| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The xgene_mac_ops and xgene_port_ops structures are never modified, so
declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Kalle Vallo says:
====================
brcfmac
* support bcm4359 which can operate in two bands concurrently
* disable runtime pm for USB avoiding issues
* use generic pm callback in PCIe driver
* support wowlan wake indication reporting
* add beamforming support
* unified handling of firmware files
ath10k
* support Manegement Frame Protection (MFP)
* add thermal throttling support for 10.4 firmware
* add support for pktlog in QCA99X0
* add debugfs file to enable Bluetooth coexistence feature
* use firmware's native mesh interface type instead of raw mode
iwlwifi
* BT coex improvements
* D3 operation bugfixes
* rate control improvements
* firmware debugging infra improvements
* ground work for multi Rx
* various security fixes
====================
Conflicts:
drivers/net/wireless/ath/ath10k/pci.c
The conflict resolution at:
http://article.gmane.org/gmane.linux.kernel.next/37391
by Stephen Rothwell was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
the simple_strtoul function is obsolete. This patch replace it by
kstrtox.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Johannes Berg says:
====================
This pull request got a bit bigger than I wanted, due to
needing to reshuffle and fix some bugs. I merged mac80211
to get the right base for some of these changes.
* new mac80211 API for upcoming driver changes: EOSP handling,
key iteration
* scan abort changes allowing to cancel an ongoing scan
* VHT IBSS 80+80 MHz support
* re-enable full AP client state tracking after fixes
* various small fixes (that weren't relevant for mac80211)
* various cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since we have moved on to using allocated pages to carve receive
buffers instead of netdev_alloc_skb() there is no need to store
any pointers for later retrieval. Earlier we had to store
skb and skb->data pointers which later are used to handover
received packet to network stack.
This will avoid an unnecessary cache miss as well.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The same switch-case repeates for nivc_*_intr functions.
In this patch it is moved to a helper nicvf_int_type_to_mask().
By the way:
- Unneeded write to NICVF register dropped if int_type is unknown.
- netdev_dbg() is used instead of netdev_err().
Signed-off-by: Yury Norov <yury.norov@auriga.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Acked-by: Vadim Lomovtsev <Vadim.Lomovtsev@caiumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Device tree properties for a phy device are expected to be in the phy
node. The current code for the DP83867 also tries to look in the
parent node. The devices binding documentation does not mention this,
no current device tree file makes use of this, and it is not behaviour
we want. So remove looking in the parent device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding a writable sysfs attribute for the "NDP to end"
quirk flag.
This makes it easier for end users to test new devices for
this firmware bug. We've been lucky so far, but we should
not depend on reporters capable of rebuilding the driver.
Cc: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the mlx4 driver runs in HA mode, and all VFs are single ported
ones, we make their single port Highly-Available.
This is done by taking advantage of the HA mode properties (following
bonding changes with programming the port V2P map, etc) and adding
the missing parts which are unique to SRIOV such as mirroring VF
steering rules on both ports.
Due to limits on the MAC and VLAN table this mode is enabled only when
number of total VFs is under 64.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to HW limitations, indexes to MAC and VLAN tables are always taken
from the table of the actual port. So, if a resource holds an index to
a table, it may refer to different values during the lifetime of the
resource, unless the tables are mirrored. Also, even when
driver is not in HA mode the policy of allocating an index to these
tables is such to make sure, as much as possible, that when the time
comes the mirroring will be successful. This means that in multifunction
mode the allocation of a free index in a port's table tries to make sure
that the same index in the other's port table is also free.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under HA mode, steering rules set by VFs should be mirrored on both
ports of the device so packets will be accepted no matter on which
port they arrived.
Since getting into HA mode is done dynamically when the user bonds mlx4
Ethernet netdevs, we keep hold of the VF DMFS rule mbox with the port
value flipped (1->2,2->1) and execute the mirroring when getting into
HA mode. Later, when going out of HA mode, we unset the mirrored rules.
In that context note that mirrored rules cannot be removed explicitly.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under HA mode, the link down event should be sent to VFs only if both
ports are down.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In HA mode, the link state for VFs for which the policy is "auto"
(i.e. follow the physical link state) should be ORed from both ports.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The notifier calls were thrown in as a last-minute fix for an
imagined "this device could be part of a bridge" problem. That
revealed a certain lack of locking. Not to mention testing...
Avoid this splat:
RTNL: assertion failed at net/core/dev.c (1639)
CPU: 0 PID: 4293 Comm: bash Not tainted 4.4.0-rc3+ #358
Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011
0000000000000000 ffff8800ad253d60 ffffffff8122f7cf ffff8800ad253d98
ffff8800ad253d88 ffffffff813833ab 0000000000000002 ffff880230f48560
ffff880230a12900 ffff8800ad253da0 ffffffff813833da 0000000000000002
Call Trace:
[<ffffffff8122f7cf>] dump_stack+0x4b/0x63
[<ffffffff813833ab>] call_netdevice_notifiers_info+0x3d/0x59
[<ffffffff813833da>] call_netdevice_notifiers+0x13/0x15
[<ffffffffa09be227>] raw_ip_store+0x81/0x193 [qmi_wwan]
[<ffffffff8131e149>] dev_attr_store+0x20/0x22
[<ffffffff811d858b>] sysfs_kf_write+0x49/0x50
[<ffffffff811d8027>] kernfs_fop_write+0x10a/0x151
[<ffffffff8117249a>] __vfs_write+0x26/0xa5
[<ffffffff81085ed4>] ? percpu_down_read+0x53/0x7f
[<ffffffff81174c9e>] ? __sb_start_write+0x5f/0xb0
[<ffffffff81174c9e>] ? __sb_start_write+0x5f/0xb0
[<ffffffff81172c37>] vfs_write+0xa3/0xe7
[<ffffffff811734ad>] SyS_write+0x50/0x7e
[<ffffffff8145c517>] entry_SYSCALL_64_fastpath+0x12/0x6f
Fixes: 32f7adf633b9 ("net: qmi_wwan: support "raw IP" mode")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 8fe269991aece394a7ed274f525d96c73f94109a.
The case where VXLAN is a module and i40e driver is inbuilt
will not be handled properly with this change since i40e
will have an undefined symbol vxlan_get_rx_port in it.
v2: Add a signed-off-by.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The current default ITR for Tx is overly restrictive. Using a simple
netperf TCP_STREAM test, we top out at about 10Gb/s for a single thread
when running using 1500 byte frames. By reducing the ITR value to 25usec
(up to 40K interrupts a second from 10K), we are able to achieve 36Gb/s
for a single thread TCP stream test.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The existing adaptive ITR algorithm is overly restrictive. It throttles
incorrectly for various traffic rates, and does not produce good
performance. The algorithm now allows for more interrupts per second,
and does some calculation to help improve for smaller packet loads. In
addition, take into account the new itr_scale from the hardware which
indicates how much to scale due to PCIe link speed.
Reported-by: Matthew Vick <matthew.vick@intel.com>
Reported-by: Alex Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Define a macro for identifying when the itr value is dynamic or
adaptive. The concept was taken from i40e. This helps make clear what
the check is, and reduces the line length to something more reasonable
in a few places.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The Intel Ethernet Switch FM10000 Host Interface interrupt throttle
timers are based on the PCIe link speed. Because of this, the value
being programmed into the ITR registers must be scaled accordingly.
For the PF, this is as simple as reading the PCIe link speed and storing
the result. However, in the case of SR-IOV, the VF's interrupt throttle
timers are based on the link speed of the PF. However, the VF is unable
to get the link speed information from its configuration space, so the
PF must inform it of what scale to use.
Rather than pass this scale via mailbox message, take advantage of
unused bits in the TDLEN register to pass the scale. It is the
responsibility of the PF to program this for the VF while setting up the
VF queues and the responsibility of the VF to get the information
accordingly. This is preferable because it allows the VF to set up the
interrupts properly during initialization and matches how the MAC
address is passed in the TDBAL/TDBAH registers.
Since we're modifying fm10k_type.h, we may as well also update the
copyright year.
Reported-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Originally this statistic was renamed because the method of dropping was
called "drop_oversized_messages", but this logic has changed much, and
this counter does actually represent messages which we failed to
transmit for a number of reasons. Rename the counter back to tx_dropped
since this is when it will increment, and it is less confusing.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
A previous bug was uncovered by addition of a debug stat to indicate the
actual number of DWORDS we pulled from the mbmem. It turned out this was
not the same as the tx_dwords counter. While the previous bug fix should
have corrected this in all cases, add some debug stats that count the
number of DWORDs pushed or pulled from the mbmem. A future debugger may
take advantage of this statistic for debugging purposes. Since we're
modifying fm10k_mbx.h, update the copyright year as well.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Since the resultant data type of the mac_update.mac_upper field is u16,
it does not make sense to typecast u8 variables to u32 first. Since
we're modifying fm10k_pf.c, also update the copyright year.
Reported-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The init_hw function may fail, and in the case of VFs, it might change
the number of maximum queues available. Thus, for every flow which
checks init_hw, we need to ensure that we clear the queue scheme before,
and initialize it after. The fm10k_io_slot_reset path will end up
triggering a reset so fm10k_reinit needs this change. The
fm10k_io_error_detected and fm10k_io_resume also need to properly clear
and reinitialize the queue scheme.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
A recent change modified init_hw in some flows the function may fail on
VF devices. For example, if a VF doesn't yet own its own queues.
However, many callers of init_hw didn't bother to check the error code.
Other callers checked but only displayed diagnostic messages without
actually handling the consequences.
Fix this by (a) always returning and preventing the netdevice from going
up, and (b) printing the diagnostic in every flow for consistency. This
should resolve an issue where VF drivers would attempt to come up
before the PF has finished assigning queues.
In addition, change the dmesg output to explicitly show the actual
function that failed, instead of combining reset_hw and init_hw into a
single check, to help for future debugging.
Fixes: 1d568b0f6424 ("fm10k: do not assume VF always has 1 queue")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
VF drivers must detect how many queues are available. Previously, the
driver assumed that each VF has at minimum 1 queue. This assumption is
incorrect, since it is possible that the PF has not yet assigned the
queues to the VF by the time the VF checks. To resolve this, we added a
check first to ensure that the first queue is infact owned by the VF at
init_hw_vf time. However, the code flow did not reset hw->mac.max_queues
to 0. In some cases, such as during reinit flows, we call init_hw_vf
without clearing the previous value of hw->mac.max_queues. Due to this,
when init_hw_vf errors out, if its error code is not properly handled
the VF driver may still believe it has queues which no longer belong to
it. Fix this by clearing the hw->mac.max_queues on exit due to errors.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Don't change netdev hw_features later in fm10k_probe, instead set all
values inside fm10k_alloc_netdev. To do so, we need to know the MAC type
(whether it is PF or VF) in order to determine what to do. This helps
ensure that all logic regarding features is co-located.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The code reading the MAHR/MALR registers in read_mac_address() is terribly
ineffective -- it reads MAHR 4 times and MALR 2 times, while it's enough to
read each register only once. Use the local variables to achieve that,
somewhat beautifying the code while at it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code reading the MAHR/MALR registers in ravb_read_mac_address() is
terribly ineffective -- it reads MAHR 4 times and MALR 2 times, while
it's enough to read each register only once. Use the local variables to
achieve that, somewhat beautifying the code while at it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 'flags' field in bnx2x_stats_arr[] serves only one purpose - to tell
us if the statistic is a per-port stat and thus should not be shown for
virtual functions. It's strange that the field can have three different
values. A boolean will do just fine.
Also remove IS_FUNC_STAT(). It was used only once and it's in fact just
a negation of IS_PORT_STAT().
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's supposed to be impossible for TPA to give us anything else
than IPv4 or IPv6 here. But in case there is a way to reach this error
by some strange received frames, we don't want to flood the kernel log.
WARN_ONCE is better for this purpose.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
alloc_pages() already prints a warning when it fails. No need to emit
another message. Certainly not at KERN_ERR level, because it is no big
deal if this GFP_ATOMIC allocation fails occasionally.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A change in MCFW behaviour means that the net driver must update its record
of the warm_boot_count by reading it from the ER_DZ_BIU_MC_SFT_STATUS
register.
On v4.6.x MCFW the global boot count was incremented when some functions
needed to be reset to enable multicast chaining, so all functions saw the
same value. In that case, the driver needed to increment its
warm_boot_count when other functions were reset, to avoid noticing it later
and then trying to reset itself to recover unnecessarily.
With v4.7+ MCFW, the boot count in firmware doesn't change as that is
unnecessary since the PFs that have been reset will each receive an MC
reboot notification. In that case, the driver re-reads the unchanged
value.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An HDLC device can change type when the protocol driver is changed.
Calling the notifier change allows potential users of the interface
know about this planned change, and even block it. After the change
has occurred, send a second notification to users can evaluate the new
device type etc.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current code first unregisters the device, and then detaches the
protocol from it. This should be performed the other way around, since
the detach may try to use state which has been freed by the
unregister. Swap the order, so that we first detach and then remove the
netdev.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
QMI wwan devices have traditionally emulated ethernet devices
by default. But they have always had the capability of operating
without any L2 header at all, transmitting and receiving "raw"
IP packets over the USB link. This firmware feature used to be
configurable through the QMI management protocol.
Traditionally there was no way to verify the firmware mode
without attempting to change it. And the firmware would often
disallow changes anyway, i.e. due to a session already being
established. In some cases, this could be a hidden firmware
internal session, completely outside host control. For these
reasons, sticking with the "well known" default mode was safest.
But newer generations of QMI hardware and firmware have moved
towards defaulting to "raw IP" mode instead, followed by an
increasing number of bugs in the already buggy "802.3" firmware
implementation. At the same time, the QMI management protocol
gained the ability to detect the current mode. This has enabled
the userspace QMI management application to verify the current
firmware mode without trying to modify it.
Following this development, the latest QMI hardware and firmware
(the MDM9x30 generation) has dropped support for "802.3" mode
entirely. Support for "raw IP" framing in the driver is therefore
necessary for these devices, and to a certain degree to work
around problems with the previous generation,
This patch adds support for "raw IP" framing for QMI devices,
changing the netdev from an ethernet device to an ARPHRD_NONE
p-t-p device when "raw IP" framing is enabled.
The firmware setup is fully delegated to the QMI userspace
management application, through simple tunneling of the QMI
protocol. The driver will therefore not know which mode has been
"negotiated" between firmware and userspace. Allowing userspace
to inform the driver of the result through a sysfs switch is
considered a better alternative than to change the well established
clean delegation of firmware management to userspace.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Assume the minidriver has taken care of all L2 header parsing
if it sets skb->protocol. This allows the minidriver to
support non-ethernet L2 headers, and even operate without
any L2 header at all.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This turned out to be a bootloader device ID. No need for
that in this driver. It will only provide a single serial
function.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MDM9x30 based modems appear to go into a deeper sleep when
suspended without "Remote Wakeup" enabled. The QMI interface
will not respond unless a "set DTR" control request is sent
on resume. The effect is similar to a QMI_CTL SYNC request,
resetting (some of) the firmware state.
We allow userspace sessions to span multiple character device
open/close sequences. This means that userspace can depend
on firmware state while both the netdev and the character
device are closed. We have disabled "needs_remote_wakeup" at
this point to allow devices without remote wakeup support to
be auto-suspended.
To make sure the MDM9x30 keeps firmware state, we need to
keep "needs_remote_wakeup" always set. We also need to
issue a "set DTR" request to enable the QMI interface.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the initializzation code to disable the hardware
vlan support for VLAN Tag stripping by default for now.
Proper support of "hardware VLAN assitance" feature would
soon come in the next coming patches.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the support of ethtool TSO option to support
Hip06 SoC to HNS
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lisheng <lisheng011@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the support of "TSO (TCP Segment Offload)" feature
provided by the Hip06 ethernet hardware to the HNS ethernet
driver.
Enabling this feature would help offload the TCP Segmentation
process to the Hip06 ethernet hardware. This eventually would help
in saving precious cpu cycles.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lisheng <lisheng011@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the support of "RSS (Receive Side Scaling)" feature
provided by the Hip06 ethernet hardware to the HNS ethernet
driver.
This feature helps in distributing the different flows (mapped as
hash by hardware using Toeplitz Hash) to different Queues asssociated
with the processor cores. The mapping of flow-hash values to the
different queues is stored in indirection table (which is per Packet-
parse-Engine/PPE). This patch also provides the changes to re-program
the (flow-hash<->Qid) mapping using the ethtool.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Reviewed-by: Kenneth Lee <liguozhu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patchset adds support of Hisilicon Hip06 SoC to the existing HNS
ethernet driver.
The changes in the driver are mainly due to changes in the DMA
descriptor provided by the Hip06 ethernet hardware. These changes
need to co-exist with already present Hip05 DMA descriptor and its
operating functions. The decision to choose the correct type of DMA
descriptor is taken dynamically depending upon the version of the
hardware (i.e. V1/hip05 or V2/hip06, see already existing
hisilicon-hns-nic.txt binding file for detailed description). other
changes includes in SBM, DSAF and PPE modules as well. Changes
affecting the driver related to the newly added ethernet hardware
features in Hip06 would be added as separate patch over this and
subsequent patches.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: lisheng <lisheng011@huawei.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a packet is received from netlink with the frequency value set it is
checked against the current radio's frequency and discarded if different.
The frequency is also checked against data2->tmp_chan to support the "hw"
off-channel/scan case.
Signed-off-by: Adam Welle <arwelle@cert.org>
[allow both simultaneously, add locking]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If the rate control algorithm messed up then the txrate pointer
here could be NULL - WARN and drop the packet from monitoring.
Signed-off-by: Amit Khatri <amit.khatri@samsung.com>
Signed-off-by: Rahul Jain <rahul.jain@samsung.com>
[rewrite commit message, add warning]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Instead of using pointers, use sequentially assigned cookies.
This is easier to understand while debugging and also avoids
problems when the pointer is reused for the next allocation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
Julia Lawall
David S. Miller
LABBE Corentin
Sunil Goutham
Yury Norov
Andrew Lunn
Bjørn Mork
Moni Shoua
Or Gerlitz
Singhai, Anjali
Jacob Keller
Sergei Shtylyov
Michal Schmidt
Daniel Pieczko
Salil
Adam Welle
Amit Khatri
Johannes Berg