| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
With the RTL8822BE and later devices, the number of interrupt vectors
has grown from 2 to 4. At this point, saving and passing those vectors
in a struct makes more sense than using individual scaler variables.
In two of the drivers, code to process the second of the interrupt
registers was included, but commented out. This patch removes those
useless sections.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
8822be checks H2CQ by int_d, so we extend to four ISR.
Also, irq_mask is extended to four.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On some platforms, enable ASPM will cause AER error to be logged, thus
we use a parameter to selectively turn on ASPM.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
- Add new parameter "is_bw_update" to control if current bandwidth setting
is updated to FW RA.
- After this commit, we keep the same setting as before.
- Later, bandwidth update in watchdog is changed to false for 8822BE.
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
1. Both 32-bit and 64-bit use the same TX/RX buffer desc layout
2. Extend set_desc() and get_desc() to set and get 64-bit address
3. Remove directive DMA_IS_64BIT
4. Add module parameter to turn on 64-bit dma
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
2817 1040 0 3857 f11 realtek/rtlwifi/rtl8192se/sw.o
File size After adding 'const':
text data bss dec hex filename
3009 848 0 3857 f11 realtek/rtlwifi/rtl8192se/sw.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch will fix memory leak when firmware request fails
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_put, __skb_put };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_put, __skb_put };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
which actually doesn't cover pskb_put since there are only three
users overall.
A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently use a lot of flags that are mutually incompatible,
separate this out into actual encoding and bandwidth enum values.
Much of this again done with spatch, with manual post-editing,
mostly to add the switch statements and get rid of the conversions.
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_80MHZ
+status->bw = RATE_INFO_BW_80
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_40MHZ
+status->bw = RATE_INFO_BW_40
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_20MHZ
+status->bw = RATE_INFO_BW_20
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_160MHZ
+status->bw = RATE_INFO_BW_160
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_5MHZ
+status->bw = RATE_INFO_BW_5
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_10MHZ
+status->bw = RATE_INFO_BW_10
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_VHT
+status->encoding = RX_ENC_VHT
@@
expression status;
@@
-status->enc_flags |= RX_ENC_FLAG_HT
+status->encoding = RX_ENC_HT
@@
expression status;
@@
-status.enc_flags |= RX_ENC_FLAG_VHT
+status.encoding = RX_ENC_VHT
@@
expression status;
@@
-status.enc_flags |= RX_ENC_FLAG_HT
+status.encoding = RX_ENC_HT
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_HT)
+(status->encoding == RX_ENC_HT)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_VHT)
+(status->encoding == RX_ENC_VHT)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_5MHZ)
+(status->bw == RATE_INFO_BW_5)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_10MHZ)
+(status->bw == RATE_INFO_BW_10)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_40MHZ)
+(status->bw == RATE_INFO_BW_40)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_80MHZ)
+(status->bw == RATE_INFO_BW_80)
@@
expression status;
@@
-(status->enc_flags & RX_ENC_FLAG_160MHZ)
+(status->bw == RATE_INFO_BW_160)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In preparation for adding support for HE rates, clean up
the driver report encoding for rate/bandwidth reporting
on RX frames.
Much of this patch was done with the following spatch:
@@
expression status;
@@
-status->flag & (RX_FLAG_HT | RX_FLAG_VHT)
+status->enc_flags & (RX_ENC_FLAG_HT | RX_ENC_FLAG_VHT)
@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_SHORTPRE
+status->enc_flags op RX_ENC_FLAG_SHORTPRE
@@
expression status;
@@
-status->flag & RX_FLAG_SHORTPRE
+status->enc_flags & RX_ENC_FLAG_SHORTPRE
@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_HT
+status->enc_flags op RX_ENC_FLAG_HT
@@
expression status;
@@
-status->flag & RX_FLAG_HT
+status->enc_flags & RX_ENC_FLAG_HT
@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_40MHZ
+status->enc_flags op RX_ENC_FLAG_40MHZ
@@
expression status;
@@
-status->flag & RX_FLAG_40MHZ
+status->enc_flags & RX_ENC_FLAG_40MHZ
@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_SHORT_GI
+status->enc_flags op RX_ENC_FLAG_SHORT_GI
@@
expression status;
@@
-status->flag & RX_FLAG_SHORT_GI
+status->enc_flags & RX_ENC_FLAG_SHORT_GI
@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_HT_GF
+status->enc_flags op RX_ENC_FLAG_HT_GF
@@
expression status;
@@
-status->flag & RX_FLAG_HT_GF
+status->enc_flags & RX_ENC_FLAG_HT_GF
@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_VHT
+status->enc_flags op RX_ENC_FLAG_VHT
@@
expression status;
@@
-status->flag & RX_FLAG_VHT
+status->enc_flags & RX_ENC_FLAG_VHT
@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_STBC_MASK
+status->enc_flags op RX_ENC_FLAG_STBC_MASK
@@
expression status;
@@
-status->flag & RX_FLAG_STBC_MASK
+status->enc_flags & RX_ENC_FLAG_STBC_MASK
@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_LDPC
+status->enc_flags op RX_ENC_FLAG_LDPC
@@
expression status;
@@
-status->flag & RX_FLAG_LDPC
+status->enc_flags & RX_ENC_FLAG_LDPC
@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_10MHZ
+status->enc_flags op RX_ENC_FLAG_10MHZ
@@
expression status;
@@
-status->flag & RX_FLAG_10MHZ
+status->enc_flags & RX_ENC_FLAG_10MHZ
@@
assignment operator op;
expression status;
@@
-status->flag op RX_FLAG_5MHZ
+status->enc_flags op RX_ENC_FLAG_5MHZ
@@
expression status;
@@
-status->flag & RX_FLAG_5MHZ
+status->enc_flags & RX_ENC_FLAG_5MHZ
@@
assignment operator op;
expression status;
@@
-status->vht_flag op RX_VHT_FLAG_80MHZ
+status->enc_flags op RX_ENC_FLAG_80MHZ
@@
expression status;
@@
-status->vht_flag & RX_VHT_FLAG_80MHZ
+status->enc_flags & RX_ENC_FLAG_80MHZ
@@
assignment operator op;
expression status;
@@
-status->vht_flag op RX_VHT_FLAG_160MHZ
+status->enc_flags op RX_ENC_FLAG_160MHZ
@@
expression status;
@@
-status->vht_flag & RX_VHT_FLAG_160MHZ
+status->enc_flags & RX_ENC_FLAG_160MHZ
@@
assignment operator op;
expression status;
@@
-status->vht_flag op RX_VHT_FLAG_BF
+status->enc_flags op RX_ENC_FLAG_BF
@@
expression status;
@@
-status->vht_flag & RX_VHT_FLAG_BF
+status->enc_flags & RX_ENC_FLAG_BF
@@
assignment operator op;
expression status, STBC;
@@
-status->flag op STBC << RX_FLAG_STBC_SHIFT
+status->enc_flags op STBC << RX_ENC_FLAG_STBC_SHIFT
@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_SHORTPRE
+status.enc_flags op RX_ENC_FLAG_SHORTPRE
@@
expression status;
@@
-status.flag & RX_FLAG_SHORTPRE
+status.enc_flags & RX_ENC_FLAG_SHORTPRE
@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_HT
+status.enc_flags op RX_ENC_FLAG_HT
@@
expression status;
@@
-status.flag & RX_FLAG_HT
+status.enc_flags & RX_ENC_FLAG_HT
@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_40MHZ
+status.enc_flags op RX_ENC_FLAG_40MHZ
@@
expression status;
@@
-status.flag & RX_FLAG_40MHZ
+status.enc_flags & RX_ENC_FLAG_40MHZ
@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_SHORT_GI
+status.enc_flags op RX_ENC_FLAG_SHORT_GI
@@
expression status;
@@
-status.flag & RX_FLAG_SHORT_GI
+status.enc_flags & RX_ENC_FLAG_SHORT_GI
@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_HT_GF
+status.enc_flags op RX_ENC_FLAG_HT_GF
@@
expression status;
@@
-status.flag & RX_FLAG_HT_GF
+status.enc_flags & RX_ENC_FLAG_HT_GF
@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_VHT
+status.enc_flags op RX_ENC_FLAG_VHT
@@
expression status;
@@
-status.flag & RX_FLAG_VHT
+status.enc_flags & RX_ENC_FLAG_VHT
@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_STBC_MASK
+status.enc_flags op RX_ENC_FLAG_STBC_MASK
@@
expression status;
@@
-status.flag & RX_FLAG_STBC_MASK
+status.enc_flags & RX_ENC_FLAG_STBC_MASK
@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_LDPC
+status.enc_flags op RX_ENC_FLAG_LDPC
@@
expression status;
@@
-status.flag & RX_FLAG_LDPC
+status.enc_flags & RX_ENC_FLAG_LDPC
@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_10MHZ
+status.enc_flags op RX_ENC_FLAG_10MHZ
@@
expression status;
@@
-status.flag & RX_FLAG_10MHZ
+status.enc_flags & RX_ENC_FLAG_10MHZ
@@
assignment operator op;
expression status;
@@
-status.flag op RX_FLAG_5MHZ
+status.enc_flags op RX_ENC_FLAG_5MHZ
@@
expression status;
@@
-status.flag & RX_FLAG_5MHZ
+status.enc_flags & RX_ENC_FLAG_5MHZ
@@
assignment operator op;
expression status;
@@
-status.vht_flag op RX_VHT_FLAG_80MHZ
+status.enc_flags op RX_ENC_FLAG_80MHZ
@@
expression status;
@@
-status.vht_flag & RX_VHT_FLAG_80MHZ
+status.enc_flags & RX_ENC_FLAG_80MHZ
@@
assignment operator op;
expression status;
@@
-status.vht_flag op RX_VHT_FLAG_160MHZ
+status.enc_flags op RX_ENC_FLAG_160MHZ
@@
expression status;
@@
-status.vht_flag & RX_VHT_FLAG_160MHZ
+status.enc_flags & RX_ENC_FLAG_160MHZ
@@
assignment operator op;
expression status;
@@
-status.vht_flag op RX_VHT_FLAG_BF
+status.enc_flags op RX_ENC_FLAG_BF
@@
expression status;
@@
-status.vht_flag & RX_VHT_FLAG_BF
+status.enc_flags & RX_ENC_FLAG_BF
@@
assignment operator op;
expression status, STBC;
@@
-status.flag op STBC << RX_FLAG_STBC_SHIFT
+status.enc_flags op STBC << RX_ENC_FLAG_STBC_SHIFT
@@
@@
-RX_FLAG_STBC_SHIFT
+RX_ENC_FLAG_STBC_SHIFT
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Fix typos and add the following to the scripts/spelling.txt:
aligment||alignment
I did not touch the "N_BYTE_ALIGMENT" macro in
drivers/net/wireless/realtek/rtlwifi/wifi.h to avoid unpredictable
impact.
I fixed "_aligment_handler" in arch/openrisc/kernel/entry.S because
it is surrounded by #if 0 ... #endif. It is surely safe and I
confirmed "_alignment_handler" is correct.
I also fixed the "controler" I found in the same hunk in
arch/openrisc/kernel/head.S.
Link: http://lkml.kernel.org/r/1481573103-11329-8-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In commit 6773386f977c ("rtlwifi: rtl8192c-common: Fix "BUG: KASAN:"),
a BUG detected when CONFIG_KASAN=y was fixed by reordering the layouts
of struct rtl_pci_priv, and struct rtl_usb_priv so that the variables
used by both PCI and USB drivers have the same offsets in both structs.
The better fix of relocating the critical variables into struct rtl_priv
was deferred as these changes do not have to be applied to stable
kernels.
This change also removes CamelCase variables with pLed0 => pled0.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The debugging macros contain a parameter COMP_XX that could be used as a
mask; however, the code turns all these various bits on at the same time.
This change implements them as a proper mask, and adds module parameters
to set the mask at load time.
The current name "debug" for the debug level has been changed to
"debug_level" to better differentiate it from "debug_mask".
The debug routines have also been changed to interrogate the structure
that is loaded at entry time. As a result, the structure rtl_debug is no
longer needed, and all references to it are deleted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Kalle Valo says:
====================
wireless-drivers-next patches for 4.11
The most notable change here is the inclusion of airtime fairness
scheduling to ath9k. It prevents slow clients from hogging all the
airtime and unfairly slowing down faster clients.
Otherwise smaller changes and cleanup.
Major changes:
ath9k
* cleanup eeprom endian handling
* add airtime fairness scheduling
ath10k
* fix issues for new QCA9377 firmware version
* support dev_coredump() for firmware crash dump
* enable channel 169 on 5 GHz band
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a step toward eliminating the RT_TRACE macros. Those calls that
have DBG_EMERG as the level are always logged, and they represent error
conditions, thus they are replaced with pr_err().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This macro can be replaced with WARN_ONCE. In addition to using a
standard debugging macro for these critical errors, we also get
a stack dump.
In rtl8821ae/hw.c, a senseless comment was removed, and an incorrect
indentation was fixed.
This patch also fixes two places in each of rtl8192ee, rtl8723be,
and rtl8821ae where the logical condition was incorrect.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
That's the default now, no need for makefiles to set it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
|
|
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since this driver was added to the kernel, the checkpatch script was
modified to request that the address of the FSF not be included.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In commit d86e64768859 ("rtlwifi: rtl818x: constify local structures"),
the configuration struct for most of the drivers was changed to be
constant. The problem is that five of the modified drivers need to be
able to update the firmware name based on the exact model of the card.
As the file names were stored in one of the members of that struct,
these drivers would fail with a kernel BUG splat when they tried to
update the firmware name.
Rather than reverting the previous commit, I used a suggestion by
Johannes Berg and made the firmware file name pointers be local to
the routines that update the software variables.
The configuration struct of rtl8192cu, which was not touched in the
previous patch, is now constantfied.
Fixes: d86e64768859 ("rtlwifi: rtl818x: constify local structures")
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> # 4.8
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Only rtl8821ae implements WOWLAN; however, the other drivers may receive
a call requesting information about this mode. The other drivers need to
ignore the request rather than logging that the default branch of the
switch statement has been reached.
Reported by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Help along debugging by showing what switch/case variable is not
being processed in these messages.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
For structure types defined in the same file or local header files, find
top-level static structure declarations that have the following
properties:
1. Never reassigned.
2. Address never taken
3. Not passed to a top-level macro call
4. No pointer or array-typed field passed to a function or stored in a
variable.
Declare structures having all of these properties as const.
Done using Coccinelle.
Based on a suggestion by Joe Perches <joe@perches.com>.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
RT_TRACE does not add a newline to the end of a message and always
emits at KERN_DEBUG so these are susceptible to message interleaving
from other processes without the newline.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Compiling the rtlwifi drivers for ARM with gcc -Wextra warns about lots of
incorrect code that results from 'char' being unsigned here, e.g.
realtek/rtlwifi/rc.c:113:18: error: comparison is always true due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8188ee/dm.c:1070:22: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192ce/trx.c:54:16: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192cu/mac.c:601:16: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192de/trx.c:53:16: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192ee/phy.c:1268:12: error: comparison is always true due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192se/rf.c:150:20: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8723be/dm.c:877:29: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8723be/phy.c:386:16: error: comparison is always true due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8821ae/dm.c:1514:38: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8821ae/phy.c:1558:11: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8821ae/phy.c:386:24: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8821ae/trx.c:55:12: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/stats.c:31:16: error: comparison is always false due to limited range of data type [-Werror=type-limits]
This patch changes all uses of 'char' in this driver that refer to
8-bit integers to use 's8' instead, which is signed on all architectures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
There are nine copies of the _rtl88ee_read_adapter_info() function,
and most but not all of them cause a build warning in some configurations:
rtl8192de/hw.c: In function '_rtl92de_read_adapter_info':
rtl8192de/hw.c:1767:12: error: 'hwinfo' may be used uninitialized in this function [-Werror=maybe-uninitialized]
rtl8723ae/hw.c: In function '_rtl8723e_read_adapter_info.constprop':
rtlwifi/rtl8723ae/hw.c:1654:12: error: 'hwinfo' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The problem is that when rtlefuse->epromtype is something other than
EEPROM_BOOT_EFUSE, the rest of the function uses undefined data, resulting
in random behavior later.
Apparently, in some drivers, the problem was already found and fixed
but the fix did not make it into the others.
This picks one approach to deal with the problem and applies identical
code to all 9 files, to simplify the later consolidation of those.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
What about if "rtlphy->pwrgroup_cnt" is 2? In that case we would use an
uninitialized "chnlgroup" variable and probably crash. Maybe that can't
happen for some reason which is not obvious but in that case this patch
is harmless.
Setting it to zero seems like a standard default in the surrounding code
so it's probably fine here as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Smatch lists the following:
CHECK drivers/net/wireless/realtek/rtlwifi/rtl8192se/phy.c
drivers/net/wireless/realtek/rtlwifi/rtl8192se/phy.c:648 rtl92s_phy_set_rf_power_state() warn: inconsistent indenting
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Two of the module parameter descriptions show incorrect default values.
In addition the value for software encryption is not transferred to
the locations used by the driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Now that a new mac80211-based driver for Realtek devices has been submitted,
it is time to reorganize the directories. Rather than having directories
rtlwifi and rtl818x be in drivers/net/wireless/, they will now be in
drivers/net/wireless/realtek/. This change simplifies the directory
structure, but does not result in any configuration changes that are
visable to the user.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
Larry Finger
Ping-Ke Shih
David S. Miller
Greg Kroah-Hartman
Arvind Yadav
Souptick Joarder
Johannes Berg
Masahiro Yamada
Michael S. Tsirkin
Joe Perches
Julia Lawall
Arnd Bergmann
Dan Carpenter