| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Both PCLK and HCLK are "required" clocks according to macb devicetree
documentation. There is a chance that devm_clk_get doesn't return a
negative error but just a NULL clock structure instead. In such a case
the driver proceeds as usual and uses pclk value 0 to calculate MDC
divisor which is incorrect. Hence fix the same in clock initialization.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the DP83825I ethernet PHY to the DP83822 driver.
These devices share the same WoL register bits and addresses.
The phy_driver init was made into a macro as there may be future
devices appended to this driver that will share the register space.
http://www.ti.com/lit/gpn/dp83825i
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure we don't try to enqueue XDP_REDIRECT frames to an
inexistent FQ.
While it is guaranteed not to have more than one queue per core,
having fewer queues than CPUs on an interface is a valid
configuration.
Fixes: d678be1dc1ec ("dpaa2-eth: add XDP_REDIRECT support")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ks8851 chip is sold either with an SPI interface (KSZ8851SNL) or
with a so-called non-PCI interface (KSZ8851-16MLL). When the driver
for the latter was introduced with commit a55c0a0ed415 ("drivers/net:
ks8851_mll ethernet network driver"), it duplicated the register macros
introduced by the driver for the former with commit 3ba81f3ece3c ("net:
Micrel KS8851 SPI network driver").
The chips are almost identical, so the duplication seems unwarranted.
There are a handful of bits which are in use on the KSZ8851-16MLL but
reserved on the KSZ8851SNL, and vice-versa, but there are no actual
collisions.
Thus, remove the duplicate definitions from the KSZ8851-16MLL driver.
Mark all bits which differ between the two chips. Move the SPI frame
opcodes, which are specific to KSZ8851SNL, to its driver.
The KSZ8851-16MLL driver added a RXFCTR_THRESHOLD_MASK macro which is a
duplication of the RXFCTR_RXFCT_MASK macro, rename it where it's used.
Same for P1MBCR_FORCE_FDX, which duplicates the BMCR_FULLDPLX macro and
OBCR_ODS_16MA, which duplicates OBCR_ODS_16mA.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the header file accompanying the ks8851 driver, the P1SCLMD register
macros are misnamed, they actually pertain to the P1CR register.
The P1CR macros in turn pertain to the P1SR register, see pages 65 to 68
of the spec:
http://www.hqchip.com/uploads/pdf/201703/47c98946d6c97a4766e14db3f24955f2.pdf
The misnomers have no negative consequences so far because the macros
aren't used by ks8851.c, but that's about to change.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ks8851 chip's initial carrier state is down. A Link Change Interrupt
is signaled once interrupts are enabled if the carrier is up.
The ks8851 driver has it backwards by assuming that the initial carrier
state is up. The state is therefore misrepresented if the interface is
opened with no cable attached. Fix it.
The Link Change interrupt is sometimes not signaled unless the P1MBSR
register (which contains the Link Status bit) is read on ->ndo_open().
This might be a hardware erratum. Read the register by calling
mii_check_link(), which has the desirable side effect of setting the
carrier state to down if the cable was detached while the interface was
closed.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ks8851 driver currently requests the IRQ before registering the
net_device. Because the net_device name is used as IRQ name and is
still "eth%d" when the IRQ is requested, it's impossibe to tell IRQs
apart if multiple ks8851 chips are present. Most other drivers delay
requesting the IRQ until the net_device is opened. Do the same.
The driver doesn't enable interrupts on the chip before opening the
net_device and disables them when closing it, so there doesn't seem to
be a need to request the IRQ already on probe.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 73fdeb82e963 ("net: ks8851: Add optional vdd_io regulator and
reset gpio") amended the ks8851 driver to briefly assert the chip's
reset pin on probe. It also amended the probe routine's error path to
reassert the reset pin if a subsequent initialization step fails.
However the commit misplaced reassertion of the reset pin in the error
path such that it is not performed if the check of the Chip ID and
Enable Register (CIDER) fails. The error path is therefore slightly
asymmetrical to the probe routine's body. Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ks8851 driver lets the chip auto-dequeue received packets once they
have been read in full. It achieves that by setting the ADRFE flag in
the RXQCR register ("Auto-Dequeue RXQ Frame Enable").
However if allocation of a packet's socket buffer or retrieval of the
packet over the SPI bus fails, the packet will not have been read in
full and is not auto-dequeued. Such partial retrieval of a packet
confuses the chip's RX queue management: On the next RX interrupt,
the first packet read from the queue will be the one left there
previously and this one can be retrieved without issues. But for any
newly received packets, the frame header status and byte count registers
(RXFHSR and RXFHBCR) contain bogus values, preventing their retrieval.
The chip allows explicitly dequeueing a packet from the RX queue by
setting the RRXEF flag in the RXQCR register ("Release RX Error Frame").
This could be used to dequeue the packet in case of an error, but if
that error is a failed SPI transfer, it is unknown if the packet was
transferred in full and was auto-dequeued or if it was only transferred
in part and requires an explicit dequeue. The safest approach is thus
to always dequeue packets explicitly and forgo auto-dequeueing.
Without this change, I've witnessed packet retrieval break completely
when an SPI DMA transfer fails, requiring a chip reset. Explicit
dequeueing magically fixes this and makes packet retrieval absolutely
robust for me.
The chip's documentation suggests auto-dequeuing and uses the RRXEF
flag only to dequeue error frames which the driver doesn't want to
retrieve. But that seems to be a fair-weather approach.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
clang points out a harmless signed integer overflow:
drivers/net/ethernet/3com/3c515.c:1530:66: error: implicit conversion from 'int' to 'short' changes value from 32783 to -32753 [-Werror,-Wconstant-conversion]
new_mode = SetRxFilter | RxStation | RxMulticast | RxBroadcast | RxProm;
~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~
drivers/net/ethernet/3com/3c515.c:1532:52: error: implicit conversion from 'int' to 'short' changes value from 32775 to -32761 [-Werror,-Wconstant-conversion]
new_mode = SetRxFilter | RxStation | RxMulticast | RxBroadcast;
~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~
drivers/net/ethernet/3com/3c515.c:1534:38: error: implicit conversion from 'int' to 'short' changes value from 32773 to -32763 [-Werror,-Wconstant-conversion]
new_mode = SetRxFilter | RxStation | RxBroadcast;
~ ~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~
Make the variable unsigned to avoid the overflow.
Fixes: Linux-2.1.128pre1
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using 16K DMA buffers and ring mode, the DES3 refill is not working
correctly as the function is using a bogus pointer for checking the
private data. As a result stale pointers will remain in the RX descriptor
ring, so DMA will now likely overwrite/corrupt some already freed memory.
As simple reproducer, just receive some UDP traffic:
# ifconfig eth0 down; ifconfig eth0 mtu 9000; ifconfig eth0 up
# iperf3 -c 192.168.253.40 -u -b 0 -R
If you didn't crash by now check the RX descriptors to find non-contiguous
RX buffers:
cat /sys/kernel/debug/stmmaceth/eth0/descriptors_status
[...]
1 [0x2be5020]: 0xa3220321 0x9ffc1ffc 0x72d70082 0x130e207e
^^^^^^^^^^^^^^^^^^^^^
2 [0x2be5040]: 0xa3220321 0x9ffc1ffc 0x72998082 0x1311a07e
^^^^^^^^^^^^^^^^^^^^^
A simple ping test will now report bad data:
# ping -s 8200 192.168.253.40
PING 192.168.253.40 (192.168.253.40) 8200(8228) bytes of data.
8208 bytes from 192.168.253.40: icmp_seq=1 ttl=64 time=1.00 ms
wrong data byte #8144 should be 0xd0 but was 0x88
Fix the wrong pointer. Also we must refill DES3 only if the DMA buffer
size is 16K.
Fixes: 54139cf3bb33 ("net: stmmac: adding multiple buffers for rx")
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A recently added function in mlxsw triggers a harmless compiler warning:
In file included from drivers/net/ethernet/mellanox/mlxsw/core.h:17,
from drivers/net/ethernet/mellanox/mlxsw/core_env.c:7:
drivers/net/ethernet/mellanox/mlxsw/core_env.c: In function 'mlxsw_env_module_temp_thresholds_get':
drivers/net/ethernet/mellanox/mlxsw/reg.h:8015:45: error: '*' in boolean context, suggest '&&' instead [-Werror=int-in-bool-context]
#define MLXSW_REG_MTMP_TEMP_TO_MC(val) (val * 125)
~~~~~^~~~~~
drivers/net/ethernet/mellanox/mlxsw/core_env.c:116:8: note: in expansion of macro 'MLXSW_REG_MTMP_TEMP_TO_MC'
if (!MLXSW_REG_MTMP_TEMP_TO_MC(module_temp)) {
^~~~~~~~~~~~~~~~~~~~~~~~~
The warning is normally disabled, but it would be nice to enable
it to find real bugs, and there are no other known instances at
the moment.
Replace the negation with a zero-comparison, which also matches
the comment above it.
Fixes: d93c19a1d95c ("mlxsw: core: Add API for QSFP module temperature thresholds reading")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Kalle Valo says:
====================
wireless-drivers fixes for 5.1
First set of fixes for 5.1. Lots of fixes for mt76 this time.
iwlwifi
* fix warning with do_div()
mt7601u
* avoid using hardware which is supported by mt76
mt76
* more fixes for hweight8() usage
* fix hardware restart for mt76x2
* fix writing txwi on USB devices
* fix (and disable by default) ED/CCA support on 76x2
* fix powersave issues on 7603
* fix return value check for ioremap on 7603
* fix duplicate USB device IDs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
My commit 26a7b5473191 ("mt76x02: set protection according to ht
operation element") enabled by default RTS/CTS protection for OFDM
and CCK traffic, because MT_TX_RTS_CFG_THRESH is configured to non
0xffff by initvals and .set_rts_threshold callback is not called by
mac80211 on initialization, only on user request or during
ieee80211_reconfig() (suspend/resuem or restart_hw).
Enabling RTS/CTS cause some problems when sending probe request
frames by hcxdumptool penetration tool, but I expect it can cause
other issues on different scenarios.
Restore previous setting of RTS/CTS being disabled by default for
OFDM/CCK by changing MT_TX_RTS_CFG_THRESH initvals to 0xffff.
Fixes: 26a7b5473191 ("mt76x02: set protection according to ht operation element")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fix following schedule while atomic in mt76x02_reset_state
since synchronize_rcu is run inside a RCU section
[44036.944222] mt76x2e 0000:06:00.0: MCU message 31 (seq 3) timed out
[44036.944281] BUG: sleeping function called from invalid context at kernel/rcu/tree_exp.h:818
[44036.944284] in_atomic(): 1, irqs_disabled(): 0, pid: 28066, name: kworker/u4:1
[44036.944287] INFO: lockdep is turned off.
[44036.944292] CPU: 1 PID: 28066 Comm: kworker/u4:1 Tainted: G W 5.0.0-rc7-wdn-t1+ #7
[44036.944294] Hardware name: Dell Inc. Studio XPS 1340/0K183D, BIOS A11 09/08/2009
[44036.944305] Workqueue: phy1 mt76x02_wdt_work [mt76x02_lib]
[44036.944308] Call Trace:
[44036.944317] dump_stack+0x67/0x90
[44036.944322] ___might_sleep.cold.88+0x9f/0xaf
[44036.944327] rcu_blocking_is_gp+0x13/0x50
[44036.944330] synchronize_rcu+0x17/0x80
[44036.944337] mt76_sta_state+0x138/0x1d0 [mt76]
[44036.944349] mt76x02_wdt_work+0x1c9/0x610 [mt76x02_lib]
[44036.944355] process_one_work+0x2a5/0x620
[44036.944361] worker_thread+0x35/0x3e0
[44036.944368] kthread+0x11c/0x140
[44036.944376] ret_from_fork+0x3a/0x50
[44036.944384] BUG: scheduling while atomic: kworker/u4:1/28066/0x00000002
[44036.944387] INFO: lockdep is turned off.
[44036.944389] Modules linked in: cmac ctr ccm af_packet snd_hda_codec_hdmi
Introduce __mt76_sta_remove in order to run sta_remove without holding dev->mutex.
Move __mt76_sta_remove outside of RCU section in mt76x02_reset_state
Fixes: e4ebb8b403d1 ("mt76: mt76x2: implement full device restart on watchdog reset")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
__sw_hweight8() is only defined if CONFIG_GENERIC_HWEIGHT is enabled.
The function that works on all architectures is hweight8().
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since some USB device IDs are duplicated between mt76x0u, mt7601u
and mt76x2u device, check chip version on probe and return error if
not match the driver.
Don't think this is serious issue, probe most likely will fail at
some other point for wrong device, but we do not have to configure
it if we know is not our device.
Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since some USB device IDs are duplicated between mt7601u and mt76x0u
devices, check chip version on probe and return error if not match
0x7601.
Don't think this is serious issue, probe most likely will fail at
some other point for wrong device, but we do not have to configure
it if we know is not mt7601u device.
Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
|
|
Commit ad6c9986bcb62 ("vxlan: Fix GRO cells race condition between
receive and link delete") fixed a race condition for the typical case a vxlan
device is dismantled from the current netns. But if a netns is dismantled,
vxlan_destroy_tunnels() is called to schedule a unregister_netdevice_queue()
of all the vxlan tunnels that are related to this netns.
In vxlan_destroy_tunnels(), gro_cells_destroy() is called and finished before
unregister_netdevice_queue(). This means that the gro_cells_destroy() call is
done too soon, for the same reasons explained in above commit.
So we need to fully respect the RCU rules, and thus must remove the
gro_cells_destroy() call or risk use after-free.
Fixes: 58ce31cca1ff ("vxlan: GRO support at tunnel layer")
Signed-off-by: Suanming.Mou <mousuanming@huawei.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TCP/UDP checksum validity was propagated to skb
only if IP checksum is valid.
But for IPv6 there is no validity as there is no checksum in IPv6.
This patch propagates TCP/UDP checksum validity regardless of IP checksum.
Fixes: 018423e90bee ("net: ethernet: aquantia: Add ring support code")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bug that Stan reported is as follows. After a restart, a 16-bit NIC
may be incorrectly identified as a 32-bit NIC and stop working.
mac8390 slot.E: Memory length resource not found, probing
mac8390 slot.E: Farallon EtherMac II-C (type farallon)
mac8390 slot.E: MAC 00:00:c5:30:c2:99, IRQ 61, 32 KB shared memory at 0xfeed0000, 32-bit access.
The bug never arises after a cold start and only intermittently after a
warm start. (I didn't investigate why the bug is intermittent.)
It turns out that memcpy_toio() is deprecated and memcmp_withio() also
has issues. Replacing these calls with mmio accessors fixes the problem.
Reported-and-tested-by: Stan Johnson <userm57@yahoo.com>
Fixes: 2964db0f5904 ("m68k: Mac DP8390 update")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similarly to commit a7603ac1fc8c ("geneve: change NET_UDP_TUNNEL
dependency to select"), GTP has a dependency on NET_UDP_TUNNEL which
makes impossible to compile it if no other protocol depending on
NET_UDP_TUNNEL is selected.
Fix this by changing the depends to a select, and drop NET_IP_TUNNEL from
the select list, as it already depends on NET_UDP_TUNNEL.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In my latest patch I missed one rcu_read_unlock(), in case
device is down.
Fixes: 4477138fa0ae ("tun: properly test for IFF_UP")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Same reasons than the ones explained in commit 4179cb5a4c92
("vxlan: test dev->flags & IFF_UP before calling netif_rx()")
netif_rx_ni() or napi_gro_frags() must be called under a strict contract.
At device dismantle phase, core networking clears IFF_UP
and flush_all_backlogs() is called after rcu grace period
to make sure no incoming packet might be in a cpu backlog
and still referencing the device.
A similar protocol is used for gro layer.
Most drivers call netif_rx() from their interrupt handler,
and since the interrupts are disabled at device dismantle,
netif_rx() does not have to check dev->flags & IFF_UP
Virtual drivers do not have this guarantee, and must
therefore make the check themselves.
Fixes: 1bd4978a88ac ("tun: honor IFF_UP in tun_get_user()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If an interrupt is already pending when the interrupt is enabled on the
GXL phy, no IRQ will ever be triggered.
The fix is simply to make sure pending IRQs are cleared before setting
up the irq mask.
Fixes: cf127ff20af1 ("net: phy: meson-gxl: add interrupt support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are several statements that contain extra spacing in
the indentation; clean this up by removing spaces. Also
add { } braces on if statement to keep to kernel coding
style.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a statement that is indented incorrectly; replace
spaces with a tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netdev_alloc_skb can fail and return a NULL pointer which is
dereferenced without a check. The patch avoids such a scenario.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When sending non-linear skbs with jumbo frames, we set up the non-paged
data and mark that as a last segment, although the paged fragments are
also prepared. This will stall the TX queue and trigger a watchdog warning
(a simple reproducer is to run an iperf client mode TCP test with a large
MTU - networking fails instantly).
Fix by checking if the skb is non-linear.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 0e80bdc9a72d ("stmmac: first frame prep at the end of xmit
routine") overlooked jumbo frames when re-ordering the code, and as a
result the own bit was not getting set anymore for the first jumbo frame
descriptor. Commit 487e2e22ab79 ("net: stmmac: Set OWN bit for jumbo
frames") tried to fix this, but now the bit is getting set too early and
the DMA may start while we are still setting up the remaining descriptors.
And with the chain mode the own bit remains still unset.
Fix by setting the own bit at the end of xmit also with jumbo frames.
Fixes: 0e80bdc9a72d ("stmmac: first frame prep at the end of xmit routine")
Fixes: 487e2e22ab79 ("net: stmmac: Set OWN bit for jumbo frames")
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
"More fixes in the queue:
1) Netfilter nat can erroneously register the device notifier twice,
fix from Florian Westphal.
2) Use after free in nf_tables, from Pablo Neira Ayuso.
3) Parallel update of steering rule fix in mlx5 river, from Eli
Britstein.
4) RX processing panic in lan743x, fix from Bryan Whitehead.
5) Use before initialization of TCP_SKB_CB, fix from Christoph Paasch.
6) Fix locking in SRIOV mode of mlx4 driver, from Jack Morgenstein.
7) Fix TX stalls in lan743x due to mishandling of interrupt ACKing
modes, from Bryan Whitehead.
8) Fix infoleak in l2tp_ip6_recvmsg(), from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
pptp: dst_release sk_dst_cache in pptp_sock_destruct
MAINTAINERS: GENET & SYSTEMPORT: Add internal Broadcom list
l2tp: fix infoleak in l2tp_ip6_recvmsg()
net/tls: Inform user space about send buffer availability
net_sched: return correct value for *notify* functions
lan743x: Fix TX Stall Issue
net/mlx4_core: Fix qp mtt size calculation
net/mlx4_core: Fix locking in SRIOV mode when switching between events and polling
net/mlx4_core: Fix reset flow when in command polling mode
mlxsw: minimal: Initialize base_mac
mlxsw: core: Prevent duplication during QSFP module initialization
net: dwmac-sun8i: fix a missing check of of_get_phy_mode
net: sh_eth: fix a missing check of of_get_phy_mode
net: 8390: fix potential NULL pointer dereferences
net: fujitsu: fix a potential NULL pointer dereference
net: qlogic: fix a potential NULL pointer dereference
isdn: hfcpci: fix potential NULL pointer dereference
Documentation: devicetree: add a new optional property for port mac address
net: rocker: fix a potential NULL pointer dereference
net: qlge: fix a potential NULL pointer dereference
...
|
|
sk_setup_caps() is called to set sk->sk_dst_cache in pptp_connect,
so we have to dst_release(sk->sk_dst_cache) in pptp_sock_destruct,
otherwise, the dst refcnt will leak.
It can be reproduced by this syz log:
r1 = socket$pptp(0x18, 0x1, 0x2)
bind$pptp(r1, &(0x7f0000000100)={0x18, 0x2, {0x0, @local}}, 0x1e)
connect$pptp(r1, &(0x7f0000000000)={0x18, 0x2, {0x3, @remote}}, 0x1e)
Consecutive dmesg warnings will occur:
unregister_netdevice: waiting for lo to become free. Usage count = 1
v1->v2:
- use rcu_dereference_protected() instead of rcu_dereference_check(),
as suggested by Eric.
Fixes: 00959ade36ac ("PPTP: PPP over IPv4 (Point-to-Point Tunneling Protocol)")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It has been observed that tx queue may stall while downloading
from certain web sites (example www.speedtest.net)
The cause has been tracked down to a corner case where
the tx interrupt vector was disabled automatically, but
was not re enabled later.
The lan743x has two mechanisms to enable/disable individual
interrupts. Interrupts can be enabled/disabled by individual
source, and they can also be enabled/disabled by individual
vector which has been mapped to the source. Both must be
enabled for interrupts to work properly.
The TX code path, primarily uses the interrupt enable/disable of
the TX source bit, while leaving the vector enabled all the time.
However, while investigating this issue it was noticed that
the driver requested the use of the vector auto clear feature.
The test above revealed a case where the vector enable was
cleared unintentionally.
This patch fixes the issue by deleting the lines that request
the vector auto clear feature to be used.
Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
genlmsg_reply can fail, so propagate its return code
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
|
|
In case alloc_ordered_workqueue fails, the fix releases
sources and returns -ENOMEM to avoid NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
|
|
Calculation of qp mtt size (in function mlx4_RST2INIT_wrapper)
ultimately depends on function roundup_pow_of_two.
If the amount of memory required by the QP is less than one page,
roundup_pow_of_two is called with argument zero. In this case, the
roundup_pow_of_two result is undefined.
Calling roundup_pow_of_two with a zero argument resulted in the
following stack trace:
UBSAN: Undefined behaviour in ./include/linux/log2.h:61:13
shift exponent 64 is too large for 64-bit type 'long unsigned int'
CPU: 4 PID: 26939 Comm: rping Tainted: G OE 4.19.0-rc1
Hardware name: Supermicro X9DR3-F/X9DR3-F, BIOS 3.2a 07/09/2015
Call Trace:
dump_stack+0x9a/0xeb
ubsan_epilogue+0x9/0x7c
__ubsan_handle_shift_out_of_bounds+0x254/0x29d
? __ubsan_handle_load_invalid_value+0x180/0x180
? debug_show_all_locks+0x310/0x310
? sched_clock+0x5/0x10
? sched_clock+0x5/0x10
? sched_clock_cpu+0x18/0x260
? find_held_lock+0x35/0x1e0
? mlx4_RST2INIT_QP_wrapper+0xfb1/0x1440 [mlx4_core]
mlx4_RST2INIT_QP_wrapper+0xfb1/0x1440 [mlx4_core]
Fix this by explicitly testing for zero, and returning one if the
argument is zero (assuming that the next higher power of 2 in this case
should be one).
Fixes: c82e9aa0a8bc ("mlx4_core: resource tracking for HCA resources used by guests")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In procedures mlx4_cmd_use_events() and mlx4_cmd_use_polling(), we need to
guarantee that there are no FW commands in progress on the comm channel
(for VFs) or wrapped FW commands (on the PF) when SRIOV is active.
We do this by also taking the slave_cmd_mutex when SRIOV is active.
This is especially important when switching from event to polling, since we
free the command-context array during the switch. If there are FW commands
in progress (e.g., waiting for a completion event), the completion event
handler will access freed memory.
Since the decision to use comm_wait or comm_poll is taken before grabbing
the event_sem/poll_sem in mlx4_comm_cmd_wait/poll, we must take the
slave_cmd_mutex as well (to guarantee that the decision to use events or
polling and the call to the appropriate cmd function are atomic).
Fixes: a7e1f04905e5 ("net/mlx4_core: Fix deadlock when switching between polling and event fw commands")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As part of unloading a device, the driver switches from
FW command event mode to FW command polling mode.
Part of switching over to polling mode is freeing the command context array
memory (unfortunately, currently, without NULLing the command context array
pointer).
The reset flow calls "complete" to complete all outstanding fw commands
(if we are in event mode). The check for event vs. polling mode here
is to test if the command context array pointer is NULL.
If the reset flow is activated after the switch to polling mode, it will
attempt (incorrectly) to complete all the commands in the context array --
because the pointer was not NULLed when the driver switched over to polling
mode.
As a result, we have a use-after-free situation, which results in a
kernel crash.
For example:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff876c4a8e>] __wake_up_common+0x2e/0x90
PGD 0
Oops: 0000 [#1] SMP
Modules linked in: netconsole nfsv3 nfs_acl nfs lockd grace ...
CPU: 2 PID: 940 Comm: kworker/2:3 Kdump: loaded Not tainted 3.10.0-862.el7.x86_64 #1
Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS 090006 04/28/2016
Workqueue: events hv_eject_device_work [pci_hyperv]
task: ffff8d1734ca0fd0 ti: ffff8d17354bc000 task.ti: ffff8d17354bc000
RIP: 0010:[<ffffffff876c4a8e>] [<ffffffff876c4a8e>] __wake_up_common+0x2e/0x90
RSP: 0018:ffff8d17354bfa38 EFLAGS: 00010082
RAX: 0000000000000000 RBX: ffff8d17362d42c8 RCX: 0000000000000000
RDX: 0000000000000001 RSI: 0000000000000003 RDI: ffff8d17362d42c8
RBP: ffff8d17354bfa70 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000298 R11: ffff8d173610e000 R12: ffff8d17362d42d0
R13: 0000000000000246 R14: 0000000000000000 R15: 0000000000000003
FS: 0000000000000000(0000) GS:ffff8d1802680000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 00000000f16d8000 CR4: 00000000001406e0
Call Trace:
[<ffffffff876c7adc>] complete+0x3c/0x50
[<ffffffffc04242f0>] mlx4_cmd_wake_completions+0x70/0x90 [mlx4_core]
[<ffffffffc041e7b1>] mlx4_enter_error_state+0xe1/0x380 [mlx4_core]
[<ffffffffc041fa4b>] mlx4_comm_cmd+0x29b/0x360 [mlx4_core]
[<ffffffffc041ff51>] __mlx4_cmd+0x441/0x920 [mlx4_core]
[<ffffffff877f62b1>] ? __slab_free+0x81/0x2f0
[<ffffffff87951384>] ? __radix_tree_lookup+0x84/0xf0
[<ffffffffc043a8eb>] mlx4_free_mtt_range+0x5b/0xb0 [mlx4_core]
[<ffffffffc043a957>] mlx4_mtt_cleanup+0x17/0x20 [mlx4_core]
[<ffffffffc04272c7>] mlx4_free_eq+0xa7/0x1c0 [mlx4_core]
[<ffffffffc042803e>] mlx4_cleanup_eq_table+0xde/0x130 [mlx4_core]
[<ffffffffc0433e08>] mlx4_unload_one+0x118/0x300 [mlx4_core]
[<ffffffffc0434191>] mlx4_remove_one+0x91/0x1f0 [mlx4_core]
The fix is to set the command context array pointer to NULL after freeing
the array.
Fixes: f5aef5aa3506 ("net/mlx4_core: Activate reset flow upon fatal command cases")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently base_mac is not initialized which causes wrong reporting of
zeroed parent_id to userspace. Fix this by initializing base_mac
properly.
Fixes: c100e47caa8e ("mlxsw: minimal: Add ethtool support")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Verify during thermal initialization if QSFP module's entry is already
configured in order to prevent duplication.
Such scenario could happen in case two switch drivers (PCI and I2C
based) coexist and if after boot, splitting configuration is applied
for some ports and then I2C based driver is re-probed.
In such case after reboot same QSFP module, associated with split will
be discovered by I2C based driver few times, and it will cause a crash.
It could happen for example on system equipped with BMC (Baseboard
Management Controller), running I2C based driver, when the next steps
are performed:
- System boot
- Host side configures port spilt.
- BMC side is rebooted.
Fixes: 6a79507cfe94 ("mlxsw: core: Extend thermal module with per QSFP module thermal zones")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
of_get_phy_mode may fail and return a negative error code;
the fix checks the return value of of_get_phy_mode and
returns -EINVAL of it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
of_get_phy_mode may fail and return a negative error code;
the fix checks the return value of of_get_phy_mode and
returns NULL of it fails.
Fixes: b356e978e92f ("sh_eth: add device tree support")
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case ioremap fails, the fix releases resources and returns
to avoid NULL pointer dereferences.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case ioremap fails, the fix releases the pcmcia window and
returns -ENOMEM to avoid the NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case create_singlethread_workqueue fails, the fix returns
-ENOMEM to avoid NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-03-11
For -stable v5.0:
('net/mlx5e: Fix access to non-existing receive queue')
('net/mlx5e: Properly get the PF number phys port name ndo')
('net/mlx5: Fix multiple updates of steering rules in parallel')
('net/mlx5: Avoid panic when setting vport mac, getting vport config')
('net/mlx5: Avoid panic when setting vport rate')
('net/mlx5e: IPoIB, Fix RX checksum statistics update')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case kzalloc fails, the fix releases resources and returns
NOTIFY_BAD to avoid NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case alloc_ordered_workqueue fails, the fix returns
-ENOMEM to avoid NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case alloc_ordered_workqueue fails, the fix reports the error
and returns -ENOMEM.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Harini Katakam
Dan Murphy
Ioana Ciocoi Radulescu
Lukas Wunner
Arnd Bergmann
Aaro Koskinen
David S. Miller
Stanislaw Gruszka
Lorenzo Bianconi
Felix Fietkau
Stefan Schmidt
Zhiqiang Liu
Dmitry Bogdanov
Finn Thain
Matteo Croce
Eric Dumazet
Jerome Brunet
Colin Ian King
Aditya Pakki
Linus Torvalds
Xin Long
Bryan Whitehead
Li RongQing
Kangjie Lu
Jack Morgenstein
Jiri Pirko
Vadim Pasternak