempel2-0/+2
spectral code mostly depends on ath_hw, not on ath_softc Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-11ath9k: use struct dentry by ath9k_spectral_init_debugOleksij Rempel3-9/+9
this will alow us to make ath_softc independent code. Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-11ath9k: move spec_config to ath_spec_scan_privOleksij Rempel5-22/+23
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-11ath9k: move spectral_mode to ath_spec_scan_privOleksij Rempel5-5/+5
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-11ath9k: add struct ath_spec_scan_privOleksij Rempel3-7/+10
and move rfs_chan_spec_scan to this struct. We will need it for common spectral scan code. Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-11ath9k: add support for reporting tx power to mac80211Felix Fietkau3-16/+40
Track it per channel context instead of in the softc Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-11ath9k: Fix RTC_DERIVED_CLK usageMiaoqing Pan2-13/+13
Based on the reference clock, which could be 25MHz or 40MHz, AR_RTC_DERIVED_CLK is programmed differently for AR9340 and AR9550. But, when a chip reset is done, processing the initvals sets the register back to the default value. Fix this by moving the code in ath9k_hw_init_pll() to ar9003_hw_override_ini(). Also, do this override for AR9531. Cc: stable@vger.kernel.org Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-04Merge tag 'mac80211-next-for-john-2014-11-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-nextJohn W. Linville4-7/+12
Johannes Berg <johannes@sipsolutions.net> says: "This relatively large batch of changes is comprised of the following: * large mac80211-hwsim changes from Ben, Jukka and a bit myself * OCB/WAVE/11p support from Rostislav on behalf of the Czech Technical University in Prague and Volkswagen Group Research * minstrel VHT work from Karl * more CSA work from Luca * WMM admission control support in mac80211 (myself) * various smaller fixes, spelling corrections, and minor API additions" Conflicts: drivers/net/wireless/ath/wil6210/cfg80211.c Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-11-04mac80211: replace restart_complete() with reconfig_complete()Eliad Peller2-3/+7
Drivers might want to know also when mac80211 has completed reconfiguring after resume (e.g. in order to know when frames can be passed to mac80211). Rename restart_complete() to a more-generic reconfig_complete(), and add a new enum to indicate the reconfiguration type. Update the current users with the new prototype. Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-11-03Merge branch 'platform/remove_owner' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux into driver-core-nextGreg Kroah-Hartman2-2/+0
Remove all .owner fields from platform drivers
2014-11-04ath10k: fix pm resume after suspendBartosz Markowski1-4/+14
Firmware was crashing when we were trying to warm reset it after suspend. This was due to the fact that target registeres can be accessed only if the hardware is awaken. This patch makes sure to awake the device also on the hif up, not only in case of probe call. Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-11-04ath6kl: remove incorrect reset_resume handlerAlexey Khoroshilov1-9/+0
Existing implementation of reset_resume handler just calls ath6kl_usb_remove() that deallocates all resources. It can lead to double free, etc. on disconnect. The patch removes reset_resume handler, so usb core could conservatively reset the driver. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-31ath10k: speed up hw recoveryMichal Kazior7-5/+47
In some cases hw recovery was taking an absurdly long time due to ath10k waiting for things that would never really complete. Instead of waiting for inevitable timeouts poke all completions and wakequeues and check if it's still worth waiting. Reading/writing ar->state requires conf_mutex. Since waiters might be holding it introduce a new flag CRASH_FLUSH so it's possible to tell waiters to abort whatever they were waiting for. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-31ath10k: expose hw restart via debugfsMichal Kazior1-1/+6
Until now it was possible to simulate soft and hard fw crashes but it wasn't possible to trigger an immediately hw restart itself (without the fw crash). This can be useful when stress testing hw restarting stability, e.g. during heavy tx/rx traffic. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-31ath10k: fix possible bmi crashMichal Kazior2-0/+10
While testing other things I've found that CE items aren't cleared properly. This could lead to null dereferences in BMI. To prevent that make sure CE revoking clears the nbytes value (which is used as a buffer completion indication) and memset the entire CE ring data shared between host and target when (re)initializing. Also make sure to check BMI xfer pointer and print a splat instead of crashing the kernel. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-31ath10k: don't reset chip on power_downMichal Kazior1-1/+3
Currently hif_power_up performs effectively a reset and hif_stop resets the chip as well so there's no point in resetting here. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-31ath10k: split reset logic from power upMichal Kazior1-71/+80
The power up procedure was overly complex due to warm/cold reset workarounds and issues. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-31ath10k: make warm reset a bit safer and fasterMichal Kazior1-62/+48
One of the problems with warm reset I've found is that it must be guaranteed that copy engine registers are not being accessed while being reset. Otherwise in worst case scenario the host may lock up. Instead of using sleeps and hoping the device is operational in some arbitrary timeframes use firmware indication register. As a side effect this makes driver boot/stop/recovery faster. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-31ath10k: change ce ring cleanup logicMichal Kazior2-42/+46
Make ath10k_pci_init_pipes() effectively only alter shared target-host data. The per_transfer_context is a host-only thing. It is necessary to preserve it's contents for a more robust ring cleanup. This is required for future warm reset fixes. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-31ath10k: avoid possible deadlock with scan timeoutMichal Kazior1-2/+4
This should prevent deadlock predicted by the following splat: ====================================================== [ INFO: possible circular locking dependency detected ] 3.17.0-wl-ath+ #67 Not tainted ------------------------------------------------------- kworker/u32:1/7230 is trying to acquire lock: (&ar->conf_mutex){+.+.+.}, at: [<ffffffffa040a57d>] ath10k_scan_timeout_work+0x2d/0x50 [ath10k_core] but task is already holding lock: ((&(&ar->scan.timeout)->work)){+.+...}, at: [<ffffffff8106dae1>] process_one_work+0x151/0x470 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 ((&(&ar->scan.timeout)->work)){+.+...}: [<ffffffff810a12e5>] lock_acquire+0x85/0x100 [<ffffffff8106cb4d>] flush_work+0x3d/0x270 [<ffffffff8106e49d>] __cancel_work_timer+0x7d/0x110 [<ffffffff8106e543>] cancel_delayed_work_sync+0x13/0x20 [<ffffffffa0409f16>] ath10k_cancel_remain_on_channel+0x36/0x60 [ath10k_core] [<ffffffffa028c75c>] ieee80211_cancel_roc+0x1cc/0x2f0 [mac80211] [<ffffffffa028c8a2>] ieee80211_mgmt_tx_cancel_wait+0x22/0x30 [mac80211] [<ffffffffa0132288>] nl80211_tx_mgmt_cancel_wait+0xa8/0x130 [cfg80211] [<ffffffff816654a5>] genl_family_rcv_msg+0x1a5/0x3c0 [<ffffffff81665749>] genl_rcv_msg+0x89/0xc0 [<ffffffff81664e91>] netlink_rcv_skb+0xb1/0xc0 [<ffffffff816650bc>] genl_rcv+0x2c/0x40 [<ffffffff8166474d>] netlink_unicast+0x18d/0x200 [<ffffffff81664add>] netlink_sendmsg+0x31d/0x430 [<ffffffff8161a9ac>] sock_sendmsg+0x9c/0xd0 [<ffffffff8161b469>] ___sys_sendmsg+0x389/0x3a0 [<ffffffff8161bed9>] __sys_sendmsg+0x49/0x90 [<ffffffff8161bf32>] SyS_sendmsg+0x12/0x20 [<ffffffff8174c456>] system_call_fastpath+0x1a/0x1f -> #0 (&ar->conf_mutex){+.+.+.}: [<ffffffff810a0bde>] __lock_acquire+0x1b6e/0x1ce0 [<ffffffff810a12e5>] lock_acquire+0x85/0x100 [<ffffffff817491eb>] mutex_lock_nested+0x4b/0x370 [<ffffffffa040a57d>] ath10k_scan_timeout_work+0x2d/0x50 [ath10k_core] [<ffffffff8106db41>] process_one_work+0x1b1/0x470 [<ffffffff8106df63>] worker_thread+0x123/0x460 [<ffffffff81073f34>] kthread+0xe4/0x100 [<ffffffff8174c3ac>] ret_from_fork+0x7c/0xb0 other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock((&(&ar->scan.timeout)->work)); lock(&ar->conf_mutex); lock((&(&ar->scan.timeout)->work)); lock(&ar->conf_mutex); *** DEADLOCK *** Reported-by: Marek Puzyniak <marek.puzyniak@tieto.com> Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-30carl9170: Convert byte_rev_table uses to bitrev8Joe Perches1-2/+2
Use the inline function instead of directly indexing the array. This allows some architectures with hardware instructions for bit reversals to eliminate the array. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-30wil6210: Add support for large packetsVladimir Kondratiev6-7/+38
It is possible to configure driver using mtu_max module parameter by setting it to value in range of 68..7920 inclusive. This is sub-optimal performance-wise in case packet is larger than 1 page. mtu_max default value is 2228. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-30wil6210: improve dmesg for fw error handlingVladimir Kondratiev1-0/+3
In case of FW error, make it clear (in dmesg) what branch is taken in the error recovery code. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-30wil6210: prevent double disconnect command issuingVladimir Kondratiev4-13/+29
Disconnect flow may be invoked either from upper layer request, or from event reported by the firmware. In case of firmware event, driver need to release resources for the station but not send another disconnect WMI command. In case of upper layer request, WMI_DISCONNECT_STA_CMDID command need to be issued for the firmware to perform disconnect on the MAC layer. Eventually, event is expected to confirm MAC disconnect, but it is better to not wait for firmware event and release station resources immediately. FW may fail to report disconnect for various reasons, so one could not rely on event always reported. Introduce parameter to distinguish 2 cases above to prevent double WMI command issuing. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-30wil6210: reset flow updatesVladimir Kondratiev2-5/+24
As communicated with the firmware & hardware teams Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-30wil6210: do not attempt FW recovery if interface is downVladimir Kondratiev1-0/+5
When interface is down, recovery flow should not be attempted. Next ndo_open() will trigger target reset, that is FW recovery. Doing recovery while interface is down cause internal "up", leaving internal driver state in conflict with network stack. Then, when network stack will call ndo_open(), kernel oops will be triggered. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-30ath9k: set pulse_rssi threshold to 15Lorenzo Bianconi2-2/+2
Reduce pulse_rssi threshold to 15 in order to improve radar pattern detection probability on ext channel Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-30ath9k: fix some debugfs outputDan Carpenter1-1/+1
The right shift operation has higher precedence than the mask so we left shift by "(i * 3)" and then immediately right shift by "(i * 3)" then we mask. It should be left shift, mask, and then right shift. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-27ath9k: use a random MAC address if the EEPROM address is invalidFelix Fietkau1-2/+11
Based on OpenWrt patch by Gabor Juhos Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-27ath9k: allow disabling bands via platform dataFelix Fietkau3-8/+20
Some devices have multiple bands enables in the EEPROM data, even though they are only calibrated for one. Allow platform data to disable unsupported bands. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-27ath9k: add support for endian swap of eeprom from platform dataFelix Fietkau3-21/+13
On some devices (especially little-endian ones), the flash EEPROM data has a different endian, which needs to be detected. Add a flag to the platform data to allow overriding that behavior Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-27ath9k_hw: start initial NF calibration after PA calibration on <AR9003Felix Fietkau2-2/+6
This makes the initial NF calibration less likely to fail. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-27ath9k_hw: do not run NF and periodic calibration at the same timeFelix Fietkau1-14/+13
It can cause inconsistent calibration results or in some cases turn the radio deaf. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Copyright © 1996 – 2026 Jason A. Donenfeld. All Rights Reverse Engineered.