aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/mediatek
AgeCommit message (Collapse)AuthorFilesLines
2021-04-21mt76: mt7615: rely on pm refcounting in mt7615_led_set_configLorenzo Bianconi1-1/+3
Rely on mt76_connac_pm_ref/mt76_connac_pm_unref utility routines in mt7615_led_set_config Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: connac: alaways wake the device before scanningLorenzo Bianconi3-8/+8
move scanning check from mt76_connac_power_save_sched routine to mt7921_pm_power_save_work/mt7615_pm_power_save_work ones Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7921: get rid of useless MT76_STATE_PM in mt7921_mac_workLorenzo Bianconi1-5/+0
Remove useless MT76_STATE_PM check in mt7921_mac_work since mt7921_mutex_acquire will wake up the device if necessary Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: connac: remove MT76_STATE_PM in mac_tx_freeLorenzo Bianconi2-10/+0
Get rid of MT76_STATE_PM chec in mt7615_mac_tx_free and mt7921_mac_tx_free since we already rely on mt76_connac_pm_unref in the NAPI callback. Remove mt76_connac_power_save_sched calls in mt7615_mac_tx_free and mt7921_mac_tx_free Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: connac: check wake refcount in mcu_fw_pmctrlLorenzo Bianconi3-2/+14
In order to avoid synchronization races between tx and rx path, rely on mt76_connac_skip_fw_pmctrl putting the chip in sleep mode for mt7921 and mt7663 devices Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: connac: unschedule ps_work in mt76_connac_pm_wakeLorenzo Bianconi3-2/+1
In order to avoid synchronization issues between wake and ps works, cancel ps_work in mt76_connac_pm_wake routine Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7663: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx/rx napiLorenzo Bianconi2-6/+34
Introduce mt7615_poll_rx rx napi callback for mt7663. Do not access device registers in tx/rx napi if the device is not awake. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7921: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx/rx napiLorenzo Bianconi3-8/+37
Introduce mt7921_poll_rx rx napi callback for mt7921. Do not access device registers in tx/rx napi if the device is not awake. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: dma: add the capability to define a custom rx napi poll routineLorenzo Bianconi8-12/+14
Add the capability to define a custom rx napi callback for each driver. This is a preliminary patch to properly support runtime-pm on rx side Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7663: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx pathLorenzo Bianconi5-18/+25
Introduce mt7615_tx_worker routine as mt76 tx worker callback for mt7663. Rely on mt76_connac_pm_ref/mt76_connac_pm_unref to check PM state and increment/decrement wake counter Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7921: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx pathLorenzo Bianconi3-14/+13
Introduce mt7921_tx_worker routine as mt76 tx worker callback for mt7921. Rely on mt76_connac_pm_ref/mt76_connac_pm_unref to check PM state and increment/decrement wake counter Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: connac: introduce wake counter for fw_pmctrl synchronizationLorenzo Bianconi1-0/+31
Introduce wake counter and related spinlock in order to synchronize tx/rx path and fw_pmctrl request. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7663: fix a race between mt7615_mcu_drv_pmctrl and mt7615_mcu_fw_pmctrlLorenzo Bianconi2-6/+15
Introduce a mutex in order to avoid a race between mt7615_mcu_lp_drv_pmctrl and mt7615_mcu_fw_pmctrl routines since they are run two independent works Fixes: 1f549009b5b2 ("mt76: mt7615: do not request {driver,fw}_own if already granted") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7921: fix a race between mt7921_mcu_drv_pmctrl and mt7921_mcu_fw_pmctrlLorenzo Bianconi3-10/+26
Introduce a mutex in order to avoid a race between mt7921_mcu_drv_pmctrl and mt7921_mcu_fw_pmctrl routines since they are run two independent works Fixes: 1d8efc741df8 ("mt76: mt7921: introduce Runtime PM support") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7921: remove leftover function declarationLorenzo Bianconi1-2/+0
Get rid of leftover mt7921_mcu_add_bss_info routine declaration Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: connac: move mcu_update_arp_filter in mt76_connac moduleLorenzo Bianconi8-104/+58
Move mt76_connac_mcu_update_arp_filter in mt76_connac module since the code is shared between mt7615 and mt7921 Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7921: do not use 0 as NULL pointerLorenzo Bianconi1-1/+1
Fix the following sparse warning: drivers/net/wireless/mediatek/mt76/mt7921/mac.c:1425:70: warning: Using plain integer as NULL pointer Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7915: directly read per-rate tx power from registersShayne Chen2-22/+51
Since driver no longer handler per-rate tx power setting, we need to read the power values directly from registers. Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7915: rework the flow of txpower settingShayne Chen8-251/+99
Clean up the flow of per-rate txpower limit setting to get rid of duplicate work since it has already been handled by firmware, and set proper max_power based on different channels and regdomains. Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7915: add support for DT rate power limitsShayne Chen1-6/+38
Enable to limit per-rate max txpower from DT. Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7921: abort uncompleted scan by wifi resetSean Wang1-0/+8
Scan abort should be required for the uncompleted hardware scan interrupted by wifi reset. Otherwise, it is possible that the scan request after wifi reset gets error code -EBUSY from mac80211 and then blocks the reconnectting to the access point. Fixes: 0c1ce9884607 ("mt76: mt7921: add wifi reset support") Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7921: add wifisys reset support in debugfsSean Wang1-7/+16
Introduce chip_reset knob in mt7921 debugfs to export a way to users able to trigger wifi reset, and group the similar operations previously defined in chip_config in the same knob. Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7921: run mt7921_mcu_fw_log_2_host holding mt76 mutexLorenzo Bianconi1-1/+4
Wake the chip before configuring the mcu log level Fixes: 1d8efc741df8 ("mt76: mt7921: introduce Runtime PM support") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: improve mcu error loggingLorenzo Bianconi5-10/+8
Dump mcu command code in hex and related prefix to help debugging Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7921: move hw configuration in mt7921_register_deviceLorenzo Bianconi2-13/+6
Get rid of init work since firmware loading is already performed in mt7921_init_hardware Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7915: add support for applying pre-calibration dataRyder Lee9-10/+199
When the EEPROM data is read from flash, it can contain pre-calibration data, which can save calibration time. Note that group_cal can save 30% bootup calibration time, and dpd_cal can save 75% channel switching time. Tested-by: Bo Jiao <bo.jiao@mediatek.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7615: load ROM patch before checking patch semaphore statusFelix Fietkau1-14/+16
For MT7663, the availability of the patch files is used to detect, which corresponding firmware is going to be used (AP firmware or STA offload firmware). If the ROM patch was already applied, it could attempt to load the wrong firmware (without considering the alternative). Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7615: fix entering driver-own state on mt7663Felix Fietkau1-2/+10
Fixes hardware wakeup issues Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7615: fix hardware error recovery for mt7663Felix Fietkau5-11/+53
MT7663 uses different bits for communicating reset commands/status between MCU and host. Also add an extra initial reset command. Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7921: add dumping Tx power tableSean Wang5-0/+151
Dump the tx power table saved in offload firmware. Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: introduce single-sku support for mt7663/mt7921Lorenzo Bianconi6-1/+170
Introduce support for rate-txpower compensation for mt7663/mt7921 chipsets. Rate-txpower limit is specified through dts Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7615: do not use mt7615 single-sku values for mt7663Lorenzo Bianconi1-0/+5
mt7663 mcu relies on different APIs to configure APIs per-rate power limit respect to mt7615 driver. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7615: implement support for using DT rate power limitsFelix Fietkau2-2/+69
Limits are used to update the channel max_power settings and also passed to the firmware on channel changes Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: extend DT rate power limits to support 11ax devicesShayne Chen2-22/+39
Enable parsing per-rate txpower limits from DT for 11ax chipsets. Co-developed-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Felix Fietkau <nbd@nbd.name> Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: add functions for parsing rate power limits from DTFelix Fietkau2-0/+216
This subnode can be used to set per-rate tx power limits either per country code / regdomain or globally. These limits are typically provided by the device manufacturers and are used to limit sideband emissions and stay within regulatory limits Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: flush tx status queue on DMA resetFelix Fietkau5-0/+10
After DMA reset, tx status information for queued frames will never arrive. Flush the queue to free skbs immediately instead of waiting for a timeout Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7921: add mt7921_dma_cleanup in mt7921_unregister_deviceLorenzo Bianconi1-1/+2
In order to avoid memory leaks, clean the dma engine unloading the module Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7615: use ieee80211_free_txskb() in mt7615_tx_token_put()Ryder Lee1-2/+6
We should use ieee80211_free_txskb() to report skb status avoid wrong aql accounting after reset. Cc: stable@vger.kernel.org Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7615: only free skbs after mt7615_dma_reset() when reset happensRyder Lee1-3/+3
In mt7615_mac_reset_work(), make sure freeing skbs after mt7615_dma_reset(). Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7915: only free skbs after mt7915_dma_reset() when reset happensRyder Lee1-3/+3
In mt7915_mac_reset_work(), make sure freeing skbs after mt7915_dma_reset(). Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7915: fix memleak when mt7915_unregister_device()Ryder Lee1-2/+1
mt7915_tx_token_put() should get call before mt76_free_pending_txwi(). Fixes: f285dfb98562 ("mt76: mt7915: reset token when mac_reset happens") Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7615: fix memleak when mt7615_unregister_device()Ryder Lee1-2/+1
mt7615_tx_token_put() should get call before mt76_free_pending_txwi(). Fixes: a6275e934605 ("mt76: mt7615: reset token when mac_reset happens") Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7915: fix rate setting of tx descriptor in testmodeShayne Chen1-6/+19
Fix ofdm rate index and ldpc setting in rate setting field of tx descriptor. Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: mt7915: rework mt7915_tm_set_tx_len()Shayne Chen1-17/+5
Rework mt7915_tm_set_tx_len() with mt76_testmode_alloc_skb() to support larger packet based on a longer tx_time. Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-21mt76: testmode: add support to send larger packetShayne Chen4-35/+131
Add support to send larger packet in testmode to meet requirements of some test cases. The limit of max packet size is determined based on tx rate mode setting. Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-04-20Merge tag 'mac80211-next-for-net-next-2021-04-20' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-nextDavid S. Miller4-14/+14
Johannes Berg says: ==================== Another set of updates, all over the map: * set sk_pacing_shift for 802.3->802.11 encap offload * some monitor support for 802.11->802.3 decap offload * HE (802.11ax) spec updates * userspace API for TDLS HE support * along with various other small features, cleanups and fixups ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-19wireless: fix spelling of A-MSDU in HE capabilitiesJohannes Berg4-4/+4
In the HE capabilities, spell A-MSDU correctly, not "A-MDSU". Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20210409123755.9e6ff1af1181.If6868bc6902ccd9a95c74c78f716c4b41473ef14@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2021-04-19wireless: align HE capabilities A-MPDU Length Exponent ExtensionJohannes Berg2-2/+2
The A-MPDU length exponent extension is defined differently in 802.11ax D6.1, align with that. Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20210409123755.c2a257d3e2df.I3455245d388c52c61dace7e7958dbed7e807cfb6@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2021-04-19wireless: align some HE capabilities with the specJohannes Berg3-8/+8
Some names were changed, align that with the spec as of 802.11ax-D6.1. Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20210409123755.b1e5fbab0d8c.I3eb6076cb0714ec6aec6b8f9dee613ce4a05d825@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2021-04-17Merge tag 'mt76-for-kvalo-2021-04-12' of https://github.com/nbd168/wirelessKalle Valo66-1295/+2240
mt76 patches for 5.13 * code cleanup * mt7915/mt7615 decap offload support * driver fixes * mt7613 eeprom support * MCU code unification * threaded NAPI support * new device IDs * mt7921 device reset support * rx timestamp support # gpg: Signature made Tue 13 Apr 2021 12:11:25 AM EEST using DSA key ID 02A76EF5 # gpg: Good signature from "Felix Fietkau <nbd@nbd.name>" # gpg: WARNING: This key is not certified with a trusted signature! # gpg: There is no indication that the signature belongs to the owner. # Primary key fingerprint: 75D1 1A7D 91A7 710F 4900 42EF D77D 141D 02A7 6EF5
Copyright © 1996 – 2026 Jason A. Donenfeld. All Rights Reverse Engineered.