aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net (follow)
AgeCommit message (Collapse)AuthorFilesLines
2019-04-07net: vrf: Fix ping failed when vrf mtu is set to 0Miaohe Lin1-2/+6
When the mtu of a vrf device is set to 0, it would cause ping failed. So I think we should limit vrf mtu in a reasonable range to solve this problem. I set dev->min_mtu to IPV6_MIN_MTU, so it will works for both ipv4 and ipv6. And if dev->max_mtu still be 0 can be confusing, so I set dev->max_mtu to ETH_MAX_MTU. Here is the reproduce step: 1.Config vrf interface and set mtu to 0: 3: enp4s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel master vrf1 state UP mode DEFAULT group default qlen 1000 link/ether 52:54:00:9e:dd:c1 brd ff:ff:ff:ff:ff:ff 2.Ping peer: 3: enp4s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel master vrf1 state UP group default qlen 1000 link/ether 52:54:00:9e:dd:c1 brd ff:ff:ff:ff:ff:ff inet 10.0.0.1/16 scope global enp4s0 valid_lft forever preferred_lft forever connect: Network is unreachable 3.Set mtu to default value, ping works: PING 10.0.0.2 (10.0.0.2) 56(84) bytes of data. 64 bytes from 10.0.0.2: icmp_seq=1 ttl=64 time=1.88 ms Fixes: ad49bc6361ca2 ("net: vrf: remove MTU limits for vrf device") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-04ibmvnic: Fix completion structure initializationThomas Falcon1-2/+3
Fix device initialization completion handling for vNIC adapters. Initialize the completion structure on probe and reinitialize when needed. This also fixes a race condition during kdump where the driver can attempt to access the completion struct before it is initialized: Unable to handle kernel paging request for data at address 0x00000000 Faulting instruction address: 0xc0000000081acbe0 Oops: Kernel access of bad area, sig: 11 [#1] LE SMP NR_CPUS=2048 NUMA pSeries Modules linked in: ibmvnic(+) ibmveth sunrpc overlay squashfs loop CPU: 19 PID: 301 Comm: systemd-udevd Not tainted 4.18.0-64.el8.ppc64le #1 NIP: c0000000081acbe0 LR: c0000000081ad964 CTR: c0000000081ad900 REGS: c000000027f3f990 TRAP: 0300 Not tainted (4.18.0-64.el8.ppc64le) MSR: 800000010280b033 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI,LE,TM[E]> CR: 28228288 XER: 00000006 CFAR: c000000008008934 DAR: 0000000000000000 DSISR: 40000000 IRQMASK: 1 GPR00: c0000000081ad964 c000000027f3fc10 c0000000095b5800 c0000000221b4e58 GPR04: 0000000000000003 0000000000000001 000049a086918581 00000000000000d4 GPR08: 0000000000000007 0000000000000000 ffffffffffffffe8 d0000000014dde28 GPR12: c0000000081ad900 c000000009a00c00 0000000000000001 0000000000000100 GPR16: 0000000000000038 0000000000000007 c0000000095e2230 0000000000000006 GPR20: 0000000000400140 0000000000000001 c00000000910c880 0000000000000000 GPR24: 0000000000000000 0000000000000006 0000000000000000 0000000000000003 GPR28: 0000000000000001 0000000000000001 c0000000221b4e60 c0000000221b4e58 NIP [c0000000081acbe0] __wake_up_locked+0x50/0x100 LR [c0000000081ad964] complete+0x64/0xa0 Call Trace: [c000000027f3fc10] [c000000027f3fc60] 0xc000000027f3fc60 (unreliable) [c000000027f3fc60] [c0000000081ad964] complete+0x64/0xa0 [c000000027f3fca0] [d0000000014dad58] ibmvnic_handle_crq+0xce0/0x1160 [ibmvnic] [c000000027f3fd50] [d0000000014db270] ibmvnic_tasklet+0x98/0x130 [ibmvnic] [c000000027f3fda0] [c00000000813f334] tasklet_action_common.isra.3+0xc4/0x1a0 [c000000027f3fe00] [c000000008cd13f4] __do_softirq+0x164/0x400 [c000000027f3fef0] [c00000000813ed64] irq_exit+0x184/0x1c0 [c000000027f3ff20] [c0000000080188e8] __do_irq+0xb8/0x210 [c000000027f3ff90] [c00000000802d0a4] call_do_irq+0x14/0x24 [c000000026a5b010] [c000000008018adc] do_IRQ+0x9c/0x130 [c000000026a5b060] [c000000008008ce4] hardware_interrupt_common+0x114/0x120 Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-04libcxgb: fix incorrect ppmax calculationVarun Prakash1-1/+8
BITS_TO_LONGS() uses DIV_ROUND_UP() because of this ppmax value can be greater than available per cpu page pods. This patch removes BITS_TO_LONGS() to fix this issue. Signed-off-by: Varun Prakash <varun@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-04net: thunderx: fix NULL pointer dereference in nicvf_open/nicvf_stopLorenzo Bianconi1-8/+12
When a bpf program is uploaded, the driver computes the number of xdp tx queues resulting in the allocation of additional qsets. Starting from commit '2ecbe4f4a027 ("net: thunderx: replace global nicvf_rx_mode_wq work queue for all VFs to private for each of them")' the driver runs link state polling for each VF resulting in the following NULL pointer dereference: [ 56.169256] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000020 [ 56.178032] Mem abort info: [ 56.180834] ESR = 0x96000005 [ 56.183877] Exception class = DABT (current EL), IL = 32 bits [ 56.189792] SET = 0, FnV = 0 [ 56.192834] EA = 0, S1PTW = 0 [ 56.195963] Data abort info: [ 56.198831] ISV = 0, ISS = 0x00000005 [ 56.202662] CM = 0, WnR = 0 [ 56.205619] user pgtable: 64k pages, 48-bit VAs, pgdp = 0000000021f0c7a0 [ 56.212315] [0000000000000020] pgd=0000000000000000, pud=0000000000000000 [ 56.219094] Internal error: Oops: 96000005 [#1] SMP [ 56.260459] CPU: 39 PID: 2034 Comm: ip Not tainted 5.1.0-rc3+ #3 [ 56.266452] Hardware name: GIGABYTE R120-T33/MT30-GS1, BIOS T49 02/02/2018 [ 56.273315] pstate: 80000005 (Nzcv daif -PAN -UAO) [ 56.278098] pc : __ll_sc___cmpxchg_case_acq_64+0x4/0x20 [ 56.283312] lr : mutex_lock+0x2c/0x50 [ 56.286962] sp : ffff0000219af1b0 [ 56.290264] x29: ffff0000219af1b0 x28: ffff800f64de49a0 [ 56.295565] x27: 0000000000000000 x26: 0000000000000015 [ 56.300865] x25: 0000000000000000 x24: 0000000000000000 [ 56.306165] x23: 0000000000000000 x22: ffff000011117000 [ 56.311465] x21: ffff800f64dfc080 x20: 0000000000000020 [ 56.316766] x19: 0000000000000020 x18: 0000000000000001 [ 56.322066] x17: 0000000000000000 x16: ffff800f2e077080 [ 56.327367] x15: 0000000000000004 x14: 0000000000000000 [ 56.332667] x13: ffff000010964438 x12: 0000000000000002 [ 56.337967] x11: 0000000000000000 x10: 0000000000000c70 [ 56.343268] x9 : ffff0000219af120 x8 : ffff800f2e077d50 [ 56.348568] x7 : 0000000000000027 x6 : 000000062a9d6a84 [ 56.353869] x5 : 0000000000000000 x4 : ffff800f2e077480 [ 56.359169] x3 : 0000000000000008 x2 : ffff800f2e077080 [ 56.364469] x1 : 0000000000000000 x0 : 0000000000000020 [ 56.369770] Process ip (pid: 2034, stack limit = 0x00000000c862da3a) [ 56.376110] Call trace: [ 56.378546] __ll_sc___cmpxchg_case_acq_64+0x4/0x20 [ 56.383414] drain_workqueue+0x34/0x198 [ 56.387247] nicvf_open+0x48/0x9e8 [nicvf] [ 56.391334] nicvf_open+0x898/0x9e8 [nicvf] [ 56.395507] nicvf_xdp+0x1bc/0x238 [nicvf] [ 56.399595] dev_xdp_install+0x68/0x90 [ 56.403333] dev_change_xdp_fd+0xc8/0x240 [ 56.407333] do_setlink+0x8e0/0xbe8 [ 56.410810] __rtnl_newlink+0x5b8/0x6d8 [ 56.414634] rtnl_newlink+0x54/0x80 [ 56.418112] rtnetlink_rcv_msg+0x22c/0x2f8 [ 56.422199] netlink_rcv_skb+0x60/0x120 [ 56.426023] rtnetlink_rcv+0x28/0x38 [ 56.429587] netlink_unicast+0x1c8/0x258 [ 56.433498] netlink_sendmsg+0x1b4/0x350 [ 56.437410] sock_sendmsg+0x4c/0x68 [ 56.440887] ___sys_sendmsg+0x240/0x280 [ 56.444711] __sys_sendmsg+0x68/0xb0 [ 56.448275] __arm64_sys_sendmsg+0x2c/0x38 [ 56.452361] el0_svc_handler+0x9c/0x128 [ 56.456186] el0_svc+0x8/0xc [ 56.459056] Code: 35ffff91 2a1003e0 d65f03c0 f9800011 (c85ffc10) [ 56.465166] ---[ end trace 4a57fdc27b0a572c ]--- [ 56.469772] Kernel panic - not syncing: Fatal exception Fix it by checking nicvf_rx_mode_wq pointer in nicvf_open and nicvf_stop Fixes: 2ecbe4f4a027 ("net: thunderx: replace global nicvf_rx_mode_wq work queue for all VFs to private for each of them") Fixes: 2c632ad8bc74 ("net: thunderx: move link state polling function to VF") Reported-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Tested-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-04net: hns: Fix sparse: some warnings in HNS driversYonglong Liu11-43/+33
There are some sparse warnings in the HNS drivers: warning: incorrect type in assignment (different address spaces) expected void [noderef] <asn:2> *io_base got void *vaddr warning: cast removes address space '<asn:2>' of expression [...] Add __iomem and change all the u8 __iomem to void __iomem to fix these kind of warnings. warning: incorrect type in argument 1 (different address spaces) expected void [noderef] <asn:2> *base got unsigned char [usertype] *base_addr warning: cast to restricted __le16 warning: incorrect type in assignment (different base types) expected unsigned int [usertype] tbl_tcam_data_high got restricted __le32 [usertype] warning: cast to restricted __le32 [...] These variables used u32/u16 as their type, and finally as a parameter of writel(), writel() will do the cpu_to_le32 coversion so remove the little endian covert code to fix these kind of warnings. Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-04net: hns: Fix WARNING when remove HNS driver with SMMU enabledYonglong Liu1-1/+3
When enable SMMU, remove HNS driver will cause a WARNING: [ 141.924177] WARNING: CPU: 36 PID: 2708 at drivers/iommu/dma-iommu.c:443 __iommu_dma_unmap+0xc0/0xc8 [ 141.954673] Modules linked in: hns_enet_drv(-) [ 141.963615] CPU: 36 PID: 2708 Comm: rmmod Tainted: G W 5.0.0-rc1-28723-gb729c57de95c-dirty #32 [ 141.983593] Hardware name: Huawei D05/D05, BIOS Hisilicon D05 UEFI Nemo 1.8 RC0 08/31/2017 [ 142.000244] pstate: 60000005 (nZCv daif -PAN -UAO) [ 142.009886] pc : __iommu_dma_unmap+0xc0/0xc8 [ 142.018476] lr : __iommu_dma_unmap+0xc0/0xc8 [ 142.027066] sp : ffff000013533b90 [ 142.033728] x29: ffff000013533b90 x28: ffff8013e6983600 [ 142.044420] x27: 0000000000000000 x26: 0000000000000000 [ 142.055113] x25: 0000000056000000 x24: 0000000000000015 [ 142.065806] x23: 0000000000000028 x22: ffff8013e66eee68 [ 142.076499] x21: ffff8013db919800 x20: 0000ffffefbff000 [ 142.087192] x19: 0000000000001000 x18: 0000000000000007 [ 142.097885] x17: 000000000000000e x16: 0000000000000001 [ 142.108578] x15: 0000000000000019 x14: 363139343a70616d [ 142.119270] x13: 6e75656761705f67 x12: 0000000000000000 [ 142.129963] x11: 00000000ffffffff x10: 0000000000000006 [ 142.140656] x9 : 1346c1aa88093500 x8 : ffff0000114de4e0 [ 142.151349] x7 : 6662666578303d72 x6 : ffff0000105ffec8 [ 142.162042] x5 : 0000000000000000 x4 : 0000000000000000 [ 142.172734] x3 : 00000000ffffffff x2 : ffff0000114de500 [ 142.183427] x1 : 0000000000000000 x0 : 0000000000000035 [ 142.194120] Call trace: [ 142.199030] __iommu_dma_unmap+0xc0/0xc8 [ 142.206920] iommu_dma_unmap_page+0x20/0x28 [ 142.215335] __iommu_unmap_page+0x40/0x60 [ 142.223399] hnae_unmap_buffer+0x110/0x134 [ 142.231639] hnae_free_desc+0x6c/0x10c [ 142.239177] hnae_fini_ring+0x14/0x34 [ 142.246540] hnae_fini_queue+0x2c/0x40 [ 142.254080] hnae_put_handle+0x38/0xcc [ 142.261619] hns_nic_dev_remove+0x54/0xfc [hns_enet_drv] [ 142.272312] platform_drv_remove+0x24/0x64 [ 142.280552] device_release_driver_internal+0x17c/0x20c [ 142.291070] driver_detach+0x4c/0x90 [ 142.298259] bus_remove_driver+0x5c/0xd8 [ 142.306148] driver_unregister+0x2c/0x54 [ 142.314037] platform_driver_unregister+0x10/0x18 [ 142.323505] hns_nic_dev_driver_exit+0x14/0xf0c [hns_enet_drv] [ 142.335248] __arm64_sys_delete_module+0x214/0x25c [ 142.344891] el0_svc_common+0xb0/0x10c [ 142.352430] el0_svc_handler+0x24/0x80 [ 142.359968] el0_svc+0x8/0x7c0 [ 142.366104] ---[ end trace 60ad1cd58e63c407 ]--- The tx ring buffer map when xmit and unmap when xmit done. So in hnae_init_ring() did not map tx ring buffer, but in hnae_fini_ring() have a unmap operation for tx ring buffer, which is already unmapped when xmit done, than cause this WARNING. The hnae_alloc_buffers() is called in hnae_init_ring(), so the hnae_free_buffers() should be in hnae_fini_ring(), not in hnae_free_desc(). In hnae_fini_ring(), adds a check is_rx_ring() as in hnae_init_ring(). When the ring buffer is tx ring, adds a piece of code to ensure that the tx ring is unmap. Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-04net: hns: fix ICMP6 neighbor solicitation messages discard problemYonglong Liu1-6/+27
ICMP6 neighbor solicitation messages will be discard by the Hip06 chips, because of not setting forwarding pool. Enable promisc mode has the same problem. This patch fix the wrong forwarding table configs for the multicast vague matching when enable promisc mode, and add forwarding pool for the forwarding table. Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-04net: hns: Fix probabilistic memory overwrite when HNS driver initializedYonglong Liu1-1/+1
When reboot the system again and again, may cause a memory overwrite. [ 15.638922] systemd[1]: Reached target Swap. [ 15.667561] tun: Universal TUN/TAP device driver, 1.6 [ 15.676756] Bridge firewalling registered [ 17.344135] Unable to handle kernel paging request at virtual address 0000000200000040 [ 17.352179] Mem abort info: [ 17.355007] ESR = 0x96000004 [ 17.358105] Exception class = DABT (current EL), IL = 32 bits [ 17.364112] SET = 0, FnV = 0 [ 17.367209] EA = 0, S1PTW = 0 [ 17.370393] Data abort info: [ 17.373315] ISV = 0, ISS = 0x00000004 [ 17.377206] CM = 0, WnR = 0 [ 17.380214] user pgtable: 4k pages, 48-bit VAs, pgdp = (____ptrval____) [ 17.386926] [0000000200000040] pgd=0000000000000000 [ 17.391878] Internal error: Oops: 96000004 [#1] SMP [ 17.396824] CPU: 23 PID: 95 Comm: kworker/u130:0 Tainted: G E 4.19.25-1.2.78.aarch64 #1 [ 17.414175] Hardware name: Huawei TaiShan 2280 /BC11SPCD, BIOS 1.54 08/16/2018 [ 17.425615] Workqueue: events_unbound async_run_entry_fn [ 17.435151] pstate: 00000005 (nzcv daif -PAN -UAO) [ 17.444139] pc : __mutex_lock.isra.1+0x74/0x540 [ 17.453002] lr : __mutex_lock.isra.1+0x3c/0x540 [ 17.461701] sp : ffff000100d9bb60 [ 17.469146] x29: ffff000100d9bb60 x28: 0000000000000000 [ 17.478547] x27: 0000000000000000 x26: ffff802fb8945000 [ 17.488063] x25: 0000000000000000 x24: ffff802fa32081a8 [ 17.497381] x23: 0000000000000002 x22: ffff801fa2b15220 [ 17.506701] x21: ffff000009809000 x20: ffff802fa23a0888 [ 17.515980] x19: ffff801fa2b15220 x18: 0000000000000000 [ 17.525272] x17: 0000000200000000 x16: 0000000200000000 [ 17.534511] x15: 0000000000000000 x14: 0000000000000000 [ 17.543652] x13: ffff000008d95db8 x12: 000000000000000d [ 17.552780] x11: ffff000008d95d90 x10: 0000000000000b00 [ 17.561819] x9 : ffff000100d9bb90 x8 : ffff802fb89d6560 [ 17.570829] x7 : 0000000000000004 x6 : 00000004a1801d05 [ 17.579839] x5 : 0000000000000000 x4 : 0000000000000000 [ 17.588852] x3 : ffff802fb89d5a00 x2 : 0000000000000000 [ 17.597734] x1 : 0000000200000000 x0 : 0000000200000000 [ 17.606631] Process kworker/u130:0 (pid: 95, stack limit = 0x(____ptrval____)) [ 17.617438] Call trace: [ 17.623349] __mutex_lock.isra.1+0x74/0x540 [ 17.630927] __mutex_lock_slowpath+0x24/0x30 [ 17.638602] mutex_lock+0x50/0x60 [ 17.645295] drain_workqueue+0x34/0x198 [ 17.652623] __sas_drain_work+0x7c/0x168 [ 17.659903] sas_drain_work+0x60/0x68 [ 17.666947] hisi_sas_scan_finished+0x30/0x40 [hisi_sas_main] [ 17.676129] do_scsi_scan_host+0x70/0xb0 [ 17.683534] do_scan_async+0x20/0x228 [ 17.690586] async_run_entry_fn+0x4c/0x1d0 [ 17.697997] process_one_work+0x1b4/0x3f8 [ 17.705296] worker_thread+0x54/0x470 Every time the call trace is not the same, but the overwrite address is always the same: Unable to handle kernel paging request at virtual address 0000000200000040 The root cause is, when write the reg XGMAC_MAC_TX_LF_RF_CONTROL_REG, didn't use the io_base offset. Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-04net: hns: Use NAPI_POLL_WEIGHT for hns driverYonglong Liu1-5/+2
When the HNS driver loaded, always have an error print: "netif_napi_add() called with weight 256" This is because the kernel checks the NAPI polling weights requested by drivers and it prints an error message if a driver requests a weight bigger than 64. So use NAPI_POLL_WEIGHT to fix it. Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-04net: hns: fix KASAN: use-after-free in hns_nic_net_xmit_hw()Liubin Shu1-2/+3
This patch is trying to fix the issue due to: [27237.844750] BUG: KASAN: use-after-free in hns_nic_net_xmit_hw+0x708/0xa18[hns_enet_drv] After hnae_queue_xmit() in hns_nic_net_xmit_hw(), can be interrupted by interruptions, and than call hns_nic_tx_poll_one() to handle the new packets, and free the skb. So, when turn back to hns_nic_net_xmit_hw(), calling skb->len will cause use-after-free. This patch update tx ring statistics in hns_nic_tx_poll_one() to fix the bug. Signed-off-by: Liubin Shu <shuliubin@huawei.com> Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-03iwlwifi: add support for quz firmwaresLuca Coelho4-2/+22
Add a new configuration with a new firmware name for quz devices. And, since these devices have the same PCI device and subsystem IDs, we need to add some code to switch from a normal qu firmware to the quz firmware. Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-03iwlwifi: mvm: update offloaded rate control on changesJohannes Berg1-0/+7
With offloaded rate control, if the station parameters (rates, NSS, bandwidth) change (sta_rc_update method), call iwl_mvm_rs_rate_init() to propagate those change to the firmware. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-03iwlwifi: mvm: avoid possible deadlock in TX pathJohannes Berg1-0/+2
iwl_mvm_tx_mpdu() may run from iwl_mvm_add_new_dqa_stream_wk(), where soft-IRQs aren't disabled. In this case, it may hold the station lock and be interrupted by a soft-IRQ that also wants to acquire said lock, leading to a deadlock. Fix it by disabling soft-IRQs in iwl_mvm_add_new_dqa_stream_wk(). Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-02Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queueDavid S. Miller3-14/+33
Jeff Kirsher says: ==================== Intel Wired LAN Driver Fixes 2019-04-01 This series contains two fixes for XDP in the i40e driver. Björn provides both fixes, first moving a function out of the header and into the main.c file. Second fixes a regression introduced in an earlier patch that removed umem from the VSI. This caused an issue because the setup code would try to enable AF_XDP zero copy unconditionally, as long as there was a umem placed in the netdev receive structure. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-01nfp: flower: remove vlan CFI bit from push vlan actionPieter Jansen van Vuuren2-3/+1
We no longer set CFI when pushing vlan tags, therefore we remove the CFI bit from push vlan. Fixes: 1a1e586f54bf ("nfp: add basic action capabilities to flower offloads") Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Signed-off-by: Louis Peens <louis.peens@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-01nfp: flower: replace CFI with vlan presentPieter Jansen van Vuuren2-15/+14
Replace vlan CFI bit with a vlan present bit that indicates the presence of a vlan tag. Previously the driver incorrectly assumed that an vlan id of 0 is not matchable, therefore we indicate vlan presence with a vlan present bit. Fixes: 5571e8c9f241 ("nfp: extend flower matching capabilities") Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com> Signed-off-by: Louis Peens <louis.peens@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-01i40e: add tracking of AF_XDP ZC state for each queue pairBjörn Töpel3-1/+14
In commit f3fef2b6e1cc ("i40e: Remove umem from VSI") a regression was introduced; When the VSI was reset, the setup code would try to enable AF_XDP ZC unconditionally (as long as there was a umem placed in the netdev._rx struct). Here, we add a bitmap to the VSI that tracks if a certain queue pair has been "zero-copy enabled" via the ndo_bpf. The bitmap is used in i40e_xsk_umem, and enables zero-copy if and only if XDP is enabled, the corresponding qid in the bitmap is set and the umem is non-NULL. Fixes: f3fef2b6e1cc ("i40e: Remove umem from VSI") Signed-off-by: Björn Töpel <bjorn.topel@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-04-01i40e: move i40e_xsk_umem functionBjörn Töpel2-14/+20
The i40e_xsk_umem function was explicitly inlined in i40e.h. There is no reason for that, so move it to i40e_main.c instead. Signed-off-by: Björn Töpel <bjorn.topel@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-03-31net: stmmac: don't log oversized framesAaro Koskinen1-2/+0
This is log is harmful as it can trigger multiple times per packet. Delete it. Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-31net: stmmac: fix dropping of multi-descriptor RX framesAaro Koskinen1-0/+5
Packets without the last descriptor set should be dropped early. If we receive a frame larger than the DMA buffer, the HW will continue using the next descriptor. Driver mistakes these as individual frames, and sometimes a truncated frame (without the LD set) may look like a valid packet. This fixes a strange issue where the system replies to 4098-byte ping although the MTU/DMA buffer size is set to 4096, and yet at the same time it's logging an oversized packet. Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-31net: stmmac: don't overwrite discard_frame statusAaro Koskinen1-3/+4
If we have error bits set, the discard_frame status will get overwritten by checksum bit checks, which might set the status back to good one. Fix by checking the COE status only if the frame is good. Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-31net: stmmac: don't stop NAPI processing when dropping a packetAaro Koskinen1-7/+7
Currently, if we drop a packet, we exit from NAPI loop before the budget is consumed. In some situations this will make the RX processing stall e.g. when flood pinging the system with oversized packets, as the errorneous packets are not dropped efficiently. If we drop a packet, we should just continue to the next one as long as the budget allows. Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-31net: stmmac: ratelimit RX error logsAaro Koskinen1-6/+8
Ratelimit RX error logs. Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-31net: stmmac: use correct DMA buffer size in the RX descriptorAaro Koskinen7-19/+35
We always program the maximum DMA buffer size into the receive descriptor, although the allocated size may be less. E.g. with the default MTU size we allocate only 1536 bytes. If somebody sends us a bigger frame, then memory may get corrupted. Fix by using exact buffer sizes. Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-30r8169: disable default rx interrupt coalescing on RTL8168Heiner Kallweit1-1/+1
It was reported that re-introducing ASPM, in combination with RX interrupt coalescing, results in significantly increased packet latency, see [0]. Disabling ASPM or RX interrupt coalescing fixes the issue. Therefore change the driver's default to disable RX interrupt coalescing. Users still have the option to enable RX coalescing via ethtool. [0] https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=925496 Fixes: a99790bf5c7f ("r8169: Reinstate ASPM Support") Reported-by: Mike Crowe <mac@mcrowe.com> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-30Merge tag 'iwlwifi-for-kalle-2019-03-22' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixesKalle Valo14-146/+54
First batch of iwlwifi fixes intended for v5.1 * add some new PCI IDs (plus a struct name change they depend on); * fix crypto with new devices, namely 22560 and above; * a bunch of fixes (and a dependency) for the new debugging infra;
2019-03-29Merge tag 'mlx5-fixes-2019-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linuxDavid S. Miller9-81/+152
Saeed Mahameed says: ==================== Mellanox, mlx5 fixes 2019-03-29 This series introduces some fixes to mlx5 driver. Please pull and let me know if there is any problem. For -stable v4.11 ('net/mlx5: Decrease default mr cache size') For -stable v4.12 ('net/mlx5e: Add a lock on tir list') For -stable v4.13 ('net/mlx5e: Fix error handling when refreshing TIRs') For -stable v4.18 ('net/mlx5e: Update xon formula') For -stable v4.19 ('net: mlx5: Add a missing check on idr_find, free buf') ('net/mlx5e: Update xoff formula') net-next merge Note: When merged with net-next the following simple conflict will appear, drivers/net/ethernet/mellanox/mlx5/core/en/port_buffer.c ++<<<<<<< HEAD (net) + * max_mtu: netdev's max_mtu ++======= + * @mtu: device's MTU ++>>>>>>> net-next To resolve: just replace the line in net-next * @mtu: device's MTU to * @max_mtu: netdev's max_mtu ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-29Revert "cxgb4: Update 1.23.3.0 as the latest firmware supported."David S. Miller1-6/+6
This reverts commit 4d31c4fa3f9ef7b7e2e79fd57d21290f64c938f5. Accidently applied this to the wrong tree. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-29cxgb4: Update 1.23.3.0 as the latest firmware supported.Vishal Kulkarni1-6/+6
Change t4fw_version.h to update latest firmware version number to 1.23.3.0. Signed-off-by: Vishal Kulkarni <vishal@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-29hv_netvsc: Fix unwanted wakeup after tx_disableHaiyang Zhang3-8/+31
After queue stopped, the wakeup mechanism may wake it up again when ring buffer usage is lower than a threshold. This may cause send path panic on NULL pointer when we stopped all tx queues in netvsc_detach and start removing the netvsc device. This patch fix it by adding a tx_disable flag to prevent unwanted queue wakeup. Fixes: 7b2ee50c0cd5 ("hv_netvsc: common detach logic") Reported-by: Mohammed Gamal <mgamal@redhat.com> Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-29bonding: show full hw address in sysfs for slave entriesKonstantin Khorenko1-1/+3
Bond expects ethernet hwaddr for its slave, but it can be longer than 6 bytes - infiniband interface for example. # cat /sys/devices/<skipped>/net/ib0/address 80:00:02:08:fe:80:00:00:00:00:00:00:7c:fe:90:03:00:be:5d:e1 # cat /sys/devices/<skipped>/net/ib0/bonding_slave/perm_hwaddr 80:00:02:08:fe:80 So print full hwaddr in sysfs "bonding_slave/perm_hwaddr" as well. Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-29net/mlx5e: Consider tunnel type for encap contextsEli Britstein1-9/+19
The driver allocates an encap context based on the tunnel properties, and reuse that context for all flows using the same tunnel properties. Commit df2ef3bff193 ("net/mlx5e: Add GRE protocol offloading") introduced another tunnel protocol other than the single VXLAN previously supported. A flow that uses a tunnel with the same tunnel properties but with a different tunnel type (GRE vs VXLAN for example) would mistakenly reuse the previous alocated context, causing the traffic to be sent with the wrong encapsulation. Fix that by considering the tunnel type for encap contexts. Fixes: df2ef3bff193 ("net/mlx5e: Add GRE protocol offloading") Signed-off-by: Eli Britstein <elibr@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-03-29net/mlx5e: Update xon formulaHuy Nguyen1-12/+16
Set xon = xoff - netdev's max_mtu. netdev's max_mtu will give enough time for the pause frame to arrive at the sender. Fixes: 0696d60853d5 ("net/mlx5e: Receive buffer configuration") Signed-off-by: Huy Nguyen <huyn@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-03-29net/mlx5e: Update xoff formulaHuy Nguyen1-5/+6
Set minimum speed in xoff threshold formula to 40Gbps Fixes: 0696d60853d5 ("net/mlx5e: Receive buffer configuration") Signed-off-by: Huy Nguyen <huyn@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-03-29net/mlx5: E-Switch, fix syndrome (0x678139) when turn on vepaHuy Nguyen1-0/+1
Make sure the struct mlx5_flow_destination is zero before filling in the field. Fixes: 8da202b24913 ("net/mlx5: E-Switch, Add support for VEPA in legacy mode.") Signed-off-by: Huy Nguyen <huyn@mellanox.com> Reviewed-by: Daniel Jurgens <danielj@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-03-29net/mlx5: E-Switch, Fix esw manager vport indication for more vport commandsOmri Kahalon1-4/+2
Traditionally, the PF (Physical Function) which resides on vport 0 was the E-switch manager. Since the ECPF (Embedded CPU Physical Function), which resides on vport 0xfffe, was introduced as the E-Switch manager, the assumption that the E-switch manager is on vport 0 is incorrect. Since the eswitch code already uses the actual vport value, all we need is to always set other_vport=1. Signed-off-by: Omri Kahalon <omrik@mellanox.com> Reviewed-by: Max Gurtovoy <maxg@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-03-29net/mlx5: E-Switch, Protect from invalid memory access in offload fdb tableRoi Dayan1-0/+1
The esw offloads structures share a union with the legacy mode structs. Reset the offloads struct to zero in init to protect from null assumptions made by the legacy mode code. Signed-off-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-03-29net/mlx5e: Correctly use the namespace type when allocating pedit actionTonghao Zhang1-1/+1
The capacity of FDB offloading and NIC offloading table are different, and when allocating the pedit actions, we should use the correct namespace type. Fixes: c500c86b0c75d ("net/mlx5e: support for two independent packet edit actions") Cc: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Acked-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-03-29net/mlx5: E-Switch, Fix access to invalid memory when toggling esw modesRoi Dayan1-0/+2
The esw fdb table has a union of legacy and offloads members. So if we were in a certain esw mode we could set some memebers and not set null which is fine as on destroy path and don't care. But then moving from legacy to switchdev a second time, the cleanup flow of legacy mode checks if a struct member was in use if it's not null so we need to make sure to reset the code to null when we init legacy mode. Fixes: 8da202b24913 ("net/mlx5: E-Switch, Add support for VEPA in legacy mode.") Signed-off-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Huy Nguyen <huyn@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-03-29net/mlx5: ethtool, Allow legacy link-modes configuration via non-extended ptysAya Levin2-19/+31
Allow configuration of legacy link-modes even when extended link-modes are supported. This requires reading of legacy advertisement even when extended link-modes are supported. Since legacy and extended advertisement are mutually excluded, wait for empty reply from extended advertisement before reading legacy advertisement. Fixes: 6a897372417e ("net/mlx5: ethtool, Add ethtool support for 50Gbps per lane link modes") Signed-off-by: Aya Levin <ayal@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-03-29net/mlx5: ethtool, Fix type analysis of advertised link-modeAya Levin1-2/+3
Ethtool option set_link_ksettings allows setting of legacy link-modes or extended link-modes. Refine the decision of which type of link-modes is set. Fixes: 6a897372417e ("net/mlx5: ethtool, Add ethtool support for 50Gbps per lane link modes") Signed-off-by: Aya Levin <ayal@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-03-29net/mlx5e: Add a lock on tir listYuval Avnery1-0/+7
Refresh tirs is looping over a global list of tirs while netdevs are adding and removing tirs from that list. That is why a lock is required. Fixes: 724b2aa15126 ("net/mlx5e: TIRs management refactoring") Signed-off-by: Yuval Avnery <yuvalav@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-03-29net: mlx5: Add a missing check on idr_find, free bufAditya Pakki1-3/+11
idr_find() can return a NULL value to 'flow' which is used without a check. The patch adds a check to avoid potential NULL pointer dereference. In case of mlx5_fpga_sbu_conn_sendmsg() failure, free buf allocated using kzalloc. Fixes: ab412e1dd7db ("net/mlx5: Accel, add TLS rx offload routines") Signed-off-by: Aditya Pakki <pakki001@umn.edu> Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-03-29net/mlx5e: Allow IPv4 ttl & IPv6 hop_limit rewrite for all L4 protocolsDmytro Linkin1-4/+48
For some protocols we are not allowing IP header rewrite offload, since the HW is not capable to properly adjust the l4 checksum. However, TTL & HOPLIMIT modification can be done for all IP protocols, because they are not part of the pseudo header taken into account for checksum. Fixes: 738678817573 ("drivers: net: use flow action infrastructure") Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-03-29net/mlx5e: Fix error handling when refreshing TIRsGavi Teitz1-2/+4
Previously, a false positive would be caught if the TIRs list is empty, since the err value was initialized to -ENOMEM, and was only updated if a TIR is refreshed. This is resolved by initializing the err value to zero. Fixes: b676f653896a ("net/mlx5e: Refactor refresh TIRs") Signed-off-by: Gavi Teitz <gavi@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-03-29net/mlx5: Decrease default mr cache sizeArtemy Kovalyov1-20/+0
Delete initialization of high order entries in mr cache to decrease initial memory footprint. When required, the administrator can populate the entries with memory keys via the /sys interface. This approach is very helpful to significantly reduce the per HW function memory footprint in virtualization environments such as SRIOV. Fixes: 9603b61de1ee ("mlx5: Move pci device handling from mlx5_ib to mlx5_core") Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com> Signed-off-by: Moni Shoua <monis@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Reported-by: Shalom Toledo <shalomt@mellanox.com> Acked-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-03-28nfp: disable netpoll on representorsJakub Kicinski1-1/+1
NFP reprs are software device on top of the PF's vNIC. The comment above __dev_queue_xmit() sayeth: When calling this method, interrupts MUST be enabled. This is because the BH enable code must have IRQs enabled so that it will not deadlock. For netconsole we can't guarantee IRQ state, let's just disable netpoll on representors to be on the safe side. When the initial implementation of NFP reprs was added by the commit 5de73ee46704 ("nfp: general representor implementation") .ndo_poll_controller was required for netpoll to be enabled. Fixes: ac3d9dd034e5 ("netpoll: make ndo_poll_controller() optional") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-28nfp: validate the return code from dev_queue_xmit()Jakub Kicinski1-1/+1
dev_queue_xmit() may return error codes as well as netdev_tx_t, and it always consumes the skb. Make sure we always return a correct netdev_tx_t value. Fixes: eadfa4c3be99 ("nfp: add stats and xmit helpers for representors") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-28qmi_wwan: add Olicard 600Bjørn Mork1-0/+1
This is a Qualcomm based device with a QMI function on interface 4. It is mode switched from 2020:2030 using a standard eject message. T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2020 ProdID=2031 Rev= 2.32 S: Manufacturer=Mobile Connect S: Product=Mobile Connect S: SerialNumber=0123456789ABCDEF C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none) E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-28Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queueDavid S. Miller6-60/+25
Jeff Kirsher says: ==================== Intel Wired LAN Driver Fixes 2019-03-26 This series contains updates to igb, ixgbe, i40e and fm10k. Jake fixes an issue with PTP in i40e where a previous commit resulted in a regression where the driver would interpret small negative adjustments as large positive additions, resulting in incorrect behavior. Arvind Sankar fixes an issue in igb where a previous commit would cause a warning in the PCI pm core and resulted in pci_pm_runtime_suspend would not call pci_save_state or pci_finish_runtime_suspend. Ivan Vecera fixes MDIO bus registration with ixgbe, where the driver was ignoring errors returned when registering and would leave the pointer in a NULL state which triggered a BUG when un-registering. Stefan Assmann fixes the check for Wake-On-LAN for i40e, which only supports magic packet. Yue Haibing fixes a potential NULL pointer de-reference in fm10k by adding a simple check if the value is NULL. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.