| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch enables 11h extensions in FW upon detecting DFS
channel in start radar detection/channel switch handlers.
Patch also takes care of disabling 11h when non DFS channels
are to be set during start_ap handler.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch adds support for cfg80211 start_radar_detection handler.
Upon reception of start_radar_detection, driver prepares radar detect
command to FW.
Delayed work is queued for CAC time which sends radar detection finished
event to cfg80211.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Currently interface limits are checked by seeing if bss_mode for
particular priv is set. If bss_mode is not set, interface creation
is allowed. This patch adds framework to initializes maximum virtual
interfaces supported during load time and check current number of
interfaces created agains allowed interface limit during new virtual
interface creation.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch adds support for DMA alignment of 64 bytes for TX packets.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch add a new debugfs item histogram used for reporting
rx data packet statitics(rx rate, snr, noise floor, signal strenth)
to userspace.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch add provision to show TDLS peer table in debugfs file.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
ACK status (0/1) for ACTION frames is informed to cfg80211. We
will extend existing logic used for EAPOL frames. The cfg80211
API is different here. Also, we need to explicitly free cloned
skb.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Firmware notifies the driver through event if EAPOL data packet
has been acked or not. We will inform this status to userspace
listening on a socket.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds auto TDLS support to mwifiex.
Auto TDLS functionality works as follows:
1. Whenever userspace application has triggered TDLS connection with
any peer, driver would store this peer mac address details in its database.
2. After this driver whenever driver receives packet on direct link,
it would store rssi and timestamp in peer information.
3. Whenever a packet is to be transmitted to non-AP peer in station mode,
driver would check if TDLS link can be established by looking at peer RSSI
information. Driver would initiate TDLS setup in such cases.
4. Periodic timer is used for updating peer information.
5. Auto TDLS peer list & timer are cleared during disconnection or driver unload.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds support to record channel statistics during
scan. With extended scan, scan results are returned as events from
FW while channel statistics are part of scan command response.
We store these channel statistics in adapter.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Xinmin Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch sets uAP BA window sizes to 64.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch updates mwifiex Copyright to 2014.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This will help to aggregate more packets which yields better
throughput results for 11ac chipsets.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This will help to aggregate more packets which yields better
throughput results.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds cfg80211 handler tdls_oper handler support to
mwifiex. Upon enable link, driver sets status as TDLS status as
setup complete and also sets AMSDU size, AMPDU params for direct
link. Upon disable link, driver issues command to FW to delete
this link in FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds support for parsing TDLS action frames during
station receive handler.
Peer station capabilities are stored into station node.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds support for TDLS management frames transmit
handler. mwifiex driver supports TDLS with external support,
i.e. expects user space application to form TDLS frames.
Same is advertised to cfg80211 during registration.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The skb is modified in sending the TX packet. Save the original
packet length to a variable so that we can get the correct
statistics update.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds support for dropping gratuitous ARP frames which is
requirement for WFA Hotspot2.0.
Hotspot2.0 capability is enabled in driver if extended capabilities
IE from BSS descriptor has 11u interworking enabled.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Delete packets from TX queues for this mwifiex_private structure
when bridged packet count reaches maximum threshold. Bridged packets
from each RA List are deleted till they fall to low threshold of 128.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Newer 11ac enabled chipsets have more TX and RX buffers in FW
and hardware; so they may support larger TX and RX window sizes
for BA. Reset BA settings during association, adhoc join/start
or start_ap() if we are joining/creating 11ac network.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Sagar Bijwe <bsagar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch fixes an issue where RX throughput values observed
were substantially lower than TX counterparts for PCIe8897 STA.
PCIe8897 supports larger rx_win_size. After changing these values
we see big improvement for TX and RX throughput values.
Different tx_win_size and rx_win_size are used for AP mode.
All BA setup related initialization has been moved to separate
function.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Sagar Bijwe <bsagar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch adds support for parsing WMM IEs from hostapd
and setting them to FW via sys configure command.
Patch also sets wiphy flag to advertise AP uAPSD support.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Due to firmware design, driver needs to add a default P2P interface
to implement find phase and action frame handshake.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Implement mgmt_tx in cfg80211 ops through data path.
Advertise probe resp offload and skip to send probe resp in AP
or GO mode.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
1. Separate file for uAP RX handling.
2. If received packet is broadcast/multicast, send it to kernel
as well as requeue it back to uAP TX queue.
3. If received packet is for associated STA (intra-BSS), requeue
it back to uAP TX queue.
4. In all other cases (packets for AP or inter-BSS packets),
pass packet to kernel to handle it accordingly.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
1) Remove unnecessary wrapper functions.
2) Currently we don't have command to set Tx data rate, so
mwifiex_rate_ioctl_set_rate_value() function and related code
can be removed.
3) "ds_rate" filled by mwifiex_ret_tx_rate_cfg() is never used.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
1. add start AP and stop AP handlers
2. support for parsing ssid, beacon period, DTIM period
from beacon_parameters structure and setting it to FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add support for setting fragmentation threshold, RTS threshold
and retry limit.
Since wiphy parameters are properties of physical device,
appropriate function to set phy parameters is invoked depending
upon bss_type(STA or AP) for each virtual interface.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Reserve space for one more priv structure.
This will be used by AP interface.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch supports Avastar 88W8797 chipset with USB interface.
The corresponding firmware image file is located at:
"mrvl/usb8797_uapsta.bin"
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Use struct cfg80211_ssid available in include/net/cfg80211.h
instead of having similar definition in driver.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Current implementation, for retrieving priv from adapter,
uses bss_index. In multi interface environment supporting
different types, bss_index may not be unique.
Use bss_type along with bss_num to retrieve the priv.
bss_index is removed with this change.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Currently global wait condition (adapter->cmd_wait_q.condition)
is used while sending synchronous commands to FW. When two threads
enter in mwifiex_send_cmd_sync() routine at the same time, both the
threads wait for their command responses. Since wait condition is
same for both, they wake up simultaneously after getting response
of 1st command. After this when a thread is waiting for command
response of 3rd command, it wakes up after getting response of 2nd
command and so on. Therefore we don't wait for the response of last
command(0xaa) during unload. Hence while next time loading the driver
command time out is seen for INIT command.
This problem is resolved by having separate wait condition flag for
each command(except scan command). Since scan command is treated
differently (by maintaining scan pending q etc.), newly defined flag
(scan_wait_q_woken) is used as a scan wait condition.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Making adding and deleting virtual interfaces dynamic. Adding
handlers for creating and deleting virtual interface with
given name and dev respectively.
Also, creating default interface of type station on insmod of
the driver.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In XMIT path, the skb that we get from the kernel itself is not
aligned with 4-byte boundary on some embedded platforms.
Had it not been the presence of tx_pkt_offset field in txpd, 4 byte
memory alignment was not possible without memmove of entire skb.
And that would have increased MIPS instead of reducing.
With this patch few memory cycles can be saved while fetching
interface header and txpd structure because of 4 bytes memory
alignment.
Reported-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
1) removal of unnecessary mwifiex_device structure
2) avoid passing adapter pointer to mwifiex_init_sw()
3) remove local variable drv_mode_info in mwifiex_add_card()
4) type change in mwifiex_bss_attr to match mwifiex_private
5) removal of more wordy comments
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
1) remove mwifiex_alloc_fill_wait_queue() and
mwifiex_request_ioctl()
2) avoid dynamic allocation of wait queue
3) remove unnecessary mwifiex_error_code macros that
were used mainly by the wait queue status code
4) remove some abstraction functions
5) split mwifiex_prepare_cmd() to mwifiex_send_cmd_async()
and mwifiex_send_sync() to handle asynchronous and
synchronous commands respectively
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
These macros are leftover of previous cleanup patches.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This driver adds WiFi support for Marvell 802.11n based chipsets
with SDIO interface. Currently only SD8787 is supported. More
chipsets will be supported later.
drivers/net/wireless/mwifiex/
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Ramesh Radhakrishnan <rramesh@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
Avinash Patil
Xinming Hu
Amitkumar Karwar
Ujjal Roy
Stone Piao
Yogesh Ashok Powar
Bing Zhao