| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Similar to rx_command_packet, we can call rtl_c2h_content_parsing so the
hal_op isn't necessary.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Because the hal_op rx_command_packet does C2H handler if rx packet type
is C2H, and the handler have been moved to base.c so we can call the
handler directly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Merge duplicate C2H handler and implement the handler in base.c.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We're going to merge C2H handler into one, but one special case is to
handle RA_REPORT that implements in individual IC folder. So this commit
adds a hal_op for caller in common code.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Move C2H definition to wifi.h, because the definitions of 8192ee, 8723be
and 8821ae are the same.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Move duplicate definitions from def.h of ic folder to wifi.h
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In order to realize the keep-alive mechanism in mac80211 stack, reporting
accurate tx ack status for nullfunc frame is added in this commit.
If current frame is nullfunc frame, we ask firmware to report by filling
TX report bit in TX descriptor. After this frame DMA done, TX interrupt is
triggered but TX status is unknown at this moment, so enqueue this skb
into tx_report->queue. Finally, C2H report will be received if the frame
is transmitted successfully or retried over, and then we report to mac80211
with IEEE80211_TX_STAT_ACK flag only if it's successful. Otherwise, if
failure or timeout (one second), we report to mac80211 without this flag.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Two enumerations bt_total_ant_num and bt_ant_num are identical, so one
can be removed.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Correct comment. Set bit 3 and bit 4 of 0x0005 register (REG_APS_FSMCO + 1)
to 0 which means disable WL suspend, not enable WL suspend.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Remove the duplicate checking of TX ring's available number, and remove
the variable to store available number that can be calculated by
read/write pointers.
Signed-off-by: Steven Ting <steventing@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Give correct fifo size to calculate fifo space. Fortunately, the values of
RTL_PCI_MAX_RX_COUNT and TX_DESC_NUM_92E are the same in old code, so it
still works.
Signed-off-by: Steven Ting <steventing@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
With the RTL8822BE and later devices, the number of interrupt vectors
has grown from 2 to 4. At this point, saving and passing those vectors
in a struct makes more sense than using individual scaler variables.
In two of the drivers, code to process the second of the interrupt
registers was included, but commented out. This patch removes those
useless sections.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
8822be checks H2CQ by int_d, so we extend to four ISR.
Also, irq_mask is extended to four.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On some platforms, enable ASPM will cause AER error to be logged, thus
we use a parameter to selectively turn on ASPM.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
- Add new parameter "is_bw_update" to control if current bandwidth setting
is updated to FW RA.
- After this commit, we keep the same setting as before.
- Later, bandwidth update in watchdog is changed to false for 8822BE.
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
1. Both 32-bit and 64-bit use the same TX/RX buffer desc layout
2. Extend set_desc() and get_desc() to set and get 64-bit address
3. Remove directive DMA_IS_64BIT
4. Add module parameter to turn on 64-bit dma
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In routine rtl92ee_set_fw_rsvdpagepkt(), the driver allocates an skb, but
never calls rtl_cmd_send_packet(), which will free the buffer. All other
rtlwifi drivers perform this operation correctly.
This problem has been in the driver since it was included in the kernel.
Fortunately, each firmware load only leaks 4 buffers, which likely
explains why it has not previously been detected.
Cc: Stable <stable@vger.kernel.org> # 3.18+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
1899 928 0 2827 b0b realtek/rtlwifi/rtl8192ee/sw.o
File size After adding 'const':
text data bss dec hex filename
1963 864 0 2827 b0b realtek/rtlwifi/rtl8192ee/sw.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch will fix memory leak when firmware request fails
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
With correct board_type, the phy praser can choose correct parameters.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We use H2C to ask BT's status, and C2H will return the status.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Remove useless local variables last_read_point and last_txw_point and
the code related.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Modify 8723be and 8192e only.
8812/8821 do IQK in DM, so we may do it later.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In this case, BTC asks to enter/leave PS mode frequently to cause A2DP
choppy.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Kalle Valo says:
====================
wireless-drivers-next patches for 4.13
New features and bug fixes to quite a few different drivers, but
nothing really special standing out.
What makes me happy that we have now more vendors actively
contributing to upstream drivers. In this pull request we have patches
from Broadcom, Intel, Qualcomm, Realtek and Redpine Signals, and I
still have patches from Marvell and Quantenna pending in patchwork. Now
that's something comparing to how things looked 11 years ago in Jeff
Garzik's "State of the Union: Wireless" email:
https://lkml.org/lkml/2006/1/5/671
Major changes:
wil6210
* add low level RF sector interface via nl80211 vendor commands
* add module parameter ftm_mode to load separate firmware for factory
testing
* support devices with different PCIe bar size
* add support for PCIe D3hot in system suspend
* remove ioctl interface which should not be in a wireless driver
ath10k
* go back to using dma_alloc_coherent() for firmware scratch memory
* add per chain RSSI reporting
brcmfmac
* add support multi-scheduled scan
* add scheduled scan support for specified BSSIDs
* add support for brcm43430 revision 0
wlcore
* add wil1285 compatible
rsi
* add RS9113 USB support
iwlwifi
* FW API documentation improvements (for tools and htmldoc)
* continuing work for the new A000 family
* bump the maximum supported FW API to 31
* improve the differentiation between 8000, 9000 and A000 families
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To yield better user experience, have btcoex control LPS's parameters.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add btcoex record pwr mode to control LPS's parameters and share time
with BT.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When using EAPOL to do a PTK rekey, there is a possible race condition.
When msg 3/4 is received, the supplicant will send msg 4/4 and install
the new key immediately; however, the driver must make sure that msg 4/4
is sent before installing the new key. We use TX report to ensure it is
sent.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
spatch file,
@@
expression skb, len, data;
type t;
@@
-memcpy((t *)skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
@@
identifier p;
expression skb, len, data;
type t;
@@
-p = (t *)memset(skb_put(skb, len), data, len);
+p = skb_put_zero(skb, len);
@@
expression skb, len, data;
type t;
@@
-memcpy((t *)__skb_put(skb, len), data, len);
+__skb_put_data(skb, data, len);
@@
identifier p;
expression skb, len, data;
type t;
@@
-p = (t *)memset(__skb_put(skb, len), data, len);
+p = __skb_put_zero(skb, len);
Signed-off-by: yuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
trivial fixes to spelling mistakes in RT_TRACE messages.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We currently use a lot of flags that are mutually incompatible,
separate this out into actual encoding and bandwidth enum values.
Much of this again done with spatch, with manual post-editing,
mostly to add the switch statements and get rid of the conversions.
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_80MHZ
+status->bw = RATE_INFO_BW_80
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_40MHZ
+status->bw = RATE_INFO_BW_40
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_20MHZ
+status->bw = RATE_INFO_BW_20
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_160MHZ
+status->bw = RATE_INFO_BW_160
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_5MHZ
+status->bw = RATE_INFO_BW_5
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_10MHZ
+status->bw = RATE_INFO_BW_10
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_VHT
+status->encoding = RX_ENC_VHT
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_HT
+status->encoding = RX_ENC_HT
@@
expression status;
@@
-status.enc_flags |= RX_ENC_FLAG_VHT
+status.encoding = RX_ENC_VHT
@@
expression status;
@@
-status.enc_flags |= RX_ENC_FLAG_HT
+status.encoding = RX_ENC_HT
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_HT)
+(status->encoding == RX_ENC_HT)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_VHT)
+(status->encoding == RX_ENC_VHT)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_5MHZ)
+(status->bw == RATE_INFO_BW_5)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_10MHZ)
+(status->bw == RATE_INFO_BW_10)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_40MHZ)
+(status->bw == RATE_INFO_BW_40)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_80MHZ)
+(status->bw == RATE_INFO_BW_80)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_160MHZ)
+(status->bw == RATE_INFO_BW_160)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In preparation for adding support for HE rates, clean up
the driver report encoding for rate/bandwidth reporting
on RX frames.
Much of this patch was done with the following spatch:
@@
expression status;
@@
-status->flag & (RX_FLAG_HT | RX_FLAG_VHT)
+status->enc_flags & (RX_ENC_FLAG_HT | RX_ENC_FLAG_VHT)
@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_SHORTPRE
+status->enc_flags op RX_ENC_FLAG_SHORTPRE
@@
expression status;
@@
-status->flag & RX_FLAG_SHORTPRE
+status->enc_flags & RX_ENC_FLAG_SHORTPRE
@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_HT
+status->enc_flags op RX_ENC_FLAG_HT
@@
expression status;
@@
-status->flag & RX_FLAG_HT
+status->enc_flags & RX_ENC_FLAG_HT
@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_40MHZ
+status->enc_flags op RX_ENC_FLAG_40MHZ
@@
expression status;
@@
-status->flag & RX_FLAG_40MHZ
+status->enc_flags & RX_ENC_FLAG_40MHZ
@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_SHORT_GI
+status->enc_flags op RX_ENC_FLAG_SHORT_GI
@@
expression status;
@@
-status->flag & RX_FLAG_SHORT_GI
+status->enc_flags & RX_ENC_FLAG_SHORT_GI
@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_HT_GF
+status->enc_flags op RX_ENC_FLAG_HT_GF
@@
expression status;
@@
-status->flag & RX_FLAG_HT_GF
+status->enc_flags & RX_ENC_FLAG_HT_GF
@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_VHT
+status->enc_flags op RX_ENC_FLAG_VHT
@@
expression status;
@@
-status->flag & RX_FLAG_VHT
+status->enc_flags & RX_ENC_FLAG_VHT
@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_STBC_MASK
+status->enc_flags op RX_ENC_FLAG_STBC_MASK
@@
expression status;
@@
-status->flag & RX_FLAG_STBC_MASK
+status->enc_flags & RX_ENC_FLAG_STBC_MASK
@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_LDPC
+status->enc_flags op RX_ENC_FLAG_LDPC
@@
expression status;
@@
-status->flag & RX_FLAG_LDPC
+status->enc_flags & RX_ENC_FLAG_LDPC
@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_10MHZ
+status->enc_flags op RX_ENC_FLAG_10MHZ
@@
expression status;
@@
-status->flag & RX_FLAG_10MHZ
+status->enc_flags & RX_ENC_FLAG_10MHZ
@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_5MHZ
+status->enc_flags op RX_ENC_FLAG_5MHZ
@@
expression status;
@@
-status->flag & RX_FLAG_5MHZ
+status->enc_flags & RX_ENC_FLAG_5MHZ
@@
assignment operator op;
expression status;
@@
-status->vht_flag op RX_VHT_FLAG_80MHZ
+status->enc_flags op RX_ENC_FLAG_80MHZ
@@
expression status;
@@
-status->vht_flag & RX_VHT_FLAG_80MHZ
+status->enc_flags & RX_ENC_FLAG_80MHZ
@@
assignment operator op;
expression status;
@@
-status->vht_flag op RX_VHT_FLAG_160MHZ
+status->enc_flags op RX_ENC_FLAG_160MHZ
@@
expression status;
@@
-status->vht_flag & RX_VHT_FLAG_160MHZ
+status->enc_flags & RX_ENC_FLAG_160MHZ
@@
assignment operator op;
expression status;
@@
-status->vht_flag op RX_VHT_FLAG_BF
+status->enc_flags op RX_ENC_FLAG_BF
@@
expression status;
@@
-status->vht_flag & RX_VHT_FLAG_BF
+status->enc_flags & RX_ENC_FLAG_BF
@@
assignment operator op;
expression status, STBC;
@@
-status->flag op STBC << RX_FLAG_STBC_SHIFT
+status->enc_flags op STBC << RX_ENC_FLAG_STBC_SHIFT
@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_SHORTPRE
+status.enc_flags op RX_ENC_FLAG_SHORTPRE
@@
expression status;
@@
-status.flag & RX_FLAG_SHORTPRE
+status.enc_flags & RX_ENC_FLAG_SHORTPRE
@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_HT
+status.enc_flags op RX_ENC_FLAG_HT
@@
expression status;
@@
-status.flag & RX_FLAG_HT
+status.enc_flags & RX_ENC_FLAG_HT
@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_40MHZ
+status.enc_flags op RX_ENC_FLAG_40MHZ
@@
expression status;
@@
-status.flag & RX_FLAG_40MHZ
+status.enc_flags & RX_ENC_FLAG_40MHZ
@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_SHORT_GI
+status.enc_flags op RX_ENC_FLAG_SHORT_GI
@@
expression status;
@@
-status.flag & RX_FLAG_SHORT_GI
+status.enc_flags & RX_ENC_FLAG_SHORT_GI
@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_HT_GF
+status.enc_flags op RX_ENC_FLAG_HT_GF
@@
expression status;
@@
-status.flag & RX_FLAG_HT_GF
+status.enc_flags & RX_ENC_FLAG_HT_GF
@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_VHT
+status.enc_flags op RX_ENC_FLAG_VHT
@@
expression status;
@@
-status.flag & RX_FLAG_VHT
+status.enc_flags & RX_ENC_FLAG_VHT
@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_STBC_MASK
+status.enc_flags op RX_ENC_FLAG_STBC_MASK
@@
expression status;
@@
-status.flag & RX_FLAG_STBC_MASK
+status.enc_flags & RX_ENC_FLAG_STBC_MASK
@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_LDPC
+status.enc_flags op RX_ENC_FLAG_LDPC
@@
expression status;
@@
-status.flag & RX_FLAG_LDPC
+status.enc_flags & RX_ENC_FLAG_LDPC
@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_10MHZ
+status.enc_flags op RX_ENC_FLAG_10MHZ
@@
expression status;
@@
-status.flag & RX_FLAG_10MHZ
+status.enc_flags & RX_ENC_FLAG_10MHZ
@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_5MHZ
+status.enc_flags op RX_ENC_FLAG_5MHZ
@@
expression status;
@@
-status.flag & RX_FLAG_5MHZ
+status.enc_flags & RX_ENC_FLAG_5MHZ
@@
assignment operator op;
expression status;
@@
-status.vht_flag op RX_VHT_FLAG_80MHZ
+status.enc_flags op RX_ENC_FLAG_80MHZ
@@
expression status;
@@
-status.vht_flag & RX_VHT_FLAG_80MHZ
+status.enc_flags & RX_ENC_FLAG_80MHZ
@@
assignment operator op;
expression status;
@@
-status.vht_flag op RX_VHT_FLAG_160MHZ
+status.enc_flags op RX_ENC_FLAG_160MHZ
@@
expression status;
@@
-status.vht_flag & RX_VHT_FLAG_160MHZ
+status.enc_flags & RX_ENC_FLAG_160MHZ
@@
assignment operator op;
expression status;
@@
-status.vht_flag op RX_VHT_FLAG_BF
+status.enc_flags op RX_ENC_FLAG_BF
@@
expression status;
@@
-status.vht_flag & RX_VHT_FLAG_BF
+status.enc_flags & RX_ENC_FLAG_BF
@@
assignment operator op;
expression status, STBC;
@@
-status.flag op STBC << RX_FLAG_STBC_SHIFT
+status.enc_flags op STBC << RX_ENC_FLAG_STBC_SHIFT
@@
@@
-RX_FLAG_STBC_SHIFT
+RX_ENC_FLAG_STBC_SHIFT
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Two additional preset responses are added to the reserved page on the
wifi device.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In commit 6773386f977c ("rtlwifi: rtl8192c-common: Fix "BUG: KASAN:"),
a BUG detected when CONFIG_KASAN=y was fixed by reordering the layouts
of struct rtl_pci_priv, and struct rtl_usb_priv so that the variables
used by both PCI and USB drivers have the same offsets in both structs.
The better fix of relocating the critical variables into struct rtl_priv
was deferred as these changes do not have to be applied to stable
kernels.
This change also removes CamelCase variables with pLed0 => pled0.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
btcoex needs to sleep, thus it must run in thread context.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The firmware is read from disk as a little-endian byte string. The code
that loads the firmware into the device transfers it as 4-byte quantities.
The routines that write multi-byte quantities on BE hardware assume that
the data are in CPU order, and automatically do the conversion to the LE
order required by the device. As a result, the firmware is transmitted
incorrectly. Rather than do multiple byte swaps on the data, the download
routine is revised to transmit bytes rather than dwords. Although the
number of I/O operations is increased, the firmware is not often loaded.
All drivers have the same bug, and use essentially the same code to
download firmware. These routines have been moved into rtlwifi.
Some CamelCase variables have been renamed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The debugging macros contain a parameter COMP_XX that could be used as a
mask; however, the code turns all these various bits on at the same time.
This change implements them as a proper mask, and adds module parameters
to set the mask at load time.
The current name "debug" for the debug level has been changed to
"debug_level" to better differentiate it from "debug_mask".
The debug routines have also been changed to interrogate the structure
that is loaded at entry time. As a result, the structure rtl_debug is no
longer needed, and all references to it are deleted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Kalle Valo says:
====================
wireless-drivers-next patches for 4.11
The most notable change here is the inclusion of airtime fairness
scheduling to ath9k. It prevents slow clients from hogging all the
airtime and unfairly slowing down faster clients.
Otherwise smaller changes and cleanup.
Major changes:
ath9k
* cleanup eeprom endian handling
* add airtime fairness scheduling
ath10k
* fix issues for new QCA9377 firmware version
* support dev_coredump() for firmware crash dump
* enable channel 169 on 5 GHz band
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The addresses of Wlan NIC registers are natural alignment, but some
drivers have bugs. These are evident on platforms that need natural
alignment to access registers. This change contains the following:
1. Function _rtl8821ae_dbi_read() is used to read one byte from DBI,
thus it should use rtl_read_byte().
2. Register 0x4C7 of 8192ee is single byte.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The symbol DBG_EMERG is no longer used and is removed.
In a number of places, the code has redundant messages. For example, if
the failure for the firmware to run is logged, it is not necessary to
log that the firmware has been started. In addition, extraneous braces are
removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is a step toward eliminating the RT_TRACE macros. Those calls that
have DBG_EMERG as the level are always logged, and they represent error
conditions, thus they are replaced with pr_err().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This macro can be replaced with WARN_ONCE. In addition to using a
standard debugging macro for these critical errors, we also get
a stack dump.
In rtl8821ae/hw.c, a senseless comment was removed, and an incorrect
indentation was fixed.
This patch also fixes two places in each of rtl8192ee, rtl8723be,
and rtl8821ae where the logical condition was incorrect.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
That's the default now, no need for makefiles to set it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
|
|
In commit d86e64768859 ("rtlwifi: rtl818x: constify local structures"),
the configuration struct for most of the drivers was changed to be
constant. The problem is that five of the modified drivers need to be
able to update the firmware name based on the exact model of the card.
As the file names were stored in one of the members of that struct,
these drivers would fail with a kernel BUG splat when they tried to
update the firmware name.
Rather than reverting the previous commit, I used a suggestion by
Johannes Berg and made the firmware file name pointers be local to
the routines that update the software variables.
The configuration struct of rtl8192cu, which was not touched in the
previous patch, is now constantfied.
Fixes: d86e64768859 ("rtlwifi: rtl818x: constify local structures")
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> # 4.8
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Only rtl8821ae implements WOWLAN; however, the other drivers may receive
a call requesting information about this mode. The other drivers need to
ignore the request rather than logging that the default branch of the
switch statement has been reached.
Reported by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Help along debugging by showing what switch/case variable is not
being processed in these messages.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
For structure types defined in the same file or local header files, find
top-level static structure declarations that have the following
properties:
1. Never reassigned.
2. Address never taken
3. Not passed to a top-level macro call
4. No pointer or array-typed field passed to a function or stored in a
variable.
Declare structures having all of these properties as const.
Done using Coccinelle.
Based on a suggestion by Joe Perches <joe@perches.com>.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The driver for RTL8192EE chips is converted to use the common routine
for getting the hardware information.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
Ping-Ke Shih
Tzu-En Huang
Kevin Lo
Larry Finger
David S. Miller
Greg Kroah-Hartman
Arvind Yadav
Souptick Joarder
Gustavo A. R. Silva
yuan linyu
Colin Ian King
Johannes Berg
Michael S. Tsirkin
Joe Perches
Julia Lawall