| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Whenever i_coff of IQ calibration is too high, AR9565 drops max
rx rate to MCS4. Skipping IQ update at this time can avoid this
problem for AR9565.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
While resuming from S3, BT host issues HCI reset command and it
causes BT firmware to busy with security key calculation. At this
movement, WLAN detects MCI hardware error of MCI_CONT_INFO_TIMEOUT
and then it starts the recovery sequence repeatedly. Too many
recovery sequences would exhaust the BT kernel message pool. This
patch imposes a duration between consecutive BT recovery procedure.
Thus it solves BT firmware panic issue reported in AR9565.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
TXIQ and RXIQ share the same data path to upload the measurement
result, we should turn off RXIQ calibration while re-calibrating radio
Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Self generated MCI messages is configured to use chain 1. As
ar9565 is 1x1 solution, It can not use Chain 1. Hence fix
Chain 1 for ar9462 alone. Not doing so, could affect WLAN
connectivity in ar9565 as LNA sharing is not informed by BT.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The simulataneous transmission of both WLAN and BT might cause
increase in power levels. To avoid regulatory violation, WLAN tx
power will be adjusted according to BT power index based on avaliability
of BT scheduling messages. WLAN tx power reduction might affect its
performance. So WLAN tx power is only be lowered when the signal strength
is good enough. Otherwise concurrent tx will be disabled and WLAN uses
it default power levels. Also concurrent tx is disabled whenever WLAN is
moving to off-channel which might be used by BT.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
It is useful to have channel mode in caldata to find out
whether operaing channel is in HT40/20 when we are currently
on offchannel. It will be used by BTCOEX to enable/disable
concurrent tx mechanism later.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This feature enables both WLAN and BT can transmit simultaneously
by setting WLAN and BT to equal priorities. Whenever both are
transmitting, it might violate regulatory power limits. To avoid
regulatory violation, WLAN tx power will be adjusted according to BT
power index based on avaliability of BT scheduling message. If the
combined power exceeds threshold, BT transmission will be held off.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
WLAN updates channel bitmap when associated and disassociated. Channel
bitmap will reflect whare are the channels used or affected by WLAN and
BT should avoid using those. Not doing so, could affect BT traffic
as both WLAN and BT is operating on same channel.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Currently ath9k need to have beacon interval matched
between STA mode and beaconing mode. Advertize this
through interface combinations.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Once the driver advertizes interface combination logic
based on its firmware/hardware limitation, cfg80211
takes care of all the necessary logic such as maximum
beaconing vifs, standlone interface etc.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This will allow us to create virtual interface the driver supports.
Also this ensures multivif support and limitation advertised
by the driver is taken care in cfg80211 itself.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When WLAN is idle ensure we downgrade to FTP_STOMP_LOW weight
(from STOMP_LOW) to provide more bandwidth for BT FTP profile.
WLAN's idleness can be estimated by taking into account of the
rx data packets and just ignore beacons, qos nullfunc etc.
Also update bt_wait_time even if the chip is in NETWORK SLEEP
mode. This should help BT throughput when WLAN is idle.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Several people have complained about an unusual
and undocumented feature of the AR9170 hardware:
In siffer mode, the hardware generates spurious
ACK frames for every received frame... even
broadcasts.
The reason for this malfunction is unknown:
<http://marc.info/?l=linux-wireless&m=134517238506033>
But there's a workaround: Instead of the special
sniffer mode, the hardware will be put into
station mode and all rx filters are disabled.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Marco Fonseca <marco@tampabay.rr.com>
Reported-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
bf->bf_next is only while buffers are chained as part of an A-MPDU
in the tx queue. When a tid queue is flushed (e.g. on tearing down
an aggregation session), frames can be enqueued again as normal
transmission, without bf_next being cleared. This can lead to the
old pointer being dereferenced again later.
This patch might fix crashes and "Failed to stop TX DMA!" messages.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This reverts commit a240dc7b3c7463bd60cf0a9b2a90f52f78aae0fd.
This commit is reducing tx power by at least 10 db on some devices,
e.g. the Buffalo WZR-HP-G450H.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Cc: rmanohar@qca.qualcomm.com
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Roger says, Ubiquiti produce 2 versions of their WiFiStation USB adapter. One
has an internal antenna, the other has an external antenna and
name suffix EXT. They have separate USB ids and in distribution
openSUSE 12.2 (kernel 3.4.6), file /usr/share/usb.ids shows:
0cf3 Atheros Communications, Inc.
...
b002 Ubiquiti WiFiStation 802.11n [Atheros AR9271]
b003 Ubiquiti WiFiStationEXT 802.11n [Atheros AR9271]
Add b002 Ubiquiti WiFiStation in the PID/VID list.
Reported-by: Roger Price <ath9k@rogerprice.org>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Make use of SDIO CRC error workaround hardware flag and avoid
target revision checks.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
AR6004(UB134) firmware supports only LP Endpoint, So map
all Access Categories to Low Priority endpoints. This fixes a WPA2
connection issue as the uplink(tx) endpoint is appropriately
mapped in sync with the firmware.
Tested-by: Ben Gray <ben.r.gray@gmail.com>
Reported-by: Ben Gray <ben.r.gray@gmail.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Currently AR6004 handles the inactivity timeout resolution
in minutes rather than seconds. So parse the inactivity timeout
to the firmware in minutes. For now we will cleanup the
inactive station entries to the nearest converted minutes
(ex: an inactive time of 70 seconds would take atleast 2 - 3 minutes)
Tested with surprise removal of client cards/host shutdown.
Cc: Manikandan Radhakrishnan <mradhakr@qca.qualcomm.com>
Reported-by: Leela Kella <leela@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Rename ATH6KL_HW_FLAG_64BIT_RATES to ATH6KL_HW_64BIT_RATES.
This seemed to be necessary to add/use new hardware flags
without exceeding 80 lines. We shall be adding new hw flags
dropping the FLAG term.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Incase the resource allocation for the struct ath6kl_urb_context in the
function ath6kl_usb_alloc_pipe_resources fails, return this error
case so that ath6kl_usb_probe is aware of this error case.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
These checks are no longer needed as the necessary
USB support is already present in the driver.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Endpoint ID is checked to make sure it is valid.
Signed-off-by: Pandiyarajan Pitchaimuthu <c_ppitch@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The variable assigned_ep can be assigned value of -1 and is never
checked if it equals -1. So the endpoint array can have -1 as the index
value and can be out of bounds.
The value of assigned_ep is checked for -1 and is ensured that the
endpoint array doesn't go out of bounds.
Signed-off-by: Pandiyarajan Pitchaimuthu <c_ppitch@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
When a station tries to connect to an AP and if the MAC of the
station is in the AP's block list, the station cannot connect to the
AP. This is notified to the userspace with event
NL80211_CMD_CONN_FAILED and attribute NL80211_ATTR_CONN_FAILED_REASON.
The reason sent will be NL80211_CONN_FAIL_BLOCKED_CLIENT.
Signed-off-by: Pandiyarajan Pitchaimuthu <c_ppitch@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
When a station requests connection to an AP, that has already been
connected to the maximum number of stations it can support, an event
is sent to user space via NL80211_CMD_CONN_FAILED command and reason
attribute NL80211_ATTR_CONN_FAILED_REASON with
NL80211_CONN_FAIL_MAX_CLIENTS as reason.
Signed-off-by: Pandiyarajan Pitchaimuthu <c_ppitch@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The skb->tail pointer of rx buffers is not adjusted
after skb->data pointer is aligned to 4-byte, this
causes random rx data corruption.
Signed-off-by: Jin Navy <nhjin@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
It's safe to check endpoint id values before it get
really used. Found this on code review.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
There are 28 items defined in rate table array 'wmi_rate_tbl'.
The rate table index (reply->rate_index) in ath6kl_wmi_bitrate_reply_rx()
func is not checked for the valid max limit index before accessing
rate table array. There may be some incidents to get memory crashes
without safe max check. Fix this.
Found this on code review.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Return value of ath6kl_get_regpair() is stored in 'regpair' in
ath6kl_wmi_regdomain_event() func and it's directly accessed
in the debug prints without checking for NULL value. There are
situation to get NULL pointer as a return value from
ath6kl_get_regpair() func. Fix this.
Found this on code review.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Disallowing any wmi commands while re-initializing the
firmware results in connection failures after recovery
is done in open/WEP mode. To fix this, clear WMI_READY,
to make sure no wmi command is tried while fw is down.
Remove ATH6KL_STATE_RECOVERY state check in ath6kl_control_tx()
so that any configuration during fw init time will go through
using wmi commands.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Using list_move_tail() instead of list_del() + list_add_tail().
spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
gcc 4.8 warns
/backup/lsrc/git/linux-lto-2.6/drivers/net/wireless/ath/ath6kl/sdio.c:
In function 'ath6kl_sdio_enable_scatter':
/backup/lsrc/git/linux-lto-2.6/drivers/net/wireless/ath/ath6kl/sdio.c:748:16:
warning: 'ret' may be used uninitialized in this function
[-Wmaybe-uninitialized]
if (virt_scat || ret) {
^
The variable can indeed be uninitialized when the previous if branch is
skipped. I just set it to zero for now. I'm not fully sure the fix is
correct, maybe the || should be an && ?
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add a modparam to configure recovery. Recovery
from firmware error is disabled by default to debug
the actual issue further. To recovery from error,
modprobe ath6kl_core recovery_enable=1.
Reported-by: Jin Navy <nhjin@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add a bit in ath6kl_dev_state to maintian the run time state
of firmware recovery configuration. This would help to have
user configuration in fw_recovery which will be added in
a separate patch.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Checking for recovery state just before re-arming hb_timer is not
necessary, this should be done at the begining of the timer instead.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
hb_timer should be scheduled only when hb_poll is non-zero.
But in ath6kl_recovery_work() the timer is scheduled based
on fw_recovery.enable instead which is wrong.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
In some error conditions, fw pauses HTC pipes which would
result in control endpoint full condition. When we hit this
case, most of the time the device will be unusable. Re-initialize
the target to recover from this situation.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This patch adds support to detect fw error condition by sending
periodic message (heart beat challenge) to firmware. Upon reception
of the message, fw would send a response event to driver. When
there are no reponses from fw for about 5 cmd driver would
trigger the recovery logic assuming that fw has gone into an
error state.
Capable fw will advertise this capability through
ATH6KL_FW_CAPABILITY_HEART_BEAT_POLL bit. This feature
is disabled by default, can be enabled through a modparam
(heart_beat_poll). This modparam also confiures the polling
interval in msecs.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Re-initialize the target when fw crash is reported.
This would make the device functional again after
target crash. During the target re-initialization
it is made sure that target is not bugged with data/cmd
request, ar->state ATH6KL_STATE_RECOVERY is used
for this purpose.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
So that these functions will be used to re-initialize the fw
upon detecting fw error. This refactoring moves ar->state
setting out of core stop/start functionality.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The MSB of rate index from FW is used for sgi. But the ath6kl_wmi_get_rate
doesn't handle it. The access to wmi_rate_tbl array may be out of range
if sgi is 1. This may cause the return value of ath6kl_wmi_get_rate()
function is incorrect link rate. We add sgi adjustment to avoid such case.
kvalo: change patch title
Signed-off-by: Dengke Qiu <dqiu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
a minor cleanup in assigning the driver specific network type
based on interface type.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Since WOW_MASK_SIZE and WOW_PATTERN_SIZE have the same value, are
logically equivalent, and part of the WMI API so therefore unlikely to
change, consolidate these into WOW_PATTERN_SIZE.
Reported-by Kalle Valo <kvalo@qualcomm.com>
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
Rajkumar Manoharan
Bala Shanmugam
Mohammed Shafi Shajakhan
Christian Lamparter
Felix Fietkau
Pandiyarajan Pitchaimuthu
Vasanthakumar Thiagarajan
Raja Mani
Wei Yongjun
Andi Kleen
Dengke Qiu
Thomas Pedersen