| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Same skb is being reused for storing command response from firmware
in PCIe chipsets. There was a bug while updating the skb length.
This patch ensures skb length correctly gets updated based on rx_len.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In corner case, we may end up processing same interrupt twice.
We have a logic to read pending interrupts at the end of interrupt
processing routine. It has a race with interrupts read in interrupt
handler. This patch solves the problem by ORing the interrupt bitmap
in this case.
The symptom for this bug is below messages in dmesg log.
[ 11.522123] mwifiex_pcie 0000:01:00.0: CMD_RESP: invalid cmd resp
[ 11.680412] mwifiex_pcie 0000:01:00.0: There is no command but got cmdrsp
Link: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
It's been observed that request_irq() failure leads to a system crash
due to a bug in mwifiex driver.
When this failure happens, mwifiex_add_card() already takes care of
clearing and freeing adapter->card pointer. This patch removes the
redundant cleanup code causing crash.
Signed-off-by: Karthik D A <karthida@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
memory is malloced in mwifiex_cfg80211_start_ap() and should be
freed before leaving from the error handling cases, otherwise it
will cause memory leak.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fixes the following sparse warning:
drivers/net/wireless/marvell/libertas/cfg.c:2047:5: warning:
symbol 'lbs_set_power_mgmt' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
For multiple REG Host Commands (e.g HostCmd_CMD_802_11_EEPROM_ACCESS,
HostCmd_CMD_MAC_REG_ACCESS etc.) "cpu_to_leX"-converted values are
saved to driver. So, "leX_to_cpu" conversion is required too many
times afterwards in driver.
This patch reduces the endian: conversion without saving "cpu_to_leX"
converted values in driver. This will convert endianness in prepare
command and command response path.
Signed-off-by: Prasun Maiti <prasunmaiti87@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Kalle Valo says:
====================
wireless-drivers-next patches for 4.8
Major changes:
iwlwifi
* more work on the RX path for the 9000 device series
* some more dynamic queue allocation work
* SAR BIOS implementation
* some work on debugging capabilities
* added support for GCMP encryption
* data path rework in preparation for new HW
* some cleanup to remove transport dependency on mac80211
* support for MSIx in preparation for new HW
* lots of work in preparation for HW support (9000 and a000 series)
mwifiex
* implement get_tx_power and get_antenna cfg80211 operation callbacks
wl18xx
* add support for 64bit clock
rtl8xxxu
* aggregation support (optional for now)
Also wireless-drivers is merged to fix some conflicts.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As interrupt is read in interrupt handler as well as interrupt processing
thread, we observed a corner case issue for MSI in which interrupt gets
processed twice.
This patch moves interrupt reading code for MSI mode from
mwifiex_interrupt_status() to mwifiex_pcie_process_int() to avoid the
issue.
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The PCIe driver didn't mask the host interrupts before trying to tear
down. This causes lockups at reboot or rmmod when using MSI-X on 8997,
since the MSI handler gets confused and locks up the system.
Also tested on 8897, which does not support MSI-X (and wasn't
experiencing this same bug). No regressions seen there.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
PCIe-USB8997 variant is being used in the product. Let's change default
firmware from PCIe-UART to PCIe-USB. So by default PCIe-USB firmware would
be downloaded if version register doesn't give any information.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The two members min_scan_time and max_scan_time of structure
"mwifiex_ie_types_btcoex_scan_time" are of two bytes each. The values
are assigned directtly from firmware without endian conversion handling.
So, wrong datas will get saved in big-endian systems.
This patch converts the values into cpu's byte order before assigning them
into the local members.
Signed-off-by: Prasun Maiti <prasunmaiti87@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
scan_block flag is used to block scan operation when 4 way handshake
is in progress. Sometimes it doesn't get cleared due to incomplete
association. An example is assoc request/response is done, but add key
operation get canceled in some corner cases. As a result, further
association/scan operations are blocked.
This patch fixes the problem by clearing scan_block flag.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch fixes below NULL pointer dereference observed in suspend
stress test. When scan is cancelled during system suspend, we may end
up aceesing "priv->scan_request" in corner case.
[ 3035.304682] BUG: KASAN: null-ptr-deref on address 0000000000000008
[ 3035.304704] Read of size 4 by task ksdioirqd/mmc2/1183
[ 3035.304744] CPU: 0 PID: 1183 Comm: ksdioirqd/mmc2 Tainted: G W 3.18.0 #1169
[ 3035.304772] Call trace:
[ 3035.304825] [<ffffffc00020a520>] dump_backtrace+0x0/0x190
[ 3035.304864] [<ffffffc00020a6cc>] show_stack+0x1c/0x28
[ 3035.304901] [<ffffffc000b36db8>] dump_stack+0xa0/0xf8
[ 3035.304940] [<ffffffc00039c494>] kasan_report+0x120/0x4fc
[ 3035.304975] [<ffffffc00039b6b4>] __asan_load4+0x20/0x80
[ 3035.305546] [<ffffffbffc1f5aec>] mwifiex_check_next_scan_command+0x1a4/0x588 [mwifiex]
[ 3035.306091] [<ffffffbffc1f7aec>] mwifiex_handle_event_ext_scan_report+0x304/0x370 [mwifiex]
[ 3035.306735] [<ffffffbffc206bb8>] mwifiex_process_sta_event+0x6c0/0xf10 [mwifiex]
[ 3035.307200] [<ffffffbffc1e609c>] mwifiex_process_event+0x2f4/0x358 [mwifiex]
[ 3035.307612] [<ffffffbffc1e25c8>] mwifiex_main_process+0x3cc/0x80c [mwifiex]
[ 3035.307737] [<ffffffbffc2523a0>] mwifiex_sdio_interrupt+0x198/0x1c0 [mwifiex_sdio]
[ 3035.307785] [<ffffffc0008d9250>] process_sdio_pending_irqs+0x15c/0x1d4
[ 3035.307826] [<ffffffc0008d93f0>] sdio_irq_thread+0xd8/0x288
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The flag should be cleaned along with other scan operation variables.
This was missing at some places.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We will derive sta_priv at the beginning of suspend handler.
This will be useful for next patch in this series.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Beacon report radio measurement requires reporting observed BSSs
on the channels specified in the beacon request. If the measurement
mode is set to passive or active, it requires actually performing a
scan (passive or active, accordingly), and reporting the time that
the scan was started and the time each beacon/probe was received
(both in terms of TSF of the BSS of the requesting AP). If the
request mode is table, this information is optional.
In addition, the radio measurement request specifies the channel
dwell time for the measurement.
In order to use scan for beacon report when the mode is active or
passive, add a parameter to scan request that specifies the
channel dwell time, and add scan start time and beacon received time
to scan results information.
Supporting beacon report is required for Multi Band Operation (MBO).
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Sometimes MSIx interrupts are received out of order on multi-core
system. This creates a problem when there is a race between data
packet and SLEEP event from firmware. We will disable MSIx interrupt
mode to solve the problem and go with MSI mode.
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since commit de3bb771f471 ("cfg80211: add more warnings for inconsistent
ops") the wireless core warns if a driver implements a cfg80211 callback
but doesn't implements the inverse operation.
The mwifiex driver defines a .set_antenna handler but not a .get_antenna
so this not only makes the core to print a warning when creating a new
wiphy but also the antenna isn't reported to user-space apps such as iw.
This patch queries the antenna to the firmware so is properly reported to
user-space. With this patch, the wireless core does not warn anymore and:
$ iw phy phy0 info | grep Antennas
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x3 RX 0x3
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
[javier: expand the commit message]
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The mwifiex driver implements a cfg80211 .set_tx_power operation handler
but doesn't have the inverse .get_tx_power callback.
This not only has the effect that the Tx power can't be reported to user
space tools such as iwconfig and iwlist but also that the wireless core
prints a warning when a new wiphy is created due an cfg80211 operation
being implemented without its counterpart.
After this patch, the Tx power is properly reported to user-space tools:
$ iwlist mlan0 txpower
mlan0 unknown transmit-power information.
Current Tx-Power=13 dBm (19 mW)
and also the following warning isn't shown anymore on the driver probe:
WARNING: CPU: 3 PID: 127 at net/wireless/core.c:366 wiphy_new_nm+0x66c/0x6ac
Modules linked in: mwifiex_sdio mwifiex
CPU: 3 PID: 127 Comm: kworker/3:1 Tainted: G W 4.7.0-rc1-next-20160531-00006-g569df5b983f3
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events request_firmware_work_func
[<c010e1ac>] (unwind_backtrace) from [<c010af38>] (show_stack+0x10/0x14)
[<c010af38>] (show_stack) from [<c0323b9c>] (dump_stack+0x88/0x9c)
[<c0323b9c>] (dump_stack) from [<c011a828>] (__warn+0xe8/0x100)
[<c011a828>] (__warn) from [<c011a8f0>] (warn_slowpath_null+0x20/0x28)
[<c011a8f0>] (warn_slowpath_null) from [<c06a42d4>] (wiphy_new_nm+0x66c/0x6ac)
[<c06a42d4>] (wiphy_new_nm) from [<bf1c24cc>] (mwifiex_register_cfg80211+0x28/0x3f0 [mwifiex])
[<bf1c24cc>] (mwifiex_register_cfg80211 [mwifiex]) from [<bf1a0018>] (mwifiex_fw_dpc+0x2b0/0x474 [mwifiex])
[<bf1a0018>] (mwifiex_fw_dpc [mwifiex]) from [<c040eb74>] (request_firmware_work_func+0x30/0x58)
[<c040eb74>] (request_firmware_work_func) from [<c012fe90>] (process_one_work+0x124/0x338)
[<c012fe90>] (process_one_work) from [<c01300dc>] (worker_thread+0x38/0x4d4)
[<c01300dc>] (worker_thread) from [<c01353b8>] (kthread+0xdc/0xf4)
[<c01353b8>] (kthread) from [<c0107978>] (ret_from_fork+0x14/0x3c)
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The commit 7311ea850079 ("mwifiex: fix AP start problem for newly added
interface") attempted to fix an issue when a new AP interface is added.
But the patch didn't check the return value of the functions doing the
firmware calls and returned an error even if the functions didn't fail.
This prevents the network device to be registered properly, so fix it.
Fixes: 7311ea850079 ("mwifiex: fix AP start problem for newly added interface")
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
It's been observed that if interface type is changed from managed to
__ap, AP can be successfully started. But there is a problem if new
ap interface is added.
The problem got resolved after sending appropriate commands to firmware
in add_interface handler.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch populates secondary channel offset and downloads it to
firmware to fix the problem.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
On some platforms, driver is unable to wakeup firmware after system resume
due to a problem at MMC subsystem. Triggering card reset in this case has
a race with card removal from MMC which causes system hang. This patch
resolves the problem by not triggering card reset.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
It is obeserved that sometimes scan operation will block the disconnect
during system suspend. It's ok to cancel ongoing scan in this case. It
reduces unnecessary system suspend delay.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch creates common function mwifiex_cancel_scan to remove
duplication of code.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When an association command is sent to firmware but the process is
killed before the command response arrives, driver will try to
access bss_desc which is already freed. This issue is fixed by
checking return value of bss_start.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
lbs_mac_event_disconnected may free priv->currenttxskb
while lbs_hard_start_xmit accesses to it.
The patch adds a spinlock for mutual exclusion.
Tested on OLPC XO-1 (usb8388) and XO-1.5 (sd8686) with v4.7-rc3.
Confirmed that lbs_mac_event_disconnected is being called on the
station when hostapd on access point is given SIGHUP.
Signed-off-by: Pavel <andrianov@ispras.ru>
Tested-by: James Cameron <quozl@laptop.org>
Acked-by: Vaishali Thakkar <vaishali.thakkar@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
alloc_workqueue replaces deprecated create_workqueue().
A dedicated workqueue has been used since the workitem (viz
&priv->cmd_work per priv, which maps to lbtf_cmd_work) is involved in
actual command processing and may be used on a memory reclaim path.
The workitems require forward progress under memory pressure and hence,
WQ_MEM_RECLAIM has been set. Since there are only a fixed number of work
items, explicit concurrency limit is unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Calling sdio_claim_host() from the interface independent part of
the mwifiex driver is not only a layering violation, but also causes
a link error if MMC support is disabled, or if CONFIG_MMC=m
and CONFIG_MWIFIEX=y:
drivers/net/built-in.o: In function `mwifiex_fw_dpc':
:(.text+0xff138): undefined reference to `sdio_claim_host'
:(.text+0xff158): undefined reference to `sdio_release_host'
The right way to do this is to have the sdio specific code in the
sdio driver front-end, and we already have a callback pointer that
we can use for this after exporting the generic fw download
function from the core driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 65c71efe1c59 ("mwifiex: fix racing condition when downloading firmware")
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
alloc_workqueue replaces deprecated create_workqueue().
In if_sdio.c, the workqueue card->workqueue has workitem
&card->packet_worker, which is mapped to if_sdio_host_to_card_worker.
The workitem is involved in sending packets to firmware.
Forward progress under memory pressure is a requirement here.
In if_spi.c, the workqueue card->workqueue has workitem
&card->packet_worker, which is mapped to if_spi_host_to_card_worker.
The workitem is involved in sending command packets from the host.
Forward progress under memory pressure is a requirement here.
Dedicated workqueues have been used in both cases since the workitems
on the workqueues are involved in normal device operation with
WQ_MEM_RECLAIM set to gurantee forward progress under memory pressure.
Since there are only a fixed number of work items, explicit concurrency
limit is unnecessary.
flush_workqueue is unnecessary since destroy_workqueue() itself calls
drain_workqueue() which flushes repeatedly till the workqueue
becomes empty. Hence the calls to flush_workqueue() before
destroy_workqueue() have been dropped.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
gcc-6 reports:
drivers/net/wireless/marvell/libertas_tf/main.c:30:19: error:
'lbtf_driver_version' defined but not used
with -Werror=unused-const-variable=.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> [0-day test robot]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt DT
binding document lists the possible compatible strings that a SDIO child
node can have, so the driver checks if the defined in the node matches.
But the error message when that's not the case is misleading, so change
for one that makes clear what the error really is. Also, returning a -1
as errno code is not correct since that's -EPERM. A -EINVAL seems to be
a more appropriate one.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt DT
binding document say that the "interrupts" property in the child node is
optional. So the property being missed shouldn't be treated as an error.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The function can fail so the returned value should be checked
and the error propagated to the caller in case of a failure.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
It's better to have the device name prefixed in the error message.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Instead of duplicating part of the cleanups needed in case of an error
in .probe callback, have a single error path and use goto labels as is
common practice in the kernel.
This also has the nice side effect that the cleanup operations are made
in the inverse order of their counterparts, which was not the case for
the mwifiex_add_card() error path.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
There's only a check if mwifiex_add_card() returned a nonzero value, but
the actual error code is neither stored nor propagated to the caller. So
instead of always returning -1 (which is -EPERM and not a suitable errno
code in this case), propagate the value returned by mwifiex_add_card().
Patch also removes the assignment of sdio_disable_func() returned value
since it was overwritten anyways and what matters is to know the error
value returned by the first function that failed.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
If the sdio_enable_func() function fails on .probe, the -EIO errno code
is always returned but that could make more difficult to debug and find
the cause of why the function actually failed.
Since the driver/device core prints the value returned by .probe in its
error message propagate what was returned by sdio_enable_func() at fail.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
SDIO is an auto enumerable bus so the SDIO devices are matched using the
sdio_device_id table and not using compatible strings from a OF id table.
However, commit ce4f6f0c353b ("mwifiex: add platform specific wakeup
interrupt support") allowed to match nodes defined as child of the SDIO
host controller in the probe function using a compatible string to setup
platform specific parameters in the DT.
The problem is that the OF parse function is always called regardless if
the SDIO dev has an OF node associated or not, and prints an error if it
is not found. So, on a platform that doesn't have a node for a SDIO dev,
the following misleading error message will be printed:
[ 12.480042] mwifiex_sdio mmc2:0001:1: sdio platform data not available
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch ensures that 'locally_generated' parameter is correctly
passed to cfg80211_disconnected() API.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The GFP_DMA flag is obviously misunderstood in the mwifiex driver. It's
meant for legacy ISA DMA memory mappings only -- the lower 16MB on x86.
That doesn't apply to PCIe or SDIO devices, I guess.
Remove the GFP_DMA flag to reduce the need to place the socket buffer
allocation into the low mem DMA area, which might already be in use by
other drivers.
This misuse was flagged by the PaX USERCOPY feature by chance, as it
detected the user copy operation from a DMA buffer in the recvfrom()
syscall path.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Tested-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Cc: Nishant Sarmukadam <nishants@marvell.com>
Cc: Xinming Hu <huxm@marvell.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Brad Spengler <spender@grsecurity.net>
Cc: PaX Team <pageexec@freemail.hu>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The action 'check for winner' and 'download firmware' should be an
atomic action. This is true for btmrvl driver but not mwmfiex, which
cause firmware download to fail when the following senerio happens:
1) mwifiex check winner status: true
2) btmrvl check winner status: true, and start downloading firmware
3) mwfieix tries to download firmware, but failed because btmrvl is
already downloading.
This won't happen if 1) and 3) is an atomic action. This patch adds
sdio_claim/release_host call around those two actions to make sure it's
atomic.
Signed-off-by: Wei-Ning Huang <wnhuang@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Do not dereference card before checking against NULL value.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Variable adapter is incorrectly initialized.
Fixes: bf00dc22bc7a ("mwifiex: AMSDU Rx frame handling in AP mode")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
firmare -> firmware
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Kalle Valo says:
====================
wireless-drivers patches for 4.7
Major changes:
iwlwifi
* remove IWLWIFI_DEBUG_EXPERIMENTAL_UCODE kconfig option
* work for RX multiqueue continues
* dynamic queue allocation work continues
* add Luca as maintainer
* a bunch of fixes and improvements all over
brcmfmac
* add 4356 sdio support
ath6kl
* add ability to set debug uart baud rate with a module parameter
wil6210
* add debugfs file to configure firmware led functionality
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use dev_err instead of pr_err and add newline character at the end.
Signed-off-by: Wei-Ning Huang <wnhuang@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This header file is only needed for drivers binding to a PCI bridge
device allocated by drivers/pci/pcie/portdrv_core.c. The mwifiex driver
doesn't do that nor use any symbols defined in pcieport_if.h.
Cc: Amitkumar Karwar <akarwar@marvell.com>
Cc: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
Wolfram Sang
Amitkumar Karwar
Karthik D A
Wei Yongjun
Prasun Maiti
David S. Miller
Shengzhen Li
Brian Norris
Avraham Stern
Javier Martinez Canillas
Xinming Hu
Ganapathi Bhat
Pavel Andrianov
Bhaktipriya Shridhar
Arnd Bergmann
Guenter Roeck
Mathias Krause
Wei-Ning Huang
Heinrich Schuchardt
Julia Lawall
Lukas Wunner