aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/ath
AgeCommit message (Collapse)AuthorFilesLines
2021-11-17ath11k: add trace log supportVenkateswara Naralasetty5-5/+187
This change is to add trace log support for, * WMI events * WMI commands * ath11k_dbg messages * ath11k_dbg_dump messages * ath11k_log_info messages * ath11k_log_warn messages * ath11k_log_err messages Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00652-QCAHKSWPL_SILICONZ-1 Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1636439755-30419-1-git-send-email-quic_vnaralas@quicinc.com
2021-11-17ath11k: Add missing qmi_txn_cancel()Anilkumar Kolli1-7/+14
Currently many functions do not follow this guidance when qmi_send_request() fails, therefore add missing qmi_txn_cancel() in the qmi_send_request() error path. Also remove initialization on 'struct qmi_txn' since qmi_tx_init() performs all necessary initialization. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1 Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1635857558-21733-1-git-send-email-akolli@codeaurora.org
2021-11-17ath11k: use cache line aligned buffers for dbringRameshkumar Sundaram2-5/+13
The DMA buffers of dbring which is used for spectral/cfr starts at certain offset from original kmalloc() returned buffer. This is not cache line aligned. And also driver tries to access the data that is immediately before this offset address (i.e. buff->paddr) after doing dma map. This will cause cache line sharing issues and data corruption, if CPU happen to write back cache after HW has dma'ed the data. Fix this by mapping a cache line aligned buffer to dma. Tested on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1635831693-15962-1-git-send-email-quic_ramess@quicinc.com
2021-11-17ath11k: Disabling credit flow for WMI pathP Praneesh8-35/+146
Firmware credit flow control is enabled for WMI control services, which expects available tokens should be acquired before sending a command to the target. Also the token gets released when firmware receives the command. This credit-based flow limits driver to send WMI command only when the token available which is causing WMI commands to timeout and return -EAGAIN, whereas firmware has enough capability to process the WMI command. To fix this Tx starvation issue, introduce the ability to disable the credit flow for the WMI path. The driver sends WMI configuration for disabling credit flow to firmware by two ways. 1. By using a global flag (HTC_MSG_SETUP_COMPLETE_EX_ID msg type flags) 2. By using a local flag (ATH11K_HTC_CONN_FLAGS_DISABLE_CREDIT_FLOW_CTRL = 1 << 3) Ath11k uses both these configurations to disable credit flow for the WMI path completely. Also added a hw_param member for credit flow control by which we can enable or disable it based on per-target basis. Currently we are disabling credit flow for IPQ8074, IPQ6018, and QCN9074 as recommended by firmware. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1 Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.4.0.1-00330-QCAHKSWPL_SILICONZ-1 Co-developed-by: Pravas Kumar Panda <kumarpan@codeaurora.org> Signed-off-by: Pravas Kumar Panda <kumarpan@codeaurora.org> Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1635156494-20059-1-git-send-email-quic_ppranees@quicinc.com
2021-11-17ath11k: Fix ETSI regd with weather radar overlapSven Eckelmann1-47/+56
Some ETSI countries have a small overlap in the wireless-regdb with an ETSI channel (5590-5650). A good example is Australia: country AU: DFS-ETSI (2400 - 2483.5 @ 40), (36) (5150 - 5250 @ 80), (23), NO-OUTDOOR, AUTO-BW (5250 - 5350 @ 80), (20), NO-OUTDOOR, AUTO-BW, DFS (5470 - 5600 @ 80), (27), DFS (5650 - 5730 @ 80), (27), DFS (5730 - 5850 @ 80), (36) (57000 - 66000 @ 2160), (43), NO-OUTDOOR If the firmware (or the BDF) is shipped with these rules then there is only a 10 MHz overlap with the weather radar: * below: 5470 - 5590 * weather radar: 5590 - 5600 * above: (none for the rule "5470 - 5600 @ 80") There are several wrong assumption in the ath11k code: * there is always a valid range below the weather radar (actually: there could be no range below the weather radar range OR range could be smaller than 20 MHz) * intersected range in the weather radar range is valid (actually: the range could be smaller than 20 MHz) * range above weather radar is either empty or valid (actually: the range could be smaller than 20 MHz) These wrong assumption will lead in this example to a rule (5590 - 5600 @ 20), (N/A, 27), (600000 ms), DFS, AUTO-BW which is invalid according to is_valid_reg_rule() because the freq_diff is only 10 MHz but the max_bandwidth is set to 20 MHz. Which results in a rejection like: WARNING: at backports-20210222_001-4.4.60-b157d2276/net/wireless/reg.c:3984 [...] Call trace: [<ffffffbffc3d2e50>] reg_get_max_bandwidth+0x300/0x3a8 [cfg80211] [<ffffffbffc3d3d0c>] regulatory_set_wiphy_regd_sync+0x3c/0x98 [cfg80211] [<ffffffbffc651598>] ath11k_regd_update+0x1a8/0x210 [ath11k] [<ffffffbffc652108>] ath11k_regd_update_work+0x18/0x20 [ath11k] [<ffffffc0000a93e0>] process_one_work+0x1f8/0x340 [<ffffffc0000a9784>] worker_thread+0x25c/0x448 [<ffffffc0000aedc8>] kthread+0xd0/0xd8 [<ffffffc000085550>] ret_from_fork+0x10/0x40 ath11k c000000.wifi: failed to perform regd update : -22 Invalid regulatory domain detected To avoid this, the algorithm has to be changed slightly. Instead of splitting a rule which overlaps with the weather radar range into 3 pieces and accepting the first two parts blindly, it must actually be checked for each piece whether it is a valid range. And only if it is valid, add it to the output array. When these checks are in place, the processed rules for AU would end up as country AU: DFS-ETSI (2400 - 2483 @ 40), (N/A, 36), (N/A) (5150 - 5250 @ 80), (6, 23), (N/A), NO-OUTDOOR, AUTO-BW (5250 - 5350 @ 80), (6, 20), (0 ms), NO-OUTDOOR, DFS, AUTO-BW (5470 - 5590 @ 80), (6, 27), (0 ms), DFS, AUTO-BW (5650 - 5730 @ 80), (6, 27), (0 ms), DFS, AUTO-BW (5730 - 5850 @ 80), (6, 36), (N/A), AUTO-BW and will be accepted by the wireless regulatory code. Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211112153116.1214421-1-sven@narfation.org
2021-11-15ath11k: Increment pending_mgmt_tx count before tx send invokeP Praneesh1-2/+4
There is a race condition whereby the tx completion handler can be invoked before the 'num_pending_mgmt_tx" count is incremented. If that occurs, we could get warning trace indicating that 'num_pending_mgmt_tx' is 0 (because it was not yet incremented). Ideally, this trace should be seen only if mgmt tx has not happened but tx completion is received, and it is not expected in this race condition. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01386-QCAHKSWPL_SILICONZ-1 Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org> Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org> Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1635168282-8845-1-git-send-email-quic_ppranees@quicinc.com
2021-11-15ath11k: send proper txpower and maxregpower values to firmwareP Praneesh2-6/+8
Set proper values for max_regpower, max_power, max_antenna_gain as it is because firmware will convert power values to 0.5dbm steps by multiplying it with 2. If txpower is not set, it will lead to cca stuck resulting in latency issues for QCN9074. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01386-QCAHKSWPL_SILICONZ-1 Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org> Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org> Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1635164229-22880-1-git-send-email-quic_ppranees@quicinc.com
2021-11-15ath11k: fix FCS_ERR flag in radio tap headerP Praneesh1-2/+12
In radio tap header, BAD FCS flag is not updated properly because driver failed to update FCS_ERR flag in monitor mode. In rx_desc, FCS_ERR information is available in rx_attention structure and presence of this field indicates corresponding frame failed FCS check. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1 Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1635164060-18423-1-git-send-email-quic_ppranees@quicinc.com
2021-11-15ath11k: move peer delete after vdev stop of station for QCA6390 and WCN6855Wen Gong1-0/+18
When station connect to AP, the wmi command sequence is: peer_create->vdev_start->vdev_up and sequence of station disconnect fo AP is: peer_delete->vdev_down->vdev_stop The sequence of disconnect is not opposite of connect, it caused firmware crash when it handle wmi vdev stop cmd when the AP is support TWT of 802.11 ax, because firmware need access the bss peer for vdev stop cmd. [ 390.438564] ath11k_pci 0000:05:00.0: wmi cmd send 0x6001 ret 0 [ 390.438567] ath11k_pci 0000:05:00.0: WMI peer create vdev_id 0 peer_addr c4:04:15:3b:e0:39 [ 390.472724] ath11k_pci 0000:05:00.0: mac vdev 0 start center_freq 2437 phymode 11ax-he20-2g [ 390.472731] ath11k_pci 0000:05:00.0: wmi cmd send 0x5003 ret 0 [ 390.560849] ath11k_pci 0000:05:00.0: wmi cmd send 0x5005 ret 0 [ 390.560850] ath11k_pci 0000:05:00.0: WMI mgmt vdev up id 0x0 assoc id 1 bssid c4:04:15:3b:e0:39 [ 399.432896] ath11k_pci 0000:05:00.0: WMI peer delete vdev_id 0 peer_addr c4:04:15:3b:e0:39 [ 399.432902] ath11k_pci 0000:05:00.0: wmi cmd send 0x6002 ret 0 [ 399.441380] ath11k_pci 0000:05:00.0: wmi cmd send 0x5007 ret 0 [ 399.441381] ath11k_pci 0000:05:00.0: WMI vdev down id 0x0 [ 399.454681] ath11k_pci 0000:05:00.0: wmi cmd send 0x5006 ret 0 [ 399.454682] ath11k_pci 0000:05:00.0: WMI vdev stop id 0x0 The opposite sequence of disconnect should be: vdev_down->vdev_stop->peer_delete This patch change the sequence of disconnect for station as above opposite sequence for QCA6390, firmware not crash again with this patch. Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1 Signed-off-by: Wen Gong <quic_wgong@quicinc.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211027093825.12167-1-quic_wgong@quicinc.com
2021-11-15ath11k: fix the value of msecs_to_jiffies in ath11k_debugfs_fw_stats_requestWen Gong1-1/+1
parameter of msecs_to_jiffies should be (3 * 1000) instead of (3 * HZ) Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1 Signed-off-by: Wen Gong <quic_wgong@quicinc.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211026032014.27010-1-quic_wgong@quicinc.com
2021-11-15ath11k: remove return for empty tx bitrate in mac_op_sta_statisticsWen Gong1-14/+13
Currently in ath11k_mac_op_sta_statistics() there is the following logic: if (!arsta->txrate.legacy && !arsta->txrate.nss) return; Unfortunately if this condition is true then the function returns without setting parameters that follow the txrate. To address this issue remove the return and instead invert the logic to set the txrate logic if (arsta->txrate.legacy || arsta->txrate.nss). The same was done also in ath10k in commit 1cd6ba8ae33e ("ath10k: remove return for NL80211_STA_INFO_TX_BITRATE"). Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1 Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211011084957.31024-1-wgong@codeaurora.org
2021-11-15ath11k: enable IEEE80211_VHT_EXT_NSS_BW_CAPABLE if NSS ratio enabledWen Gong1-0/+4
When NSS ratio enabled reported by firmware, SUPPORTS_VHT_EXT_NSS_BW is set in ath11k, meanwhile IEEE80211_VHT_EXT_NSS_BW_CAPABLE also need to be set, otherwise it is invalid because spec in IEEE Std 802.11™‐2020 as below. Table 9-273-Supported VHT-MCS and NSS Set subfields, it has subfield VHT Extended NSS BW Capable, its definition is: Indicates whether the STA is capable of interpreting the Extended NSS BW Support subfield of the VHT Capabilities Information field. dmesg have a message without this patch: ieee80211 phy0: copying sband (band 1) due to VHT EXT NSS BW flag It means mac80211 will set IEEE80211_VHT_EXT_NSS_BW_CAPABLE if ath11k not set it in ieee80211_register_hw(). So it is better to set it in ath11k. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211013073704.15888-1-wgong@codeaurora.org
2021-11-15ath11k: avoid unnecessary lock contention in tx_completion pathP Praneesh1-18/+14
Avoid unnecessary idr_find calls before the idr_remove calls. Because idr_remove gives the valid ptr if id is valid otherwise return NULL ptr. So removed the idr_find before idr_remove in tx completion path. Also no need to disable the bottom half preempt if it is already in the bottom half context, so modify the spin_lock_bh to spin_lock in the data tx completion path. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2 Co-developed-by: Karthikeyan Periyasamy <periyasa@codeaurora.org> Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org> Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: P Praneesh <ppranees@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1630560820-21905-13-git-send-email-ppranees@codeaurora.org
2021-11-15ath11k: add branch predictors in dp_tx pathP Praneesh2-29/+25
Add branch prediction in dp_tx code path in tx and tx completion handlers. Also in ath11k_dp_tx_complete_msdu , the pointer that is returned by rcu_dereference() is not dereferenced. so it is preferable to use rcu_access_pointer() here. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2 Co-developed-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: P Praneesh <ppranees@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1630560820-21905-12-git-send-email-ppranees@codeaurora.org
2021-11-15ath11k: avoid while loop in ring selection of tx completion interruptP Praneesh1-5/+4
Currently while loop is used to find the tx completion ring number and it is not required since the tx ring mask and the group id can be combined to directly fetch the ring number. Hence remove the while loop and directly get the ring number from tx mask and group id. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2 Co-developed-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: P Praneesh <ppranees@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1630560820-21905-11-git-send-email-ppranees@codeaurora.org
2021-11-15ath11k: remove mod operator in dst ring processingP Praneesh1-2/+5
Replace use of mod operator with a manual wrap around to avoid additional cost of using mod operation. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2 Co-developed-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: P Praneesh <ppranees@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1630560820-21905-10-git-send-email-ppranees@codeaurora.org
2021-11-15ath11k: allocate HAL_WBM2SW_RELEASE ring from cacheable memoryP Praneesh1-0/+1
Similar to REO destination ring, also allocate HAL_WBM2SW_RELEASE from cacheable memory so that descriptors could be prefetched during tx completion handling. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2 Co-developed-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: P Praneesh <ppranees@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1630560820-21905-9-git-send-email-ppranees@codeaurora.org
2021-11-15ath11k: add branch predictors in process_rxP Praneesh1-15/+9
In datapath, add branch predictors where required in the process rx(). This protects high value rx path without having performance overhead. Also while processing rx packets, the pointer that is returned by rcu_dereference() is not dereferenced. so it is preferable to use rcu_access_pointer() here. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1 Co-developed-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: P Praneesh <ppranees@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1630560820-21905-8-git-send-email-ppranees@codeaurora.org
2021-11-15ath11k: remove usage quota while processing rx packetsP Praneesh1-6/+3
The usage of quota variable inside ath11k_dp_rx_process_received_packets() is redundant. Since we would queue only max packets to the list before calling this function so it would never exceed quota. Hence removing usage of quota variable. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1 Co-developed-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: P Praneesh <ppranees@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1630560820-21905-7-git-send-email-ppranees@codeaurora.org
2021-11-15ath11k: avoid active pdev check for each msduP Praneesh1-36/+34
The Active Pdev and CAC check are done for each msdu in ath11k_dp_rx_process_received_packets which is a overhead. To avoid this overhead, collect all msdus in a per mac msdu list and pass to function. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1 Co-developed-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: P Praneesh <ppranees@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1630560820-21905-6-git-send-email-ppranees@codeaurora.org
2021-11-15ath11k: avoid additional access to ath11k_hal_srng_dst_num_freeP Praneesh1-3/+7
In ath11k_dp_process_rx(), after processing rx_desc from ath11k_hal_srng_dst_get_next_entry(), ath11k_hal_srng_dst_num_free() is accessed everytime because of done flag is not set. To avoid this additional access to ath11k_hal_srng_dst_num_free(), increment total_msdu_reaped only when continuation is not set and update done flag correspondingly. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1 Co-developed-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: P Praneesh <ppranees@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1630560820-21905-5-git-send-email-ppranees@codeaurora.org
2021-11-15ath11k: modify dp_rx desc access wrapper calls inlineP Praneesh1-55/+59
In data path, to reduce the CPU cycles spending on descriptor access wrapper function, changed those functions as static inline. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1 Co-developed-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: P Praneesh <ppranees@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1630560820-21905-4-git-send-email-ppranees@codeaurora.org
2021-11-15ath11k: allocate dst ring descriptors from cacheable memoryP Praneesh6-7/+67
tcl_data and reo_dst rings are currently being allocated using dma_allocate_coherent() which is non cacheable. Allocating ring memory from cacheable memory area allows cached descriptor access and prefetch next descriptors to optimize CPU usage during descriptor processing on NAPI. Based on the hardware param we can enable or disable this feature for the corresponding platform. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1 Co-developed-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org> Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org> Co-developed-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: P Praneesh <ppranees@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1630560820-21905-3-git-send-email-ppranees@codeaurora.org
2021-11-15ath11k: disable unused CE8 interrupts for ipq8074P Praneesh1-1/+1
Host driver doesn't need to process CE8 interrupts (used by target independently) The volume of interrupts is huge within short interval, CPU0 CPU1 CPU2 CPU3 14022188 0 0 0 GIC 71 Edge ce8 Hence disabling unused CE8 interrupt will improve CPU usage. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1 Co-developed-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: P Praneesh <ppranees@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1630560820-21905-2-git-send-email-ppranees@codeaurora.org
2021-11-15ath11k: fix firmware crash during channel switchVenkateswara Naralasetty1-5/+21
Currently the updated bandwidth for the peer will be configured to the firmware after channel switch from the sta_rc_update_wk. If the updated bandwidth is greater than the configured peer phymode during the peer assoc may result firmware assert. For example, initially AP is in HE40 mode and the peer phymode is configured as MODE_11AX_HE40 during peer assoc. Now user change the channel width to HE80 then, the peer bandwidth will be updated as HE80 to the firmware. This will trigger firmware assert due to peer bandwidth is greater than the peer phymode. Fix this issue by sending peer assoc command before setting the updated peer bandwith to firmware. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1636644002-25446-1-git-send-email-quic_vnaralas@quicinc.com
2021-11-15ath11k: Fix 'unused-but-set-parameter' errorSeevalamuthu Mariappan1-1/+0
Below compilation error is reported when built with W=1, drivers/net/wireless/ath/ath11k/mac.c:5408:22: error: parameter 'changed_flags' set but not used [-Werror,-Wunused-but-set-parameter] changed_flags is set, but left unused. So, remove unnecessary set. Compile tested only. Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1636609967-5114-1-git-send-email-quic_seevalam@quicinc.com
2021-11-15ath11k: fix DMA memory free in CE pipe cleanupKarthikeyan Periyasamy1-6/+10
In CE pipe cleanup, DMA memory gets freed by the aligned address (base_addr_owner_space) which is wrong. It needs to be freed by the address (base_addr_owner_space_unaligned) returned by dma_alloc. So free the dma memory by the proper address. This was found in code review. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00729-QCAHKSWPL_SILICONZ-3 v2 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1636561290-18966-1-git-send-email-quic_periyasa@quicinc.com
2021-11-15ath11k: avoid unnecessary BH disable lock in STA kickout eventKarthikeyan Periyasamy1-2/+7
In STA kickout event processing, the peer object is protected under spin lock BH. Release this lock after picking up the vdev_id from the peer object instead after ieee80211_report_low_ack(). This will minimize the lock hold period which will improve performance since base_lock is used across the data path. This was found in code review. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00729-QCAHKSWPL_SILICONZ-3 v2 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1636560388-24955-1-git-send-email-quic_periyasa@quicinc.com
2021-11-15ath11k: fix error routine when fallback of add interface failsKarthikeyan Periyasamy1-7/+7
When there is an error in add interface process from ath11k_mac_set_kickout(), the code attempts to handle a fallback for add_interface. When this fallback succeeds, the driver returns zero rather than error code. This leads to success for the non created VAP. In cleanup, driver gets remove interface callback for the non created VAP and proceeds to self peer delete request which leads to FW assert. Since it was already deleted on the fallback of add interface, return the actual error code instead of fallback return code. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00729-QCAHKSWPL_SILICONZ-3 v2 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1636558557-2874-1-git-send-email-quic_periyasa@quicinc.com
2021-11-15ath11k: fix fw crash due to peer get authorized before key installKarthikeyan Periyasamy2-7/+47
Firmware expects host to authorize the peer after the successful key install. But host authorize the peer before the key install, this trigger the firmware assert which leads to Q6 crash. To avoid this Q6 crash, host should authorize the peer after the key install. So introduce is_authorized in peer object to identify that peer is authorize or not. When IEEE80211_STA_CONTROL_PORT flag is unset, peer move to authorize state before the vdev up. When the same flag is set then peer move to authorize state after vdev up. So added authorise check in ath11k_bss_assoc() to handle the earlier state transition case. Also added the WMI authorize procedure in ath11k_mac_op_sta_state() to handle the non-earlier state transition case. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1636554200-12345-1-git-send-email-quic_periyasa@quicinc.com
2021-11-12ath11k: Clear auth flag only for actual association in security modeRameshkumar Sundaram3-1/+5
AUTH flag is needed when peer assoc command is sent from host in security mode for non-assoc cases. Firmware will handle AUTH flag when client is associating as AUTH flag will be set after key exchange. For internally provided peer assoc commands from host, there won't be any key exchange, so AUTH flag is expected to be set in host. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1 Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org> Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org> Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1635177786-20854-1-git-send-email-quic_ramess@quicinc.com
2021-11-12ath11k: Send PPDU_STATS_CFG with proper pdev mask to firmwareRameshkumar Sundaram2-2/+3
HTT_PPDU_STATS_CFG_PDEV_ID bit mask for target FW PPDU stats request message was set as bit 8 to 15. Bit 8 is reserved for soc stats and pdev id starts from bit 9. Hence change the bitmask as bit 9 to 15 and fill the proper pdev id in the request message. In commit 701e48a43e15 ("ath11k: add packet log support for QCA6390"), both HTT_PPDU_STATS_CFG_PDEV_ID and pdev_mask were changed, but this pdev_mask calculation is not valid for platforms which has multiple pdevs with 1 rxdma per pdev, as this is writing same value(i.e. 2) for all pdevs. Hence fixed it to consider pdev_idx as well, to make it compatible for both single and multi pd cases. Tested on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01092-QCAHKSWPL_SILICONZ-1 Tested on: IPQ6018 hw1.0 WLAN.HK.2.5.0.1-01067-QCAHKSWPL_SILICONZ-1 Fixes: 701e48a43e15 ("ath11k: add packet log support for QCA6390") Co-developed-by: Sathishkumar Muruganandam <murugana@codeaurora.org> Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org> Signed-off-by: Rameshkumar Sundaram <ramess@codeaurora.org> Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210721212029.142388-10-jouni@codeaurora.org
2021-11-12ar5523: Fix null-ptr-deref with unexpected WDCMSG_TARGET_START replyZekun Shen1-0/+4
Unexpected WDCMSG_TARGET_START replay can lead to null-ptr-deref when ar->tx_cmd->odata is NULL. The patch adds a null check to prevent such case. KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007] ar5523_cmd+0x46a/0x581 [ar5523] ar5523_probe.cold+0x1b7/0x18da [ar5523] ? ar5523_cmd_rx_cb+0x7a0/0x7a0 [ar5523] ? __pm_runtime_set_status+0x54a/0x8f0 ? _raw_spin_trylock_bh+0x120/0x120 ? pm_runtime_barrier+0x220/0x220 ? __pm_runtime_resume+0xb1/0xf0 usb_probe_interface+0x25b/0x710 really_probe+0x209/0x5d0 driver_probe_device+0xc6/0x1b0 device_driver_attach+0xe2/0x120 I found the bug using a custome USBFuzz port. It's a research work to fuzz USB stack/drivers. I modified it to fuzz ath9k driver only, providing hand-crafted usb descriptors to QEMU. After fixing the code (fourth byte in usb packet) to WDCMSG_TARGET_START, I got the null-ptr-deref bug. I believe the bug is triggerable whenever cmd->odata is NULL. After patching, I tested with the same input and no longer see the KASAN report. This was NOT tested on a real device. Signed-off-by: Zekun Shen <bruceshenzk@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/YXsmPQ3awHFLuAj2@10-18-43-117.dynapool.wireless.nyu.edu
2021-11-10ath11k: enable 802.11 power save mode in station modeCarl Huang4-0/+94
To reduce power consumption enable 802.11 power save mode in station mode. This allows both radio and CPU to sleep more. Only enable the mode on QCA6390 and WCN6855, it's unknown how other hardware families support this feature. To test that power save mode is running run "iw dev wls1 set power_save off", check there is no NULL Data frame seen by a sniffer. And run "iw dev wls1 set power_save on" and check there is a NULL Data frame in sniffer. Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1 Signed-off-by: Carl Huang <cjhuang@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211108123826.8463-2-kvalo@codeaurora.org
2021-11-10ath11k: convert ath11k_wmi_pdev_set_ps_mode() to use enum wmi_sta_ps_modeKalle Valo3-5/+8
It's more descriptive to use the actual enum used by the firmware instead of a boolean so change ath11k_wmi_pdev_set_ps_mode() to use a boolean. Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1 Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211108123826.8463-1-kvalo@codeaurora.org
2021-11-08wcn36xx: fix RX BD rate mapping for 5GHz legacy ratesBenjamin Li1-3/+1
The linear mapping between the BD rate field and the driver's 5GHz legacy rates table (wcn_5ghz_rates) does not only apply for the latter four rates -- it applies to all eight rates. Fixes: 6ea131acea98 ("wcn36xx: Fix warning due to bad rate_idx") Signed-off-by: Benjamin Li <benl@squareup.com> Tested-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211104010548.1107405-3-benl@squareup.com
2021-11-08wcn36xx: populate band before determining rate on RXBenjamin Li1-18/+19
status.band is used in determination of status.rate -- for 5GHz on legacy rates there is a linear shift between the BD descriptor's rate field and the wcn36xx driver's rate table (wcn_5ghz_rates). We have a special clause to populate status.band for hardware scan offload frames. However, this block occurs after status.rate is already populated. Correctly handle this dependency by moving the band block before the rate block. This patch addresses kernel warnings & missing scan results for 5GHz APs that send their beacons/probe responses at the higher four legacy rates (24-54 Mbps), when using hardware scan offload: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 0 at net/mac80211/rx.c:4532 ieee80211_rx_napi+0x744/0x8d8 Modules linked in: wcn36xx [...] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 4.19.107-g73909fa #1 Hardware name: Square, Inc. T2 (all variants) (DT) Call trace: dump_backtrace+0x0/0x148 show_stack+0x14/0x1c dump_stack+0xb8/0xf0 __warn+0x2ac/0x2d8 warn_slowpath_null+0x44/0x54 ieee80211_rx_napi+0x744/0x8d8 ieee80211_tasklet_handler+0xa4/0xe0 tasklet_action_common+0xe0/0x118 tasklet_action+0x20/0x28 __do_softirq+0x108/0x1ec irq_exit+0xd4/0xd8 __handle_domain_irq+0x84/0xbc gic_handle_irq+0x4c/0xb8 el1_irq+0xe8/0x190 lpm_cpuidle_enter+0x220/0x260 cpuidle_enter_state+0x114/0x1c0 cpuidle_enter+0x34/0x48 do_idle+0x150/0x268 cpu_startup_entry+0x20/0x24 rest_init+0xd4/0xe0 start_kernel+0x398/0x430 ---[ end trace ae28cb759352b403 ]--- Fixes: 8a27ca394782 ("wcn36xx: Correct band/freq reporting on RX") Signed-off-by: Benjamin Li <benl@squareup.com> Tested-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211104010548.1107405-2-benl@squareup.com
2021-11-08wcn36xx: Put DXE block into reset before freeing memoryBryan O'Donoghue1-0/+6
When deiniting the DXE hardware we should reset the block to ensure there is no spurious DMA write transaction from the downstream WCNSS to upstream MSM at a skbuff address we will have released. Fixes: 8e84c2582169 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware") Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211105122152.1580542-4-bryan.odonoghue@linaro.org
2021-11-08wcn36xx: Release DMA channel descriptor allocationsBryan O'Donoghue1-0/+5
When unloading the driver we are not releasing the DMA descriptors which we previously allocated. Fixes: 8e84c2582169 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware") Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211105122152.1580542-3-bryan.odonoghue@linaro.org
2021-11-08wcn36xx: Fix DMA channel enable/disable cycleBryan O'Donoghue1-11/+27
Right now we have a broken sequence where we enable DMA channel interrupts which can be left enabled and never disabled if we hit an error path. Worse still when we unload the driver, the DMA channel interrupt bits are left intact. About the only saving grace here is that we do remember to disable the wcnss interrupt when unload the driver. Fixes: 8e84c2582169 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware") Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211105122152.1580542-2-bryan.odonoghue@linaro.org
2021-11-02Merge tag 'net-next-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-nextLinus Torvalds67-2814/+5507
Pull networking updates from Jakub Kicinski: "Core: - Remove socket skb caches - Add a SO_RESERVE_MEM socket op to forward allocate buffer space and avoid memory accounting overhead on each message sent - Introduce managed neighbor entries - added by control plane and resolved by the kernel for use in acceleration paths (BPF / XDP right now, HW offload users will benefit as well) - Make neighbor eviction on link down controllable by userspace to work around WiFi networks with bad roaming implementations - vrf: Rework interaction with netfilter/conntrack - fq_codel: implement L4S style ce_threshold_ect1 marking - sch: Eliminate unnecessary RCU waits in mini_qdisc_pair_swap() BPF: - Add support for new btf kind BTF_KIND_TAG, arbitrary type tagging as implemented in LLVM14 - Introduce bpf_get_branch_snapshot() to capture Last Branch Records - Implement variadic trace_printk helper - Add a new Bloomfilter map type - Track <8-byte scalar spill and refill - Access hw timestamp through BPF's __sk_buff - Disallow unprivileged BPF by default - Document BPF licensing Netfilter: - Introduce egress hook for looking at raw outgoing packets - Allow matching on and modifying inner headers / payload data - Add NFT_META_IFTYPE to match on the interface type either from ingress or egress Protocols: - Multi-Path TCP: - increase default max additional subflows to 2 - rework forward memory allocation - add getsockopts: MPTCP_INFO, MPTCP_TCPINFO, MPTCP_SUBFLOW_ADDRS - MCTP flow support allowing lower layer drivers to configure msg muxing as needed - Automatic Multicast Tunneling (AMT) driver based on RFC7450 - HSR support the redbox supervision frames (IEC-62439-3:2018) - Support for the ip6ip6 encapsulation of IOAM - Netlink interface for CAN-FD's Transmitter Delay Compensation - Support SMC-Rv2 eliminating the current same-subnet restriction, by exploiting the UDP encapsulation feature of RoCE adapters - TLS: add SM4 GCM/CCM crypto support - Bluetooth: initial support for link quality and audio/codec offload Driver APIs: - Add a batched interface for RX buffer allocation in AF_XDP buffer pool - ethtool: Add ability to control transceiver modules' power mode - phy: Introduce supported interfaces bitmap to express MAC capabilities and simplify PHY code - Drop rtnl_lock from DSA .port_fdb_{add,del} callbacks New drivers: - WiFi driver for Realtek 8852AE 802.11ax devices (rtw89) - Ethernet driver for ASIX AX88796C SPI device (x88796c) Drivers: - Broadcom PHYs - support 72165, 7712 16nm PHYs - support IDDQ-SR for additional power savings - PHY support for QCA8081, QCA9561 PHYs - NXP DPAA2: support for IRQ coalescing - NXP Ethernet (enetc): support for software TCP segmentation - Renesas Ethernet (ravb) - support DMAC and EMAC blocks of Gigabit-capable IP found on RZ/G2L SoC - Intel 100G Ethernet - support for eswitch offload of TC/OvS flow API, including offload of GRE, VxLAN, Geneve tunneling - support application device queues - ability to assign Rx and Tx queues to application threads - PTP and PPS (pulse-per-second) extensions - Broadcom Ethernet (bnxt) - devlink health reporting and device reload extensions - Mellanox Ethernet (mlx5) - offload macvlan interfaces - support HW offload of TC rules involving OVS internal ports - support HW-GRO and header/data split - support application device queues - Marvell OcteonTx2: - add XDP support for PF - add PTP support for VF - Qualcomm Ethernet switch (qca8k): support for QCA8328 - Realtek Ethernet DSA switch (rtl8366rb) - support bridge offload - support STP, fast aging, disabling address learning - support for Realtek RTL8365MB-VC, a 4+1 port 10M/100M/1GE switch - Mellanox Ethernet/IB switch (mlxsw) - multi-level qdisc hierarchy offload (e.g. RED, prio and shaping) - offload root TBF qdisc as port shaper - support multiple routing interface MAC address prefixes - support for IP-in-IP with IPv6 underlay - MediaTek WiFi (mt76) - mt7921 - ASPM, 6GHz, SDIO and testmode support - mt7915 - LED and TWT support - Qualcomm WiFi (ath11k) - include channel rx and tx time in survey dump statistics - support for 80P80 and 160 MHz bandwidths - support channel 2 in 6 GHz band - spectral scan support for QCN9074 - support for rx decapsulation offload (data frames in 802.3 format) - Qualcomm phone SoC WiFi (wcn36xx) - enable Idle Mode Power Save (IMPS) to reduce power consumption during idle - Bluetooth driver support for MediaTek MT7922 and MT7921 - Enable support for AOSP Bluetooth extension in Qualcomm WCN399x and Realtek 8822C/8852A - Microsoft vNIC driver (mana) - support hibernation and kexec - Google vNIC driver (gve) - support for jumbo frames - implement Rx page reuse Refactor: - Make all writes to netdev->dev_addr go thru helpers, so that we can add this address to the address rbtree and handle the updates - Various TCP cleanups and optimizations including improvements to CPU cache use - Simplify the gnet_stats, Qdisc stats' handling and remove qdisc->running sequence counter - Driver changes and API updates to address devlink locking deficiencies" * tag 'net-next-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2122 commits) Revert "net: avoid double accounting for pure zerocopy skbs" selftests: net: add arp_ndisc_evict_nocarrier net: ndisc: introduce ndisc_evict_nocarrier sysctl parameter net: arp: introduce arp_evict_nocarrier sysctl parameter libbpf: Deprecate AF_XDP support kbuild: Unify options for BTF generation for vmlinux and modules selftests/bpf: Add a testcase for 64-bit bounds propagation issue. bpf: Fix propagation of signed bounds from 64-bit min/max into 32-bit. bpf: Fix propagation of bounds from 64-bit min/max into 32-bit and var_off. net: vmxnet3: remove multiple false checks in vmxnet3_ethtool.c net: avoid double accounting for pure zerocopy skbs tcp: rename sk_wmem_free_skb netdevsim: fix uninit value in nsim_drv_configure_vfs() selftests/bpf: Fix also no-alu32 strobemeta selftest bpf: Add missing map_delete_elem method to bloom filter map selftests/bpf: Add bloom map success test for userspace calls bpf: Add alignment padding for "map_extra" + consolidate holes bpf: Bloom filter map naming fixups selftests/bpf: Add test cases for struct_ops prog bpf: Add dummy BPF STRUCT_OPS for test purpose ...
2021-11-01Merge tag 'overflow-v5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linuxLinus Torvalds2-7/+10
Pull overflow updates from Kees Cook: "The end goal of the current buffer overflow detection work[0] is to gain full compile-time and run-time coverage of all detectable buffer overflows seen via array indexing or memcpy(), memmove(), and memset(). The str*() family of functions already have full coverage. While much of the work for these changes have been on-going for many releases (i.e. 0-element and 1-element array replacements, as well as avoiding false positives and fixing discovered overflows[1]), this series contains the foundational elements of several related buffer overflow detection improvements by providing new common helpers and FORTIFY_SOURCE changes needed to gain the introspection required for compiler visibility into array sizes. Also included are a handful of already Acked instances using the helpers (or related clean-ups), with many more waiting at the ready to be taken via subsystem-specific trees[2]. The new helpers are: - struct_group() for gaining struct member range introspection - memset_after() and memset_startat() for clearing to the end of structures - DECLARE_FLEX_ARRAY() for using flex arrays in unions or alone in structs Also included is the beginning of the refactoring of FORTIFY_SOURCE to support memcpy() introspection, fix missing and regressed coverage under GCC, and to prepare to fix the currently broken Clang support. Finishing this work is part of the larger series[0], but depends on all the false positives and buffer overflow bug fixes to have landed already and those that depend on this series to land. As part of the FORTIFY_SOURCE refactoring, a set of both a compile-time and run-time tests are added for FORTIFY_SOURCE and the mem*()-family functions respectively. The compile time tests have found a legitimate (though corner-case) bug[6] already. Please note that the appearance of "panic" and "BUG" in the FORTIFY_SOURCE refactoring are the result of relocating existing code, and no new use of those code-paths are expected nor desired. Finally, there are two tree-wide conversions for 0-element arrays and flexible array unions to gain sane compiler introspection coverage that result in no known object code differences. After this series (and the changes that have now landed via netdev and usb), we are very close to finally being able to build with -Warray-bounds and -Wzero-length-bounds. However, due corner cases in GCC[3] and Clang[4], I have not included the last two patches that turn on these options, as I don't want to introduce any known warnings to the build. Hopefully these can be solved soon" Link: https://lore.kernel.org/lkml/20210818060533.3569517-1-keescook@chromium.org/ [0] Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/log/?qt=grep&q=FORTIFY_SOURCE [1] Link: https://lore.kernel.org/lkml/202108220107.3E26FE6C9C@keescook/ [2] Link: https://lore.kernel.org/lkml/3ab153ec-2798-da4c-f7b1-81b0ac8b0c5b@roeck-us.net/ [3] Link: https://bugs.llvm.org/show_bug.cgi?id=51682 [4] Link: https://lore.kernel.org/lkml/202109051257.29B29745C0@keescook/ [5] Link: https://lore.kernel.org/lkml/20211020200039.170424-1-keescook@chromium.org/ [6] * tag 'overflow-v5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (30 commits) fortify: strlen: Avoid shadowing previous locals compiler-gcc.h: Define __SANITIZE_ADDRESS__ under hwaddress sanitizer treewide: Replace 0-element memcpy() destinations with flexible arrays treewide: Replace open-coded flex arrays in unions stddef: Introduce DECLARE_FLEX_ARRAY() helper btrfs: Use memset_startat() to clear end of struct string.h: Introduce memset_startat() for wiping trailing members and padding xfrm: Use memset_after() to clear padding string.h: Introduce memset_after() for wiping trailing members/padding lib: Introduce CONFIG_MEMCPY_KUNIT_TEST fortify: Add compile-time FORTIFY_SOURCE tests fortify: Allow strlen() and strnlen() to pass compile-time known lengths fortify: Prepare to improve strnlen() and strlen() warnings fortify: Fix dropped strcpy() compile-time write overflow check fortify: Explicitly disable Clang support fortify: Move remaining fortify helpers into fortify-string.h lib/string: Move helper functions out of string.c compiler_types.h: Remove __compiletime_object_size() cm4000_cs: Use struct_group() to zero struct cm4000_dev region can: flexcan: Use struct_group() to zero struct flexcan_regs regions ...
2021-11-01ath9k: use swap() to make code cleanerYang Guang1-9/+5
Using swap() make it more readable. Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: Yang Guang <yang.guang5@zte.com.cn> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211028010451.7754-1-yang.guang5@zte.com.cn
2021-11-01wcn36xx: Indicate beacon not connection loss on MISSED_BEACON_INDBryan O'Donoghue1-2/+2
Firmware can trigger a missed beacon indication, this is not the same as a lost signal. Flag to Linux the missed beacon and let the WiFi stack decide for itself if the link is up or down by sending its own probe to determine this. We should only be signalling the link is lost when the firmware indicates Fixes: 8e84c2582169 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware") Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211027232529.657764-1-bryan.odonoghue@linaro.org
2021-11-01wcn36xx: ensure pairing of init_scan/finish_scan and start_scan/end_scanBenjamin Li3-7/+32
An SMD capture from the downstream prima driver on WCN3680B shows the following command sequence for connected scans: - init_scan_req - start_scan_req, channel 1 - end_scan_req, channel 1 - start_scan_req, channel 2 - ... - end_scan_req, channel 3 - finish_scan_req - init_scan_req - start_scan_req, channel 4 - ... - end_scan_req, channel 6 - finish_scan_req - ... - end_scan_req, channel 165 - finish_scan_req Upstream currently never calls wcn36xx_smd_end_scan, and in some cases[1] still sends finish_scan_req twice in a row or before init_scan_req. A typical connected scan looks like this: - init_scan_req - start_scan_req, channel 1 - finish_scan_req - init_scan_req - start_scan_req, channel 2 - ... - start_scan_req, channel 165 - finish_scan_req - finish_scan_req This patch cleans up scanning so that init/finish and start/end are always paired together and correctly nested. - init_scan_req - start_scan_req, channel 1 - end_scan_req, channel 1 - finish_scan_req - init_scan_req - start_scan_req, channel 2 - end_scan_req, channel 2 - ... - start_scan_req, channel 165 - end_scan_req, channel 165 - finish_scan_req Note that upstream will not do batching of 3 active-probe scans before returning to the operating channel, and this patch does not change that. To match downstream in this aspect, adjust IEEE80211_PROBE_DELAY and/or the 125ms max off-channel time in ieee80211_scan_state_decision. [1]: commit d195d7aac09b ("wcn36xx: Ensure finish scan is not requested before start scan") addressed one case of finish_scan_req being sent without a preceding init_scan_req (the case of the operating channel coinciding with the first scan channel); two other cases are: 1) if SW scan is started and aborted immediately, without scanning any channels, we send a finish_scan_req without ever sending init_scan_req, and 2) as SW scan logic always returns us to the operating channel before calling wcn36xx_sw_scan_complete, finish_scan_req is always sent twice at the end of a SW scan Fixes: 8e84c2582169 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware") Signed-off-by: Benjamin Li <benl@squareup.com> Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211027170306.555535-4-benl@squareup.com
2021-11-01wcn36xx: implement flush op to speed up connected scanBenjamin Li3-0/+59
Without ieee80211_ops->flush implemented to empty HW queues, mac80211 will do a 100ms dead wait after stopping SW queues, before leaving the operating channel to resume a software connected scan[1]. (see ieee80211_scan_state_resume) This wait is correctly included in the calculation for whether or not we've exceeded max off-channel time, as it occurs after sending the null frame with PS bit set. Thus, with 125 ms max off-channel time we only have 25 ms of scan time, which technically isn't even enough to scan one channel (although mac80211 always scans at least one channel per off- channel window). Moreover, for passive probes we end up spending at least 100 ms + 111 ms (IEEE80211_PASSIVE_CHANNEL_TIME) "off-channel"[2], which exceeds the listen interval of 200 ms that we provide in our association request frame. That's technically out-of-spec. [1]: Until recently, wcn36xx performed software (rather than FW-offloaded) scanning when 5GHz channels are requested. This apparent limitation is now resolved -- see commit 1395f8a6a4d5 ("wcn36xx: Enable hardware scan offload for 5Ghz band"). [2]: in quotes because about 100 ms of it is still on-channel but with PS set Signed-off-by: Benjamin Li <benl@squareup.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211027170306.555535-3-benl@squareup.com
2021-11-01wcn36xx: add debug prints for sw_scan start/completeBenjamin Li1-0/+4
Add some MAC debug prints for more easily demarcating a software scan when parsing logs. Signed-off-by: Benjamin Li <benl@squareup.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211027170306.555535-2-benl@squareup.com
2021-11-01ath10k: fetch (pre-)calibration data via nvmem subsystemChristian Lamparter2-2/+68
ATH10K chips are used it wide range of routers, accesspoints, range extenders, network appliances. On these embedded devices, calibration data is often stored on the main system's flash and was out of reach for the driver. To bridge this gap, ath10k is getting extended to pull the (pre-)calibration data through nvmem subsystem. To do this, a nvmem-cell containing the information can either be specified in the platform data or via device-tree. Tested with: Netgear EX6150v2 (IPQ4018 - pre-calibration method) TP-Link Archer C7 v2 (QCA9880v2 - old calibration method) Cc: Robert Marko <robimarko@gmail.com> Cc: Thibaut VARÈNE <hacks@slashdirt.org> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20211016234609.1568317-1-chunkeey@gmail.com
2021-11-01ath11k: set correct NL80211_FEATURE_DYNAMIC_SMPS for WCN6855Wen Gong3-1/+8
Commit 6f4d70308e5e ("ath11k: support SMPS configuration for 6 GHz") changed "if (ht_cap & WMI_HT_CAP_DYNAMIC_SMPS)" to "if (ht_cap & WMI_HT_CAP_DYNAMIC_SMPS || ar->supports_6ghz)" which means NL80211_FEATURE_DYNAMIC_SMPS is enabled for all chips which support 6 GHz. However, WCN6855 supports 6 GHz but it does not support feature NL80211_FEATURE_DYNAMIC_SMPS, and this can lead to MU-MIMO test failures for WCN6855. Disable NL80211_FEATURE_DYNAMIC_SMPS for WCN6855 since its ht_cap does not support WMI_HT_CAP_DYNAMIC_SMPS. Enable the feature only on QCN9074 as that's the only other device supporting 6 GHz band. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210914163726.38604-3-jouni@codeaurora.org
2021-10-28Merge ath-next from git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo21-100/+403
ath.git patches for v5.16. Major changes: ath11k * fix QCA6390 A-MSDU handling (CVE-2020-24588) wcn36xx * enable hardware scan offload for 5Ghz band * add missing 5GHz channels 136 and 144
Copyright © 1996 – 2026 Jason A. Donenfeld. All Rights Reverse Engineered.