| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In some cases the return value of a failing function is not being used
and the function typhoon_init_one() returns another negative error code
instead.
Signed-off-by: Thomas Preisner <thomas.preisner+linux@fau.de>
Signed-off-by: Milan Stephan <milan.stephan+linux@fau.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a few cases the err-variable is not set to a negative error code if a
function call in typhoon_init_one() fails and thus 0 is returned
instead.
It may be better to set err to the appropriate negative error
code before returning.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188841
Reported-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Thomas Preisner <thomas.preisner+linux@fau.de>
Signed-off-by: Milan Stephan <milan.stephan+linux@fau.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IP_MULTICAST_IF fails if sk_bound_dev_if is already set and the new index
does not match it. e.g.,
ntpd[15381]: setsockopt IP_MULTICAST_IF 192.168.1.23 fails: Invalid argument
Relax the check in setsockopt to allow setting mc_index to an L3 slave if
sk_bound_dev_if points to an L3 master.
Make a similar change for IPv6. In this case change the device lookup to
take the rcu_read_lock avoiding a refcnt. The rcu lock is also needed for
the lookup of a potential L3 master device.
This really only silences a setsockopt failure since uses of mc_index are
secondary to sk_bound_dev_if if it is set. In both cases, if either index
is an L3 slave or master, lookups are directed to the same FIB table so
relaxing the check at setsockopt time causes no harm.
Patch is based on a suggested change by Darwin for a problem noted in
their code base.
Suggested-by: Darwin Dingel <darwin.dingel@alliedtelesis.co.nz>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial fixes to spelling mistake "Ivalid" to "Invalid" in
brcmf_err error messages.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
trivial fix to spelling mistake in RT_TRACE message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The addresses of Wlan NIC registers are natural alignment, but some
drivers have bugs. These are evident on platforms that need natural
alignment to access registers. This change contains the following:
1. Function _rtl8821ae_dbi_read() is used to read one byte from DBI,
thus it should use rtl_read_byte().
2. Register 0x4C7 of 8192ee is single byte.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
cfg80211_ops structures are only passed as an argument to the function
wiphy_new. This argument is of type const, so cfg80211_ops strutures
having this property can be declared as const.
Done using Coccinelle
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct cfg80211_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
@@
wiphy_new(&i@p,...)
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct cfg80211_ops i;
File size before:
text data bss dec hex filename
21225 1954 16 23195 5a9b wireless/marvell/libertas/cfg.o
File size after:
text data bss dec hex filename
22041 1154 16 23211 5aab wireless/marvell/libertas/cfg.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The symbol DBG_EMERG is no longer used and is removed.
In a number of places, the code has redundant messages. For example, if
the failure for the firmware to run is logged, it is not necessary to
log that the firmware has been started. In addition, extraneous braces are
removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is a step toward eliminating the RT_TRACE macros. Those calls that
have DBG_EMERG as the level are always logged, and they represent error
conditions, thus they are replaced with pr_err().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is a step toward eliminating the RT_TRACE macros. Those calls that
have DBG_EMERG as the level are always logged, and they represent error
conditions, thus they are replaced with pr_err().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is a step toward eliminating the RT_TRACE macros. Those calls that
have DBG_EMERG as the level are always logged, and they represent error
conditions, thus they are replaced with pr_err().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is a step toward eliminating the RT_TRACE macros. Those calls that
have DBG_EMERG as the level are always logged, and they represent error
conditions, thus they are replaced with pr_err().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is a step toward eliminating the RT_TRACE macros. Those calls that
have DBG_EMERG as the level are always logged, and they represent error
conditions, thus they are replaced with pr_err().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is a step toward eliminating the RT_TRACE macros. Those calls that
have DBG_EMERG as the level are always logged, and they represent error
conditions, thus they are replaced with pr_err().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is a step toward eliminating the RT_TRACE macros. Those calls that
have DBG_EMERG as the level are always logged, and they represent error
conditions, thus they are replaced with pr_err().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is a step toward eliminating the RT_TRACE macros. Those calls that
have DBG_EMERG as the level are always logged, and they represent error
conditions, thus they are replaced with pr_err().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is a step toward eliminating the RT_TRACE macros. Those calls that
have DBG_EMERG as the level are always logged, and they represent error
conditions, thus they are replaced with pr_err().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is a step toward eliminating the RT_TRACE macros. Those calls that
have DBG_EMERG as the level are always logged, and they represent error
conditions, thus they are replaced with pr_err().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is a step toward eliminating the RT_TRACE macros. Those calls that
have DBG_EMERG as the level are always logged, and they represent error
conditions, thus they are replaced with pr_err().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
These messages are always logged and represent error conditions, thus
we can use pr_err().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This macro can be replaced with WARN_ONCE. In addition to using a
standard debugging macro for these critical errors, we also get
a stack dump.
In rtl8821ae/hw.c, a senseless comment was removed, and an incorrect
indentation was fixed.
This patch also fixes two places in each of rtl8192ee, rtl8723be,
and rtl8821ae where the logical condition was incorrect.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Do not perform mac80211 config and link_tuner at the same time,
this can possibly result in wrong RF or BBP configuration.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
msleep(1) can sleep much more time then requested 1ms, this is not good
on channel switch, which we want to be performed fast (i.e. to make scan
faster). Replace msleep() with usleep_range(), which has much smaller
maximum sleeping time boundary.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This procedure can sleep, hence mdelay is not needed.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We need to perform different actions (AGC and VCO calibrations and VGC
tuning) periodically at different intervals. We don't need separate
works for those, we can use link tuner work and just check for proper
interval on it.
This fixes performing AGC and VCO calibration when scanning on STA
mode. We need to be on-channel to perform those calibrations.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since we reset TX_PIN_CFG register, we have to finish recalibration.
Warn if this is not possible.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We have different modes of adjusting freq offset on different chips.
Call current adjustment similarly like vendor driver - mode1 .
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
MAX_LEN_CFG_MAX_PSDU specify maximum transmitted by HW AMPDU length
(0 - 8kB, 1 - 16kB, 2 - 32kB, 3 - 64kB). Set this option according to
remote stations capabilities (based on HT ampdu_factor). However limit
the value based our hardware TX capabilities as some chips can not send
more than 16kB (factor 1). Limit for all chips is currently 32kB
(factor 2), but perhaps for some chips this could be increased
to 64kB by setting drv_data->max_psdu to 3.
Since MAX_LEN_CFG_MAX_PSDU is global setting, on multi stations modes
(AP, IBSS, mesh) we limit according to less capable remote STA. We can
not set bigger value to speed up communication with some stations and
do not break communication with slow stations.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Do not set ampdu_density and ba_size for frames without AMPDU bit i.e.
frames that will not be aggregated to AMPDU.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Initalize max ampdu_factor supported by us based on rx chains, vendor
driver do the same.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Eric Biggers pointed out that the orinoco driver pointed scatterlists
at the stack.
Fix it by switching from ahash to shash. The result should be
simpler, faster, and more correct.
Cc: stable@vger.kernel.org # 4.9 only
Reported-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
We accidentally return success when adm8211_alloc_rings() fails but we
should preserve the error code.
Fixes: cc0b88cf5ecf ("[PATCH] Add adm8211 802.11b wireless driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
There's no need for this to be only __read_mostly, since
it's only written in a single way depending on the module
parameter, so that can be moved into the module's __init
function, and the ops can be __ro_after_init.
This is a little bit safer since it means the ops can't
be overwritten (accidentally or otherwise), which would
otherwise cause an arbitrary function or bad pointer to
be called.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Enable dynamic bandwidth signalling by setting the corresponding
bit in MAC control register.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Firmware has started making use of reserved field.
Accordingly change curr_pkt_filter from u16 to u32.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
If we have sdio work requests received when sdio card reset is
happening, we may end up accessing older save_adapter pointer
later which is already freed during card reset.
This patch solves the problem by cancelling those pending requests.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Enable advertising support for channel 169, 5Ghz so that
based on the regulatory domain(country code) this channel
shall be active for use. For example in countries like India
this channel shall be available for use with latest regulatory updates
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
'ath10k_mac_tx' does not seems to use the per station table
entry pointer 'sta' (struct ieee80211_sta), hence remove passing
this unused argument
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
With command to get board_id from otp, in the case of following
boot get otp board id result 0x00000000 board_id 0 chip_id 0
boot using board name 'bus=pci,bmi-chip-id=0,bmi-board-id=0"
...
failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-board-id=0 from
ath10k/QCA6174/hw3.0/board-2.bin
The invalid board_id=0 will be used as index to search in the board-2.bin.
Ignore the case with board_id=0, as it means the otp is not carrying
the board id information.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The txpower is being recalculated when adding interface to make sure
txpower won't overshoot the spec, and when removing the interface,
the txpower should again to be recalculated to restore the correct value
from the active interface list.
Following is one of the scenario
vdev0 is created as STA and connected: txpower:23
vdev1 is created as P2P_DEVICE for control interface: txpower:0
vdev2 is created as p2p go/gc interface: txpower is 21
So the vdev2@txpower:21 will be set to firmware when vdev2 is created.
When we tear down the vdev2, the txpower needs to be recalculated to
re-set it to vdev0@txpower:23 as vdev0/vdev1 are the active interface.
ath10k_pci mac vdev 0 peer create 8c:fd:f0:01:62:98
ath10k_pci mac vdev_id 0 txpower 23
... (adding interface)
ath10k_pci mac vdev create 2 (add interface) type 1 subtype 3
ath10k_pci mac vdev_id 2 txpower 21
ath10k_pci mac txpower 21
... (removing interface)
ath10k_pci mac vdev 2 delete (remove interface)
ath10k_pci vdev 1 txpower 0
ath10k_pci vdev 0 txpower 23
ath10k_pci mac txpower 23
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Whenever firmware crashes, and both CONFIG_ATH10K_DEBUGFS and
CONFIG_ALLOW_DEV_COREDUMP are enabled, dump information about the crash via a
devcoredump device. Dump can be read from userspace for further analysis from:
/sys/class/devcoredump/devcd*/data
As until now we have provided the firmware crash dump file via fw_crash_dump
debugfs keep it still available but deprecate and a warning print that the user
should switch to using dev_coredump.
Future improvement would be not to depend on CONFIG_ATH10K_DEBUGFS, as there
might be systems which want to get the firmware crash dump but not enable
debugfs. How to handle memory consumption is also something which needs to be
taken into account.
Signed-off-by: Arun Khandavalli <akhandav@qti.qualcomm.com>
[kvalo@qca.qualcomm.com: rebase, fixes, improve commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Ath10k reports the phy capability that supports P2P_DEVICE interface.
When we use the P2P supported wpa_supplicant to start connection, it'll
create two interfaces, one is wlan0 (vdev_id=0) and one is P2P_DEVICE
p2p-dev-wlan0 which is for p2p control channel (vdev_id=1).
ath10k_pci mac vdev create 0 (add interface) type 2 subtype 0
ath10k_add_interface: vdev_id: 0, txpower: 0, bss_power: 0
...
ath10k_pci mac vdev create 1 (add interface) type 2 subtype 1
ath10k_add_interface: vdev_id: 1, txpower: 0, bss_power: 0
And the txpower in per vif bss_conf will only be set to valid tx power when
the interface is assigned with channel_ctx.
But this P2P_DEVICE interface will never be used for any connection, so
that the uninitialized bss_conf.txpower=0 is assinged to the
arvif->txpower when interface created.
Since the txpower configuration is firmware per physical interface.
So the smallest txpower of all vifs will be the one limit the tx power
of the physical device, that causing the low txpower issue on other
active interfaces.
wlan0: Limiting TX power to 21 (24 - 3) dBm
ath10k_pci mac vdev_id 0 txpower 21
ath10k_mac_txpower_recalc: vdev_id: 1, txpower: 0
ath10k_mac_txpower_recalc: vdev_id: 0, txpower: 21
ath10k_pci mac txpower 0
This issue only happens when we use the wpa_supplicant that supports
P2P or if we use the iw tool to create the control P2P_DEVICE interface.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
ath10k_wmi_tlv_op_pull_fw_stats() uses tb = ath10k_wmi_tlv_parse_alloc(...)
function, which allocates memory. If any of the three error-paths are
taken, this tb needs to be freed.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Reads from Octeon PCI console are inefficient because before each read
operation, a dynamic mapping to Octeon DRAM is set up. This patch replaces
the repeated setup of a dynamic mapping with a one-time setup of a static
mapping.
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement ndo_get_phys_port_id() by returning the physical port number
of the switch this per-port DSA created network interface corresponds
to.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Oftenly, introducing side effects on packet processing on the other half
of the stack by adjusting one of TX/RX via sysctl is not desirable.
There are cases of demand for asymmetric, orthogonal configurability.
This holds true especially for nodes where RPS for RFS usage on top is
configured and therefore use the 'old dev_weight'. This is quite a
common base configuration setup nowadays, even with NICs of superior processing
support (e.g. aRFS).
A good example use case are nodes acting as noSQL data bases with a
large number of tiny requests and rather fewer but large packets as responses.
It's affordable to have large budget and rx dev_weights for the
requests. But as a side effect having this large a number on TX
processed in one run can overwhelm drivers.
This patch therefore introduces an independent configurability via sysctl to
userland.
Signed-off-by: Matthias Tafelmeier <matthias.tafelmeier@gmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds Energy Efficiency Ethernet to GMAC4.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch refactors sctp_datamsg_from_user() in an attempt to make it
better to read and avoid code duplication for handling the last
fragment.
It also avoids doing division and remaining operations. Even though, it
should still operate similarly as before this patch.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Thomas Preisner
David Ahern
Colin Ian King
Ping-Ke Shih
Bhumika Goyal
Larry Finger
Stanislaw Gruszka
Andrew Lutomirski
Dan Carpenter
Johannes Berg
Amitkumar Karwar
Mohammed Shafi Shajakhan
Ryan Hsu
Arun Khandavalli
Christian Lamparter
Felix Manlunas
Florian Fainelli
Matthias Tafelmeier
jpinto
Marcelo Ricardo Leitner