aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/ath
AgeCommit message (Collapse)AuthorFilesLines
2012-03-15ath9k_hw: remove ath9k_hw_gettxintrtxqsFelix Fietkau3-11/+2
The driver can just check the mask directly Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k: optimize register access functionsFelix Fietkau2-4/+4
By checking for NR_CPUS, the compiler can optimize out register access serialization code on non-SMP kernels Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k_hw: remove ath9k_hw_getdefantennaFelix Fietkau3-8/+0
The default antenna (as programmed by the INI file) is always 0 anyway. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k_hw: remove ath9k_hw_htc_resetinitFelix Fietkau3-10/+2
Automatically set the ah->htc_reset_init on init and after PHY disable. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k_hw: clean up tx completion interrupt handlingFelix Fietkau3-8/+5
TXQ_FLAG_TXOKINT_ENABLE and TXQ_FLAG_TXERRINT_ENABLE are always set and used together, and they share the same bitmask in enum ath9k_tx_queue_flags. Simplify the code that tests for these flags. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k_hw: simplify tx queue interrupt mask handlingFelix Fietkau1-15/+11
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k: Fix multi-VIF BSS handlingSujith Manoharan5-34/+14
mac80211 provides short preamble information and ERP protection information on a per-BSS basis, which can be used. Remove flags stored in the driver, which was incorrect since they were being used in a global manner. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k: Remove aggregation flagsSujith Manoharan5-46/+29
SC_OP_TXAGGR and SC_OP_RXAGGR are not really needed. The HT capabilities of the station and HW can be used instead. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k_hw: Cleanup FastChannelChangeSujith Manoharan3-36/+74
The logic to determine whether to use FCC is a bit convoluted. Use a small helper function to decide whether FCC is to be used. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k: Remove 'other' VIF countSujith Manoharan3-4/+2
It is not needed and will not be used anyway since unsupported interfaces are not allowed to be created. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k: Remove unused variablesSujith Manoharan2-6/+0
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-15ath9k: Remove unnecessary initializationSujith Manoharan1-3/+0
There is no need to mask out SWBA/BMISS from the interrupt mask in start(). Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-13Merge branch 'for-linville' of git://github.com/kvalo/ath6klJohn W. Linville25-667/+1228
2012-03-13ath6kl: fix debug.c file modeKalle Valo1-0/+0
Commit 7504a3e1 ("ath6kl: add padding to firmware log records") accidentally changed debug.c mode from 100644 to 100755. Revert that back to original. Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-03-13ath6kl: use max_t() in ath6kl_cfg80211_connect()Kalle Valo1-2/+2
ath6kl/cfg80211.c:589: WARNING: max() should probably be max_t(u16, vif->listen_intvl_t, ATH6KL_MAX_WOW_LISTEN_INTL) Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-03-13ath6kl: fix open parenthesis alignment in ath6kl_sdio_suspend()Kalle Valo1-4/+5
ath6kl/sdio.c:875: CHECK: Alignment should match open parenthesis Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-03-13ath6kl: replace strict_strtoul() with kstrtoul()Kalle Valo1-17/+2
Recommended by checkpatch. Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-03-13ath6kl: fix regression in ath6kl_upload_board_file()Kalle Valo1-1/+2
My patch 24fc32b3 ("ath6kl: add ath6kl_bmi_write_hi32()") caused a regression in ath6kl_upload_board_file() and the board_address variable was not properly initialised in some cases: ath6kl/init.c:1068:6: warning: ‘board_address’ may be used uninitialized in this function Most likely this broke ar6004 support but I can't test that right now. Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-03-12ath9k: fix going to full-sleep on PS idleFelix Fietkau1-3/+5
The check for PS_WAIT_FOR_TX_ACK was inverted, the hardware should only go to full sleep if no tx is pending. Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@vger.kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-12ath9k: Fix mactime from being clobbered in rx_statusAshok Nagarajan1-2/+2
mactime was being overwritten by the function ath9k_rx_skb_preprocess. Fixed by memsetting rx_status in ath_rx_tasklet. Signed-off-by: Ashok Nagarajan <ashok@cozybit.com> Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-12ath9k: configure bss info at assoc notificationRajkumar Manoharan1-1/+1
The proper place to configure bss info is at assoc notification. So that ath9k continues to work if the supirous bssid notification will be removed in future. Cc: Johannes Berg <johannes@sipsolutions.net> Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-12ath9k_hw: Fix enabling of MCI and RTTMohammed Shafi Shajakhan2-2/+12
tested in AR9462 Rev:2, both hardware capability flag are set Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-12ath9k: Add wiphy name to log messages.Ben Greear2-17/+18
On systems with multiple NICs, it's nice to know which one is producing warnings. Here is an example of the new ouput: ath: wiphy0: Failed to stop TX DMA, queues=0x005! Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-12ath9k: Fix BTCOEX shutdownSujith Manoharan1-1/+2
Flush MCI profiles only if MCI is being actually used. This fixes a panic on driver unload when non-MCI devices are being used and btcoex_enable is set. BUG: unable to handle kernel NULL pointer dereference at (null) IP: [<ffffffffa06296d2>] ath_mci_flush_profile+0x12/0x100 [ath9k] Call Trace: [<ffffffffa061befe>] ath9k_stop_btcoex+0x5e/0x80 [ath9k] [<ffffffffa061ed57>] ath9k_stop+0xb7/0x230 [ath9k] [<ffffffffa0533f30>] ieee80211_stop_device+0x50/0x180 [mac80211] [<ffffffffa051f0cf>] ieee80211_do_stop+0x2af/0x6a0 [mac80211] [<ffffffffa051f4da>] ieee80211_stop+0x1a/0x20 [mac80211] [<ffffffff81365d96>] __dev_close_many+0x86/0xe0 [<ffffffff81365ee0>] dev_close_many+0xa0/0x110 [<ffffffff81366038>] rollback_registered_many+0xe8/0x260 [<ffffffff813661cb>] unregister_netdevice_many+0x1b/0x80 [<ffffffffa051e950>] ieee80211_remove_interfaces+0xd0/0x110 [mac80211] [<ffffffffa050c133>] ieee80211_unregister_hw+0x53/0x120 [mac80211] [<ffffffffa061d5a4>] ath9k_deinit_device+0x44/0x70 [ath9k] [<ffffffffa062c1d4>] ath_pci_remove+0x54/0xa0 [ath9k] [<ffffffff81267c46>] pci_device_remove+0x46/0x110 [<ffffffff8131021c>] __device_release_driver+0x7c/0xe0 [<ffffffff81310960>] driver_detach+0xd0/0xe0 [<ffffffff81310078>] bus_remove_driver+0x88/0xe0 [<ffffffff81311122>] driver_unregister+0x62/0xa0 [<ffffffff81268004>] pci_unregister_driver+0x44/0xc0 [<ffffffffa062c8b5>] ath_pci_exit+0x15/0x20 [ath9k] [<ffffffffa063205d>] ath9k_exit+0x15/0x31 [ath9k] [<ffffffff810b92cc>] sys_delete_module+0x18c/0x270 [<ffffffff814373dd>] ? retint_swapgs+0x13/0x1b [<ffffffff8124828e>] ? trace_hardirqs_on_thunk+0x3a/0x3f [<ffffffff81437de9>] system_call_fastpath+0x16/0x1b Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-12ath6kl: Fix merge error in ath6kl_set_ies()Aarthi Thiruvengadam1-22/+19
Portion of the commit id 080eec4fb4 ("ath6kl: Clear the IE in firmware if not set") was overwritten by mistake due to a merge conflict. This patch fixes the code back to how it should be. kvalo: more details to the commit log Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-03-09Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davemJohn W. Linville19-156/+122
2012-03-07ath9k: fix signal strength reporting issuesFelix Fietkau1-5/+7
On A-MPDU frames, the hardware only reports valid signal strength data for the last subframe. The driver also mangled rx_stats->rs_rssi using the ATH_EP_RND macro in a way that may make sense for ANI, but definitely not for reporting to mac80211. This patch changes the code to calculate the signal strength from the rssi directly instead of taking the average value, and flag everything but the last subframe in an A-MPDU to tell mac80211 to ignore the signal strength entirely, fixing signal strength fluctuation issues reported by various users. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-07ath9k: get rid of double queueing of rx frames on EDMAFelix Fietkau3-36/+28
Process rx status directly instead of separating the completion test from the actual rx status processing. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-07ath9k: remove rssi/antenna information from recv debug statsFelix Fietkau2-38/+0
The way this is implemented (simply storing the last value) is absolutely worthless for debugging anything, and the same information is also available through the MAC sample feature, so there's no point in keeping this around. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-07ath9k: make MAC sample statistics optionalFelix Fietkau4-6/+36
They're more expensive than some of the other debug options and only used in very rare situations, so it sometimes makes sense to disable them while leaving in debugfs support. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-07ath9k_hw: use cold instead of warm reset on AR9280Felix Fietkau1-4/+10
Cold reset is more reliable for getting the hardware out of some specific stuck states. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-07ath6kl: make ath6kl_bmi_[read|write]_hi32() endian safeKalle Valo1-3/+10
ath6kl_bmi_[read|write]_hi32() did not have endian support, fix that. Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-03-07ath6kl: fix too long linesKalle Valo3-26/+27
Found by checkpatch: drivers/net/wireless/ath/ath6kl/init.c:78: WARNING: line over 80 characters drivers/net/wireless/ath/ath6kl/init.c:397: WARNING: line over 80 characters drivers/net/wireless/ath/ath6kl/init.c:407: WARNING: line over 80 characters drivers/net/wireless/ath/ath6kl/htc.c:189: WARNING: line over 80 characters drivers/net/wireless/ath/ath6kl/htc.c:704: WARNING: line over 80 characters drivers/net/wireless/ath/ath6kl/htc.c:2452: WARNING: line over 80 characters Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-03-07ath6kl: document all spinlocksKalle Valo5-0/+36
Also fixes quite a few checkpatch warnings like this: ath6kl/hif.h:226: CHECK: spinlock_t definition without comment Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-03-07ath6kl: fix open paranthesis alignment in ath6kl_cfg80211_connect()Kalle Valo1-2/+8
ath6kl/cfg80211.c:462: CHECK: Alignment should match open parenthesis Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-03-07ath6kl: fix error handling ath6kl_target_config_wlan_params()Kalle Valo1-28/+38
The error handling in ath6kl_target_config_wlan_params() was just weird, fix that. This also fixes some of the open parenthesis alignment issues reported by checkpatch. Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-03-07ath6kl: add ath6kl_bmi_read_hi32()Kalle Valo2-16/+11
There are few 32 bit reads from the host interest area. Add ath6kl_bmi_read_hi32() to make it easier to do that. As code is cleaner this also fixes few checkpatch warnings. Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-03-07ath6kl: add ath6kl_bmi_write_hi32()Kalle Valo2-76/+32
We have a lot of 32 bit writes to the host interest area and the code doing that is ugly. Clean that up by adding ath6kl_bmi_write_hi32(). This also fixes few checkpatch warnings. Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-03-07ath6kl: remove multiple assignmentsKalle Valo1-4/+4
Found by checkpatch: drivers/net/wireless/ath/ath6kl/cfg80211.c:1295: CHECK: multiple assignments should be avoided drivers/net/wireless/ath/ath6kl/cfg80211.c:3000: CHECK: multiple assignments should be avoided Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-03-07ath6kl: logical continuations should be on the previous lineKalle Valo4-15/+16
All found by checkpatch: ath6kl/wmi.c:1036: CHECK: Logical continuations should be on the previous line Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-03-07ath6kl: alignment should match open parenthesisKalle Valo11-115/+115
Fix the issues which checkpatch found and were easy to fix. Especially callers of ath6kl_bmi_write() are tricky and that needs to be fixed separately. Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-03-07ath6kl: fix checkpatch error with EPSTAT() macroKalle Valo1-3/+7
ath6kl/debug.c:739: ERROR: Macros with complex values should be enclosed in parenthesis Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-03-07ath6kl: fix pointer styleKalle Valo1-2/+2
reported by checkpatch: ath6kl/core.h:748: ERROR: "foo * bar" should be "foo *bar" ath6kl/core.h:751: ERROR: "foo * bar" should be "foo *bar" Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-03-07ath6kl: Set optimal listen intvl,bmiss,scan params while going to wow suspendRaja Mani4-1/+90
* In order to save the target power in WOW suspend state, configure the best optimal values for the below parameters, - listen interval. - beacon miss interval. - scan parameters. Default values for above attributes are reverted in wow resume operation. * The default listen interval is set before the host issue connect request. * New function is added to configure beacon miss count. kvalo: minor changes to fix open parenthesis alignment Signed-off-by: Raja Mani <rmani@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-03-07ath6kl: Maintain the listen interval per VIF specificRaja Mani5-14/+16
Firmware has the option to support the listen interval per vif specific. Fix this. Listen interval can be set by the TUs or by the number of beacons. Current code enables the user to configure the listen interval in the unit of 'number of beacons' using debugfs entry "listen_interval". Going forward, we need to alter the listen interval in the unit of TUs to get good power numbers while going to WOW suspend/resume. Allowing the user to change the listen interval in the unit of "number of beacons" in debugfs and changing listen interval in wow suspend/resume in the unit of time (TUs) would lead us to confuse. This patch make sures the listen interval is changed only in the unit of time (TUs). Signed-off-by: Raja Mani <rmani@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-03-07ath6kl: Check wow state before sending control and data pktRaja Mani4-3/+44
Below two scenarios are taken care in this patch which helped to fix the firmware crash during wow suspend/resume. * TX operation (ctrl tx and data tx) has to be controlled based on suspend state. i.e, with respect to WOW mode, control packets are allowed to send from the host until the suspend state goes ATH6KL_STATE_WOW and the data packets are allowed until WOW suspend operation starts. * Similarly, wow resume is NOT allowed if WOW suspend is in progress. Signed-off-by: Raja Mani <rmani@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-03-07ath6kl: Add provision to define suspend policy in disconnected state.Raja Mani4-7/+24
It gives flexibility to the user to define suspend policy when the suspend mode is set to WOW and the device is in disconnected state at the time of suspend. New module parameter wow_mode is added to get the choice from the user. This parameter is valid only if the module parameter suspend_mode is set to WOW. To force WOW in connected state and cut power in disconnected state: suspend_mode=0x3 wow_mode=0x1 To force WOW in connected state and deep sleep in disconnected state (this is also the default wow_mode): suspend_mode=0x3 wow_mode=0x2 If there is no value specified to wow_mode during insmod, deep sleep mode will be tried in the disconnected state. kvalo: clarified commit log Signed-off-by: Raja Mani <rmani@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2012-03-06ath5k: do not re-run AGC calibration periodicallyFelix Fietkau1-24/+8
All other Atheros drivers run the AGC gain calibration and DC offset calibration only after reset. Running them periodically has caused stability issues on some (primarily AR2315/2413/5413/5414 based) devices, leading to messages such as: ath5k phy0: gain calibration timeout (2462MHz) ath5k phy0: calibration of channel 11 failed Related bug reports: https://dev.openwrt.org/ticket/10574 https://bugzilla.redhat.com/show_bug.cgi?id=795141 Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-06ath5k: do not stop queues for full calibrationFelix Fietkau1-12/+2
Some calibration types interfere with tx activity, but the queue stop does not prevent that. In fact, some calibration types need tx activity to properly function, so stopping the queues for them is counterproductive. In some tests this patch has been shown to improve stability, especially in AP or ad-hoc mode. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-03-06ath5k: allow AP and mesh mode to operate simultaneouslyChun-Yeow Yeoh3-2/+9
This patch allows the possibility of having the mesh point and AP to be operated simultaneously in one single radio. Previously, mesh point fails to generate the mesh beacon if virtual AP is created for the same radio. Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Copyright © 1996 – 2026 Jason A. Donenfeld. All Rights Reverse Engineered.